04252019JA 1 www.epvscreens.com
Power Max Sonic 2 Series
Acoustically Transparent Tab-Tensioned Motorized
Projection Screen
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop limit. There is NO extra black-
matte drop material on the roller. Please be aware that altering the vertical limit switch to drop the screen
material off the roller voids your warranty with EPV Screens. Unapproved changes or modifications (except
for cutting the power cord for hardwire installations) to this unit are prohibited and will likewise void your
warranty.
For more information, please contact our Technical Support Department at (877) 511-1211 Ext. 604.
• Please retain this user’s guide for future reference.
• To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the
manufacturer.
• Handle the unit carefully during transportation to avoid any damages.
• To ensure safe and reliable operation, make sure the power connection is secure.
• The power source should be close to the unit and easily accessible.
• Do not install the unit on uneven, or inclined surfaces;
• To avoid electrical shock or product damage, do not install this device in a damp place.
• Do not place any heavy objects over the power cord.
• Position the power cord properly to avoid creating a trip hazard.
• Avoid electrical shock or fire, by not overloading the power cord.
• The internal & external parts of this unit are not end user serviceable. Do not attempt to
disassemble this unit by yourself. Consult an authorized technician instead.
• Make sure the power source that this unit is connected to has a continuous power flow.
• If there is need to use an extension cord, make sure said cord has a compatible power rating.
• Do not handle this or any other electrical device if you are wet or standing in water.
• Whenever the screen reaches its end of life, follow local environmental guidelines regarding its
proper disposal.
04252019JA 2 www.epvscreens.com
Do not use this unit under the following circumstances.
• Disconnect the power cord if exposed to moisture, rain, wind, electrical storms or snow.
• Avoid exposure to direct sunlight or any of the conditions stated in the previous bullet point.
• Keep away from fire or other high temperature heat sources.
• Cut off the power supply first before attempting maintenance or removal.
• Do not attempt to use this screen if there are obvious signs of damage.
• To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is
obvious damage or if there are any evident broken parts.
WARNING
Individual modifications to this product are prohibited and will void the manufacturer’s warranty. Please
contact the EPV Screens Customer Service Team with any questions.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
The product settings are designed to provide reasonable protection against any radio interference within a
residential installation. If properly installed, the Saker Tab-Tension screen may suffer from RF interference
from other home electronics.
Although radio interference affecting other household electronics is unlikely, the following steps can be
taken should RF interference occur.
✓ Reorient or relocate the receiving antenna on the device that may be casing the interference.
✓ Increase the distance between the screen and the interfering device’s receiver.
✓ Connect the projection screen to another power source apart from the interfering device.
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen upright on a clean, level surface.
3. Keep the screen out of contact with foreign particles such as dust, sawdust, and/or liquids.
NOTE
Regardless of the mounting method, each screen should be securely installed so that vibrations or pulling on
the viewing surface will not cause the casing to become loose or fall. Included are complimentary mounting
screws that may or may not be appropriate for the installation you are attempting. Always use the correct
anchors to safely secure the screen. This product is for professional integrators only.
Hardware Parts List
Please make sure all parts listed below are included before proceeding with the installation.
A.
Wall/Ceiling
mount
bracket x2
B.
M5x60
Screw
x6
C. M12
Dry-wall
anchor x6
D. Bracket
connector x2
(Installed on
the housing)
E. M5x11
Bolt Screw
x4
(Screw on
the D parts)
F.
M5x25M
M round
head cross
screws x2
G.
M5x30M
M eyebolt
screw &
M5 nut x2
H.
Carabiner
x2
04252019JA 3 www.epvscreens.com
Installation Instructions
For installation assistance, please consult a professional Installer. EPV Screens is not liable for faulty installations.
A. Wall Mount
Flush mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and bottom
screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked points and install the brackets with the dry-wall anchor(C), M5x60 screw (B), Make
sure both brackets are properly leveled.
3. Hang the screen by placing the downward “catch” located on the back over the bracket’s upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
Two or more people are required while one holds the screen in place.
B. Ceiling Mount
I. Ceiling Mount (movable position)
This mount method allows the screen to slide horizontally.
1. Determine where the screen will be installed. Then, measure and mark the distance between the top and bottom
screw holes from each Wall/Ceiling mount bracket (A).
2. Drill a hole on all marked points and install the brackets with the dry-wall anchor(C), M5x60 screw (B), Make
sure both brackets are properly leveled.
3. Hang the screen by placing the lower “catch” located on the back over the bracket’s upper “catch”.
4. After making sure the screen is secured, you can slide it left / right to properly center it in position.
5. Lastly, screw the M5 screw (F) into the upper hole of the bracket to add additional support for the screen.
Two or more people are required while one holds the screen in place.
II. Suspended
1. Screw the eyebolt (G) on the bracket connector (D).
2. Attach the snap link (H) through the eyebolt (G) and connect it to an eyebolt screw (not included) rated for the
screen’s weight.
Front view of bracket (A)
M5x25MM round
head cross screws
(F)
Side view of bracket (A)
Wall
Ceiling
Front view of
bracket (A)
M5x25MM
round head
cross screws (F)
Ceilin
04252019JA 4 www.epvscreens.com
Screen material tension adjustment
(4mm Allen Wrench required and not included)
Remove the weight bar end cap to expose the
adjustment tension knob. This knob has a 4mm Allen
port. Insert your 4mm Allen Wrench and push in the
adjustment tension knob, turn clockwise and your
screen will gain more tension. Turn the Allen Wrench
counter clockwise and the screen will lose tension.
Please note this adjustment is not necessary as the
tension of the screen has been pre-set to its factory
drop setting. If you would like to adjust the screen
tension, please contact EPV Screens for assistance to
avoid damaging the screen and voiding your warranty.
Power Max Sonic 2 Series | Controls and Accessories
A. IR
Remote
B. RF
Remote
C. Wall
switch
control box
D. 5-12-volt
trigger
cable
E. IR
extended
“eye”
receiver
F. Wireless
5-12v
trigger
cable
G. AAA
batteries
H. Bubble leveler
Screen operation
Electric Current: Depending upon region, your screen will operate at 100v, 110v, or 220v voltage.
1. After ensuring the power outlet & screen are compatible (voltage), plug the power cord into the power outlet.
2. Once the screen has power, you’ll be able to control it using any of the 6 methods described below.
6 ways to control your Saker Tab-Tension
1. IR remote control (Item A, Fig 1): The Infrared functions by direct line of sight
contact using a beam range of 30 feet. Aim the IR remote at the circular window
located on the left side of the screen.
2. IR “Eye” Receiver (Item E, Fig 2): The IR “Eye” Receiver plugs directly into
the screen’s RJ-45 input to present a low-profile line-of-sight control option for
your IR remote control. It is an extended eye-receiver to accommodate a recessed
ceiling installation.
3. RF Remote Control (Item B, Fig 1): The radio waves
eliminate the need for a direct line of sight and has a range
of 100 feet.
Fig.2
UP
STOP
DOWN
IR “eye” receiver
Fig.1
IR/RF remote
04252019JA 5 www.epvscreens.com
UP
St op
Down
4. 3-Way Wall Switch (Item C, Fig 3): The 3-way wall switch
is a wall mounted control box with an up/stop/down button. It
plugs directly into the screen’s RJ-45 input.
5. 5-12 volt trigger (Item D, Fig 4): The built-in 5-12V trigger
input allows your screen to synchronize its drop & rise with the
projector’s power cycle. The screen deploys when the projector
powers up and will retract when the projector powers down. The
5-12 volt RJ45 cable connects to your projector’s trigger output
via a separate cable that may or may not be provided by the
manufacturer of the projector. The trigger feature will not work
without an output cable from the projector, but it can be tested
by connecting the Red (+) and Green (-) cable to a 9volt battery.
6. Wireless 5-12 volt trigger (Item F, Fig 5): The RF
remote control serves as a dual purpose, independently
as a handheld remote control, or as a Wireless 5-12
volt trigger using the trigger cable. The radio
frequency technology can be programmed to send a
wireless signal that synchronizes screen drop & rise
with the projector’s power cycle.
Here’s how to set up your Wireless 5-12 volt
trigger | Synchronization Instructions
Step1: Connect one end of the 3.5 mm wireless 5-12
volt trigger cable to the RF remote.
Step 2: Connect the other 3.5 mm end of the wireless 5-12 volt trigger cable to your projector
Step 3: Make sure to unplug your screen from the power outlet
Step 4: Hold the UP button on your RF remote
Step 5: While holding the UP button, plug the screen back to the power outlet
Step 6: Wait 5 seconds and then release the UP button
Step 7: Your 5-12V wireless trigger should now be activated with your screen and ready to be used and
able to control your screen with your projector’s power cycle
Repeat the steps again if not successful.
(Please be aware, the projector on/off cycle may take longer to fully activate. It usually takes around 20-
30seconds for full off and on cycle each time)
For more information, technical support or your local EPV Screens contact, please
visit www.epvscreens.com
DC 5-12V out
Wireless 5-12V
trigger cable
The back of the
projector
Fig.4
3 prong power cord
RJ45 Input
5-12 volt trigger cable
Fig 5
Fig.3
3 Way Wall Switch
(does not have IR sensor)
Loading...