Epson MX-80F, MX-80T User Manual

MX-80F/T

EPSON DOT MATRIX PRINTER

Operation Manual

EPSON

P8093033-1

Shinshu Seiki Co., Ltd.

Nagano, Japan

*The contents of this manual are subject to change without notice.

TRS-80 is the registered trademark of Radio Shack,

a Division of Tandy Corporation.

TABLE OF CONTENTS

INTRODUCTION INSTALLATION.

1. Contents of Carton.

2. Unpacking.

2.1. Unpacking steps

2.2. Repacking steps.

3. Installation of the Printer

4. Cartridge Ribbon Setting.

5. Separator Installation.

6. Dismounting of Tractor Unit.

7. Paper Loading

7.1. Fanfold paper.

7.1.1. Loading of fanfold paper

7.1.2. Removal of fanfold paper.

7.1.3. Column layout on fanfold paper.

7.1.4. Top of form position setting

7.2. Roll paper.

7.2.1. Roll paper holder.

7.2.2. Loading of roll paper

7.3. Cut paper sheet.

7.3.1. Loading of cut paper sheet

8. Gap Adjustment

9. Power Connection OPERATION.

1. Switches and Indicators

1.1. Switches

1.2. Indicators

.....................

...............

.......................

.................

..........

.............

.......

....................

...................

.........

........

......

......................

...............

............

.................

.......

..................

................

........................

...........

........................

.......................

2. Buzzer...........................

3. Paper End Detector

...............

4. Self-Test.........................

5. Construction of MX-80 F/T

5.1. Printer mechanism.

...............

5.2. Control circuit board.

5.3. Power circuit

5.4. Printer initialization

....................

...............

6. Setting of DIP Switches.

7. Parallel Interface.

8. Coding Tables

9. Control Codes

.................

....................

........

.............

..........

. . .. . .1

. .

. . . . . .

. . .

. . . . . .

. . , . .

. . . . . . . .

. . . . .

. . .

. . . .

. .

. . .

. .

. . . .

18 . . .20 . . .20 . .20 . .

21 . .

21 . 22 . .23 . . .23 . .

. . . .28

. . . .

2 2 3 3 3 3 6 7

9 9

. . . .

. .

. . .

. .

. . .

. .

. . .

. .

. . .

. .

. . .

. . . .

. .

. . . . .

. . .

-(1)-

MAINTENANCE .........................

1. Preventive Maintenance. ..............

2. Parts Replacement SPECIFICATIONS

....................

........................

SUMMARY OF CONTROL CODES. ........

APPENDIX ..............................

Assembly Instructions on Roll Paper Holder

44 44 44 46 48

49 49

-(2)--

LIST OF FIGURES

Fig. 1

Fig. 2 Fig. 3 Fig. 4 Fig. 5

Fig. 6

Fig. 7

Fig. 8 Fig. 9

EPSON MX-80 F/T Dot Matrix Printer Contents of Carton. Removal of Shipping Screws Removal of Printer Lid.

Cartridge Ribbon Setting.

..............................................

.....................................

...........................................

.........................................

Examples of Correct and Incorrect Ribbon Setting. Separator Installation Dismounting of Tractor Unit,

........................

.....................................

..............................

...................

.....................

Fig. 10 Mounting of Tractor Unit Fig. 11 lnsertion of Fanfold Paper.

Fig. 12 Raising of Sprocket Lock Levers Fig. 13 Engagement of Paper Feed Holes on Feeding Pins.

Fig. 14 Printer with Fanfold Paper Set Completely Fig. 15 Example of Paper Arrangement.

Fig. 16 Top of Form Position Setting.

Fig. 17 Loading of Roll Paper (1) Fig. 18 Loading of Roll Paper (2) Fig. 19 Loading of Roll Paper (3) Fig. 20 Loading of Cut Paper Sheet. Fig. 21 Adjustment of Inserted Paper Position Fig. 22 Alignment of Side edges. Fig. 23 Form Position Setting Mark

Fig. 24 Print Area.

.....................................................

Fig. 25 Setting of Cut Paper Sheet. Fig. 26 Printer with Cut Paper Sheet Set Completely Fig. 27 Gap Adjustment.

...............................................

Fig. 28 Switches and Indicators on Control Panel Fig. 29 Control Circuit Diagram. Fig. 30 Driver Circuit Diagram Fig. 31 Location of DIP Switches Fig. 32 Parallel Interface Timing Fig. 33 Replacement of Print Head.

...............................................................................

..................................

..................

.........................

..................................

....................................

........................................

.....................................

.............................

........................................

......................................

.......................

..........................

.........................................

...........................................

........................................

.........................................

.....................................

. 10

10 11 11 12 13

14 14

15 15 16 16 16 17 17 19 20 24 25 27 31

.45

1 2

5 6

7 7

-(3)-

LIST OF TABLES

Table 1 Interface Signals in Paper-Out Status Table 2 Functions and Conditions of DIPSwitch 1. Table 3 Functions and Conditions of DIPSwitch 2.

.........................

.....................

22 27 28

Table 4 Special Characters/Symbols Available for Selection

(using DIP Switch Pins 2-1 and 2-2).

.........................

Table 5 Connector Pin Assignment and Descriptions of Interface Signals. Table5 (cont.) Table 6 Coding Table (Standard) Table 7 Coding Table (TRS-80) Table 6 Special Characters/Symbols Table 9 DC 1 /DC3 and Data Entry.

....................................................

....................................

.....................................

.................................

...................................

28 29 30 32 33 34 38

-(4)-

INTRODUCTION

The EPSON MX-80 F/T Dot Matrix Printer is a highly versatile, general-purpose and computer-grade printer featuring 80 CPS bi-directional printing with logical seeking capability and 9 X 9 dot-matrix character formation. The MX-80 F/T accepts the

ASCII 96 codes and codes for special characters/symbols (e.g.. b; C accepts codes for 64 graphic patterns. Characters can be printed in any desired size - enlarged, condensed, emphasized, normal, etc. The one-chip microprocessor is engaged in performing all functions of the Printer and the two built-in stepper motors of the MX-80 F/T control the carriage and paper feeding functions respectively. Therefore, versatile software controls, such as horizontal and vertical tabs, and form feed are at your disposal.

The MX-80 F/T is capable of S-way paper handling such as fanfold paper,roll paper

and cut paper sheet. In addition, various interface options are available to permit handshaking with most personal computers.

2).

It also

Fig. 1.

EPSON MX-80 F/T Dot Matrix Printer

-1-

INSTALLATION

1. Contents of Carton

The MX-80 F/T and standard accessories are as shown in Fig. 2. Upon unpack-

ing, if you notice any listed contents missing or evident damage. contact the store where you purchased the MX-80 F/T as soon as possible.

Power Cord (European Type)

MX-80 F/T Dot Matrix Printer

MX-80 F/T

1. Separator

Cartridge Ribbon

4. Power Cord (Only European Type 220/240V)

5. MX-80 F/T Operation Manual

Fig. 2 Contents of Carton

-2-

Operation Manual

1 1

]

2. Unpacking

Before removing the MX-80 F/T from the carton, check the box for evidence of shipping damage or mishandling. If such evidence is present, notify the carrier immediately.

2.1. Unpacking steps

Unpacking steps are as follows:

STEP 1. Open the carton.

STEP 2. Remove accessories. STEP 3. Remove the MX-80 F/T by holding its underside and lifting it straight

up with the packing material attached.

STEP 4. Place the Printer with the packing material on a table or any other con-

venient flat surface. STEP 5. Take off the packing material carefully. STEP 6. Remove the vinyl cover.

2.2. Repacking steps

Repacking can be carried out by following the above steps in the reverse order.

(Repacking: Shipment for repair, storage, etc.)

NOTE: It is recommended that all original packing materials be saved for reuse in case

the MX-80 F/T requires reshipment in the future.

3. Installation of the Printer

(1) Operating site selection

When installing the MX-80 F/T, observe the following instructions.

Place the Printer on a bench, tabletop or any other convenient flat sur-

(a)

face with enough room for the separator in the back of the Printer. NOTE: Rubber feet are provided to prevent the marring of the surface on

which the MX-80 F/T is placed.

Avoid operating the MX-80 F/T in places where it may be exposed to

(b)

direct sunlight or where a great deal of greasy dust exists in the air.

NOTE:

Connect the power cord to an outlet separated from those connected

(c)

to noise-generating equipment, such as large-power motors, refrigerators, etc. Do not subject the Printer to temperatures below 5°C

(d)

35°C (95’F) during operation, to sudden changes in temperature, or to extreme shock. Avoid use of the Printer in humid locations or in the vicinity of heat

(e)

generating sources such as heater, etc.

Greasy dust may cause the malfunction of the print head.

-3-

(4O’F)

or above

(2) Removal of protective paper for paper end detector

The MX-80 F/T is provided with a protective paper inserted between the

inner and outer paper guides to protect the paper end detector from

damage due to shocks or vibrations during transportation. Before using the

Printer, be sure to remove this paper. If the MX-80 F/T is to be reshipped. remember to return it to the original position.

(3) Removal of shipping screws

The purpose of the shipping screws is to protect the MX-80 F/T against any damage that may be caused by shocks or vibrations during transportation. Therefore, before operating the MX-80 F/T, remove the screws as de-

scribed below. (See Fig. 3.) STEP 1. Open the printer lid.

STEP 2. Remove with a screwdriver, the two shipping screws visible inside

the printer mechanism.

Shipping Screws

Fig. 3 Removal of Shipping Screws

NOTE: Save the two shipping screws for possible future use.

If the printer lid is an obstacle when removing the shipping screws, be sure to take off the printer lid by observing the following steps. Rough or careless handling of the printer lid may result in damage to. or even breakage of its hinges. Step 1. Stand the printer lid upright. Step 2. Push the printer lid toward the right and pull up its left side. (See

Figs. 4 (1) and (2).)

-4-

(1) Standard

Printer Lid

(2) Option

Fig. 4 Removal of Printer Lid

NOTE: The printer lid shown in Fig. 4 (2) is an optional accessory.

-5-

4. Cartridge Ribbon Setting

EPSON’s Cartridge Ribbon is compact, long-lasting, and very easy to set and remove. Furthermore, you have no need to soil your fingers in handling it. STEP 1. Open the printer lid (or remove it). STEP 2. Confirm that the scale (paper retainer) is turned toward the platen and

is touching.

STEP 3. Push the cartridge ribbon down and set it on the printer mechanism.

To facilitate the cartridge ribbon setting, be sure to hold the projection at the center of the cartridge case when pushing the cartridge ribbon down. (See Fig. 5.)

Fig. 5 Cartridge Ribbon

STEP 4. Put the ribbon between the head nose and the ribbon mask. In this

case, the ribbon can be set easily by hooking it to the edge of the head nose and turning the ribbon feeding knob of the cartridge case in the direction of the arrow (i.e., counterclockwise) while depressing the ribbon with a ball-point pen. Then, tension the ribbon by turning the ribbon feeding knob counterclockwise. (See Fig. 6.)

Fig. 6 Cartridge Ribbon Setting

-6-

NOTES: 1. Incorrect setting of the ribbon may cause it to come off. (See Fig. 7.)

2. Confirm that the ribbon is neither twisted nor creased and that the cartridge is set properly.

Ribbon Mask

Incorrect

Correct

Fig. 7 Examples of Correct and Incorrect Ribbon Setting

5. Separator Installation

The separator of the Printer contributes to smooth paper feeding. Set the sepa-

rator by inserting its edge into the two holes located at the rear part of the

paper feeding mechanism. (See Fig. 8.)

Fig. 8 Separator Installation

-7-

6. Dismounting of Tractor Unit

The tractor unit of the MX-80 F/T is detachable. If it is an obstacle when using

roll paper, it can be taken out as follows; STEP 1. Release the lock levers of the tractor unit by pulling in the direction as

shown in Fig. 9.

STEP 2. Keep pulling the levers and pull up the tractor unit

Lock lever

Fig. 9 Dismounting of Tractor Unit

To install the tractor unit, hook the notches of the tractor frames onto the shaft shown in Fig. 10 and then push down the tractor unit.

Fig. 10 Mounting of Tractor Unit

-8-

7. Paper Loading

7.1. Fanfold paper

7.1.1. Loading of fanfold paper The MX-80 F/T Printer accommodates fanfold paper from 4” to 10” in width. To load the fanfold paper, observe the following procedure.

STEP 1. Raise the printer lid.

STEP 2. Unlock the release lever by pulling it in the direction of the arrow. (See

Fig. 11.)

STEP 3. Pull the scale toward the front of the Printer to detach the scale from

the platen.

STEP 4. Confirm that the paper guide roller is at the center of the sprocket

shaft, If not, set it at the center of the shaft.

NOTE: The paper guide roller contributes to smooth paper feeding.

STEP 5 Raise the two paper holding covers, and be sure to insert the fanfold

paper between the frame and plastic roller of the separator. (See Fig.

11.)

Scale

Fig. 11

STEP 6. Push the paper into the insertion slot between the paper guides at the

rear part of the printer mechanism. NOTE: Be sure to pass the paper beneath the upper paper guide. Adjust the

position of the head adjusting lever in the forward (+) direction when inserting thicker paper. (See Section 8. Gap Adjustment.)

STEP 7. After the leading edge of the paper has emerged from the Printer, pull

it out gently to some length.

Insertion of Fanfold Paper

-9-

STEP 8. Raise the two sprocket lock levers to loosen, and adjust the sprocket

pin position to the paper width. (See Fig. 12.)

Paper Holding

Fig. 12

STEP 9. Engage the paper feed holes of the paper on the feeding pins, push the

Cover

ket Lock Lever

Raising of Sprocket Lock Levers

scale back into position, and adjust the tension of the paper. Then

push the paper holding covers and the two sprocket lock levers

down. (See Fig. 13.)

NOTE: In this case, confirm that the feeding pins are centered in the respec-

tive paper feed holes of the paper.

ocket Lock Lever

Fig. 13 Engagement of Paper Feed Holes on Feeding Pins

-10-

STEP 10. Put the printer lid on the Printer. (See Fig. 14.)

Fig. 14

Printer with Fanfold Paper Set Completely

NOTE: When the MX-80 F/T is to be used on a desk or a bench, arrangement

of the fanfold paper in parallel with the MX-80 F/T as shown below

will permit the paper to be folded in an accordion style.

Course of

Paper

Fig. 15: Example of Paper Arrangement

7.1.2. Removal of fanfold paper To remove the fanfold paper, follow either of the two methods described below.

(1) To disengage the paper from the paper holding mechanism, pull it forward

out of the Printer. NOTE: Do not attempt to pull out the paper in the backward direction.

(2) Feed the paper out of the Printer by electrical operation. For this, turn the

Power Switch on and push the Line Feed button. (Details are described later.1

-11-

7.1.3. Column layout on fanfold paper When fanfold paper of from 4” to 10” in width is supplied with the MX-80 F/T, the graduations on the scale can be used as the indexes of print column positions (1~80). Alignment of the print start position on fanfold paper with the

1st column position at the extreme left of the scale will facilitate column layout. Accordingly. center the paper by adjusting it to these indexes of the scale.

7.1.4. Top of form position setting The term “Top of Form position” is defined as the position in which the first print line lies on the form, and this position is determined when the power switch is turned on. Namely, adjust the paper position by the manual paper feed knob so that the required line position (i.e., the point at which the first line of the form is desired to be printed) is at the print head level. If, at this point,

power is applied to the Printer, this line position automatically becomes the

Top of Form position.

When printing forms, the matchmarks located on both the sprockets facilitate

the setting of the Top of Form position on the fanfold paper. To set the Top of

Form position, first enter (or preprint) a mark at a position on the edge of the paper 77 mm above the first print line position of the paper, then align this

mark with the matchmarks on the sprockets by turning the manual paper feed

knob. At this point, turn the Power Switch on and the Printer will recognize this position as the Top of Form position. Now, the printing can be started from the Top of Form position. (See Fig. 16.)

In case of feeding one page of fanfold paper by operating the MX-80 F/T by the

input of FF code, the abovementioned adjustment is effective.

Matchmark

77 mm

Fig. 16 Top of Form Position Setting

+ 41 hidden pages

Epson MX-80F, MX-80T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

INTRODUCTION

INSTALLATION