UB-P02II User's Manual
Copyright © 2000 by Seiko Epson Corporation, Nagano, Japan
Printed in China 2000.12
Introduction
This manual describes how to replace the interface board on TM series printers designed for the
UB-P02II.
You must check the printer settings after replacing the interface board. See the
documentation that came with the printer for information about the settings.
When you use the UB-P02II, note that you will not be able to use the display module (customer
display) connector of the printer.
About The Symbol In This Manual
CAUTION:
Cautions must be observed to avoid minor injury to yourself or damage to your
equipment.
Precautions
CAUTIONS:
●
Disconnect the power supply from the printer before you remove the interface
board; otherwise you may damage the interface board and the printer. You must
disconnect the power supply because the electrical current is flowing in some parts
of the printer circuit even when the power switch is turned off.
●
Wear a grounded wrist strap when handling the interface board to prevent damage from static electricity.
●
To avoid contamination, do not touch the board connector.
405162100
FCC Compliance Statement
For American Users
This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the
user will be required to correct the interference at his
own expense.
FOR CANADIAN USERS
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de Classe A est conforme à
la norme canadienne ICES-003.
EMC and Safety Standards Applied
Product Name: UB-P02II
Model Name:M112D
The following standards are also applied only to the
units that are so labeled. (EMC is tested using the
EPSON power suppliers and TM series printer.)
Europe: CE marking
North America: EMI: FCC/ICES-003 Class A
Japan: EMC: VCCI Class A
Oceania: EMC: AS/NZS 3548/CISPR22
Class B
WARNING
The connection of a non-shielded printer interface
cable to this board will invalidate the EMC standards
of this device. You are cautioned that changes or
modifications not expressly approved by SEIKO EPSON
Corporation could void your authority to operate the
equipment.
CE Marking
The board conforms to the following Directives and
Norms:
Directive 89/336/EEC
EN 55022 Class B
EN 55024
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-11
Unpacking
Make sure you have these items:
❏ UB-P02II
❏ This manual
Procedure
1 Removing the interface board from the printer
Remove the two screws that securing the interface board; then pull the board to
remove it. You will use the screws when installing the UB-P02II.
CAUTION:
Put the removed interface board into an anti-static bag for storage to
prevent damage from static electricity.
2 Installing the interface board enclosed in the package
Hold the UB-P02II as shown in the illustration below. Push the UB-P02II in gently
until you feel the connector fit into place.
3 Securing the UB-P02II
Secure the UB-P02II with the two screws.
4 Setting the printer settings
Change the printer settings to match the printer to the new interface.
See the parallel interface settings described in the printer documentation for the
settings.
Make sure you set the printer settings. Otherwise the printer may not work correctly.
Printed on Recycled Paper
Connector of
the UB-P02II
Connector of
the TM printer
Loading...