Epson GT-10000 Product Guide

EPSON GT-10000

Scanner Parts

carriage
(at home
position)

] Start button

transportation lock

terminator switch

SCSI ID dial

SCSI interfaces

ADF interface

Scanner Specifications

AC inlet

document cover

document table

control
panel

Scanning
resolution: 600 dpi main

2400 dpi sub with micro-step

Output
resolution: 50 to 4800 dpi (1-dpi increments)

Command level: ESC/I-B7

Color
separation: RGB color filters on CCD

Reading
sequence: Monochrome: 1-pass scanning

Color byte sequence: 1-pass scanning
(R, G, B)
Color line sequence: 1-pass scanning
(R, G, B)

Zoom: 50 to 200 percent in 1-percent increments

Image data: 36 bits input; 24 bits output (color)

12 bits input; 8 bits output (grayscale)

Brightness: 7 levels

Line art settings: Fixed threshold with Text Enhancement

Technology (TET) enabled

Halftoning
process: AAS (Auto Area Segmentation)

Enable/disable selectable
3 halftoning modes (A, B, and C)
4 dither patterns (A, B, C, and D) for
bi-level and quad-level
data (2 downloadable dither patterns)
2 user-defined dither patterns (A, B)

Gamma
correction: 2 types for CRT display

3 types for printer
1 user-defined table

Color
correction: 1 type for CRT display

3 types for printer output (available in
color byte sequence mode and color line
sequence mode)
1 type user-defined

Scanner type: Flatbed, color

Photoelectric
device: Color CCD line sensor

Effective pixels: 7020 dots

× 10200 pixels at 600 dpi,

100%

Document size: 11.7

× 17.0 inches (297 × 432 mm)

(the reading area can be specified from
your software)

Interface: SCSI II (two 50-pin high-density

connectors)

Options: Automatic Document Feeder (ADF)

Supported
documents: Opaque documents with smooth surfaces

Light source: Xenon fluorescent lamp

Reliability: Main unit MCBF: 100,000 cycles of

carriage movements

1/00 EPSON GT-10000

- 2

EPSON GT-10000

Noise: Under 50 db (operating)

Dimensions: Width: 25.8 inches (656 mm)

Depth: 18.0 inches (458 mm)
Height: 6.9 inches (176 mm)

Weight: Approximately 46.3 lb (21 kg)

Electrical

Input voltage
range: 100 to 120 VAC

220 to 240 VAC; universal auto-switching

Rated frequency: 50 to 60 Hz

Rated current: 100 to 120 VAC—1.2 A

220 to 240 VAC—0.7 A

Power
consumption: Operating

Approximately 50 W (approximately
55 W with the ADF

Check the label on the back of the scanner for
voltage information.

Environmental

Temperature: Operating

41 to 95 °F (5 to 35 °C)

Standby

–13 to 140 °F (–25 to 60 °C)

Humidity (without
condensation): Operating

10 to 80%

Standby

10 to 85%

Operating
conditions:

Ordinary office or home conditions; avoid
dust, direct sunlight, or strong light. Be sure
the outlet provides enough power.

230 V

Safety standards: EN 60950 (VDE)

EMC EN 55022 (CISPR Pub 22) class B

AS/NZS 3548 class B

CE marking

Low Voltage
Directive
73/23/EEC: EN60950

EMC Directive
89/336/EEC: EN 55022 Class B

EN 61000-3-2
EN 61000-3-3
EN 50082-1
IEC 801-2
IEC 801-3
IEC 801-4

SCSI Interface

Interface type: ANSI X3T9.2/375R Revision 10L

(SCSI II)

Functions: BUS FREE phase

ARBITRATION phase
SELECTION/RESELECTION phase
COMMAND phase
(the Logical Unit Number is fixed at 0 and
the Command Link Function
is not supported)
DATA phase

DATA IN phase

DATA OUT phase
STATUS phase
MESSAGE phase

MESSAGE IN phase

MESSAGE OUT phase
ATTENTION condition
RESET condition

Logic level: TTL compatible

Safety Approvals

120 V

Safety standards: UL 1950 with D3

CSA C22.2 No. 950 with D3
EMC FCC part 15 subpart B class B

(USA)
CSA C108.8 class B (Canada)

3 - EPSON GT-10000

Electrical standard: ANSI X3T9.2/375R Revision 10L

(SCSI II)

ID Setting: Selectable from 0 to 7 (factory setting: 2)

Terminator: Internal terminator selectable (enable/

disable)

1/00

EPSON GT-10000

25

1

Connector type: Two Micro DB-50 high-density

connectors

Connector pin arrangement:

50

26

Initialization methods

Scanner is turned on or receives a SCSI Reset signal from the
SCSI interface (hardware initialization).

Scanner receives a SCSI Bus Device message or an Esc @
command from the software (software initialization)

Optional Automatic Document Feeder (GT10000ADF)

The ADF allows you to automatically load multi-page
documents into your scanner.

General

Type: Page feeding and duplex scanning with

automatic reverse

Documents Supported

Document size: Portrait: A3, Ledger, B4, Legal, A4,

Letter, B5,

A5, 5.5 × 5.8 inch (140 × 148 mm)

Landscape: A4, Letter, B5, A5

2

Feeding capacity: 50 sheets of 21 lb (80 g/m

) paper: A4,
Letter
or smaller
30 sheets of 21 lb (80 g/m

2

) paper: B4,
Legal
or larger

Ejecting capacity: 100 sheets

Paper quality: High-quality bond paper

Compatible
paper types: High-quality paper, ink jet paper,

bond paper

2

Paper thickness: 13 to 33 lb (50 to 127 g/m

Don’t use the following paper types:
transparencies, tracing paper, coated paper
(such as photo quality and glossy paper), labels,
multipart forms, carbon paper, or paper with
staples, holes, rips, curls, or folds.

)

Electrical

Document
feeding: Pages are center aligned, fed face up from

bottom of stack, and ejected face up

Document
replacement time: 1.2 seconds (Letter/A4 landscape)

Multiple sizes: Unavailable; all documents in a stack must

be the same size

Noise: 50 dB or less

Reliability: 100,000 sheet paper feeding life

100,000 sheet paper ejecting life
100,000 hinge closings

Dimensions: Width: 23.6 inches (601 mm)

Depth: 20.8 inches (528 mm)
Height: 4.8 inches (122 mm)

Weight: 35.2 lb (16 kg)

Power supply: Supplied through the scanner

24 ± 10% VDC
5 ± 10% VDC

Consumption
current: 24 VDC: 2.0 A

5 VDC: 0.3 A

Insulation

resistance: 10 mΩ or more at 500 VDC

(between AC line and chassis)

Dielectric
strength: 1000 VAC per minute

(between AC line and chassis)

Resistance to
static electric noise: Case: Operated properly at 10 kV or less

Metal: Operated properly at 7 kV or less

1/00 EPSON GT-10000

- 4