Page 1
User's Guide
Page 2
Contents
2
Notations Used in This Guide 9
Using the Manual to Search for Information ................................ 10
Searching by Keyword................................................................................................................. 10
Jumping Directly from Bookmarks ......................................................................................... 10
Printing Only the Pages You Need ......................................................................................... 10
Getting the Latest Version of the Documents............................... 11
Introduction to Your Projector 12
Projector Parts and Functions ........................................................ 13
Projector Parts - Front/Top ........................................................................................................ 13
Projector Parts - Rear.................................................................................................................... 14
Projector Parts - Interface........................................................................................................... 15
Projector Parts - Base ................................................................................................................... 17
Installing the Safety Wire...................................................................................................... 17
Projector Parts - Control Panel................................................................................................. 18
Projector Parts - Remote Control ............................................................................................ 20
Installing Batteries in the Remote Control..................................................................... 23
Remote Control Operation .................................................................................................. 23
Locking the Remote Control Buttons .............................................................................. 24
Projector Parts - External Camera ........................................................................................... 24
Turning On the Projector ........................................................................................................... 37
Turning Off the Projector ........................................................................................................... 38
Wired Network Connection............................................................. 40
Connecting to a Wired Network.............................................................................................. 40
Selecting Wired Network Settings .......................................................................................... 40
Wireless Network Connection......................................................... 42
Installing the Wireless LAN Module ....................................................................................... 42
Selecting Wireless Network Settings Manually.................................................................. 43
Selecting Wireless Network Settings in Windows ............................................................ 44
Selecting Wireless Network Settings in Mac....................................................................... 44
Setting Up Wireless Network Security................................................................................... 44
Supported Client and CA Certificates.............................................................................. 46
Using a QR Code to Connect a Mobile Device................................................................... 46
Using a USB Key to Connect a Windows Computer ........................................................ 47
Secure HTTP...................................................................................... 48
Importing a Web Server Certificate Using the Menus..................................................... 48
Supported Web Server Certificates................................................................................... 48
Adjusting the Menu Settings 50
Home Screen..................................................................................... 51
Using the Projector's Menus ........................................................... 52
Setting Up the Projector 26
Notes on Transporting..................................................................... 27
Precautions on Installation ............................................................. 28
Attaching and Removing a Lens..................................................... 30
Attaching a Lens............................................................................................................................ 30
Removing a Lens ........................................................................................................................... 34
Attaching and Removing the Cable Cover .................................... 36
Operating the Projector Power ...................................................... 37
Using the Displayed Keyboard ....................................................... 53
Available Text Using the Displayed Keyboard ................................................................... 53
Using Basic Projector Features ....................................................... 54
Setting Up the Projector............................................................................................................. 54
Messages..................................................................................................................................... 54
Standby Confirmation............................................................................................................ 54
Sleep Mode ................................................................................................................................ 54
Beep.............................................................................................................................................. 54
Indicators .................................................................................................................................... 55
Date & Time ............................................................................................................................... 55
Page 3
Contents
3
Language.................................................................................................................................... 55
On-Screen Display ................................................................................................................... 55
Energy Saving Mode............................................................................................................... 55
Remote Control Type ............................................................................................................. 56
Projecting Images.......................................................................................................................... 56
Source Search............................................................................................................................ 56
A/V Mute ..................................................................................................................................... 56
Shutter ......................................................................................................................................... 57
Freeze........................................................................................................................................... 57
Split Screen ................................................................................................................................ 57
Volume......................................................................................................................................... 57
Aspect .......................................................................................................................................... 57
Screen Type ............................................................................................................................... 58
Projection.................................................................................................................................... 58
Test Pattern ................................................................................................................................ 58
Content Playback..................................................................................................................... 59
Display Background ................................................................................................................ 59
Startup Screen .......................................................................................................................... 59
Adjusting the Image Position and Shape ............................................................................ 59
Lens Shift .................................................................................................................................... 59
Zoom ............................................................................................................................................ 60
H/V-Keystone............................................................................................................................. 60
Quick Corner.............................................................................................................................. 60
Curved Surface.......................................................................................................................... 60
Corner Wall................................................................................................................................. 61
Point Correction ....................................................................................................................... 61
Adjusting the Image Quality ..................................................................................................... 61
Focus/Distortion ..................................................................................................................... 61
Color Mode ................................................................................................................................ 61
Image Enhancement .............................................................................................................. 62
Gamma ........................................................................................................................................ 62
RGBCMY....................................................................................................................................... 62
Brightness Settings ................................................................................................................. 62
Using Multiple Projectors........................................................................................................... 62
Tiling............................................................................................................................................. 63
Edge Blending........................................................................................................................... 63
Black Level .................................................................................................................................. 63
Scale.............................................................................................................................................. 63
Color Matching ......................................................................................................................... 64
Simple Stacking ........................................................................................................................ 64
Maintaining the Projector Quality........................................................................................... 64
Panel Alignment ...................................................................................................................... 65
Color Uniformity....................................................................................................................... 65
Refresh Mode ............................................................................................................................ 65
Light Source Calibration ....................................................................................................... 65
Managing the Projector's Settings.......................................................................................... 65
Memory ....................................................................................................................................... 65
Schedule Settings .................................................................................................................... 65
Button Lock................................................................................................................................ 66
Lens Lock .................................................................................................................................... 67
Password Protection............................................................................................................... 67
Copying Menu Settings Between Projectors (Batch Setup) ........ 68
Transferring Settings From a USB Flash Drive.................................................................... 68
Transferring Settings From a Computer............................................................................... 69
Batch Setup Error Notification.................................................................................................. 70
Menu Settings 71
Image Menu...................................................................................... 72
Color Mode ...................................................................................................................................... 72
Brightness......................................................................................................................................... 72
Contrast............................................................................................................................................. 73
Color Saturation ............................................................................................................................. 73
Tint ...................................................................................................................................................... 73
Sharpness ......................................................................................................................................... 73
White Balance ................................................................................................................................. 73
4K Enhancement............................................................................................................................ 73
Image Preset Mode....................................................................................................................... 74
Frame Interpolation...................................................................................................................... 74
Page 4
Contents
4
Deinterlacing................................................................................................................................... 74
Noise Reduction ............................................................................................................................. 75
MPEG Noise Reduction................................................................................................................ 75
Super-resolution ............................................................................................................................ 75
Detail Enhancement ..................................................................................................................... 75
Reset (Image Enhancement)..................................................................................................... 75
Scene Adaptive Gamma ............................................................................................................. 76
Gamma .............................................................................................................................................. 76
RGBCMY ............................................................................................................................................ 76
Dynamic Contrast.......................................................................................................................... 76
Lights-Out Control ........................................................................................................................ 77
Reset (Image menu) ..................................................................................................................... 77
Signal Menu...................................................................................... 78
Resolution......................................................................................................................................... 78
Aspect ................................................................................................................................................ 78
Tracking............................................................................................................................................. 79
Sync. ................................................................................................................................................... 79
Position.............................................................................................................................................. 79
Auto Setup ....................................................................................................................................... 79
Overscan ........................................................................................................................................... 80
Blanking ............................................................................................................................................ 80
Color Space ...................................................................................................................................... 80
Dynamic Range .............................................................................................................................. 80
Video Range .................................................................................................................................... 80
EDID.................................................................................................................................................... 81
Scale.................................................................................................................................................... 81
Reset (Signal menu)...................................................................................................................... 81
Settings Menu .................................................................................. 82
Geometry Correction ................................................................................................................... 82
Split Screen ...................................................................................................................................... 83
Split Screen Projection Restrictions .................................................................................. 83
Volume .............................................................................................................................................. 84
HDMI Link ......................................................................................................................................... 84
Control Panel Lock........................................................................................................................ 84
Lens Lock .......................................................................................................................................... 85
Light Source Mode........................................................................................................................ 85
Brightness Level ............................................................................................................................. 85
Constant Brightness ..................................................................................................................... 85
Estimated Remains........................................................................................................................ 86
Constant Brightness Usage Hours..................................................................................... 86
Light Source Operation Time.............................................................................................. 86
Energy Saving Mode .................................................................................................................... 87
Remote Receiver ............................................................................................................................ 87
User Button ...................................................................................................................................... 88
Test Pattern...................................................................................................................................... 88
Memory ............................................................................................................................................. 88
Content Playback........................................................................................................................... 89
Creating Playlists Using Epson Web Control................................................................. 89
Supported Content Playback Mode File Types............................................................ 90
Content Playback Mode Restrictions ............................................................................... 91
NFC Settings .................................................................................................................................... 91
Reset (Settings menu).................................................................................................................. 91
Extended Menu ................................................................................ 93
Home Screen ................................................................................................................................... 93
Menu Position................................................................................................................................. 93
Message Position ........................................................................................................................... 94
Messages .......................................................................................................................................... 94
Display Background...................................................................................................................... 94
Startup Screen ................................................................................................................................ 94
Standby Confirmation ................................................................................................................. 94
Screen ................................................................................................................................................ 94
Panel Alignment ............................................................................................................................ 95
Color Uniformity ............................................................................................................................ 95
OSD Rotation................................................................................................................................... 95
User's Logo....................................................................................................................................... 96
Projection ......................................................................................................................................... 96
Direct Power On............................................................................................................................. 96
Sleep Mode ...................................................................................................................................... 96
Page 5
Contents
5
Sleep Mode Timer ......................................................................................................................... 96
High Altitude Mode...................................................................................................................... 96
Auto Source Search ...................................................................................................................... 97
Auto Power On............................................................................................................................... 97
Startup Source ................................................................................................................................ 97
Quick Startup .................................................................................................................................. 97
USB Power ........................................................................................................................................ 97
A/V Mute Settings ......................................................................................................................... 97
Shutter Settings ............................................................................................................................. 98
Remote Control Type................................................................................................................... 98
Beep.................................................................................................................................................... 98
Indicators.......................................................................................................................................... 98
Log Save Destination ................................................................................................................... 99
Batch Setup Range........................................................................................................................ 99
AC Voltage Monitoring................................................................................................................ 99
Lens Type.......................................................................................................................................... 99
Date & Time..................................................................................................................................... 99
Lens Calibration ........................................................................................................................... 100
A/V Settings................................................................................................................................... 100
Standby Mode .............................................................................................................................. 100
HDBaseT ......................................................................................................................................... 100
Color Calibration ......................................................................................................................... 101
Conditions for Color Calibration...................................................................................... 101
Projector ID.................................................................................................................................... 101
Projector Grouping..................................................................................................................... 101
Tiling ................................................................................................................................................ 101
Edge Blending .............................................................................................................................. 102
Black Level ..................................................................................................................................... 102
Reset (Multi-Projection menu)............................................................................................... 103
Screen Matching ......................................................................................................................... 103
Conditions for Screen Matching...................................................................................... 103
Color Matching ............................................................................................................................ 104
Simple Stacking ........................................................................................................................... 104
Conditions for Simple Stacking ....................................................................................... 105
Schedule Settings ....................................................................................................................... 105
Schedule Status Icons.......................................................................................................... 105
Language ....................................................................................................................................... 106
Reset (Extended menu) ............................................................................................................ 106
Network Menu................................................................................ 107
Wireless Mode .............................................................................................................................. 107
Net. Info. - Wireless LAN........................................................................................................... 107
Net. Info. - Wired LAN................................................................................................................ 108
Display the QR Code .................................................................................................................. 108
Remote Camera Access ............................................................................................................ 108
Projector Name ............................................................................................................................ 108
PJLink Password .......................................................................................................................... 108
Remote Password ....................................................................................................................... 108
Web Control Password ............................................................................................................. 108
Moderator Password.................................................................................................................. 109
Projector Keyword ...................................................................................................................... 109
Display Keyword.......................................................................................................................... 109
Display LAN Info.......................................................................................................................... 109
Connection Mode ....................................................................................................................... 109
Search Access Point ................................................................................................................... 109
SSID .................................................................................................................................................. 110
Security ........................................................................................................................................... 110
Passphrase ..................................................................................................................................... 110
EAP Method .................................................................................................................................. 111
Channel........................................................................................................................................... 111
IP Settings ...................................................................................................................................... 111
SSID Display .................................................................................................................................. 112
IP Address Display ...................................................................................................................... 112
IPv6 Settings ................................................................................................................................. 112
Mail Notification .......................................................................................................................... 112
Network Projector E-mail Alert Messages.................................................................... 112
SMTP Server .................................................................................................................................. 113
Port Number ................................................................................................................................. 113
From................................................................................................................................................. 113
Address 1 Setting/Address 2 Setting/Address 3 Setting ............................................. 113
Page 6
Contents
6
SNMP ............................................................................................................................................... 113
Trap IP Address 1/Trap IP Address 2.................................................................................... 113
Community Name ...................................................................................................................... 114
PJLink Notification ...................................................................................................................... 114
Notified IP Address..................................................................................................................... 114
Command Communication..................................................................................................... 114
Secure HTTP .................................................................................................................................. 114
Web Server Certificate............................................................................................................... 114
Web API Settings......................................................................................................................... 114
Priority Gateway .......................................................................................................................... 115
PJLink............................................................................................................................................... 115
AMX Device Discovery .............................................................................................................. 115
Crestron Connected ................................................................................................................... 115
Art-Net............................................................................................................................................. 115
Message Broadcasting .............................................................................................................. 115
Reset (Network menu) .............................................................................................................. 116
Info Menu........................................................................................ 117
Projector Info ................................................................................................................................ 117
Event ID Code List................................................................................................................. 117
Light Source Info......................................................................................................................... 118
Version ............................................................................................................................................ 118
Status Information ...................................................................................................................... 118
Voltage Warning Info ................................................................................................................ 119
Temp Warning Info .................................................................................................................... 119
Power On/Off History ................................................................................................................ 119
Reset Menu ..................................................................................... 120
Reset All Memories..................................................................................................................... 120
Refresh Mode................................................................................................................................ 120
Light Source Calibration........................................................................................................... 120
Reset All Config............................................................................................................................ 121
Reset All (Factory Default) ....................................................................................................... 121
Adjusting Projector Features 123
Multi-Projection Features ............................................................. 124
Procedure Overview .................................................................................................................. 124
Preparing for Multi-Projection ............................................................................................... 124
Initializing Projectors ........................................................................................................... 124
Assigning a Master Projector............................................................................................ 125
Calibrating Projectors .......................................................................................................... 125
Installing Projectors.............................................................................................................. 125
Performing Rough Image Adjustments........................................................................ 125
Connecting Projectors to a Network ............................................................................. 126
Image Composition.................................................................................................................... 126
Tiling Using the Epson Projector Professional Tool Software .............................. 126
Tiling Using the Projector's Menu................................................................................... 127
Stacking Using the Epson Projector Professional Tool Software........................ 131
Stacking Using the Projector's Menu............................................................................. 131
Adjusting Colors .......................................................................................................................... 132
External Camera Usage ................................................................. 133
Monitoring and Controlling the Projector 134
Projector Monitoring and Control Options................................. 135
Epson Projector Management ............................................................................................... 135
Epson Web Control .................................................................................................................... 135
SNMP ............................................................................................................................................... 135
ESC/VP21 Commands .............................................................................................................. 135
ESC/VP.net Commands ............................................................................................................. 136
PJLink............................................................................................................................................... 136
Art-Net............................................................................................................................................. 136
Crestron Connected Support ................................................................................................. 136
Web API .......................................................................................................................................... 137
Accessing a Networked Projector Using a Web Browser........... 138
Web Control Options................................................................................................................. 139
Page 7
Contents
7
Maintaining the Projector 149
Projector Maintenance .................................................................. 150
Cleaning the Lens........................................................................... 151
Cleaning the Projector Case.......................................................... 152
Cleaning the Air Intake Vents ...................................................... 153
Solving Problems 154
Projection Problems ...................................................................... 155
Projector Indicator Status ............................................................. 156
Projector Status Display Messages .............................................. 159
Solving Image or Sound Problems............................................... 164
Solutions When No Image Appears..................................................................................... 164
Solutions When "No Signal" Message Appears ............................................................... 164
Displaying From a Windows Laptop.............................................................................. 165
Displaying From a Mac Laptop........................................................................................ 165
Solutions When "Not Supported" Message Appears .................................................... 165
Solutions When Only a Partial Image Appears................................................................ 165
Solutions When the Image is not Rectangular................................................................ 166
Solutions When the Image Contains Noise or Static..................................................... 166
Solutions When the Image is Fuzzy or Blurry .................................................................. 166
Solutions When the Image Brightness or Colors are Incorrect ................................. 167
Solutions When Automatic Adjustments are not Applied Correctly ...................... 167
Solutions When Simple Stacking is not Applied Correctly ......................................... 168
Solutions When an Afterimage Remains on the Projected Image .......................... 168
Solutions to Sound Problems................................................................................................. 168
Solving Projector or Remote Control Operation Problems....... 170
Solutions to Projector Power or Shut-Off Problems...................................................... 170
Solutions to Problems with the Remote Control............................................................ 170
Solutions to Password Problems........................................................................................... 171
Solution When "The Battery that Saves Your Clock Settings is Running Low"
Message Appears ........................................................................................................................ 171
Solutions to Problems in Content Playback Mode ..................... 172
Solving Network Problems ........................................................... 173
Solutions When Wireless Authentication Fails ................................................................ 173
Solutions When You Cannot Access the Projector Through the Web ................... 173
Solutions When Network Alert E-Mails are not Received............................................ 173
Solutions When the Image Contains Static During Network Projection............... 174
Solutions When You Cannot Monitor and Control the Projector over a
Network .......................................................................................................................................... 174
Appendix 175
Optional Accessories and Replacement Parts............................. 176
Lens .................................................................................................................................................. 176
Mounts............................................................................................................................................ 176
External Devices .......................................................................................................................... 176
For Wireless Connection .......................................................................................................... 176
Screen Size and Projection Distance............................................ 177
Projection Distance Formula .................................................................................................. 177
Projection Distance .................................................................................................................... 179
Projector Specifications................................................................. 184
Supported Features for Epson Projector Content Manager...... 186
List of Safety Symbols and Instructions ...................................... 187
Laser Safety Information............................................................... 189
Laser Warning Labels................................................................................................................. 189
Hazard Distance according to IEC62471-5 .................................. 191
Notices ............................................................................................ 192
FCC Compliance Statement.................................................................................................... 192
Indication of the manufacturer and the importer in accordance with
requirements of EU directive.................................................................................................. 193
Page 8
Contents
Indication of the manufacturer and the importer in accordance with
requirements of United Kingdom directive...................................................................... 193
Restriction of Use........................................................................................................................ 193
Operating System References................................................................................................ 193
Trademarks.................................................................................................................................... 193
Copyright Notice ......................................................................................................................... 194
Copyright Attribution................................................................................................................ 194
8
Page 9
Notations Used in This Guide
Safety Symbols
The projector and its manuals use graphical symbols and labels to indicate content that tells you how to use the projector safely.
Read and carefully follow the instructions that are marked with these symbols and labels to avoid injury to persons or damage to property.
This symbol indicates information that, if ignored, could possibly result in personal injury or even death.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
Caution
General Information Notations
This label indicates procedures that may result in damage or injury if sufficient care is not taken.
Attention
This label indicates additional information that may be useful to know.
[Button name] Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Menu/Setting name Indicates projector menu and setting names.
Example:
Select the Image menu
This label indicates links to the related pages.
s
This label indicates the projector's current menu level.
gg Related Links
• "Using the Manual to Search for Information" p.10
• "Getting the Latest Version of the Documents" p.11
Page 10
Using the Manual to Search for Information
10
We assume that this manual will be used by specialists with technical
knowledge and experience of projector installation and adjustment.
Make sure you read the Safety Instructions before using your projector.
The PDF manual allows you to search for information you are looking for by
keyword, or jump directly to specific sections using the bookmarks. You can
also print only the pages you need. This section explains how to use a PDF
manual that has been opened in Adobe Reader X on your computer.
gg Related Links
• "Searching by Keyword" p.10
• "Jumping Directly from Bookmarks" p.10
• "Printing Only the Pages You Need" p.10
Searching by Keyword
Click Edit > Advanced Search. Enter the keyword (text) for information you
want to find in the search window, and then click Search. Hits are displayed
as a list. Click one of the displayed hits to jump to that page.
• Mac OS: Hold down the command key, and then press ←.
Printing Only the Pages You Need
You can extract and print only the pages you need. Click Print in the File
menu, and then specify the pages you want to print in Pages in Pages to
Print.
• To specify a series of pages, enter a hyphen between the start page and the
end page.
Example: 20-25
• To specify pages that are not in series, divide the pages with commas.
Example: 5, 10, 15
Jumping Directly from Bookmarks
Click a title to jump to that page. Click + or > to view the lower level titles in
that section. To return to the previous page, perform the following operation
on your keyboard.
• Windows: Hold down Alt, and then press ←.
Page 11
Getting the Latest Version of the Documents
You can get the latest version of the manuals and specifications on the Epson
Web site.
Visit epson.sn, and enter your model name.
11
Page 12
Introduction to Your Projector
See these sections to learn more about your projector.
gg Related Links
• "Projector Parts and Functions" p.13
Page 13
Projector Parts and Functions
13
The following sections explain the projector parts and their functions.
gg Related Links
• "Projector Parts - Front/Top" p.13
• "Projector Parts - Rear" p.14
• "Projector Parts - Interface" p.15
• "Projector Parts - Base" p.17
• "Projector Parts - Control Panel" p.18
• "Projector Parts - Remote Control" p.20
• "Projector Parts - External Camera" p.24
Projector Parts - Front/Top
Name Function
External camera cover Open this cover to install the optional external camera.
A
When using the ultra short-throw zoom lens, install the
optional external camera on the lens.
Air intake vent Takes in air to cool the projector internally.
B
Remote receivers Receive signals from the remote control.
C
Lens Images are projected from here.
D
Warning
Do not look into the projection lens while
projecting.
Caution
Do not place any objects or put your hand near
the projection lens. It could cause burns, fire,
or the object to warp because this area reaches
a high temperature due to the concentrated
projection light.
Air exhaust vent Exhaust vent for air used to cool the projector
E
internally.
Caution
While projecting, do not put your face or
hands near the air exhaust vent, and do not
place objects that may become warped or
damaged by heat near the vent. Hot air from
the air exhaust vent could cause burns,
warping, or accidents to occur.
Cable cover Cover for the rear interface ports section.
F
Indicator lights Indicate the projector's status.
G
Page 14
Projector Parts and Functions
14
Name Function
NFC tag Uses NFC technology to transfer projector information
H
Lens replacement
I
cover
through your mobile device.
The Projector Config Tool app lets you scan projector
information and write settings.
You can download the Projector Config Tool app for
free from the App Store or Google Play. Any fees
incurred when communicating with the App Store or
Google Play are the responsibility of the customer.
Remove when attaching or removing the lens.
gg Related Links
• "Projector Indicator Status" p.156
• "Attaching and Removing the Cable Cover" p.36
• "Attaching and Removing a Lens" p.30
Projector Parts - Rear
Name Function
Control panel Operates the projector.
B
Connector ports Connects interface cables.
C
Security slot The security slot is compatible with the Microsaver
D
Cable holder Pass a commercially available cable tie through here to
E
Security System manufactured by Kensington.
For more details on the Microsaver Security System,
visit the Kensington Web site.
https://www.kensington.com/
secure cables.
Warning
Do not bundle the power cord to the other
cables. Otherwise, a fire may occur.
Power inlet Connects the power cord to the projector.
F
Cable lock Secures the power cord to prevent it from falling off.
G
Wireless LAN module
H
cover
gg Related Links
• "Installing the Wireless LAN Module" p.42
Open this cover to install the wireless LAN module.
Name Function
Air intake vent Takes in air to cool the projector internally.
A
Page 15
Projector Parts and Functions
15
Projector Parts - Interface
Attention
• Check the shape and orientation of the connectors on any cable you plan to
connect. Do not force a connector into a port if it does not fit. The device or
your projector could be damaged or could malfunction.
• Do not turn on the input source before connecting it to the projector. Doing so
could damage the projector.
• If necessary, use an adapter that allows you to connect to an input port on the
projector.
Name Function
Computer port
A
(Mini D-Sub15-pin,
female)
Inputs image signals from a computer.
Name Function
Audio Out port
B
(Stereo mini pin jack)
RS-232C port
C
(Mini D-Sub 9-pin,
male)
Remote port
D
(Stereo mini pin jack)
SDI Out/In ports
E
(BNC)
Outputs audio from the current input source to an
external speaker. You can also connect the projector to
an amplifier with speakers.
To output audio from the speaker connected to this
port, select Projector as the Audio Out Device setting
in the projector's Settings menu. When an audio/video
system is not connected to the projector, audio is
output from the speaker connected to this port even if
Audio Out Device is set to AV System.
s Settings > HDMI Link > Audio Out Device
If you want to output audio for the HDMI source from
the external speakers when the projector is turned off,
select Always On as the A/V Output setting in the
projector's Extended menu.
s Extended > A/V Settings > A/V Output
Use to connect an RS-232C cable to control the
projector from a computer.
Connects the remote control to the projector using a
commercially available 3.5 mm stereo mini-jack audio
cable and inputs signals from the remote control.
When the remote control is connected, the remote
receiver on the projector is disabled.
(EB‑PU2220B only)
Inputs video signals from SDI compatible video
equipment.
Outputs video signals input from the SDI In port to an
external monitor.
You can connect two projectors in a chain using a SDI
cable.
If you want to output images to an external monitor
when the projector is turned off, select Always On as
the A/V Output setting in the projector's Extended
menu.
s Extended > A/V Settings > A/V Output
Page 16
Projector Parts and Functions
16
Name Function
USB-A port
F
(USB connector Type
A)
Use to connect a USB memory device for projecting
movies or images in Content Playback mode. It is also
used for batch settings and firmware update.
Use to connect the optional camera when using the
optional ultra short-throw zoom lens.
Provides a connection for a streaming media player to
power it.
Attention
• Use the USB cable supplied with or specified
• Do not connect a USB hub or a USB cable
Service port
G
(USB connector Type
B)
HDMI port
H
(HDMI)
DVI-D port
I
(DVI-D 24-pin
single)
This port is used for batch settings and firmware
update.
Inputs video signals from HDMI compatible video
equipment and computers.
Connects the optional base unit of the Epson Wireless
Presentation System.
This port is compatible with HDCP2.3. (Audio is only
supported by PCM)
Inputs the computer DVI-D signals.
This port is compatible with HDCP1.4.
for use with the device.
longer than 3 meters, or the device may not
operate correctly.
Name Function
HDBaseT port
J
(RJ-45)
LAN port
K
(RJ-45)
Use to connect a LAN cable to the optional HDBaseT
Transmitter. You can use a network cable up to 100 m
in length. To ensure proper data transmission, use a
Category 5e STP cable or better. However, operation is
not guaranteed for all input/output devices and
environments.
This port is compatible with HDCP2.3.
Check the following settings:
• To enable communication from the Ethernet and
serial ports on the transmitter, select On as the
Control Communications setting in the projector's
Extended menu.
s Extended > HDBaseT > Control
Communications
• If you have connected an Extron XTP transmitter or
switcher, select On as the Extron XTP setting in the
projector's Extended menu.
s Extended > HDBaseT > Extron XTP
Use to connect a LAN cable to connect to a network.
Use a 100Base-TX or 10Base-T network cable.
To ensure proper data transmission, use a Category 5
shielded cable or better.
Page 17
Projector Parts and Functions
17
Projector Parts - Base
Name Function
Rear feet When the projector is set up on a surface such as a
C
Screw holes (for the
D
cable cover)
Air intake vent Takes in air to cool the projector internally.
E
Security cable
F
attachment point
Ceiling mount fixing
G
points (ELPMB67, 4
points)
desk, turn to extend and retract the feet to adjust the
horizontal tilt.
You can adjust the tilt within a range of ±5°. The rear
feet are detachable. You can extend the feet by
approximately 35 mm before they detach.
The screw holes for securing the cable cover.
Make sure the cables have been passed through the
notch on the base of the cable cover before attaching
the cable cover.
Pass the theft-prevention wire lock through here and
lock it in place.
Use these points to attach the optional ceiling mount
when installing the projector on a wall, or mounting
the projector from a ceiling.
gg Related Links
• "Installing the Safety Wire" p.17
Installing the Safety Wire
Name Function
Front feet When the projector is set up on a surface such as a
A
Screw hole (for the
B
ring of the safety
wire)
desk, turn to extend and retract the feet to adjust the
horizontal tilt.
You can adjust the tilt within a range of ±5°. The front
feet are detachable. You can extend the feet by
approximately 35 mm before they detach.
Screw hole for securing the ring of the safety wire to
prevent the projector from falling from the ceiling or
wall.
When you use the optional ceiling mount, you can install the safety wire to
prevent the projector from falling from the ceiling.
Page 18
Projector Parts and Functions
18
Secure the ring using the M6 × 15 mm bolt supplied with the safety wire set,
and loop the safety wire through the ceiling mount to secure it as shown.
Projector Parts - Control Panel
Name Function
[On] button Turns the projector on.
A
[Source Search]
B
button
[Menu] button Displays and closes the projector's menu.
C
[Enter] button [ ] Enters the current selection and moves to the next level
D
Control panel lock
E
button and arrow
button
Test pattern button
F
and arrow button
Changes to the next input source.
while displaying the projector's menu.
When projecting an analog RGB signal from the
Computer port, optimizes the Tracking, Sync., and
Position settings in the projector's Signal menu.
Displays the Control Panel Lock screen allowing you
to lock the control panel buttons.
Do one of the following to unlock them.
• Set the Control Panel Lock setting to Off.
s Settings > Lock Setting > Control Panel Lock
• Hold down the [Enter] button on the control panel
for more than 7 seconds.
Selects menu items while displaying the projector's
menu.
Displays a test pattern. The test pattern's shape is
determined by the Screen Type setting. Be sure to set
the correct screen type before adjusting with the test
pattern.
s Extended > Display > Screen > Screen Type
Selects menu items while displaying the projector's
menu.
Page 19
Projector Parts and Functions
19
Name Function
[A/V Mute] button EB‑‑PU2220B:
G
Turns the video and audio on or off temporarily by
opening/closing the mechanical shutter.
The projector's power automatically turns off two
hours after the shutter function is enabled. You can
disable this feature.
s Extended > Operation > Shutter Settings >
Shutter Timer
EB‑‑PU2120W:
Turns the video and audio on or off temporarily.
The projector's power automatically turns off two
hours after A/V Mute is enabled. You can disable this
feature.
s Extended > Operation > A/V Mute Settings >
A/V Mute Timer
[Lens] button Displays the adjustment screens for lens shift, zoom,
H
Information button
I
[ ] and arrow button
Geometry correction
J
button and arrow
button
focus, and distortion in that order each time the button
is pressed. Wait 20 minutes after turning on the
projector before setting the focus, zoom, and lens shift
for maximum accuracy.
When adjusting the image position using vertical lens
shift, adjust it by moving the image from the bottom to
the top. If you adjust it from the top to the bottom, the
image position may move down slightly after adjusting.
Hold down this button for more than 3 seconds to
move the lens position to the home position. Keep the
lens position in the home position for the clearest
picture.
Displays the projector's Info menu.
Selects menu items while displaying the projector's
menu.
Corrects the shape of the image using the options in
the Geometry Correction setting.
Selects menu items while displaying the projector's
menu.
Name Function
[Esc] button Stops the current function.
K
Moves back to the previous menu level while
displaying the projector's menu.
[Standby] button Turns the projector off.
L
gg Related Links
• "Button Lock" p.66
• "Test Pattern" p.58
• "A/V Mute" p.56
• "Shutter" p.57
• "Geometry Correction" p.82
Page 20
Projector Parts and Functions
20
Projector Parts - Remote Control
Name Function
[On] button Turns the projector on.
A
[Standby] button Turns the projector off.
B
Name Function
Switch image source
C
buttons
[Aspect] button Changes the aspect mode.
D
[Auto] button When projecting an analog RGB signal from the
E
[Freeze] button Pauses or resumes images. Any sound or video action
F
[Test Pattern] button Displays a test pattern. The test pattern's shape is
G
[Lens Shift] button Adjusts the position of the projected image. Wait 20
H
[Zoom] button Adjusts the image size.
I
Switch the image source to each port.
You cannot change the aspect mode when the current
source is LAN.
Note that using the aspect ratio function of the
projector to reduce, enlarge, or split the projected
image for commercial purposes or for public viewing
may infringe upon the rights of the copyright holder of
that image based on copyright law.
Computer port, optimizes the Tracking, Sync., and
Position settings in the projector's Signal menu.
continues to run, however, so you cannot resume
projection at the point that you stopped it.
Hold down this button for more than 5 seconds to set
up password security.
determined by the Screen Type setting. Be sure to set
the correct screen type before adjusting with the test
pattern.
s Extended > Display > Screen > Screen Type
minutes after turning on the projector before setting
the focus, zoom, and lens shift for maximum accuracy.
When adjusting the image position using vertical lens
shift, adjust it by moving the image from the bottom to
the top. If you adjust it from the top to the bottom, the
image position may move down slightly after adjusting.
Hold down this button for more than 3 seconds to
move the lens position to the home position. Keep the
lens position in the home position for the clearest
picture.
Page 21
Projector Parts and Functions
21
Name Function
[Menu] button Displays and closes the projector's menu.
J
Hold down this button for more than 15 seconds to
turn on all remote receivers.
Arrow buttons Selects menu items while displaying the projector's
K
[Enter] button [ ] Enters the current selection and moves to the next level
L
[A/V Mute] button EB‑‑PU2220B:
M
[Page] up/down
N
buttons
menu.
while displaying the projector's menu.
Turns the video and audio on or off temporarily by
opening/closing the mechanical shutter.
The projector's power automatically turns off two
hours after the shutter function is enabled. You can
disable this feature.
s Extended > Operation > Shutter Settings >
Shutter Timer
Hold down this button for more than 5 seconds to flip
the image over top-to-bottom.
EB‑‑PU2120W:
Turns the video and audio on or off temporarily.
The projector's power automatically turns off two
hours after A/V Mute is enabled. You can disable this
feature.
s Extended > Operation > A/V Mute Settings >
A/V Mute Timer
Hold down this button for more than 5 seconds to flip
the image over top-to-bottom.
Display the previous or next test pattern while
displaying a test pattern.
Controls page up and down on your computer when
you connect a projector and computer over the
network.
Name Function
[Volume] up/down
O
buttons
Adjusts the volume of the speaker connected to the
projector's Audio Out port.
Caution
Do not start a presentation at a high volume
setting. Sudden loud noises may cause hearing
loss.
Always lower the volume before powering off,
so that you can power on and then gradually
increase the volume.
Information button
P
[ ]
[User] buttons Perform settings assigned in the User Button setting in
Q
Numeric buttons Enters numbers in the projector's menu while holding
R
[ID] button Press this button and press a number button within 5
S
[ID] switch Enables (On) or disables (Off) ID settings for the
T
Remote port Connects the remote control to the projector using a
U
Displays the projector's Info menu.
the projector's Settings menu.
down the [Num] button.
In Content Playback mode, enter numbers while
holding down the [Num] button to play back your
favorite playlists.
seconds to select the ID for the projector you want to
operate using the remote control. (Enter a one-digit or
two-digit number.)
If you do not know the projector's ID, press this button
during projection to temporarily display the projector's
ID and the remote control's ID on the screen.
remote control.
commercially available 3.5 mm stereo mini-jack audio
cable and inputs signals from the remote control.
When the remote control is connected, the remote
receiver on the projector is disabled.
Page 22
Projector Parts and Functions
22
Name Function
[Home] button Displays and closes the Home screen.
V
Hold down this button for more than 5 seconds to lock
or unlock the remote control buttons.
[Num] button Hold down this button to enter numbers using the
W
[Geometry] button Displays the Geometry Correction screen allowing you
X
[Memory] button Displays the Memory screen where you can save
Y
[E-Zoom] +/–
Z
buttons
[Default] button Returns the selected setting to its default value.
a
[Esc] button Stops the current function.
b
[Focus] button Displays the screen where you can adjust the focus and
c
numeric buttons.
to correct keystone distortion of the projected image.
customized settings and load saved settings. A memory
name that has already been used is indicated by a blue
mark. Saving over a previously saved memory
overwrites the settings with your current settings.
Resizes the projected image without changing the
projection size.
This feature is unavailable if the Scale setting is enabled
in the projector's menu.
s Signal > Scale
s Extended > Multi-Projection > Scale
Hold down this button for more than 3 seconds to start
the lens calibration process.
Moves back to the previous menu level while
displaying the projector's menu.
distortion in the projected image.
Name Function
[Split] button Projects two images from different image sources
d
[Color Mode] button Changes the color mode.
e
[Search] button Switches to the next input source.
f
Illumination button
g
[ ]
Indicator A light is emitted when outputting remote control
h
Remote control light
i
emitting area
simultaneously by splitting the projected screen.
While using the split screen feature, other projector
features may not be available and some settings may be
automatically applied to all images.
You cannot perform split screen projection when the
Content Playback setting is set to On in the projector's
Settings menu.
Some input source combinations are not supported for
split screen projection.
Illuminates the buttons on the remote control for
approximately 15 seconds. This is useful when using
the remote control in the dark.
signals.
Outputs remote control signals.
gg Related Links
• "Installing Batteries in the Remote Control" p.23
• "Remote Control Operation" p.23
• "Locking the Remote Control Buttons" p.24
• "Password Protection" p.67
• "Test Pattern" p.58
• "A/V Mute" p.56
• "Shutter" p.57
• "Home Screen" p.51
• "Geometry Correction" p.82
• "Memory" p.88
• "Split Screen" p.83
Page 23
Projector Parts and Functions
23
Installing Batteries in the Remote Control
The remote control uses the two AA batteries that came with the projector.
Attention
Make sure you read the Safety Instructions before handling the batteries.
Replace the batteries as soon as they run out. The remote control uses
a
a
two AA manganese or alkaline batteries.
Remove the battery cover as shown.
Warning
Check the positions of the (+) and (–) marks inside the battery holder to
ensure the batteries are inserted the correct way. If the batteries are not used
correctly, they could explode or leak causing a fire, injury, or damage to the
product.
Replace the battery cover and press it down until it clicks into place.
d
Remote Control Operation
The remote control lets you control the projector from almost anywhere in
the room.
Make sure that you aim the remote control at the projector's receivers within
the distance and angles listed here.
Remove the old batteries, if necessary.
b
Dispose of used batteries according to local regulations.
a
Insert the batteries.
c
Page 24
Projector Parts and Functions
24
• Depending on your installation environment, the available distance
a
and angles may be shortened.
• Avoid using the remote control in conditions with bright fluorescent
lights or in direct sunlight, or the projector may not respond to
commands. If you are not going to use the remote control for a long
time, remove the batteries.
• When you use multiple projectors in the same room or when there
are obstacles around the remote receiver, connect the remote control
to the projector using a commercially available 3.5 mm stereo minijack audio cable. When the remote control is connected, the remote
receiver on the projector is disabled.
Locking the Remote Control Buttons
You can lock some of the buttons on the remote control.
To lock the remote control buttons shown here, press and hold the [Home]
button on the remote control for approximately 5 seconds.
To unlock the buttons, press and hold the [Home] button again for
approximately 5 seconds.
Projector Parts - External Camera
You can attach the optional external camera to the front of the projector or
lens. See the external camera manual for the installation method.
You can acquire the manual for the external camera from the following Epson
Web site.
Page 25
Projector Parts and Functions
25
https://epson.sn/?MKN=EB-PU2220B&PINF=vpoption
Name Function
Camera lens Takes photos.
A
Name Function
micro USB-B port Connects the supplied USB cable to the projector.
C
Screw holes (for
D
installation)
Secures the mount for installing the external camera.
gg Related Links
• "External Camera Usage" p.133
Attention
Do not use or store the external camera in
places where it will be exposed to strong light.
Otherwise, burning or malfunction may occur.
Indicator light Indicates the external camera's status.
B
• Lit: standby
• Flashing (0.25 seconds intervals): external camera is
malfunctioning
• Flashing (0.5 seconds intervals): external camera is
operating
• Flashing (1 second intervals): updating the firmware
Page 26
Setting Up the Projector
Follow the instructions in these sections to set up your projector.
gg Related Links
• "Notes on Transporting" p.27
• "Precautions on Installation" p.28
• "Attaching and Removing a Lens" p.30
• "Attaching and Removing the Cable Cover" p.36
• "Operating the Projector Power" p.37
• "Wired Network Connection" p.40
• "Wireless Network Connection" p.42
• "Secure HTTP" p.48
Page 27
Notes on Transporting
There are many glass parts and precision components inside the projector. To
prevent damage due to impacts when transporting, handle the projector as
follows.
Caution
• The projector should not be carried by one person. At least two people are
needed to unpack or carry the projector.
• When moving the projector, do not hold the lens replacement cover or lens unit.
They may become disconnected and the projector may fall, which could cause an
injury.
Attention
• Do not transport the projector with the lens installed. Doing so could damage
the projector and the lens.
• If the projector does not have a lens, attach the cover that was on the lens mount
when you purchased the projector.
27
Page 28
Precautions on Installation
28
You can install the projector or mount it to the ceiling at any horizontal or
vertical angle. Note the following precautions when installing the projector.
Warning
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
Warning
• Do not use adhesives on the ceiling mount fixing points to prevent the screws
from loosening, or use lubricants, oils, or similar substances on the projector; the
projector case may crack causing it to fall from its ceiling mount. This could
cause serious injury to anyone under the ceiling mount and could damage the
projector.
• Do not install the projector in a location subject to high levels of dust or
humidity, or in a location subject to smoke or steam. Otherwise, it could cause a
fire or electric shock to occur. The projector's case could also deteriorate and be
damaged causing the projector to fall from the mount.
Examples of environments that could cause the projector to fall due to case
deterioration
• Locations subject to excessive smoke or airborne oil particles, such as factories
or kitchens
• Locations containing volatile solvents or chemicals, such as factories or
laboratories
• Locations where the projector could be subjected to detergents or chemicals,
such as factories or kitchens
• Locations in which aroma oils are often used, such as relaxation rooms
• Near devices that produce excessive smoke, airborne oil particles, or foam at
events
Attention
• Use M6 screws (up to a depth of 14 mm) to fix the projector's ceiling mount
fixing points and the mounting hardware at four points.
• Do not stack projectors directly on top of each other.
Attention
Install the current breaker for 13 A to 20 A to the wiring in the building that
supplies electricity to the projector. Do not connect other devices to the wiring
where the current breaker is installed, and use the wiring only for the projector.
Page 29
Precautions on Installation
29
Installation space
Attention
• Be sure to leave the following amount of space around the projector so as not to
block the air exhaust and intake vents.
Installation space (When installing multiple projectors side by side)
Attention
• If you are installing multiple projectors next to each other, make sure hot air
from the exhaust vent does not go into the air intake vent of another projector.
• If you use a partition, you can narrow the space between the projectors.
• Do not install the projector in a location that does not allow air to circulate, such
as on a shelf or in a box.
Page 30
Attaching and Removing a Lens
30
Follow the instructions in these sections to attach or remove a compatible
lens.
The following lens are available.
• ELPLX02S
• ELPLX02WS
• ELPLU03S
• ELPLU04
• ELPLW08
• ELPLW06
• ELPLM15
• ELPLM10
• ELPLM11
• ELPLL08
Warning
Make sure you turn off the projector and unplug the power cord before attaching
or removing a lens. Otherwise, you may receive an electric shock.
Attention
• If dust or dirt gets inside the projector, projection quality deteriorates and it
could cause a malfunction. Be sure to observe the following precautions when
handling.
• Make sure the front of the projector is not facing up when you attach or
remove the lens.
• Remove the lens only when necessary.
• Store the projector with the lens installed.
• Avoid touching the lens with your bare hands to prevent fingerprints on or
damage to the lens surface.
Attaching a Lens
You can attach a compatible lens to the projector.
For information on installing an ultra short-throw zoom lens, see the
a
a
b
User's Guide supplied with the lens.
Turn off the projector and unplug the power cord.
Remove the lens replacement cover.
gg Related Links
• "Attaching a Lens" p.30
• "Removing a Lens" p.34
Page 31
Attaching and Removing a Lens
31
Pinch the lock lever and move it to the Release position.
c
Insert the lens straight into the projector's lens socket with the white
d
dot facing up.
Caution
To avoid injury, be careful not to get your fingers caught between the
projector and lens.
Page 32
Attaching and Removing a Lens
32
Hold the lens firmly, then pinch the lock lever and move it to the Lock
e
position.
Warning
Make sure the lens is secured.
If the lens is not secured, it may fall off and could cause an injury when
moving the projector.
If you want to secure the lens more firmly, tighten the screw next to the
f
lock lever using a hexagonal wrench (2.5mm).
If you are using the ELPLX02S/ELPLX02WS, the lens is secured
a
even without using the screw lock.
Page 33
Attaching and Removing a Lens
33
Replace the lens replacement cover.
g
If projecting down, we recommend securing the lens
a
replacement cover with commercially available screws
(M3×12mm).
To perform lens calibration, turn on the projector.
h
When a message prompting you to start lens calibration is displayed,
i
select Yes.
Lens calibration starts and helps the projector to correctly acquire the
lens position and adjustment range. It takes up to 100 seconds. When
calibration is finished, the lens returns to its original position.
The following lenses return to the standard position.
• ELPLX02S
• ELPLX02WS
• If no message is displayed after turning on the projector,
a
perform lens calibration manually using one of the following
methods.
• Hold down the [Default] button on the remote control for
approximately 3 seconds.
• Change the projector's menu:
s Extended > Operation > Lens Calibration
• If you do not calibrate the lens, the following functions may
not operate correctly.
• Focus
• Distortion
• Zoom
• Lens Shift
• Memory (Lens Position)
Attention
If the icon indicating that lens calibration has failed is displayed, remove the
lens and then reinstall it. If the message continues to be displayed, stop
using the projector, remove the power plug from the electrical outlet, and
contact Epson for help.
Page 34
Attaching and Removing a Lens
34
If you are projecting from a table or other flat surface, the image may
a
be tilted depending on your lens. Adjust the tilt of the image using the
front and rear feet.
Removing a Lens
You can remove a lens to replace it with a different lens.
Caution
Wait at least 30 minutes to remove or replace the lens after turning off the
projector. Touching the lens unit before it cools down may cause burns.
The projector uses a laser as the light source. As a safety measure, the
a
a
light source turns off when the lens is removed. Attach the lens, and
then press the [On] button to turn it back on.
Hold down the [Lens Shift] (remote control) or [Lens] (control panel)
button for approximately 3 seconds to move the lens to the home
position.
If necessary, loosen the screw next to the lock lever.
d
Turn off the projector and unplug the power cord.
b
Remove the lens replacement cover.
c
Page 35
Attaching and Removing a Lens
Hold the lens firmly as you pinch the lock lever and move it to the
e
Release position.
35
Gently pull the lens straight out of the projector.
f
Page 36
Attaching and Removing the Cable Cover
36
When suspending the projector from a ceiling, you can attach the cable cover
that came with your projector to hide the attached cables from view.
Pass a commercially available cable tie through the cable holder and tie
a
the cables together.
Caution
Place the cable cover on the projector as shown, guiding the cables
b
through the notch on the base of the cable cover.
Tighten the cable cover screws.
c
Do not bundle the power cord to the other cables. Otherwise, a fire may
occur.
Page 37
Operating the Projector Power
37
Follow the instructions in these sections to operate the projector power.
gg Related Links
• "Turning On the Projector" p.37
• "Turning Off the Projector" p.38
Turning On the Projector
Turn on the computer or video equipment you want to use after you turn on
the projector.
Connect the power cord to the projector's power inlet and plug it into
a
an electrical outlet.
You can use a 100 V power cord to operate the projector
a
If necessary, lock the power cord to prevent it from falling off.
b
temporarily to determine the installation location. When
projecting using the 100 V power cord, the brightness of the
projected image is approximately 60% compared to when using a
200 V power cord. Use the 200 V power cord when adjusting the
projected image or the lens. You cannot use the following
functions with the 100 V power cord.
• Light Source Mode
• Estimated Remains
• Refresh Mode
• Light Source Calibration
Be sure to ground the power plug using a grounding wire or a 3core power plug.
The projector's power indicator turns blue. This indicates that the
projector is receiving power, but is not yet turned on (it is in standby
mode).
Press the [On] button on the control panel or remote control to turn on
c
the projector.
Page 38
Operating the Projector Power
38
The projector beeps and the status indicator flashes blue as the
projector warms up. Once the projector is warmed up, the status
indicator stops flashing and turns blue.
• When Quick Startup is enabled in the projector's Extended
a
Try the following if you do not see a projected image.
• Turn on the connected computer or video device.
• Change the screen output from the computer when using a laptop
computer.
• Insert a DVD or other video media, and press play (if necessary).
• Press the [Search] button on the control panel or remote control to detect
the source.
• Press the button for the desired video source on the remote control.
• If the Home screen is displayed, select the source you want to project.
menu, the projector becomes ready for use in several seconds
the next time you press the power button.
s Extended > Operation > Quick Startup
Warning
• Never look into the projector lens when the light source is on. This can damage
your eyes and is especially dangerous for children.
• When turning on the projector at a distance using the remote control, make sure
there is no one looking into the lens.
• During projection, do not block the light from the projector with a book or other
objects. If the light from the projector is blocked, the area on which the light
shines becomes hot which could cause it to melt, burn, or start a fire. Also, the
lens may get hot due to the reflected light which could cause the projector to
malfunction. To stop projection, use the A/V Mute or Shutter function, or turn
off the projector.
• When the Direct Power On setting is set to On in the projector's
a
gg Related Links
• "Home Screen" p.51
Extended menu, the projector turns on as soon as you plug it in.
Note that the projector also turns on automatically in cases such as
recovery from a power outage.
s Extended > Operation > Direct Power On
• If you select a specific port as the Auto Power On setting in the
projector's Extended menu, the projector turns on as soon as it
detects a signal or cable connection from that port.
s Extended > Operation > Auto Power On
Turning Off the Projector
Turn off the projector after use.
• Turn off this product when it is not in use to prolong the life of the
a
projector. Light source life varies depending on the mode selected,
environmental conditions, and usage. Brightness decreases over time.
• Light source calibration starts automatically if you turn off the
projector and the following conditions are present:
• The Light Source Calibration setting is set to Run Periodically in
the projector's Reset menu
• 100 hours have passed since the last light source calibration
• You have used the projector continuously for more than 20
minutes
• Since the projector supports the direct shutdown feature, it can be
turned off directly using the breaker.
Press the [Standby] button on the control panel or remote control.
a
The projector displays a shutdown confirmation screen.
Press the [Standby] button again. (To leave it on, press any other
b
button.)
Page 39
Operating the Projector Power
The projector beeps twice, the light source turns off, and the status
indicator turns off.
To transport or store the projector, make sure the status indicator on
c
the projector is off, and then unplug the power cord.
39
Page 40
Wired Network Connection
40
You can send images to your projector, as well as monitor and control your
projector, over a network.
To perform these operations, you need to do the following first:
• Connect the projector to your network.
• Set up your projector and computer using the projector's Network menus.
• Download and install the following network software from the following
Web site.
epson.sn
• Epson iProjection software sets up your computer for network projection.
It also allows you to hold interactive meetings by projecting the user's
computer screen over a network. See the Epson iProjection Operation
Guide (Windows/Mac) for instructions.
• Epson Projector Management software (Windows only) sets up your
computer for monitoring and controlling projectors. See the Epson
Projector Management Operation Guide for instructions.
gg Related Links
• "Connecting to a Wired Network" p.40
• "Selecting Wired Network Settings" p.40
Connecting to a Wired Network
To connect the projector to a wired local area network (LAN), use a 100BaseTX or 10Base-T network cable. To ensure proper data transmission, use a
Category 5 shielded cable or better.
Connect one end of the network cable to your network hub, switch, or
a
router.
Connect the other end of the cable to the projector's LAN port.
b
Selecting Wired Network Settings
Before you can project from computers on your network, you need to select
network settings on the projector.
Make sure you already connected the projector to your wired network
a
a
b
c
d
using the LAN port.
Press the [Menu] button, select the Network menu, and press [Enter].
Select Network Configuration and press [Enter].
Select the Basic menu and press [Enter].
Select the basic options as necessary.
• Projector Name lets you enter a name up to 16 alphanumeric
characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric
characters long for using the PJLink protocol for projector control.
• Remote Password lets you enter a password up to 32 alphanumeric
characters long to access the projector using the Basic Control. (User
name is EPSONREMOTE; default password is the projector's serial
number.)
• Web Control Password lets you enter a password up to 32
alphanumeric characters long to access the projector over the Web.
(User name is EPSONWEB; default password is the projector's serial
number.)
• Moderator Password lets you enter a four-digit number password
for accessing the projector as a moderator using Epson iProjection.
(No password is set by default.)
• Projector Keyword lets you turn on a security password to prevent
access to the projector by anyone not in the room with it. You must
enter a displayed, randomized keyword from a computer using
Epson iProjection to access the projector and share the current
screen.
Page 41
Wired Network Connection
41
• Display Keyword lets you select whether to display a projector
keyword on the projected image when accessing the projector using
Epson iProjection.
• Display LAN Info. lets you set the display format for the projector's
network information.
Use the displayed keyboard to enter numbers and characters.
a
Select the Wired LAN menu and press [Enter].
e
Assign the IP settings for your network as necessary.
f
• If your network assigns addresses automatically, select IP Settings to
set the DHCP setting to On.
• If you must set addresses manually, select IP Settings to set the
DHCP setting to Off, and then enter the projector's IP Address,
Subnet Mask, and Gateway Address as necessary.
• If you want to connect the projector to the network using IPv6, select
IPv6 Settings to set the IPv6 setting to On, and then set the Auto
Configuration and Use Temporary Address settings as necessary.
Press the arrow buttons on the remote control to highlight
characters and press [Enter] to select them.
You can also enter numbers by pressing the number buttons
while holding down the [Num] button on the remote control.
The wired network settings complete when you see the correct IP
address on the LAN standby screen.
gg Related Links
• "Using the Displayed Keyboard" p.53
To highlight the numbers you want from the displayed keyboard,
a
To prevent the IP address from being displayed on the LAN standby
g
screen and Home screen, set the IP Address Display setting to Off.
When you finish selecting settings, select Complete and follow the on-
h
screen instructions to save your settings and exit the menus.
Press the [LAN] button on the remote control.
i
press the arrow buttons on the remote control. To select a
highlighted number, press [Enter].
Page 42
Wireless Network Connection
42
You can send images to your projector, as well as monitor and control your
projector, over a network.
To perform these operations, you need to do the following first:
• Install the Epson 802.11a/b/g/n wireless LAN module onto the projector.
• Set up your projector and computer using the projector's Network menus.
• Download and install the following network software from the following
Web site.
epson.sn
• Epson iProjection (Windows/Mac) software allows you to hold interactive
meetings by projecting the user's computer screen over a network. See the
Epson iProjection Operation Guide (Windows/Mac) for instructions.
• Epson iProjection (iOS/Android) app allows you to project from iOS,
Android, or Chromebook devices.
You can download Epson iProjection for free from the App Store or
Google Play. Any fees incurred when communicating with the App Store
or Google Play are the responsibility of the customer.
• Epson Projector Management software (Windows only) sets up your
computer for monitoring and controlling projectors. See the Epson
Projector Management Operation Guide for instructions.
gg Related Links
• "Installing the Wireless LAN Module" p.42
• "Selecting Wireless Network Settings Manually" p.43
• "Selecting Wireless Network Settings in Windows" p.44
• "Selecting Wireless Network Settings in Mac" p.44
• "Setting Up Wireless Network Security" p.44
• "Using a QR Code to Connect a Mobile Device" p.46
• "Using a USB Key to Connect a Windows Computer" p.47
Attention
Never remove the module while the WLAN (wireless LAN) indicator on the
projector is blue or flashing, or while you are projecting wirelessly. This could
damage the module or lose data.
Turn off the projector and unplug the power cord.
a
Loosen the screws and remove the wireless LAN module cover as
b
shown.
Connect the Wireless LAN module to the wireless LAN module slot.
c
Installing the Wireless LAN Module
To use the projector over a wireless network, install the Epson 802.11a/b/g/n
wireless LAN module. Do not install any other type of wireless LAN module.
Page 43
Wireless Network Connection
43
Replace the wireless LAN module cover as shown and tighten the
d
screws.
Selecting Wireless Network Settings Manually
Before you can project from your wireless network, you need to select
network settings for the projector.
• Remote Password lets you enter a password up to 32 alphanumeric
characters long to access the projector using the Basic Control. (User
name is EPSONREMOTE; default password is the projector's serial
number.)
• Web Control Password lets you enter a password up to 32
alphanumeric characters long to access the projector over the Web.
(User name is EPSONWEB; default password is the projector's serial
number.)
• Moderator Password lets you enter a four-digit number password
for accessing the projector as a moderator using Epson iProjection.
(No password is set by default.)
• Projector Keyword lets you turn on a security password to prevent
access to the projector by anyone not in the room with it. You must
enter a displayed, randomized keyword from a computer using
Epson iProjection to access the projector and share the current
screen.
• Display Keyword lets you select whether to display a projector
keyword on the projected image when accessing the projector using
Epson iProjection.
• Display LAN Info. lets you set the display format for the projector's
network information.
Press the [Menu] button, select the Network menu, and press [Enter].
a
Select On as the Wireless LAN Power setting.
b
Select Network Configuration and press [Enter].
c
Select the Basic menu and press [Enter].
d
Select the basic options as necessary.
e
• Projector Name lets you enter a name up to 16 alphanumeric
characters long to identify the projector over the network.
• PJLink Password lets you enter a password up to 32 alphanumeric
characters long for using the PJLink protocol for projector control.
Use the displayed keyboard to enter numbers and characters.
a
Select the Wireless LAN menu and press [Enter].
f
Select the Connection Mode setting.
g
• Quick lets you connect to multiple smartphones, tablets, or
computers directly using wireless communication.
• Advanced lets you connect to smartphones, tablets, or computers
over a wireless network access point.
Press the arrow buttons on the remote control to highlight
characters and press [Enter] to select them.
You can also enter numbers by pressing the number buttons
while holding down the [Num] button on the remote control.
Page 44
Wireless Network Connection
44
If you selected the Advanced connection mode, select Search Access
h
Point to select the access point you want to connect to.
If you need to assign the SSID manually, select SSID to enter the
a
For the Advanced connection mode, assign the IP settings for your
i
network as necessary.
• If your network assigns addresses automatically, select IP Settings to
set the DHCP setting to On.
• If you must set addresses manually, select IP Settings to set the
DHCP setting to Off, and then enter the projector's IP Address,
Subnet Mask, and Gateway Address as necessary.
• If you want to connect the projector to the network using IPv6, select
IPv6 Settings to set the IPv6 setting to On, and then set the Auto
Configuration and Use Temporary Address settings as necessary.
To prevent the SSID or IP address from being displayed on the LAN
j
standby screen and Home screen, set the SSID Display setting or the IP
Address Display setting to Off.
When you finish selecting settings, select Complete and follow the on-
k
screen instructions to save your settings and exit the menus.
SSID.
Selecting Wireless Network Settings in Windows
Before connecting to the projector, select the correct wireless network on your
computer.
To access your wireless utility software, click the network icon on the
a
Windows taskbar.
When connecting in Advanced connection mode, select the network
b
name (SSID) of the network the projector is connecting to.
Click Connect.
c
Selecting Wireless Network Settings in Mac
Before connecting to the projector, select the correct wireless network in Mac.
Click the Wi-Fi icon on the menu bar at the top of the screen.
a
When connecting in Advanced connection mode, make sure Wi-Fi is
b
turned on and select the network name (SSID) of the network the
projector is connecting to.
Press the [LAN] button on the remote control.
l
The wireless network settings are complete when you see the correct IP
address on the LAN standby screen.
When you have finished making wireless settings for your projector, you need
to select the wireless network on your computer. Then start the network
software to send images to your projector through a wireless network.
gg Related Links
• "Using the Displayed Keyboard" p.53
Setting Up Wireless Network Security
You can set up security for your projector to use on a wireless network. Set up
one of the following security options to match the settings used on your
network:
• WPA2-PSK security *
• WPA3-PSK security **
• WPA2/WPA3-PSK security **
• WPA3-EAP security **
• WPA2/WPA3-EAP security **
Page 45
Wireless Network Connection
45
* Available only for the Quick connection mode.
** Available only for the Advanced connection mode.
Contact your network administrator for guidance on entering the
a
a
b
c
d
e
f
g
h
i
correct information.
If you want to set up the WPA3-EAP or WPA2/WPA3-EAP security,
make sure your digital certificate file is compatible with projector
registration and placed directly on the USB storage device.
Press the [Menu] button, select the Network menu, and press [Enter].
Select Network Configuration and press [Enter].
Select the Wireless LAN menu and press [Enter].
Select the Security setting and press [Enter].
Select the security settings to match your network settings.
Do one of the following according to the security you selected.
• WPA2-PSK, WPA3-PSK, or WPA2/WPA3-PSK: Select Complete
and follow the on-screen instructions to save your settings and exit
the menus.
• WPA3-EAP, WPA2/WPA3-EAP: Select EAP Method and press
[Enter].
Select the protocol for authentication as the EAP Type setting.
To import your certificate, select the certificate type and press [Enter].
• Client Certificate for the PEAP-TLS or EAP-TLS type
• CA certificate for all EAP types
You can also register the digital certificates from your Web
a
Select Register and press [Enter].
j
Follow the on-screen instructions to connect a USB storage device to
k
the projector's USB-A port.
Press [Enter] to display the certificate list.
l
Select the certificate to import using the displayed list.
m
A message is displayed prompting you to enter the password for the
certificate.
Enter a password and press [Enter].
n
The certificate is imported and a completion message appears.
Select your EAP settings as necessary.
o
• User name lets you enter a user name using up to 64 alphanumeric
characters. To enter more than 32 characters, use your Web browser.
When importing a client certificate, the name the certificate was
issued to is automatically set.
• Password lets you enter a password using up to 64 alphanumeric
characters for authentication when using the PEAP, EAP-FAST, or
LEAP type. To enter more than 32 characters, use your Web
browser.
• Verify Server Cert. lets you select whether or not to verify the server
certificate when a CA certificate has been set.
• RADIUS Serv.Name lets you enter the server name to be verified.
When you have finished making settings, select Complete and follow
p
the on-screen instructions to save your settings and exit the menus.
browser. However, be sure to register just once or the certificate
may not install correctly.
Page 46
Wireless Network Connection
46
gg Related Links
• "Supported Client and CA Certificates" p.46
Supported Client and CA Certificates
You can register these types of digital certificates.
Client Certificate (PEAP-TLS/EAP-TLS)
Specification Description
Format PKCS#12
Extension PFX, P12
Encryption RSA
Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length 512/1024/2048/4096 bit
Password * Up to 64 alphanumeric characters; required
CA Certificate (PEAP/PEAP-TLS/EAP-TLS/EAP-FAST)
Specification Description
Format X509v3
Extension DER/CER/PEM
Encryption RSA
Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length 512/1024/2048/4096 bit
Encoding BASE64/Binary
Using a QR Code to Connect a Mobile Device
After selecting the wireless network settings for your projector, you can
display a QR code on the screen and use it to connect a mobile device using
the Epson iProjection (iOS/Android) app.
• Make sure you have installed the latest version of Epson iProjection
a
Press the [LAN] button on the remote control.
a
The QR code is displayed on the projected surface.
Start Epson iProjection on your mobile device.
b
Read the projected QR code using Epson iProjection to connect it to
c
the projector.
on your device.
• You can download Epson iProjection for free from the App Store or
Google Play. Any fees incurred when communicating with the App
Store or Google Play are the responsibility of the customer.
• When using Epson iProjection in Quick connection mode, we
recommend making security settings.
• If you do not see the QR code, set the Display LAN Info.
a
setting to Text & QR Code in the projector's Network menu.
s Network > Network Configuration > Basic > Display
LAN Info.
• To hide the QR code, press [Esc].
• When the QR code is hidden, press [Enter] to display the code.
* You need to use your Web browser to enter more than 32 characters.
To correctly read the QR code, make sure you face the screen
a
When a connection is established, select Contents menu from , and
then select the file you want to project.
squarely and closely enough so that the projected code fits into
the guide of the mobile device's QR code reader. If you are too
far from the screen, the code may not be read.
Page 47
Wireless Network Connection
47
Using a USB Key to Connect a Windows Computer
You can set up your USB flash drive as a USB key to quickly connect the
projector to a wireless LAN supported Windows computer. After creating the
USB key, you can quickly project images from the network projector.
Set up the USB key using USB Key Setup Tool of the Epson iProjection
a
(Windows) software.
See the Epson iProjection Operation Guide (Windows/Mac) for
a
Make sure the wireless LAN module is installed into your projector.
b
Turn on the projector.
c
Press the [LAN] button on the remote control.
d
The LAN standby screen is displayed. Verify that an SSID and IP
address are displayed.
Remove the wireless LAN module from the projector's USB-A port (if
e
installed) and insert the USB key into the same port.
You see a projected message that the network information update is
complete.
instructions.
• If the Windows Firewall message is displayed, click Yes to
a
After a few minutes, your computer image is displayed by the projector.
When you have finished projecting wirelessly, select the Safely Remove
i
Hardware option in the Windows taskbar, and then remove the USB
key from your computer.
a
disable the firewall.
• You need administrator authority to install the software.
• If it is not installed automatically, double-click
MPPLaunch.exe in the USB key.
You may need to restart your computer to reactivate your
wireless LAN connection.
Remove the USB key.
f
If your projector needs the wireless LAN module, reinsert the wireless
LAN module into the projector.
Connect the USB key to a USB port on your computer.
g
Follow the on-screen instructions to install the necessary application.
h
Page 48
Secure HTTP
48
You can use the HTTPS protocol to increase security between the projector
and a Web browser communicating with it. To do this, you create a server
certificate, install it on the projector, and turn on the Secure HTTP setting in
the projector menus to verify the reliability of the Web browser.
s Network > Network Configuration > Others > Secure HTTP
Even if you do not install a server certificate, the projector automatically
creates a self-signed certificate and allows communication. However, because
the self-signed certificate cannot verify reliability from a Web browser, you
see a warning about the server's reliability when you access the projector from
a Web browser. This warning does not prevent communication.
gg Related Links
• "Importing a Web Server Certificate Using the Menus" p.48
Importing a Web Server Certificate Using the Menus
You can create your Web server certificate and import it using the projector
menus and an external storage device.
• You can use a USB flash drive as an external storage device for this
a
model.
• You can also register the digital certificates from your Web browser.
However, be sure to register just once or the certificate may not
install correctly.
Select Web Server Cert. and press [Enter].
f
Select Register and press [Enter].
g
Follow the on-screen instructions to connect a USB storage device to
h
the projector's USB-A port.
Press [Enter] to display the certificate list.
i
Select the certificate to import using the displayed list.
j
A message is displayed prompting you to enter the password for the
certificate.
Enter a password and press [Enter].
k
The certificate is imported and a completion message appears.
gg Related Links
• "Supported Web Server Certificates" p.48
Supported Web Server Certificates
You can register these types of digital certificates.
Web Server Certificate (Secure HTTP)
Make sure your digital certificate file is compatible with projector
a
registration and directly placed on the USB storage device.
Press the [Menu] button, select the Network menu, and press [Enter].
b
Select Network Configuration and press [Enter].
c
Select the Others menu and press [Enter].
d
Set the Secure HTTP setting to On.
e
Specification Description
Format PKCS#12
Extension PFX, P12
Encryption RSA
Hashes MD5/SHA-1/SHA-256/SHA-384/SHA-512
Key length 512/1024/2048/4096 bit
Common name Network host name
Organization Optional
Password * Up to 64 alphanumeric characters; required
Page 49
Secure HTTP
* You need to use your Web browser to enter more than 32 characters.
49
Page 50
Adjusting the Menu Settings
Follow the instructions in these sections to access the projector menu system and change projector settings.
gg Related Links
• "Home Screen" p.51
• "Using the Projector's Menus" p.52
• "Using the Displayed Keyboard" p.53
• "Using Basic Projector Features" p.54
• "Copying Menu Settings Between Projectors (Batch Setup)" p.68
Page 51
Home Screen
51
The Home screen feature allows you to easily select an image source and
access useful functions.
You can display the Home screen by pressing the [Home] button on the
remote control. If you want to display the Home screen when you turn on the
projector and no signal is being input, set Home Screen Auto Disp. to On.
s Extended > Home Screen > Home Screen Auto Disp.
Press the arrow buttons on the remote control to select a menu item, and then
press [Enter].
Changes the projector's color mode.
H
After 10 minutes of inactivity, the Home screen disappears and you are
a
returned to the screen that you were on before (the current input
source screen or no signal message).
Selects the source you want to project.
A
Displays the Connection Guide. You can select the wireless connection methods
B
according to the devices you are using, such as smartphones or computers.
Indicates the projector is in Content Playback mode.
C
Displays the Help screen.
D
Displays the projector's menu.
E
Performs menu options assigned to Home Screen in the projector's Extended
F
menu.
Selects the brightness for the light source.
G
Page 52
Using the Projector's Menus
52
You can use the projector's menus to adjust the settings that control how your
projector works. The projector displays the menus on the screen.
Press the [Menu] button on the control panel or remote control.
a
You see the menu screen displaying the Image menu settings.
Press the up or down arrow buttons to move through the menus listed
b
on the left. The settings for each menu are displayed on the right.
Press [Menu] or [Esc] to exit the menus.
h
The available settings depend on the current input source.
a
To change settings in the displayed menu, press [Enter].
c
Press the up or down arrow button to move through the settings.
d
Change the settings using the buttons listed on the bottom of the menu
e
screens.
To return all the menu settings to their default values, select Reset.
f
When you finish changing settings on a menu, press [Esc].
g
Page 53
Using the Displayed Keyboard
53
You can use the displayed keyboard to enter numbers and characters.
Use the arrow buttons on the control panel or remote control to
a
highlight the number or character you want to enter and press the
[Enter] button.
Each time you select the CAPS key, the characters change
a
After entering the text, select Finish on the keyboard to confirm your
b
entries. Select Cancel to cancel entering text.
between upper case and lower case. Each time you select the
SYM1/2 key, the symbols enclosed by the frame change.
Text type Details
Numbers 0123456789
Alphabet ABCDEFGHIJKLMNOPQRSTUVWXY
Z
abcdefghijklmnopqrstuvwxyz
Symbols ! " # $ % & ' ( ) * + , - . / : ; < = > ? @ [ \ ]
^ _ ` { | } ~
You can select projector settings and control projection over a network
a
gg Related Links
• "Available Text Using the Displayed Keyboard" p.53
using a Web browser from your computer.
Some symbols cannot be entered using the displayed keyboard. Use
your Web browser to enter the text.
Available Text Using the Displayed Keyboard
You can enter the following text when using the displayed keyboard.
Page 54
Using Basic Projector Features
54
Follow the instructions in these sections to use your projector's basic features.
gg Related Links
• "Setting Up the Projector" p.54
• "Projecting Images" p.56
• "Adjusting the Image Position and Shape" p.59
• "Adjusting the Image Quality" p.61
• "Using Multiple Projectors" p.62
• "Maintaining the Projector Quality" p.64
• "Managing the Projector's Settings" p.65
Setting Up the Projector
This section provides instructions on setting up your projector.
gg Related Links
• "Messages" p.54
• "Standby Confirmation" p.54
• "Sleep Mode" p.54
• "Beep" p.54
• "Indicators" p.55
• "Date & Time" p.55
• "Language" p.55
• "On-Screen Display" p.55
• "Energy Saving Mode" p.55
• "Remote Control Type" p.56
Messages
Execution Method
s Extended > Display > Messages
Standby Confirmation
When set to Off, you can turn off the projector simply by pressing the power
button once.
Execution Method
s Extended > Display > Standby Confirmation
Sleep Mode
When set to On, the projector automatically turns off after an interval of
inactivity.
You can also set the interval in the Sleep Mode Timer setting.
Execution Method
s Extended > Operation > Sleep Mode
s Extended > Operation > Sleep Mode Timer
Beep
When set to Off, you can turn off the confirmation buzzer beeps to notify you
that the power turns on or off, or cooling down is finished.
Execution Method
s Extended > Operation > Advanced > Beep
You can display or hide messages such as the input source name, color mode
name, aspect ratio, no signal message, or high temperature warning on the
projected image.
Page 55
Using Basic Projector Features
55
Indicators
When set to Off, you can turn off the indicator lights on the projector.
Execution Method
s Extended > Operation > Advanced > Indicators
Date & Time
You can adjust the projector's system time and date settings.
Execution Method
s Extended > Operation > Date & Time
Language
You can select the language for projector menu and message displays.
Execution Method
• Menus and messages are displayed or hidden each time you press the
a
button.
• If On-Screen Display is enabled, you cannot operate the projector's
menu (except to switch the color mode and input source).
Energy Saving Mode
When set to On, you can reduce the power consumption by automatically
adjusting the light source brightness. The light source brightness is gradually
adjusted over a period of 60 minutes and it does not ruin the image
appearance.
When you use the Multi-Projection or Constant Brightness features, set to
Off to correct differences in the brightness between projectors.
Execution Method
s Settings > Brightness Settings > Energy Saving Mode
This function is disabled in the following cases:
a
• When Edge Blending is set to Blending/Black Level or Black Level.
s Extended > Multi-Projection > Edge Blending
• When Color Mode is set to Multi-Projection.
s Image > Color Mode
• When Light Source Mode is set to Custom.
s Settings > Brightness Settings > Light Source Mode
s Extended > Language
On-Screen Display
You can display or hide the menus or messages on the projected image. Make
sure you assign On-Screen Display to any [User] button on the remote
control in the Settings menu.
s Settings > User Button
Execution Method
Press the [User] button on the remote control to which On-Screen Display is
assigned.
Page 56
Using Basic Projector Features
56
Remote Control Type
If you want to adjust the zoom/focus/distortion of the projected image using
the Epson remote control as shown below, select Advanced as the Remote
Control Type setting.
Execution Method
s Extended > Operation > Advanced > Remote Control Type
• "Test Pattern" p.58
• "Content Playback" p.59
• "Display Background" p.59
• "Startup Screen" p.59
Source Search
When multiple image sources are connected to the projector, such as a
computer and DVD player, you can switch from one image source to the
other.
Execution Method
• Press the [Search] (remote control) or [Source Search] (control panel)
button on the control panel or remote control until you see the image from
the source you want.
• Press the button for the source you want on the remote control. If there is
more than one port for that source, press the button again to cycle through
the sources.
• Press the [Home] button on the remote control. Then select the source you
want to use from the screen displayed.
A/V Mute
Projecting Images
This section provides instructions to project images.
gg Related Links
• "Source Search" p.56
• "A/V Mute" p.56
• "Shutter" p.57
• "Freeze" p.57
• "Split Screen" p.57
• "Volume" p.57
• "Aspect" p.57
• "Screen Type" p.58
• "Projection" p.58
You can temporarily turn off the projected image and sound. Any sound or
video action continues to run, however, so you cannot resume projection at
the point that you stopped it (EB‑PU2120W).
Execution Method
Press the [A/V Mute] button on the control panel or remote control. To turn
the image and sound back on, press [A/V Mute] again.
Page 57
Using Basic Projector Features
57
• You can add a fade out or fade in effect when turning the video on or
a
off.
• You can limit the way the A/V Mute function is released.
s Extended > Operation > A/V Mute Settings
Shutter
You can temporarily hide the projected image and sound by closing the
mechanical shutter. Any sound or video action continues to run, however, so
you cannot resume projection at the point that you closed the shutter
(EB‑PU2220B).
Execution Method
Press the [A/V Mute] button on the control panel or remote control. To turn
the image and sound back on, press [A/V Mute] again.
Press the [Freeze] button on the remote control. To restart the video action in
progress, press [Freeze] again.
Split Screen
You can use the Split Screen feature to simultaneously project two images
from different image sources.
Execution Method
• Press the [Split] buttons on the remote control
• Change the projector's menu:
s Settings > Split Screen
• You can add a fade out or fade in effect when turning the video on or
a
off.
• You can limit the way the shutter function is released.
s Extended > Operation > Shutter Settings
Freeze
You can temporarily stop the action in a video or computer presentation and
keep the current image on the screen. Any sound or video action continues to
run, however, so you cannot resume projection at the point that you stopped
it.
Execution Method
Volume
You can adjust the volume of the audio from the Audio Out port.
Execution Method
• Press the [Volume] buttons on the remote control.
• Change the projector's menu:
s Settings > Volume
Aspect
The projector can display images in different width-to-height ratios called
aspect ratios. Normally, the input signal from your video source determines
Page 58
Using Basic Projector Features
58
the image's aspect ratio. However, you can change the aspect ratio for certain
images to fit your screen.
Execution Method
• Press the [Aspect] button on the remote control.
• Change the projector's menu:
s Signal > Aspect
If you always want to use a particular aspect ratio for a certain video
a
Screen Type
You can use the Screen Type setting to match the aspect ratio of the displayed
image to the screen you are using.
Execution Method
input source, you can select it using the projector's Signal menu.
Projection
You can change the projection mode to flip the image over top-to-bottom
and/or left-to-right using the projector menus.
Execution Method
s Extended > Projection
You can change the projection mode to flip the image over top-to-
a
Test Pattern
You can display a test pattern to adjust the projected image without
connecting a computer or video device.
bottom by holding down the [A/V Mute] button on the remote control
for approximately 5 seconds.
s Extended > Display > Screen > Screen Type
• Adjust the aspect ratio for the projected image, if necessary.
a
• When the Screen Type setting changes, the EDID settings are
automatically adjusted.
Execution Method
• Press the [Test Pattern] button on the control panel or remote control.
• Change the projector's menu:
s Settings > Test Pattern
Page 59
Using Basic Projector Features
59
Content Playback
Your projector's Content Playback feature allows you to project your digital
signage content. You can also add color and shape effects to your projected
image.
You can use the following software to create content that can be played in
Content Playback mode.
• Epson Projector Content Manager
• Epson Web Control
• Epson Creative Projection
Execution Method
s Extended > Display > Startup Screen
Adjusting the Image Position and Shape
This section provides instructions to adjust the image position and shape
without moving the projector.
gg Related Links
• "Lens Shift" p.59
• "Zoom" p.60
• "H/V-Keystone" p.60
• "Quick Corner" p.60
• "Curved Surface" p.60
• "Corner Wall" p.61
• "Point Correction" p.61
Lens Shift
If you cannot install the projector directly in front of the screen, you can
adjust the position of the projected image using the lens shift feature.
Execution Method
s Settings > Content Playback
Display Background
You can select the screen background when no image signal is available.
Execution Method
s Extended > Display > Display Background
Startup Screen
When set to On, a logo is displayed when the projector starts up.
You can check the available lens shift range in the projector's Specifications.
Execution Method
• Press the [Lens Shift] button on the remote control.
• Press the [Lens] button on the control panel until the lens shift adjustment
screen is displayed.
Page 60
Using Basic Projector Features
60
Caution
When shifting the lens, do not put your hands near the lens unit. Your fingers may
get caught between the lens unit and the projector, and cause an injury.
• Wait 20 minutes after turning on the projector before setting the lens
a
Zoom
You can resize the image.
shift for maximum accuracy.
• When adjusting the image height, position the image lower than
where you want it to be and then move it up. This will help prevent
the image from moving down after adjustment.
• The image is clearest when the lens is at the home position. To move
the lens to the home position, hold the [Lens Shift] button on the
remote control or the [Lens] button on the control panel for more
than 3 seconds.
H/V-Keystone
You can correct distortion in the horizontal and vertical directions
independently.
Execution Method
s Settings > Geometry Correction > H/V-Keystone
Quick Corner
You can correct each of the four corners of the projected image
independently.
Execution Method
• Press the [Zoom] button on the remote control.
• Press the [Lens] button on the control panel until the zoom adjustment
screen is displayed.
• Use the arrow buttons on the control panel or remote control to adjust the
image size.
Execution Method
s Settings > Geometry Correction > Quick Corner
Curved Surface
You can correct the corners and sides of an image projected on a curved
surface with the same radius.
Page 61
Using Basic Projector Features
61
Execution Method
s Settings > Geometry Correction > Curved Surface
Corner Wall
You can correct the corners and sides of an image projected on a curved
surface with right angles.
Execution Method
s Settings > Geometry Correction > Corner Wall
Point Correction
This feature divides the projected image into a grid and corrects the distortion
in 0.5 pixel increments by moving the selected point of intersection from side
to side and up and down.
Execution Method
gg Related Links
• "Focus/Distortion" p.61
• "Color Mode" p.61
• "Image Enhancement" p.62
• "Gamma" p.62
• "RGBCMY" p.62
• "Brightness Settings" p.62
Focus/Distortion
You can correct the focus and the image distortion.
If you installed an optional short throw lens, correct the focus at the center of
your screen first, and then correct any distortion in the surrounding area.
When you focus on the center of your screen, the surrounding area may be
distorted and out of focus.
Execution Method
• Press the [Focus] button on the remote control until the focus adjustment
screen or the distortion adjustment screen is displayed..
• Press the [Lens] button on the control panel until the focus adjustment
screen or the distortion adjustment screen is displayed.
• Use the arrow buttons on the control panel or remote control to correct the
focus or the distortion.
s Settings > Geometry Correction > Point Correction
Adjusting the Image Quality
This section provides instructions to adjust the quality of your image.
Color Mode
The projector offers different color modes to provide optimum brightness,
contrast, and color for a variety of viewing environments and image types.
You can select the mode designed to match your image and environment, or
experiment with the available modes.
Execution Method
Page 62
Using Basic Projector Features
62
• Press the [Color Mode] button on the remote control.
• Change the projector's menu:
s Image > Color Mode
Image Enhancement
You can adjust the resolution of the image to reproduce a clear image with an
emphatic texture and material feel.
Execution Method
s Image > Image Enhancement
Gamma
You can adjust the halftone brightness by selecting one of the gamma
correction values, or referring to a gamma graph.
RGBCMY
You can adjust the Hue, Saturation, and Brightness of each color R (red), G
(green), B (blue), C (cyan), M (magenta), Y (yellow) individually.
Execution Method
s Image > Advanced > RGBCMY
Brightness Settings
You can select the brightness for the light source.
Execution Method
s Image > Advanced > Gamma
Execution Method
s Settings > Brightness Settings
Using Multiple Projectors
You can combine the projected images from two or more projectors to create
one unified image area.
gg Related Links
• "Tiling" p.63
Page 63
Using Basic Projector Features
63
• "Edge Blending" p.63
• "Black Level" p.63
• "Scale" p.63
• "Color Matching" p.64
• "Simple Stacking" p.64
Tiling
You can assign a projection position to each projector.
Execution Method
s Extended > Multi-Projection > Edge Blending
Black Level
You can adjust the brightness and color tone of the areas where the images do
not overlap to create a seamless image.
Execution Method
s Extended > Multi-Projection > Black Level
Scale
You can use the Scale feature to crop and combine them into one unified
image area.
Execution Method
s Extended > Multi-Projection > Tiling
Edge Blending
You can use the Edge Blending feature to create a seamless image from
multiple projectors.
Page 64
Using Basic Projector Features
64
Execution Method
s Extended > Multi-Projection > Scale
Color Matching
You can match the display quality of multiple projectors that will project next
to each other.
Execution Method
s Extended > Multi-Projection > Screen Matching > Color Matching
Simple Stacking
You can easily and quickly create a bright projected image by overlapping the
images of two projectors.
Execution Method
s Extended > Multi-Projection > Simple Stacking
Maintaining the Projector Quality
This section provides information about maintaining the quality of projected
images.
gg Related Links
• "Panel Alignment" p.65
• "Color Uniformity" p.65
• "Refresh Mode" p.65
Page 65
Using Basic Projector Features
65
• "Light Source Calibration" p.65
Panel Alignment
You can adjust the pixel color shift for the LCD panel. You can adjust the
pixels horizontally and vertically in 0.125 pixels increments within a range of
±3 pixels.
Execution Method
s Extended > Display > Panel Alignment
Color Uniformity
If the color tone of the image is uneven, you can adjust the color tone balance.
Light Source Calibration
The light source calibration process optimizes the color balance of the
currently projected image.
Execution Method
s Reset > Light Source Calibration
Managing the Projector's Settings
This section provides information about managing the projector's settings.
gg Related Links
• "Memory" p.65
• "Schedule Settings" p.65
• "Button Lock" p.66
• "Lens Lock" p.67
• "Password Protection" p.67
Memory
You can save customized settings and then select the saved settings whenever
you want to use them.
Execution Method
s Extended > Display > Color Uniformity
Refresh Mode
The refresh mode process clears any projected afterimage and turns off the
projector after a specified period of time.
Execution Method
s Reset > Refresh Mode
Execution Method
• Press the [Memory] button on the remote control.
• Change the projector's menu:
s Settings > Memory
Schedule Settings
You can schedule up to 30 events to occur automatically on your projector,
such as turning the projector on or off or switching the input source. The
projector performs the selected events on the specified date and time in the
schedule you set up.
Execution Method
Page 66
Using Basic Projector Features
66
s Extended > Schedule Settings
Button Lock
Button lock security to block operation of the projector using the buttons on
the control panel or remote control.
Even if you can lock the buttons on the control panel, you can still use the
remote control as usual.
The remote control buttons lock feature locks the following buttons.
Execution Method
• To lock the control panel buttons, hold down the control panel lock button
on the control panel.
To unlock the control panel buttons, hold down the [Enter] button on the
control panel for approximately 7 seconds.
• To lock the remote control buttons, hold down the [Home] button on the
remote control for approximately 5 seconds.
To unlock the remote control buttons, hold down the [Home] button again
for approximately 5 seconds.
Page 67
Using Basic Projector Features
67
Lens Lock
You can disable [Lens Shift], [Zoom], and [Focus] button operations on the
remote control.
Execution Method
s Settings > Lock Setting > Lens Lock
Password Protection
Password security to prevent people who do not know the password from
using the projector, and prevent changes to the startup screen and other
settings.
You can set up the following types of password security using one shared
password:
• Power On Protection prevents anyone from using the projector without
first entering a password. When plugging the power cord and turning on
the projector at first time, you must enter the correct password. This also
applies to Direct Power On and Auto Power On.
• User's Logo Protection prevents anyone from changing the custom screen
displayed when the projector turns on, when no signal is being input, or
when you use the A/V Mute feature. The custom screen discourages theft by
identifying the projector's owner.
• Network Protection prevents anyone from changing the projector's
Network settings.
• Schedule Protection prevents anyone from changing the projector's
schedule settings.
• Remote Camera Access prevents anyone from using the Remote Camera
Access function.
Execution Method
Hold the [Freeze] button on the remote control for approximately 5 seconds.
You can set a four-digit password. Hold down the [Num] button on
a
the remote control and use the numeric buttons to set a password. The
default password is set to "0000".
Attention
• If an incorrect password is entered three times in succession, the message "The
projector's operation will be locked." is displayed for approximately 5 minutes,
and the projector switches to standby mode. If this happens, disconnect the
power plug from the electrical outlet, reinsert it, and turn the projector back on.
The projector displays the password entry screen again so that you can enter the
correct password.
• If you have forgotten the password, make a note of the "Request Code: xxxxx"
number that appears on the screen and contact Epson for help.
• If you continue to repeat the above operation and input the wrong password 30
times in succession, the message "The projector's operation will be locked.
Contact Epson as described in your documentation." is displayed and the
projector does not accept any more password entries. Contact Epson for help.
Page 68
Copying Menu Settings Between Projectors (Batch Setup)
68
After selecting the projector's menu settings for one projector, you can use the
following methods to copy the settings to other projectors, as long as they are
the same model.
• by using a USB flash drive
• by connecting a computer and projector using a USB cable
• by using Epson Projector Management
You cannot copy any information unique to an individual projector, such as
Light Source Hours or Status.
• Perform batch setup before adjusting the image settings such as
a
keystone distortion correction. Since image adjustment values are
also copied to another projector, the adjustments you made before
performing the batch setup are overwritten and the projected screen
you adjusted may change.
• When copying the menu settings from one projector to another,
user's logo is also copied. Do not register the information that you do
not want to share between multiple projectors as a user's logo.
• Make sure Batch Setup Range is set to Limited if you do not want to
copy the following settings:
• Password Protection settings
• EDID in the Signal menu
• Network menu settings (except for the Notifications menu and
the Others menu)
Transferring Settings From a USB Flash Drive
You can copy menu settings from one projector to another of the same model
using a USB flash drive.
The USB flash drive must use a FAT format and not incorporate any
a
a
b
c
d
security function. Delete any files on the drive before using it for batch
setup or the settings may not be saved correctly.
Disconnect the power cord from the projector, and check that all of the
projector's indicators have turned off.
Connect an empty USB flash drive directly to the projector's USB-A
port.
Hold down the [Esc] button on the remote control or the control panel
and connect the power cord to the projector.
When all of the projector's indicators other than the WLAN (wireless
LAN) indicator turn on, release the [Esc] button.
The indicators start flashing and the batch setup file is written to the
USB flash drive. When writing is finished, the projector turns off.
Caution
Epson takes no responsibility for batch setup failures and associated repair costs
due to power outages, communication errors, or other problems that may cause
such failures.
gg Related Links
• "Transferring Settings From a USB Flash Drive" p.68
• "Transferring Settings From a Computer" p.69
• "Batch Setup Error Notification" p.70
Caution
Do not disconnect the power cord or the USB flash drive from the projector
while the file is being written. If the power cord or USB flash drive is
disconnected, the projector may not start correctly.
Remove the USB flash drive.
e
The file name for the batch setup file is PJCONFDATA.bin. If
a
you need to change the file name, add text after PJCONFDATA
using only alphanumeric characters. If you change the
PJCONFDATA section of the file name, the projector may not be
able to recognize the file correctly.
Page 69
Copying Menu Settings Between Projectors (Batch Setup)
69
Disconnect the power cord from the projector to which you want to
f
copy settings, and check that all of the projector's indicators have
turned off.
Connect the USB flash drive containing the saved batch setup file to the
g
projector's USB-A port.
Hold down the [Menu] button on the remote control or the control
h
panel and connect the power cord to the projector.
When all of the projector's indicators other than the WLAN (wireless
i
LAN) indicator turn on, release the [Menu] button. (The indicators
remain on for approximately 75 seconds.)
When all of the indicators start flashing, the settings are being written.
When writing is finished, the projector turns off.
Caution
Do not disconnect the power cord or the USB flash drive from the projector
while the file is being written. If the power cord or USB flash drive is
disconnected, the projector may not start correctly.
Remove the USB flash drive.
j
Connect a USB cable to the computer's USB port and to the projector's
b
Service port.
Hold down the [Esc] button on the remote control or the control panel
c
and connect the power cord to the projector.
When all of the projector's indicators other than the WLAN (wireless
d
LAN) indicator turn on, release the [Esc] button.
The computer recognizes the projector as a removable disk.
Open the removable disk icon or folder, and save the batch setup file to
e
the computer.
The file name for the batch setup file is PJCONFDATA.bin. If
a
Eject the USB device (Windows) or drag the removable disk icon to the
f
Trash (Mac).
Disconnect the USB cable.
g
The projector turns off.
you need to change the file name, add text after PJCONFDATA
using only alphanumeric characters. If you change the
PJCONFDATA section of the file name, the projector may not be
able to recognize the file correctly.
Transferring Settings From a Computer
You can copy menu settings from one projector to another of the same model
by connecting the computer and projector with a USB cable.
You can use this batch setup method with the following operating
a
a
system versions:
• Windows 8.1 and later
• macOS 10.13.x and later
Disconnect the power cord from the projector, and check that all of the
projector's indicators have turned off.
Disconnect the power cord from the projector to which you want to
h
copy settings, and check that all of the projector's indicators have
turned off.
Connect the USB cable to the computer's USB port and to the
i
projector's Service port.
Hold down the [Menu] button on the remote control or the control
j
panel and connect the power cord to the projector.
Page 70
Copying Menu Settings Between Projectors (Batch Setup)
70
When all of the projector's indicators other than the WLAN (wireless
k
LAN) indicator turn on, release the [Menu] button.
The computer recognizes the projector as a removable disk.
Copy the batch setup file (PJCONFDATA.bin) that you saved to your
l
computer to the top level folder of the removable disk.
Do not copy any files or folders other than the batch setup file to
a
Eject the USB device (Windows) or drag the removable disk icon to the
m
Trash (Mac).
Disconnect the USB cable.
n
When all of the indicators start flashing, the settings are being written.
When writing is finished, the projector turns off.
the removable disk.
Caution
Do not disconnect the power cord from the projector while the file is being
written. If the power cord is disconnected, the projector may not start
correctly.
Indicator status Problem and solutions
• Power: Blue - flashing
fast
• Status: Blue - flashing
fast
• Laser: Orange - flashing
fast
• Temp: Orange - flashing
fast
Writing the settings may have failed and an error may
have occurred in the projector's firmware.
Stop using the projector, remove the power plug from
the electrical outlet. Contact Epson for help.
Batch Setup Error Notification
The projector's indicators notify you if an error occurs during a batch setup
operation. Check the status of the projector's indicators and follow the
instructions described in the table here.
Indicator status Problem and solutions
• Laser: Orange - flashing
fast
• Temp: Orange - flashing
fast
The batch setup file may be corrupt, or the USB flash
drive may not be connected correctly.
Disconnect the USB flash drive, unplug and then plug
in the projector's power cord, and then try again.
Page 71
Menu Settings
Refer to these sections to learn more about your projector's settings.
gg Related Links
• "Image Menu" p.72
• "Signal Menu" p.78
• "Settings Menu" p.82
• "Extended Menu" p.93
• "Network Menu" p.107
• "Info Menu" p.117
• "Reset Menu" p.120
Page 72
Image Menu
72
Settings on the Image menu let you adjust the quality of your image. The
available settings depend on the currently selected color mode and input
source. The settings are saved separately for each selected color mode.
gg Related Links
• "Color Mode" p.72
• "Brightness" p.72
• "Contrast" p.73
• "Color Saturation" p.73
• "Tint" p.73
• "Sharpness" p.73
• "White Balance" p.73
• "4K Enhancement" p.73
• "Image Preset Mode" p.74
• "Frame Interpolation" p.74
• "Deinterlacing" p.74
• "Noise Reduction" p.75
• "MPEG Noise Reduction" p.75
• "Super-resolution" p.75
• "Detail Enhancement" p.75
• "Reset (Image Enhancement)" p.75
• "Scene Adaptive Gamma" p.76
• "Gamma" p.76
• "RGBCMY" p.76
• "Dynamic Contrast" p.76
• "Lights-Out Control" p.77
• "Reset (Image menu)" p.77
Dynamic
This is the brightest mode. Ideal for use in a bright room.
Presentation
The images are vivid and brought to life. Ideal for making presentations or
watching a TV program in a bright room.
Natural
Reproduces colors faithfully. Ideal for projecting still pictures such as
photos.
Cinema
Gives images a natural tone. Ideal for watching films in a dark room.
BT.709
Produces images that conform to the ITU-R BT.709.
DICOM SIM
This produces images with clear shadows. Ideal for projecting X-ray
photographs and other medical images. The projector is not a medical
device and cannot be used for medical diagnosis.
Multi-Projection
Minimize the color tone difference between each projected image. Ideal for
projecting from multiple projectors.
You can also change the projector's Color Mode using the [Color
a
Mode] button on the remote control.
Brightness
Color Mode
s Image > Color Mode
s Extended > Multi-Projection > Screen Matching > Color Mode
You can adjust the vividness of image colors for various image types and
environments. The brightness of the image varies depending on the mode
selected.
s Image > Brightness
You can lighten or darken the overall image.
This setting does not affect light source brightness. To change the light
a
source brightness, select Light Source Mode in the Settings menu.
s Settings > Brightness Settings > Light Source Mode
Page 73
Image Menu
73
Contrast
s Image > Contrast
You can adjust the difference between light and dark areas of the image.
Color Saturation
s Image > Color Saturation
You can adjust the intensity of the image colors.
Tint
s Image > Tint
You can adjust the balance of green to magenta tones in the image.
Sharpness
s Image > Sharpness
You can adjust the sharpness or softness of image details.
Standard
You can adjust the image sharpness so that it is sufficiently balanced.
Thin Line Enhancement
Higher values enhance the details such as hair or fabric patterns.
Thick Line Enhancement
Higher values enhance the outline, background, and the other main parts
of the objects in the image to show them clearly.
White Balance
s Image > White Balance
You can adjust the overall tint of the image.
Color Temp.
You can adjust the overall tint of the image within a range from 3200K to
10000K. Higher values tint the image blue and lower values tint the image
red.
When Color Mode is set to Dynamic, the set Color Temp. may differ from
the actual Color Temp. of the light from the projector. Use this menu as a
guide.
G-M Correction
Higher values tint the image green and lower values tint the image red.
Offset R/Offset G/Offset B/Gain R/Gain G/Gain B
You can adjust the individual R (red), G (green), and B (blue) components
of the offset and gain.
4K Enhancement
s Image > Image Enhancement > 4K Enhancement
You can project an image at a doubled resolution by diagonally shifting 1
pixel in increments of 0.5 pixels. A high-resolution image signal is projected
in fine detail.
Off
If a signal that exceeds the panel resolution of this projector is input, the
image is displayed according to the panel resolution of this projector.
Full HD
For a signal with a resolution of 1080i/1080p/WUXGA or higher.
WUXGA+
For a signal with a resolution that exceeds WUXGA. When projecting a
high-resolution movie, you can project a high-definition image by using
this setting with Image Preset Mode.
Page 74
Image Menu
74
• You cannot select this setting when the Aspect setting is set to
a
Native in the projector's Signal menu.
• When projecting from multiple projectors, select Off to unify each
image.
• Off is ideal for projecting presentation materials from computers and
so on.
• If you select Full HD or WUXGA+, the status corrected using the
following function is canceled.
• Edge Blending
• Scale
• Curved Surface
• Point Correction
• Corner Wall
• E-Zoom
• Split Screen
• Frame Interpolation
• Noise Reduction
• MPEG Noise Reduction
When you change the 4K Enhancement setting to Off, the settings
return to their previous state.
Image Preset Mode
s Image > Image Enhancement > Image Preset Mode
• To minimize delays, select Off.
a
• If you select Off, you cannot set the other items in the Image
Enhancement setting.
• After selecting Preset 1 to Preset 5, you can fine tune each setting
individually. The settings value in the preset option are overwritten.
• The settings value are overwritten separately when 4K Enhancement
is enabled and disabled.
Frame Interpolation
s Image > Image Enhancement > Frame Interpolation
You can play fast moving images smoothly by producing intermediate frames
between the original frames.
If your resulting images contain noise, set to Off.
• You cannot select this setting in the following cases.
a
• 4K Enhancement is enabled.
• A signal with a resolution that exceeds WUXGA is input.
• Aspect is set to V-Zoom.
• Scale is set to Auto or Manual.
• Edge Blending is set to Blending/Black Level or Black Level.
• Image Preset Mode is set to Off.
• While performing E-Zoom
You can set the Image Enhancement options as a batch using preset values.
The following settings are saved in the preset options.
• Frame Interpolation
• Deinterlacing
• Noise Reduction
• MPEG Noise Reduction
• Super-resolution
• Detail Enhancement
Deinterlacing
s Image > Image Enhancement > Deinterlacing
You can set whether or not to convert interlaced-to-progressive signals for
certain video image types.
Off
For fast-moving video images.
Page 75
Image Menu
75
Video
For most video images.
Film/Auto
For movies, computer graphics, and animation.
Setting is only displayed in the following cases.
a
• The current signal is interlaced signal (480i/576i/1080i).
• Image Preset Mode is enabled.
Noise Reduction
s Image > Image Enhancement > Noise Reduction
You can reduce flickering in images when inputting progressive signals or
progressive interlace signals.
• You cannot select this setting in the following cases.
a
• 4K Enhancement is enabled.
• A signal with a resolution that exceeds WUXGA is input.
• Image Preset Mode is set to Off.
Super-resolution
s Image > Image Enhancement > Super-resolution
You can reduce blurring when projecting low resolution images.
Fine Line Adjust
Higher values enhance details such as hair or fabric patterns.
Soft Focus Detail
Higher values enhance the outline, background, and the other main parts
of the objects in the image to show them clearly.
You cannot select this setting when the Image Preset Mode setting is
a
set to Off.
Detail Enhancement
s Image > Image Enhancement > Detail Enhancement
You can create a more emphatic texture and material feel of the image.
Strength
Higher values enhance the contrast.
MPEG Noise Reduction
s Image > Image Enhancement > MPEG Noise Reduction
You can reduce the noise or artifacts seen in MPEG video.
• You cannot select this setting in the following cases.
a
• 4K Enhancement is enabled.
• A signal with a resolution that exceeds WUXGA is input.
• Image Preset Mode is set to Off.
Range
Higher values widen the range of detailed enhancement.
• Depending on the image, a highlight may be noticeable at the border
a
between colors. If this bothers you, set a smaller value.
• You cannot select this setting when the Image Preset Mode setting is
set to Off.
Reset (Image Enhancement)
s Image > Image Enhancement > Reset
Page 76
Image Menu
76
You can reset the settings on the Image Enhancement setting to their default
preset settings.
You cannot select this setting when the Image Preset Mode setting is
a
set to Off.
Scene Adaptive Gamma
s Image > Advanced > Scene Adaptive Gamma
You can adjust the coloring according to the scene and obtain a more vivid
image.
Higher values enhance the more the contrast.
Gamma
s Image > Advanced > Gamma
You can adjust the coloring by selecting one of the gamma correction values,
or referring to a gamma graph. If you want to make finer adjustments, select
Customized.
When you select a smaller value, you can reduce the overall brightness of the
image to make the image sharper. When you select a larger value, the dark
areas of images become brighter, but the color saturation for lighter areas may
become weaker.
• Project a still picture to adjust the Gamma. You cannot adjust the
a
Gamma correctly when projecting movies.
• If you set the Color Mode setting to DICOM SIM in the projector's
Image menu, select the adjustment value according to the projection
size.
• If the projection size is 120 inches or less, select a small value.
• If the projection size is 120 inches or more, select a large value.
• Medical images may not be reproduced correctly depending on your
settings and screen specifications.
RGBCMY
s Image > Advanced > RGBCMY
You can adjust the Hue, Saturation, and Brightness of each color R (red), G
(green), B (blue), C (cyan), M (magenta), Y (yellow) individually.
Dynamic Contrast
s Image > Dynamic Contrast
You can adjust the projected luminance based on the image brightness.
Dynamic Contrast
Set to On to automatically adjust the amount of light.
Response Speed
Select High Speed to adjust the amount of light as soon as the scene
changes.
Black Level
Set the black level when the brightness level of the image signal is zero.
When you select 0%, the light source turns off.
Page 77
Image Menu
Lights-Out Control
s Image > Lights-Out Control
You can set the light source to turn off automatically.
Lights-Out Control
Set to On to automatically turn off the light source when the signal level
falls below the reference level for a set period of time.
Lights-Out Signal Level
Set the brightness level for the video signal being controlled. After turning
off automatically, it turns on immediately when exceeding the specified
image level.
Lights-Out Timer
Set the amount of time before automatically turning off the light source.
Reset (Image menu)
77
s Image > Reset
You can reset all adjustment values on the Image menu to their default
settings.
Page 78
Signal Menu
78
Normally, the projector automatically detects and optimizes the input signal
settings. If you need to customize the settings, you can use the Signal menu.
The available settings depend on the currently selected input source. The
settings are saved separately for each selected input source.
gg Related Links
• "Resolution" p.78
• "Aspect" p.78
• "Tracking" p.79
• "Sync." p.79
• "Position" p.79
• "Auto Setup" p.79
• "Overscan" p.80
• "Blanking" p.80
• "Color Space" p.80
• "Dynamic Range" p.80
• "Video Range" p.80
• "EDID" p.81
• "Scale" p.81
• "Reset (Signal menu)" p.81
Resolution
s Signal > Resolution
You can set the input signal resolution.
Auto
Select to automatically identify the resolution of the input signal.
If not detected automatically using the Auto option, select the following
options.
Wide
For wide screens.
Normal
For 4:3 or 5:4 screens depending on the connected computer.
Manual
You can specify the resolution. This is ideal when connected computer is
fixed.
Setting is only displayed when the current source is Computer.
a
Aspect
s Signal > Aspect
The projector can display images in different width-to-height ratios called
aspect ratios. Normally, the input signal from your video source determines
the image's aspect ratio. However, for certain images you can change the
aspect ratio to fit your screen.
Auto
Automatically sets the aspect ratio according to the input signal and the
Resolution setting.
Normal
Displays images using the full projection area and maintains the aspect
ratio of the image.
4:3
Converts the aspect ratio of the image to 4:3.
16:9
Converts the aspect ratio of the image to 16:9.
Full
Displays images using the full size of the projection area, but does not
maintain the aspect ratio.
H-Zoom/V-Zoom
Displays images using the full width (H-Zoom) or full height (V-Zoom) of
the projection area and maintains the aspect ratio of the image. Areas that
exceed the edges of the projected screen are not projected.
Page 79
Signal Menu
79
Native
Displays images as is (aspect ratio and resolution are maintained). Areas
that exceed the edges of the projected screen are not projected.
• Available only when the current source is set to one of the following:
a
• Computer
• HDMI
• DVI-D
• HDBaseT
• SDI (EB‑PU2220B)
• Available only when the Scale setting is set to Off or the Scale Mode
setting is set to Full Display.
s Signal > Scale > Scale Mode
• Set the Screen Type setting in the projector's Extended menu before
changing the aspect ratio.
s Extended > Display > Screen > Screen Type
• To display images without black bars, set Resolution to Wide or
Normal in the projector’s Signal menu according to the computer’s
resolution.
• The available aspect ratio setting varies depending on the selected
Screen Type setting and the input signal from your image source.
• Note that using the aspect ratio function of the projector to reduce,
enlarge, or split the projected image for commercial purposes or for
public viewing may infringe upon the rights of the copyright holder
of that image based on copyright law.
• If there are margins between the edge of the image and the projected
screen frame, you can adjust the position of the image using the
Screen Position setting in the projector's Extended menu.
s Extended > Display > Screen > Screen Position
• You can change the projector's Aspect using the [Aspect] button on
the remote control.
Setting is only displayed when the current source is Computer.
a
Sync.
s Signal > Sync.
You can adjust the signal to eliminate fuzziness or flickering in computer
images.
Setting is only displayed when the current source is Computer.
a
Position
s Signal > Position
You can adjust the image location on the screen.
Setting is only displayed when the current source is Computer.
a
Auto Setup
s Signal > Auto Setup
Tracking
s Signal > Tracking
You can adjust the signal to eliminate vertical stripes in computer images.
Set to On to automatically optimize computer image quality.
Setting is only displayed when the current source is Computer.
a
Page 80
Signal Menu
80
Overscan
s Signal > Overscan
You can change the projected image ratio to make the edges visible by a
selectable percentage or automatically.
Available only when the current source is set to one of the following:
a
• HDMI
• DVI-D
• HDBaseT
• SDI (EB‑PU2220B)
Blanking
s Signal > Blanking
You can hide images in the specified area.
Use the arrow buttons on the control panel or remote control to adjust the
area. You can hide up to half of the projected image in each direction (except
for one pixel).
Setting is only displayed when the Content Playback setting is set to
a
Off in the projector's Settings menu.
Setting is only displayed in the following cases.
a
• The current source is HDMI, HDBaseT, or SDI (EB‑PU2220B).
• Color Mode is set to other than BT.709 or DICOM SIM.
Dynamic Range
s Signal > Dynamic Range
You can set the video range to match the setting of input source.
Select Auto to automatically identify the dynamic range of the input signal.
The result for your selected setting is displayed as Signal Status.
HDR10 Setting
You can adjust the PQ curve of the dynamic range in the HDR PQ
(Perceptual Quantizer) method.
HLG Setting
You can adjust the HLG curve of the dynamic range in the HDR HLG
(Hybrid Log Gamma) method.
• Setting is only displayed in the following cases.
a
• The current source is HDMI, HDBaseT, or SDI (EB‑PU2220B).
• Color Mode is set to other than BT.709 or DICOM SIM.
• HDR10 Setting is only available when Signal Status is set to
HDR10, or Dynamic Range is set to HDR10.
• HLG Setting is only available when Signal Status is set to HLG, or
Dynamic Range is set to HLG.
Color Space
s Signal > Color Space
You can switch the color space that can handle the color information of the
input image.
Select Auto to apply a suitable color space for the AVI InfoFrame of the
image.
Video Range
s Signal > Advanced > Video Range
You can set the video range to match the setting of input source from the
HDMI, DVI-D, or HDBaseT port.
Page 81
Signal Menu
81
Limited (16-235)
For the color tone range 16 to 235.
Full (0-255)
For the color tone range 0 to 255.
EDID
s Signal > Advanced > EDID
Even if you setup multiple displays with different resolutions, you can set the
same EDID as the standard display and switch the EDID of the current source
to unify the EDID across the displays.
Preset EDID
You can set the EDID options as a batch using preset values.
The following settings are saved in the preset options.
• Resolution
• Refresh Rate
• Color Depth
You can change the preset settings if necessary.
Scale
When set to Auto, the clip position is set automatically depending on the
Edge Blending and Tiling settings. After selecting Auto, you can fine tune
manually.
Select Manual to adjust the clip range and position manually.
Scale Mode
Select how to change the magnification.
• Zoom Display to maintain the image position and aspect ratio.
• Full Display to adjust the image according to the image position and
aspect ratio.
Scale Horizontally/Scale Vertically
You can adjust the magnification horizontally and vertically in 0.01x
increments, and enlarge or reduce the image. (Minimum magnification of
0.5 to maximum magnification of 10.)
Clip Adjustment
Use the arrow buttons to adjust the coordinates and size of each image as
you view the screen.
Clip Range
You can view the clipped area you selected.
• Setting is only displayed when the current source is HDMI,
a
HDBaseT, or DVI-D.
• Select Reset to reset all adjustment values for EDID to their default
values.
Scale
s Signal > Scale
s Extended > Multi-Projection > Scale
You can enlarge or reduce the image in the vertical and horizontal directions.
When using multiple projectors to project one image, you can adjust the scale
of the image displayed by each projector.
Reset (Signal menu)
s Signal > Reset
You can reset all adjustment values on the Signal menu to their default
settings, except for the following:
• EDID
Page 82
Settings Menu
82
Options on the Settings menu let you customize various projector features.
gg Related Links
• "Geometry Correction" p.82
• "Split Screen" p.83
• "Volume" p.84
• "HDMI Link" p.84
• "Control Panel Lock" p.84
• "Lens Lock" p.85
• "Light Source Mode" p.85
• "Brightness Level" p.85
• "Constant Brightness" p.85
• "Estimated Remains" p.86
• "Energy Saving Mode" p.87
• "Remote Receiver" p.87
• "User Button" p.88
• "Test Pattern" p.88
• "Memory" p.88
• "Content Playback" p.89
• "NFC Settings" p.91
• "Reset (Settings menu)" p.91
Geometry Correction
H/V-Keystone
Manually corrects distortion in the horizontal and vertical directions
independently. If the image aspect is incorrect, adjust the image balance by
using V-Balance and H-Balance.
You cannot combine with other correction methods.
Quick Corner
Corrects each of the four corners of the projected image independently.
Curved Surface
Corrects the corners and sides of an image projected on a curved surface
with the same radius.
• Move the lens position to the home position.
a
Corner Wall
Corrects the corners and sides of an image projected on a curved surface
with right angles.
• If a large amount of adjustment is performed, the focus may not
be uniform even after making adjustments.
• If you set the Maintain Aspect Ratio setting to On after
correcting the corrections may not be applied. Reset the
corrections to their default values or reduce the amount of
correction, and try it again.
• If you change the standard line during correcting, the present
settings are reset.
s Settings > Geometry Correction
s Extended > Multi-Projection > Geometry Correction
s Extended > Multi-Projection > Simple Stacking > Point Correction
You can adjust image shape to rectangular. After correction, your image is
slightly smaller.
You can check the available adjustment range in the projector's Specifications.
Off
Temporarily cancels geometry correction. Even when set to Off, the
correction values are saved.
• Move the lens position to the home position.
a
Point Correction
Divides the projected image into a grid and corrects the distortion in 0.5
pixel increments by moving the selected point of intersection in any
direction. You can move the points on the grid between 0.5 to 600 pixels in
any direction, including outside the projection range.
• If a large amount of adjustment is performed, the focus may not
be uniform even after making adjustments.
• We recommend you adjust the image shape based on the point
nearest to the center of the screen.
Page 83
Settings Menu
83
Memory
You can save the shape of an image you have adjusted and load it when
needed.
• You can also open the Geometry Correction screen using the
a
[Geometry] button on the control panel or remote control.
• You can also open the Memory screen using the [Memory] button
on the remote control.
Split Screen
s Settings > Split Screen
You can simultaneously project two images from different image sources.
Screen Size
Select the screen size.
Depending on the video signals that are input, the images on the left
a
Source
Select the input source.
a
Swap Screens
You can swap images that are being projected on the left and right.
and right may not appear to be the same size even if you select
Equal.
• The following input source combinations cannot be projected on
a split screen.
• Computer and LAN
• DVI-D and HDMI
• Computer and SDI (EB‑PU2220B)
• LAN and SDI (EB‑PU2220B)
• Input signals with a horizontal resolution exceeding 1920 are not
supported.
Audio Source
Select the screen from which you want to hear audio.
When you select Auto, audio is output from the enlarged screen. If the
screen size is set to Equal, audio is output from the screen on the left.
• While using the split screen feature, other projector features may not
a
gg Related Links
• "Split Screen Projection Restrictions" p.83
be available and some settings may be automatically applied to all
images.
• You cannot perform split screen projection when the Content
Playback setting is set to On in the projector's Settings menu.
• You can also open the Split Screen Setup screen using the [Split]
button on the remote control.
Split Screen Projection Restrictions
Operating restrictions
The following operations cannot be performed during split screen projection.
• Setting the projector's menu
• E-Zoom
• Switching the aspect mode (the aspect mode is set to Normal)
• Operations using the [User] button on the remote control
Image restrictions
• If you make adjustments such as Brightness, Contrast, Color Saturation,
Tint, and Sharpness in the projector's Image menu, you can apply them
only to the image on the left. Default adjustments are applied to the image
on the right. Adjustments that affect the entire projected image such as
Color Mode and Color Temp. are applied for both left and right images.
• Even if you make adjustments for Noise Reduction and Deinterlacing in
the projector's Image menu, Noise Reduction is set to 0 and Deinterlacing
is set to Off for the image on the right.
s Image > Image Enhancement > Noise Reduction
Page 84
Settings Menu
84
• Even if you set Display Background to Logo in the projector's Extended
menu, the blue screen appears when no image signal is being input.
Volume
s Settings > Volume
You can adjust the volume of the speaker connected to the projector's Audio
Out port.
Caution
Do not start a presentation at a high volume setting. Sudden loud noises may cause
hearing loss.
Always lower the volume before powering off, so that you can power on and then
gradually increase the volume.
HDMI Link
s Settings > HDMI Link
You can adjust the HDMI Link options that allow the projector remote to
control HDMI-connected devices.
Device Connections
The devices connected to the HDMI ports are listed.
HDMI Link
Set to On to enable the HDMI Link features.
Audio Out Device
To output audio from the speaker connected to the projector's Audio Out
port, select Projector. When an audio/video system is connected to the
projector and you want to output audio from it, select AV System. When
an audio/video system is not connected to the projector, audio is output
from the speaker connected to the Audio Out port even if Audio Out
Device is set to AV System.
Power On Link
You can control what happens when you turn on the projector or
connected device.
• Bidirectional: automatically turns on the connected device when you
turn on the projector, and vice versa.
• Device -> PJ: automatically turns on the projector when you turn on the
connected device.
• PJ -> Device: automatically turns on the connected device when you
turn on the projector.
Power Off Link
You can control whether connected devices are turned off when you turn
off the projector.
Link Buffer
You can improve the performance of the linked operations by changing
the settings if the HDMI Link function is not working correctly.
Set the HDMI Link setting to On first to adjust the options.
a
Control Panel Lock
s Settings > Lock Setting > Control Panel Lock
You can control projector button locking to secure the projector.
Full Lock
All buttons locked.
Partial Lock
All buttons except for the [On] button and the [Standby] button locked.
Off
No buttons locked.
Page 85
Settings Menu
85
• You can control projector button locking using the control panel
a
lock button on the control panel.
• To unlock the buttons, hold down the [Enter] button on the control
panel for approximately 7 seconds. A message is displayed and the
lock is released.
Lens Lock
s Settings > Lock Setting > Lens Lock
You can disable [Lens Shift], [Zoom], and [Focus] button operations on the
remote control.
Light Source Mode
s Settings > Brightness Settings > Light Source Mode
s Extended > Multi-Projection > Screen Matching > Brightness Settings >
Light Source Mode
You can select the brightness for the light source.
Normal
Maximum brightness. This makes the light source operation time
approximately 20,000 hours.
Quiet
70% brightness with reduced fan noise. This makes the light source
operation time approximately 20,000 hours.
Extended
70% brightness and extends the life expectancy of the light source. This
makes the light source operation time approximately 30,000 hours.
Custom
You can select a custom brightness level.
Setting is only displayed when Constant Brightness is set to Off.
a
Brightness Level
s Settings > Brightness Settings > Brightness Level
s Extended > Multi-Projection > Screen Matching > Brightness Settings >
Brightness Level
You can select the Custom brightness level you want.
Setting is only displayed when Light Source Mode is set to Custom.
a
Constant Brightness
s Settings > Brightness Settings > Constant Brightness
s Extended > Multi-Projection > Screen Matching > Brightness Settings >
Constant Brightness
You can maintain the brightness of the light source set in the Brightness
Level setting.
• Setting is only displayed when Light Source Mode is set to Custom.
a
• When set to On, you cannot change the settings for Light Source
Mode and Brightness Level.
• When set to Off, the Brightness Level setting changes according to
the status of the light source.
• When you use this function, we recommend setting Energy Saving
Mode to Off.
s Settings > Brightness Settings > Energy Saving Mode
Page 86
Settings Menu
86
Estimated Remains
s Settings > Brightness Settings > Estimated Remains
s Extended > Multi-Projection > Screen Matching > Brightness Settings >
Estimated Remains
You can check how long the projector can maintain constant brightness.
Setting is only displayed when Constant Brightness is set to On.
a
gg Related Links
• "Constant Brightness Usage Hours" p.86
• "Light Source Operation Time" p.86
Constant Brightness Usage Hours
If you turn on Constant Brightness, the number of hours the projector can
maintain constant brightness is displayed as Estimated Remains.
Display level Estimated remaining hours
10,000 or more hours
8,000 to 9,999 hours
6,000 to 7,999 hours
4,000 to 5,999 hours
2,000 to 3,999 hours
0 to 1,999 hours
The number of hours displayed as Estimated Remains is just a guide.
a
Light Source Operation Time
The light source operation time varies depending on the Brightness Level
setting and whether Constant Brightness is on or off.
• The light source operation time varies depending on the
a
environmental conditions and usage.
• The hours listed here are an approximate and are not guaranteed.
• You may need to replace internal parts sooner than the estimated
light source operation time.
• If Constant Brightness is turned on, and you have exceeded the
usage hours listed here, you may not be able to select a high
Brightness Level setting.
Page 87
Settings Menu
87
Constant Brightness off
Brightness Level setting Time before the brightness of the light source is
reduced by half (approximate)
100% 20,000 hours
90% 21,000 hours
80% 24,000 hours
70% 30,000 hours
60% 37,000 hours
50% 47,000 hours
40% 61,000 hours
30% or less 71,000 hours or more
Constant Brightness on
Brightness level
A
Time the projector can maintain constant brightness (approximate)
B
Brightness Level setting Time the projector can maintain constant brightness
(approximate)
50% 41,000 hours
40% 56,000 hours
30% or less 78,000 hours or more
Energy Saving Mode
s Settings > Brightness Settings > Energy Saving Mode
When set to On, you can reduce the power consumption by automatically
adjusting the light source brightness. The light source brightness is gradually
adjusted over a period of 60 minutes and it does not ruin the image
appearance.
When you use the Multi-Projection or Constant Brightness features, set to
Off to correct differences in the brightness between projectors.
This function is disabled in the following cases:
a
• When Edge Blending is set to Blending/Black Level or Black Level.
s Extended > Multi-Projection > Edge Blending
• When Color Mode is set to Multi-Projection.
s Image > Color Mode
• When Light Source Mode is set to Custom.
s Settings > Brightness Settings > Light Source Mode
Brightness Level setting Time the projector can maintain constant brightness
(approximate)
85% 6,000 hours
80% 10,000 hours
70% 19,000 hours
60% 29,000 hours
Remote Receiver
s Settings > Remote Receiver
When the remote control does not operate stably due to noise from other
devices, you can limit reception of remote control signals to the selected
receiver; Off turns off all receivers.
Page 88
Settings Menu
88
You can turn on all remote receivers by holding down the [Menu]
a
button on the remote control for approximately 15 seconds.
User Button
s Settings > User Button
You can assign the following menu options to the [User] buttons on the
remote control for one-touch access.
• Light Source Mode
• Multi-Projection
• Resolution
• On-Screen Display
• Display the QR Code
• Image Enhancement
• Frame Interpolation
• Link Menu
• Content Playback
• USB
The USB option is only displayed when Content Playback is set to On.
a
Test Pattern
s Settings > Test Pattern
• Press the [Page] button to change the test pattern while displaying a
a
test pattern.
• Press the [Esc] button to cancel pattern display.
• The test pattern's shape is determined by the Screen Type setting. Be
sure to set the correct screen type before adjusting with the test
pattern.
s Extended > Display > Screen > Screen Type
• To set menu items that cannot be set while the test pattern is being
displayed or to fine-tune the projected image, project an image from
the connected device.
• You can also display a test pattern using the [Test Pattern] button on
the control panel or remote control.
Memory
s Settings > Memory
You can save customized settings and then select the saved settings whenever
you want to use them.
Memory
You can save the following settings. You can register up to 10 memories
with different names.
• Image menu settings
• Scale in the Signal menu
• Light Source Mode and Brightness Level in the Settings menu
• Edge Blending, Color Matching, and Black Level in the Extended
menu
Lens Position
You can save the position of the lens adjusted using lens shift, zoom, focus,
and distortion. You can register up to 10 memories with different names.
You can display a test pattern to assist in focusing and zooming the image and
correcting image shape.
Geometry Correction
You can save the adjustment value of the geometry correction. You can
register up to 3 memories with different names.
You can use the following options for each memory type.
Page 89
Settings Menu
89
Load Memory
You can load the saved memory. The settings applied to the current image
are replaced with the settings in the memory.
Save Memory
You can save your current settings to memory.
Erase Memory
You can erase the selected memory settings.
Rename Memory
You can rename a saved memory.
Reset Memory Settings
You can delete all saved memories.
• A memory name that has already been used is indicated by a blue
a
mark. Saving over a previously saved memory overwrites the settings
with your current settings.
• The lens position when a memory is loaded may not completely
match the lens position when the memory was saved. If there is a
large discrepancy between the lens position, calibrate the lens.
• You can also open the Memory screen using the [Memory] button
on the remote control.
a
• You cannot select the Overlay Effect setting in the following cases.
• When Edge Blending is set to Blending/Black Level or Black
Level in the projector's Extended menu.
• When the current source is USB and there is no playlist being
played.
• When the current source is USB and a writing error has occurred.
• You can use the following methods to create playlists.
• Using Epson Projector Content Manager on your computer.
You can download and install Epson Projector Content Manager
from the following Web site.
epson.sn
• Using Epson Web Control with a Web browser.
• Using Epson Creative Projection on iOS devices.
You can download Epson Creative Projection from the App Store.
Any fees incurred when communicating with the App Store are the
responsibility of the customer.
• When you assign the USB function to the [User] button on the
remote control using the User Button setting in the projector's
Settings menu, you can start the playlist by pressing the [User]
button. When there is a timetable assigned, the playlist will play back
according to the schedule in the timetable.
• You can also hold down the [Num] and numeric buttons to project
your favorite playlist. You can set a remote control shortcut key
using the software you used to create the playlists.
Content Playback
s Settings > Content Playback
You can easily project your digital signage content: playlists that contain
images and movies saved on an external storage device.
Content Playback
Set to On to play back a playlist.
Overlay Effect
You can add color and shape effects to the projected image.
USB Viewer
You can select and play back a playlist saved on the USB flash drive.
gg Related Links
• "Creating Playlists Using Epson Web Control" p.89
• "Supported Content Playback Mode File Types" p.90
• "Content Playback Mode Restrictions" p.91
Creating Playlists Using Epson Web Control
In Content Playback mode, you can create playlists using a Web browser and
save them to a USB flash drive connected to a projector on a network.
Page 90
Settings Menu
90
Attention
Do not remove the USB flash drive from the projector or disconnect the projector's
power cord while creating playlists. Data saved on the USB flash drive may be
damaged.
Make sure the projector is operating in Content Playback mode.
a
Make sure your computer or device is connected to the same network
b
as the projector.
Make sure a USB flash drive is connected to the projector's USB-A port.
c
Start your Web browser on your computer or device.
d
Go to the Epson Web Control screen by entering the projector's IP
e
address into the browser's address box. When entering an IPv6 address,
wrap the address with [ and ].
Select USB Memory Device.
f
Select Upload New Data.
g
Edit the playlist.
j
When you have finished editing the playlist, select Finish.
k
• See the section in this guide covering Web Control Options for
a
gg Related Links
• "Epson Web Control" p.135
Supported Content Playback Mode File Types
You can project these types of files using the projector's Content Playback
feature.
details.
• You can play the playlist from the Remote or Playlist screen.
• When you want to specify when the playlist starts and finishes,
schedule the playlist using the Epson Projector Content Manager
software.
Select the images or movies you want to add to the playlist.
h
You can upload .avi, .jpeg (.jpg), .png, .bmp, or .gif files.
a
The selected files are copied to the connected USB flash drive.
Do one of the following:
i
• To add them to the existing playlist, select Add to Playlist and select
the playlist you want to add them to.
• To create a new playlist and add them to it, select Create New
Playlist.
If you want to add .mp4 or .mov files to the playlist, use the
Epson Projector Content Manager software or the Epson
Creative Projection app.
Page 91
Settings Menu
91
File contents File type
(extension)
Image .jpg
.bmp Make sure the file is not:
.gif
.png Make sure the file is not:
Movie .avi
(Motion
JPEG)
Details
• We recommend JPEGs taken with a digital still camera
that complies with the Exif standard.
• The number of vertical and horizontal pixels must be a
multiple of 8.
• Make sure the file is not:
• Progressive format
• Above 8192 × 8192 resolution
• Above 1280 × 800 resolution
• The image must be a transparent gif with a black
background.
• Make sure the file is not:
• Above 1280 × 800 resolution
• Animated
• Interlaced
• Above 1280 × 800 resolution
• Interlaced
• Version: AVI 1.0 only
• Resolution: 1280 × 800 or less
• Size: 2 GB or less
• Movie Codec: Motion JPEG
• Audio Codec: LPCM, IMA ADPCM, or no audio
• Audio Sampling Rate: 11.025 kHz, 22.05 kHz, 44.1
kHz, 16 kHz, 24 kHz, 32 kHz, or 48 kHz
• Changing the Color Temp. setting in the Image menu (when Warm White
or Cool White is selected as Color Filter)
• Split Screen
• Blanking
• Changing the Display Background setting in the Extended menu
• Changing the Screen setting in the Extended menu
• Changing the Log Save Destination setting in the Extended menu
• Using Edge Blending with Effects feature
• Detecting the input signal automatically
NFC Settings
s Settings > NFC Settings
You can prevent scanning to the projector's settings.
NFC Write Protection
Prevents anyone from scanning the projector's settings.
NFC Write Password
Set a password for scanning the projector's settings up to 32 alphanumeric
characters long.
If you do not set an NFC Write Password, NFC Write Protection is
a
enabled automatically when you turn on the projector. If you want to
scan the projector's information using the NFC tag on the projector, set
the NFC Write Password setting to Off.
Content Playback Mode Restrictions
Operating restrictions
The following operations cannot be performed in Content Playback mode.
Reset (Settings menu)
s Settings > Reset
You can reset all adjustment values on the Settings menu to their default
settings, except for the following:
• Audio Out Device
Page 92
Settings Menu
• Power On Link
• Power Off Link
• Link Buffer
• User Button
• NFC Settings
92
Page 93
Extended Menu
93
Settings on the Extended menu let you customize various projector setup
features.
gg Related Links
• "Home Screen" p.93
• "Menu Position" p.93
• "Message Position" p.94
• "Messages" p.94
• "Display Background" p.94
• "Startup Screen" p.94
• "Standby Confirmation" p.94
• "Screen" p.94
• "Panel Alignment" p.95
• "Color Uniformity" p.95
• "OSD Rotation" p.95
• "User's Logo" p.96
• "Projection" p.96
• "Direct Power On" p.96
• "Sleep Mode" p.96
• "Sleep Mode Timer" p.96
• "High Altitude Mode" p.96
• "Auto Source Search" p.97
• "Auto Power On" p.97
• "Startup Source" p.97
• "Quick Startup" p.97
• "USB Power" p.97
• "A/V Mute Settings" p.97
• "Shutter Settings" p.98
• "Remote Control Type" p.98
• "Beep" p.98
• "Indicators" p.98
• "Log Save Destination" p.99
• "Batch Setup Range" p.99
• "AC Voltage Monitoring" p.99
• "Lens Type" p.99
• "Date & Time" p.99
• "Lens Calibration" p.100
• "A/V Settings" p.100
• "Standby Mode" p.100
• "HDBaseT" p.100
• "Color Calibration" p.101
• "Projector ID" p.101
• "Projector Grouping" p.101
• "Tiling" p.101
• "Edge Blending" p.102
• "Black Level" p.102
• "Reset (Multi-Projection menu)" p.103
• "Screen Matching" p.103
• "Color Matching" p.104
• "Simple Stacking" p.104
• "Schedule Settings" p.105
• "Language" p.106
• "Reset (Extended menu)" p.106
Home Screen
s Extended > Home Screen
You can adjust settings on the Home screen.
Home Screen Auto Disp.
Set to On to display the Home screen automatically when there is no input
signal when turning on the projector.
Custom Function 1/Custom Function 2
Select menu options to be assigned to the Home screen.
Menu Position
s Extended > Display > Menu Position
You can select the position of the projector menu displayed on the screen.
Page 94
Extended Menu
94
Message Position
s Extended > Display > Message Position
You can select the position of messages displayed on the screen.
Messages
s Extended > Display > Messages
You can control whether messages are displayed on the screen.
Display Background
s Extended > Display > Display Background
You can select the screen color or logo to display when no signal is received.
Setting is only displayed when Content Playback is set to Off.
a
Standby Confirmation
s Extended > Display > Standby Confirmation
You can display a confirmation message after pressing the [Standby] button
on the remote control.
When set to Off, you can turn off the projector simply by pressing the
[Standby] button once.
Screen
s Extended > Display > Screen
You can set the aspect ratio and position of the projected image according to
the type of screen being used.
Screen Type
Set the aspect ratio of the screen to fit the image into the projection area.
Screen Position
You can shift the image position horizontally and vertically if there are
margins between the edge of the image and the projected screen frame due
to the Screen Type setting.
Startup Screen
s Extended > Display > Startup Screen
You can control whether a special screen appears when the projector starts
up.
This function is disabled when you turn on the projector in Quick
a
Startup mode.
a
• Adjust the aspect ratio for the projected image, if necessary.
• When the Screen Type setting changes, the EDID settings are
automatically adjusted.
• Settings are only displayed when Content Playback is set to Off.
• This setting is unavailable when projecting images from a computer
over a network.
• The Screen Type setting is not supported by the Message
Broadcasting feature in the Epson Projector Management software.
• You cannot adjust the screen position if you set the Screen Type
setting to the same aspect ratio as the projector resolution.
Page 95
Extended Menu
95
Panel Alignment
s Extended > Display > Panel Alignment
You can use the panel alignment feature to manually adjust the color
convergence (the alignment of the red and blue colors) in the projected image.
You can adjust the pixels horizontally and vertically in increments of 0.125
pixels within a range of ±3 pixels.
Panel Alignment
Set to On to correct color misalignment in the projected image.
Select Color
Select the color you want to adjust.
Pattern Color
Select the grid color displayed during adjustments.
• R/G/B to display the grid color in white.
• R/G to display the grid color in yellow.
• G/B to display the grid color in cyan.
The available color varies depending on the Select Color setting.
Start Adjustments
Starts the panel alignment process.
The image may become distorted while adjusting. The image is restored
once adjustments are complete.
• Shift the whole panel to adjust the whole panel roughly.
• Adjust the four corners to adjust the four corners of the panel precisely.
If you need to make additional adjustments, select Select intersection
and adjust to adjust more precisely.
Reset
You can reset all adjustment values on the Panel Alignment menu to their
default settings.
Color Uniformity
s Extended > Display > Color Uniformity
s Extended > Multi-Projection > Screen Matching > Color Uniformity
You can use the color uniformity feature to manually adjust the color tone
balance in the projected image.
Color Uniformity
Set to On to adjust the color tone balance for the whole screen.
Adjustment Level
Select the adjustment level you want to adjust.
There are eight adjustment levels, from white to gray to black. Adjust each
level individually.
Set to All to adjust the tint for each color from level 2 to 8 in a batch.
(Once the values of red, blue, or green are at maximum or minimum at
any level, you cannot perform further adjustments.)
Start Adjustments
Starts adjustments for the selected adjustment level.
The image may become distorted while adjusting. The image is restored
once adjustments are complete.
Adjust the outer areas first, and then adjust the entire screen.
Reset
You can reset all adjustment values on the Color Uniformity menu to
their default settings.
The color tone may not be uniform even after adjusting the color
a
uniformity.
a
• Image quality may decline after performing alignment.
• Images for pixels that extend beyond the edge of the projected screen
are not displayed.
OSD Rotation
s Extended > Display > OSD Rotation
You can rotate the menu display 90°.
Page 96
Extended Menu
96
User's Logo
s Extended > User's Logo
You can save an image on the projector and display it whenever the projector
turns on. You can also display the image when the projector is not receiving
an input signal. This image is called the user's logo screen.
You can select a photo, graphic, or company logo as the user's logo, which is
useful in identifying the projector's owner to help deter theft. You can prevent
changes to the user's logo by setting up password protection.
Display the image you want to project as the user's logo and then select this
setting.
• If the User's Logo Protection setting in the Password Protection
a
setting menu is set to On, set to Off before saving the user's logo.
• When you copy the menu settings from one projector to another
using the batch setup feature, user's logo is also copied. Do not
register the information that you do not want to share between
multiple projectors as a user's logo.
• You cannot save content that is protected by HDCP.
• When Content Playback is set to On, you can display the user's logo
only when the projector starts up.
• Adjustments for image shape and display range are temporarily
canceled when you select User's Logo.
Direct Power On
s Extended > Operation > Direct Power On
Set to On to turn on the projector by plugging it in without pressing the
power button.
Note that the projector also turns on automatically in cases such as recovery
from a power outage.
Sleep Mode
s Extended > Operation > Sleep Mode
Set to On to automatically turns off the projector after an interval of
inactivity.
Sleep Mode Timer
s Extended > Operation > Sleep Mode Timer
You can set the time before the projector automatically turns off from 1 to 30
minutes.
Projection
s Extended > Projection
You can set the way the projector faces the screen so the image is oriented
correctly.
You can change the projection mode to flip the image over top-to-
a
bottom by holding down the [A/V Mute] button on the remote control
for approximately 5 seconds.
This function is enabled only when Sleep Mode is set to On.
a
High Altitude Mode
s Extended > Operation > High Altitude Mode
When operating the projector at an altitude where the air is thin, the normal
rotation speed of the fans is not enough to cool the projector.
Set to On to increase the rotation speed of the fans at altitudes above 1500 m.
Page 97
Extended Menu
97
When set to On, the projector's operating temperature will rise.
a
Auto Source Search
s Extended > Operation > Auto Source Search
Set to On to detect the input signal automatically and project images when
there is no input signal.
• Setting is only displayed when Content Playback is set to Off.
a
Auto Power On
s Extended > Operation > Auto Power On
Computer
Select to automatically turn on the projector when it detects an input
signal from the image source.
• This function is disabled when you turn on the projector in the
Quick Startup mode.
You can select the image source you want to project when the projector is
turned on in Content Playback mode.
Quick Startup
s Extended > Operation > Quick Startup
You can set the time period for Quick Startup mode. The projector enters this
mode when you turn it off. You can start projecting in approximately 7
seconds by pressing the power button.
• Set A/V Output to While Projecting first.
a
• Available only when Auto Power On is set to Off or Computer.
USB Power
s Extended > Operation > USB Power
Set to Always On to continue supplying power to the streaming media player
when the projector is not projecting images. This lets the streaming media
player start earlier, or perform its firmware updates automatically over a
network if necessary.
HDMI
Select to automatically turn on the projector when it detects an HDMI
video signal.
This is useful for video meetings using Microsoft Teams Rooms. The
projector turns on automatically when it receives an HDMI video signal
from a device that supports Microsoft Teams Rooms and you can start the
meeting immediately.
Startup Source
s Extended > Operation > Startup Source
• Set A/V Output to While Projecting first.
a
• Available only when Auto Power On is set to Off or Computer.
A/V Mute Settings
s Extended > Operation > A/V Mute Settings
You can adjust the A/V Mute settings (EB‑PU2120W).
Page 98
Extended Menu
98
Fade-in
Set the number of seconds for a fade-in transition effect when displaying
an image.
Fade-out
Set the number of seconds for a fade-out transition effect when hiding an
image.
A/V Mute Timer
Turns off the projector automatically if A/V Mute is enabled and 2 hours
of inactivity has passed.
Release A/V Mute
Select A/V Mute if you want to use only the [A/V Mute] button to turn off
A/V mute or if you want to send a command to turn off A/V Mute, or
select Any Button to use any button to turn it off.
Shutter Settings
s Extended > Operation > Shutter Settings
You can adjust the shutter settings (EB‑PU2220B).
Fade-in
Set the number of seconds for a fade-in transition effect when displaying
an image.
Standby
Sets the shutter status when the projector is turned off. Select Last Used if
you want to maintain the current shutter status when the projector is
turned off.
Remote Control Type
s Extended > Operation > Advanced > Remote Control Type
If you want to adjust the zoom/focus/distortion of the projected image using
the Epson remote control as shown below, select Advanced as the Remote
Control Type setting.
Fade-out
Set the number of seconds for a fade-out transition effect when hiding an
image.
Shutter Timer
Turns off the projector automatically if the shutter is enabled and two
hours of inactivity have passed.
Shutter Release
Select Shutter to turn off the shutter function by using the [A/V Mute]
button only or by sending a command to turn off the shutter. Select Any
Button to use any button to turn off the shutter function.
Startup
Sets the shutter status when the projector is turned on.
Beep
s Extended > Operation > Advanced > Beep
You can control the beep that sounds when you turn the projector on or off.
Indicators
s Extended > Operation > Advanced > Indicators
Page 99
Extended Menu
99
Set to Off to turn off the indicator lights on the projector except when an
error or warning occurs.
Log Save Destination
s Extended > Operation > Advanced > Log Save Destination
You can set where you want to save the operation logs for the projector.
Select USB and Internal Memory to save logs as text files (.log) to a USB
flash drive inserted into the projector's USB-A port.
Setting is only displayed when Content Playback is set to Off.
a
Batch Setup Range
s Extended > Operation > Advanced > Batch Setup Range
You can select which menu settings you want copied.
All
Select this to copy all of the projector menu settings using the batch setup
feature.
Limited
Select this if you do not want to copy the Password Protection, EDID,
and Network menu settings.
If you regularly turn off the projector by turning off the power outlet (direct
shutdown), set to Off.
You can view the log in the projector's Info menu.
a
s Info > Voltage Warning Info
Lens Type
s Extended > Operation > Advanced > Lens Type
Select the model number for the attached lens when using the following
lenses:
• ELPLS04
• ELPLU02
• ELPLR04
• ELPLW04
• ELPLM06
• ELPLM07
• ELPLL07
Date & Time
s Extended > Operation > Date & Time
You can adjust the projector's system time and date settings.
AC Voltage Monitoring
s Extended > Operation > Advanced > AC Voltage Monitoring
Set to On to monitor the projector's voltage status and obtain a log when a
warning, disconnection, or power blockage occurs.
Daylight Saving Time
Adjust the daylight saving time settings for your region.
Internet Time
Turn on this setting to update the date and time automatically through an
Internet time server.
Page 100
Extended Menu
100
When you set Schedule Protection to On in the Password Protection
a
screen, you cannot change the time and date settings. Set Schedule
Protection to Off first.
Lens Calibration
s Extended > Operation > Lens Calibration
You can view information about the lens currently in use.
It takes up to approximately 100 seconds. When calibration is finished, the
lens returns to the same position it was in before calibration.
The following lenses return to the standard position.
• ELPLX02S
• ELPLX02WS
A/V Settings
s Extended > A/V Settings
You can select to output audio and video to an external device when the
projector is in standby mode (when the power is off).
Select Always On to output audio and images to external devices when the
projector does not project any images.
• Available only when Quick Startup is set to Off, and Auto Power
a
On is set to Off or Computer.
• When set to Always On, you can move the lens position to the home
position even if the projector is in standby mode.
• When set to Always On, and Control Communication is set to On,
communication from the HDBaseT port is enabled even if the
projector is in standby mode.
Standby Mode
s Extended > Standby Mode
Set to Communication On to monitor and control the projector over a
network.
• Set A/V Output to While Projecting first.
a
• Available only when Auto Power On is set to Off or Computer.
• Available only when USB Power is set to On While Projecting.
HDBaseT
s Extended > HDBaseT
You can select the communication settings for connections to an HDBaseT
transmitter or switcher.
Control Communications
You can enable or disable communication from the Ethernet and serial
ports on the HDBaseT transmitter or switcher; set to On to disable the
projector's LAN, RS-232C, and Remote ports.
Extron XTP
Set to On when you connect an Extron XTP transmitter or switcher to the
HDBaseT ports. See the following Extron Web site for more details on the
XTP system.
http://www.extron.com/
• Control Communications is only displayed when Extron XTP is set
a
to Off.
• When Extron XTP is set to On, the cooling fans may run even in
standby status. This is not a malfunction.
Loading...