Epson EB-93H, EB-93e, EB-93 User Manual

User’s Guide

Notations Used in This Guide

• Safety indications

The documentation and the projector use graphical symbols to show how to use the projector safely. Please understand and respect these caution symbols in order to avoid injury to persons or property.

Warning

Caution

• General information indications

Attention

s Indicates a page where detailed information regarding a topic can be found.

[Name] Indicates the name of the buttons on the remote control or the control panel.

Menu Name Indicates Configuration menu items.

This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

Indicates procedures which may result in damage or injury if sufficient care is not taken.

Indicates additional information and points which may be useful to know regarding a topic.

Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendix".

s "Glossary" p.119

Example: [Esc] button

Example: Select Brightness from Image. Image - Brightness

Notations Used in This Guide ........................ 2

Introduction

Projector Features .......................................... 7

List of Functions by Model........................................7

Quick and Easy Set up, Projection, and Storage ..........................7

Easy writing on a whiteboard or blackboard using the pattern function ........7

Connecting with a USB cable and projecting (USB Display)................ 7

Detecting projector movements and automatically correcting image distortion

.........................................................8

Useful Functions for Projecting Images ................................ 8

Connecting to a network and projecting images from the computer's screen

(EB-93 only)................................................8

Easy connection to a computer with Quick Wireless (EB-93 only)............8

Making the most of the remote control.............................8

Enlarge and project your files with the Document Camera.................8

Enhanced security functions..................................... 8

Part Names and Functions .................................. 10

Front/Top ...................................................10

Rear.......................................................11

Base ...................................................... 12

Control Panel................................................13

Remote Control...............................................14

Replacing the remote control batteries............................. 16

Remote control operating range.................................17

Preparing the Projector

Installing the Projector ..................................... 19

Installation Methods ........................................... 19

Installation methods .........................................19

Screen Size and Approximate Projection Distance.......................20

Connecting a Computer ......................................... 21

Connecting Image Sources.......................................22

Connecting USB Devices.........................................24

Connecting External Equipment...................................25

Connecting a LAN Cable (EB-93 only)................................ 26

Basic Usage

Projecting Images ......................................... 28

From Installation to Projection.....................................28

Automatically Detect Input Signals and Change the Projected Image (Source Search)

.......................................................... 29

Switching to the Target Image by Remote Control ....................... 30

Projecting with USB Display......................................30

System requirements......................................... 30

Connecting for the first time ....................................31

Uninstalling...............................................32

Adjusting Projected Images ................................ 34

Correcting Keystone Distortion .................................... 34

Correcting automatically (Auto V-Keystone) .........................34

Correcting manually (manual H/V-Keystone) .........................34

Correcting manually (Quick Corner)............................... 35

Adjusting the Image Size ........................................ 37

Adjusting the Image Position ..................................... 37

Adjusting the Horizontal Tilt......................................37

Correcting the Focus...........................................38

Adjusting the Volume..........................................38

Selecting the Projection Quality (Selecting Color Mode) ...................38

Setting Auto Iris ..............................................39

Changing the Aspect Ratio of the Projected Image ......................40

Changing methods ..........................................40

Changing the aspect mode .....................................40

Connecting Equipment ..................................... 21

Contents

Useful Functions

Projection Functions ....................................... 43

Projecting Without a Computer (Slideshow) ...........................43

Specifications for files that can be projected using Slideshow..............43

Slideshow examples .........................................43

Slideshow operating methods...................................43

Projecting the selected image...................................45

Projecting image files in a folder in sequence (Slideshow) ................ 46

Image file display settings and Slideshow operation settings..............47

Hiding the Image and Sound Temporarily (A/V Mute).....................48

Freezing the Image (Freeze) ......................................48

Pointer Function (Pointer) ........................................49

Enlarging Part of the Image (E-Zoom) ................................ 50

Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse) . . . . . . 51

Saving a User's Logo ........................................... 52

Saving User Pattern ............................................54

Security Functions ......................................... 56

Managing Users (Password Protect)................................. 56

Kinds of Password Protect ......................................56

Setting Password Protect......................................56

Entering the Password ........................................57

Restricting Operation (Control Panel Lock)............................ 58

Anti-Theft Lock ............................................... 59

Installing the wire lock ........................................59

Monitoring and Controlling ................................ 60

About EasyMP Monitor (EB-93 Only) .................................60

Changing Settings Using a Web Browser (Web Control) (EB-93 Only)...........60

Projector setup ............................................. 60

Displaying the Web Control screen ...............................61

Displaying the Web Remote screen............................... 61

Using the Mail Notification Function to Report Problems (EB-93 Only)..........63

Reading Error Notification Mail ..................................63

Management Using SNMP (EB-93 Only)..............................63

ESC/VP21 Commands ........................................... 64

Command list.............................................. 64

Cable layouts.............................................. 64

About PJLink (EB-93 Only) ........................................65

About Crestron RoomView

Operating a projector from your computer..........................66

(EB-93 Only) ............................. 66

Configuration Menu

Using the Configuration Menu .............................. 71

List of Functions ........................................... 72

Configuration Menu Table.......................................72

Network menu (EB-93 only) ..................................... 73

Image Menu ................................................. 73

Signal Menu ................................................. 74

Settings Menu ................................................76

Extended Menu ...............................................78

Network Menu (EB-93 only).......................................79

Notes on operating the Network menu.............................80

Soft keyboard operations......................................80

Basic menu ................................................81

Wired LAN menu ............................................ 82

Mail menu................................................ 82

Others menu..............................................83

Reset menu ............................................... 84

Info Menu (Display Only) ........................................84

Reset Menu .................................................85

Troubleshooting

Using the Help ............................................. 87

Problem Solving ........................................... 88

Reading the Indicators.......................................... 88

When the Indicators Provide No Help ................................91

Problems Relating to Images ...................................... 92

No images appear...........................................92

Contents

Moving images are not displayed (only the moving image portion turns black)

........................................................ 93

Projection stops automatically ...................................93

"Not supported" is displayed.................................... 93

"No Signal" is displayed .......................................93

Images are fuzzy, out of focus, or distorted.......................... 94

Interference or distortion appear in images ..........................95

The image is truncated (large) or small, or the aspect is not suitable.........95

Image colors are not right...................................... 96

Images appear dark.......................................... 97

Problems when Projection Starts...................................97

The projector does not turn on..................................97

Other Problems...............................................98

No sound can be heard or the sound is faint .........................98

The remote control does not work................................98

I want to change the language for messages and menus................. 99

Mail is not received even if an error occurs with the projector.............99

About Event ID (EB-93 Only) ............................... 100

Maintenance

Cleaning ................................................. 102

Cleaning the Projector's Surface ................................... 102

Cleaning the Lens ............................................ 102

Cleaning the Air Filter ..........................................102

Appendix

Optional Accessories and Consumables .................... 110

Optional Accessories .......................................... 110

Consumables............................................... 110

Screen Size and Projection Distance ........................ 111

Projection Distance........................................... 111

Supported Monitor Displays ............................... 112

Supported Resolutions ......................................... 112

Computer signals (analog RGB)................................. 112

Component Video .......................................... 112

Composite video ........................................... 112

Input signal from the HDMI port ................................ 112

Specifications ............................................ 114

Projector General Specifications...................................114

Appearance .............................................. 118

Glossary ................................................. 119

General Notes ............................................ 121

About Notations ............................................. 121

General Notice: .............................................. 121

Index .................................................... 139

Replacing Consumables ................................... 104

Replacing the Lamp........................................... 104

Lamp replacement period .....................................104

How to replace the lamp ......................................105

Resetting the lamp hours ..................................... 107

Replacing the Air Filter ......................................... 107

Air filter replacement period ................................... 107

How to replace the air filter .................................... 107

Introduction

This chapter explains the projector's features and the part names.

Projector Features

List of Functions by Model

Available functions differ depending on the model being used. See the table below for a list of the functions available for each model.

Function EB-93 EB-92

USB Display

HDMI Connection

Auto V-Keystone

Quick Wireless Connection

Wired LAN Connection

Network Settings

Slideshow

The USB display requires a commercially available USB cable.

*1 *2 The HDMI connection requires a commercially available HDMI cable. *3 The Quick Wireless Connection requires a Quick Wireless Connection USB

Key.

Quick and Easy Set up, Projection, and Storage

• Turn the projector on and off by simply plugging in or unplugging.

• Project onto large screens from a short distance.

• Make easy height adjustments with one lever.

• No cool down delay makes it easy to put away.

Easy writing on a whiteboard or blackboard using the pattern function

You can project ruled lines and grid patterns. This is useful when drawing diagrams on a whiteboard or blackboard.

s Settings - Pattern p.76

Connecting with a USB cable and projecting (USB Display)

By simply connecting a commercially available USB cable, you can project images from a computer's screen without a computer cable.

s "Projecting with USB Display" p.30

Projector Features

Detecting projector movements and automatically correcting image distortion

This projector automatically corrects keystone distortion which occurs when positioning or moving the projector.

"Correcting automatically (Auto V-Keystone)" p.34

Useful Functions for Projecting Images

Connecting to a network and projecting images from the computer's screen (EB-93 only)

You can connect the projector to a computer on a network and project the computer's screen using the supplied EasyMP Network Projection (application software).

sEasyMP Network Projection Operation

Guide

Easy connection to a computer with Quick Wireless (EB-93 only)

By simply connecting the optional Quick Wireless Connection USB Key to a computer, you can project the computer's screen. (Windows computers only)

Making the most of the remote control

You can use the remote control to perform operations such as enlarging part of the image. You can also use the remote control as a pointer during presentations or as a mouse for the computer.

"Pointer Function (Pointer)" p.49

"Enlarging Part of the Image (E-Zoom)" p.50

"Using the Remote Control to Operate the Mouse Pointer (Wireless

Mouse)" p.51

Enlarge and project your files with the Document Camera

You can project paper documents and objects using the optional Document Camera. Image focus is automatically adjusted using the auto focus function. You can also enlarge images using digital zoom.

"Optional Accessories" p.110

Enhanced security functions

• Password Protect to restrict and manage users

By setting a Password you can restrict who can use the projector.

"Managing Users (Password Protect)" p.56

• Control Panel Lock restricts button operation on the control panel

You can use this to prevent people changing projector settings without permission at events, in schools, and so on.

"Restricting Operation (Control Panel Lock)" p.58

Projector Features

• Equipped with various anti-theft devices

The projector is equipped with the following types of anti-theft security devices.

• Security slot

• Security cable installation point

"Anti-Theft Lock" p.59

Part Names and Functions

All of the features in this guide are explained using illustrations of EB-93 unless otherwise mentioned.

Front/Top

Name Function

Foot adjust lever

Front adjustable foot

A/V mute slide

Focus ring

Air intake vent

(air filter)

Air filter cover open/

close switch

Zoom ring

Control panel

Press the foot lever to extend and retract the front foot. s "Adjusting the Image Position" p.37

When setup on a surface such as a desk, extend the foot to adjust the position of the image.

s "Adjusting the Image Position" p.37

Close when not using the projector to protect the lens. By closing during projection you can hide the image and the sound.

s "Hiding the Image and Sound Temporarily (A/V Mute)" p.48

Adjusts the image focus. s "Correcting the Focus" p.38

Takes in air to cool the projector internally. s "Cleaning the Air Filter" p.102

Opens and closes the air filter cover. s "Replacing the Air Filter" p.107

Adjusts the image size. s "Adjusting the Image Size" p.37

Operates the projector. s "Control Panel" p.13

Name Function

Air exhaust vent

Remote receiver

A/V mute slide knob

Exhaust vent for air used to cool the projector internally.

Caution

While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent.

Receives signals from the remote control.

Slide the knob to open and close the A/V mute slide.

Lamp cover

Indicators

Open when replacing the projector's lamp. s "Replacing the Lamp" p.104

Indicates the projector's status. s "Reading the Indicators" p.88

Part Names and Functions

Rear

HDMI port

Power inlet

S-Video port

Video port

Audio-L/R port

Audio1 port

Monitor Out port

Name Function

Inputs video signals from HDMI compatible video equipment and computers. This projector is compatible with

HDCPg.

s "Connecting Equipment" p.21

Connects the power cable to the projector. s "From Installation to Projection" p.28

For S-video signals from video sources.

Inputs composite video signals from video sources.

Inputs audio from equipment connected to the S-Video port or the Video port.

Inputs audio from equipment connected to the Computer1 port.

Outputs analog RGB signals input from the Computer1 port to an external monitor. You cannot output signals input from other ports or component video signals.

Name Function

RS-232C port

Security slot

Speaker

Remote receiver

LAN port

(EB-93 only)

USB(TypeA) port

USB(TypeB) port

Computer2 port

Computer1 port

When controlling the projector from a computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used.

s "ESC/VP21 Commands" p.64

The security slot is compatible with the Microsaver Security System manufactured by Kensington.

s "Anti-Theft Lock" p.59

Plays back audio.

Receives signals from the remote control.

Connects a LAN cable to connect to a network.

• Connects a USB memory device or a digital camera, and projects images as a Slideshow. s "Projecting Without a Computer (Slideshow)"

p.43

• Connects the optional Document Camera.

• Connects the projector to a computer via a

commercially available USB cable, and projects the images on the computer. s "Projecting with USB Display" p.30

• Connects the projector to a computer via the commercially available USB cable to use the Wireless Mouse function. s "Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)" p.51

Inputs image signals from a computer and component video signals from other video sources.

Audio Out port

Audio2 port

Outputs audio from the currently projected image to an external speaker.

Inputs audio from equipment connected to the Computer2 port.

Part Names and Functions

Base

Name Function

Front adjustable foot

Security cable

installation point

When setup on a surface such as a desk, extend the foot to adjust the position of the image.

s "Adjusting the Image Position" p.37

Pass a commercially available wire lock through here and lock it in place.

s "Anti-Theft Lock" p.59

Name Function

Ceiling mount fixing

points (three points)

Rear feet

Attach the optional Ceiling Mount here when suspending the projector from a ceiling.

s "Installing the Projector" p.19 s "Optional Accessories" p.110

When setup on a surface such as a desk, turn to extend and retract to adjust the horizontal tilt.

s "Adjusting the Horizontal Tilt" p.37

Part Names and Functions

Control Panel

Name Function

[t] button

[Source Search]

button

[Enter] button

Turns the projector power on or off. s "From Installation to Projection" p.28

Changes to the next input source that is sending an image. s "Automatically Detect Input Signals and Change the

Projected Image (Source Search)" p.29

• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.

• If pressed while projecting analog RGB signals from the Computer1 port or Computer2 port, you can automatically optimize Tracking, Sync., and Display Position.

[w][v] buttons

[a][b] button

[Help] button

[Esc] button

[<][>] buttons

[Menu] button

Name Function

• Performs vertical keystone correction.

s "Correcting keystone distortion in vertical directions" p.34

• If pressed when the Configuration menu or the Help screen is displayed, these buttons select menu items and setting values.

s "Using the Configuration Menu" p.71 s "Using the Help" p.87

[a] Decreases the volume. [b] Increases the volume.

"Adjusting the Volume" p.38

Displays and closes the Help screen which shows you how to deal with problems if they occur.

s "Using the Help" p.87

• Stops the current function.

• If pressed when the Configuration menu is displayed, it

moves to the previous menu level. s "Using the Configuration Menu" p.71

• Performs horizontal keystone correction. s "Correcting keystone distortion in horizontal directions" p.35

• If pressed when the Configuration menu or the Help screen is displayed, these buttons select menu items and setting values.

s "Using the Configuration Menu" p.71 s "Using the Help" p.87

Displays and closes the Configuration menu. s "Using the Configuration Menu" p.71

Part Names and Functions

Remote Control

Name Function

[t] button

[Computer] button

[Video] button

Numeric buttons

[A/V Mute] button

[Freeze] button

[Auto] button

Turns the projector power on or off. s "From Installation to Projection" p.28

Each time you press the button, the input changes between images from the Computer1 port and the Computer2 port.

Each time the button is pressed, the image cycles through the S-Video, Video, and HDMI ports.

• Enter the Password. s "Setting Password Protect" p.56

• Use this button to enter numbers in Network settings from the Configuration menu.

Turns the video and audio on or off. s "Hiding the Image and Sound Temporarily (A/V

Mute)" p.48

Images are paused or unpaused. s "Freezing the Image (Freeze)" p.48

If pressed while projecting analog RGB signals from Computer1 port or Computer2 port, you can automatically optimize Tracking, Sync., and Display Position.

[Aspect] button

[Page] buttons

[Up] [Down]

Each time the button is pressed, the aspect mode changes. s "Changing the Aspect Ratio of the Projected Image "

p.40

Changes pages in files such as PowerPoint files when using the following projection methods.

• When using the Wireless Mouse function s "Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)" p.51

• When using USB Display s "Projecting with USB Display" p.30

• When connecting to a network (EB-93 only)

When projecting images using Slideshow, pressing these buttons displays the previous/next screen.

Part Names and Functions

Name Function

[E-Zoom] buttons

[z][x]

[Menu] button

[ ][ ]

[

][ ] buttons

[Enter] button

[Esc] button

Enlarges or reduces the image without changing the projection size.

s "Enlarging Part of the Image (E-Zoom)" p.50

Displays and closes the Configuration menu. s "Using the Configuration Menu" p.71

• When the Configuration menu or the Help screen is displayed, pressing these buttons selects menu items and setting values. s "Using the Configuration Menu" p.71

• When projecting a Slideshow, pressing these buttons displays the previous/next image, rotates the image, and so on. s "Slideshow operating methods" p.43

• During Wireless Mouse function, the mouse pointer moves in the direction of the button that was pushed. s "Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)" p.51

• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level. s "Using the Configuration Menu" p.71

• Acts as a mouse's left button when using the Wireless Mouse function. s "Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)" p.51

• Stops the current function.

• If pressed when the Configuration menu is displayed, it

moves to the previous level. s "Using the Configuration Menu" p.71

• Acts as a mouse's right button when using the Wireless Mouse function. s "Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)" p.51

Name Function

[Volume] buttons

[a][b]

[Pointer] button

[Help] button

[Color Mode] button

[Num] button

[User] button

[USB] button

[LAN] button

[Source Search]

button

[a] Decreases the volume. [b] Increases the volume. s "Adjusting the Volume" p.38

Displays the on-screen pointer. s "Pointer Function (Pointer)" p.49

Displays and closes the Help screen which shows you how to deal with problems if they occur.

s "Using the Help" p.87

Each time the button is pressed, the Color Mode changes. s "Selecting the Projection Quality (Selecting Color

Mode)" p.38

Hold down this button and press the numeric buttons to enter passwords and numbers.

s "Setting Password Protect" p.56

Select any frequently used item from the six available Configuration menu items, and assign it to this button. By pressing the [User] button, the assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/adjustments.

s "Settings Menu" p.76 Power Consumption is assigned as the default setting.

Each time the button is pressed, it cycles through the following images:

• USB Display

• Images from the device connected to the USB(TypeA)

port

Changes to the image projected with EasyMP Network Projection. When projecting using the optional Quick Wireless Connection USB Key, this button switches to that image. (EB-93 only)

Changes to the next input source that is sending an image. s "Automatically Detect Input Signals and Change the

Projected Image (Source Search)" p.29

Part Names and Functions

Name Function

Remote control light-

emitting area

Outputs remote control signals.

Replacing the remote control batteries

If delays in the responsiveness of the remote control occur or if it does not operate after it has been used for some time, it probably means that the batteries are becoming flat. When this happens, replace them with new batteries. Have two AA size manganese or alkaline batteries ready. You cannot use other batteries except for the AA size manganese or alkaline.

Attention

Make sure you read the following manual before handling the batteries. s Safety Instructions

Remove the battery cover.

While pushing the battery compartment cover catch, lift the cover up.

Replace the old batteries with new batteries.

Part Names and Functions

Caution

Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.

Remote control operating range

Replace the battery cover.

Press the battery compartment cover until it clicks into place.

Preparing the Projector

This chapter explains how to install the projector and connect projection sources.

Installing the Projector

Installation Methods

The projector supports the following four different projection methods. Install the projector according to the conditions of the installation location.

• Project images from in front of the screen. (Front projection)

• Suspend the projector from the ceiling and project images from in front of a screen. (Front/Ceil‐ ing projection)

• Project images from behind a translucent screen. (Rear projec‐ tion)

• Suspend the projector from the ceiling and project images from behind a translucent screen. (Rear/Ceiling projection)

Warning

• A special method of installation is required when suspending the projector from a ceiling (ceiling mount). If it is not installed correctly, it could fall causing an accident and injury.

• If you use adhesives on the Ceiling mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its ceiling mount. This could cause serious injury to anyone under the ceiling mount and could damage the projector. When installing or adjusting the ceiling mount, do not use adhesives to prevent the screws from loosening and do not use oils or lubricants and so on.

Attention

• Do not use the projector on its side. This may cause malfunctions to occur.

• Do not cover the projector's air intake vent or air exhaust vent. If either of

the vents are covered, the internal temperature could rise and cause a fire.

• An optional Ceiling mount is required when suspending the

projector from a ceiling. s "Optional Accessories" p.110

• You can change the setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.

FrontWFront/Ceiling Set Rear or Rear/Ceiling from the Configuration menu. s Extended - Projection p.78

Installation methods

Install the projector as follows.

Installing the Projector

• Install the projector so that it is parallel to the screen. If the projector is installed at an angle to the screen, keystone distortion occurs in the projected image.

• Place the projector on a level surface. If the projector is tilted the projected image is also tilted.

• See the following if you cannot install the projector parallel to the

screen. s "Correcting Keystone Distortion" p.34

• See the following if you cannot install the projector on a level surface.

s "Adjusting the Horizontal Tilt" p.37

When you correct keystone distortion, the projected image may be

4:3 Screen Size

reduced.

Screen Size and Approximate Projection Distance

Projection size is determined by the distance from the projector to the screen. See the illustrations on the right to select the best position according to the screen size. The illustrations show the approximate shortest distance at maximum zoom. See the following for more information on the projection distance.

"Screen Size and Projection Distance" p.111

Connecting Equipment

Illustrations in this section are of EB-93.

The port name, location, and connector orientation differ depending on the source being connected.

Connecting a Computer

To project images from a computer, connect the computer using one of the following methods.

When using the supplied computer cable

Connect the computer's display output port to the projector's Computer1 or Computer2 port.

When using a commercially available USB cable

Connect the computer's USB port to the projector's USB(TypeB) port.

When using a commercially available HDMI cable

Connect the computer's HDMI port to the projector's HDMI port.

Computer1/2

Audio1/2

USBTypeB

HDMI

• You can use a commercially available USB cable to connect the projector to a computer to project images from the computer. This function is called USB Display.

s "Projecting with USB Display" p.30

• You can output audio from the projector's speaker by connecting the computer's audio output port to the projector's Audio1 or Audio2 port using a commercially available audio cable.

Connecting Equipment

Connecting Image Sources

To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.

When using a commercially available video or S-video cable

Connect the video or S-video output port on the image source to the projector's Video or S-Video port.

When using the optional component video cable

s "Optional Accessories" p.110

Connect the component output port on the image source to the projector's Computer1 or Computer2 port.

When using a commercially available HDMI cable

Connect the HDMI port on the image source to the projector's HDMI port using a commercially available HDMI cable.

Video

S-Video

S-VIDEO

Audio(L-R)

Computer1/2

Audio1/2

HDMI

Connecting Equipment

Attention

• If the input source is on when you connect it to the projector, it could cause a malfunction.

• If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.

• If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.

• When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".

• You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a

commercially available audio cable.

Connecting Equipment

Connecting USB Devices

You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.

Using the USB cable supplied with the USB device, connect the USB device to the USB(TypeA) port on the projector.

When the USB device is connected, you can project image files on the USB memory or digital camera using Slideshow.

"Slideshow examples" p.43

If the Document Camera is connected while projecting images from another input port, press the [USB] button on the remote control, or the [Source Search] button on the control panel, to switch to images from the Document Camera.

"Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.29

Attention

• If you use a USB hub, the connection may not operate correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.

• When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.

• Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.

• Use a USB cable less than 3 m in length. If the cable exceeds 3 m, Slideshow may not function correctly.

Connecting Equipment

Removing USB devices

After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from the projector.

Connecting External Equipment

You can output images and audio by connecting an external monitor or speaker. You can also output microphone audio from the projector's speaker by connecting a microphone.

When outputting images to an external monitor

Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.

When outputting audio to an external speaker

Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.

MonitorOut

AudioOut

Connecting Equipment

• If you set Standby Mode to Communication On, you can output images to an external monitor even if the projector is in standby mode.

s Extended - Standby Mode p.78

• Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video signals.

• Setting gauges for functions such as Keystone, Configuration Menu, or Help screens are not output to the external monitor.

• When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external

output.

Connecting a LAN Cable (EB-93 only)

Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN cable.

To prevent malfunctions, use a category 5 shielded LAN cable.

Basic Usage

This chapter explains how to project and adjust images.

Projecting Images

From Installation to Projection

This section explains the procedure for connecting the projector to a computer with the computer cable and projecting images.

Turn on your computer.

If the image is not projected, you can change the projected image using one of the following methods.

• Press the [Source Search] button on the control panel or the remote

• Press the button for the target port on the remote control.

Change the computer's screen output.

When using a laptop computer, you need to change the screen output from the computer.

Hold down the Fn key (function key), and press the b key.

The method for changing differs depending on the computer

control.

"Automatically Detect Input Signals and Change the Projected Image

(Source Search)" p.29

"Switching to the Target Image by Remote Control" p.30

being used. See the documentation supplied with the computer.

After projecting the image, adjust the image if necessary.

s "Correcting Keystone Distortion" p.34 s "Correcting the Focus" p.38

a b c d

Connect the projector to an electrical outlet with the power cable.

Connect the projector to the computer with the computer cable.

Turn on the projector.

Slide open the A/V mute slide.

Projecting Images

Automatically Detect Input Signals and Change the Projected Image (Source Search)

Press the [Source Search] button to project images from the port currently receiving an image.

Because only images from ports receiving an image are projected, you can quickly project the image you want.

Using the remote control Using the control panel

The following screen is displayed while no image signals are input.

Example: EB-93

* EB-93 only.

When two or more image sources are connected, press the [Source Search] button until the target image is projected.

When your video equipment is connected, start playback before beginning this operation.

Projecting Images

Switching to the Target Image by Remote Control

You can change directly to the target image by pressing the following buttons on the remote control.

Remote control

Each time the button is pressed, it cycles through the following images:

• Computer1 port

• Computer2 port

Each time the button is pressed, it cycles through the following images:

• S-Video port

• Video port

• HDMI port

Each time the button is pressed, it cycles through the following images:

• USB Display

• Images from the device connected to the USB(TypeA) port

Changes to the image projected with EasyMP Network Projection. When

projecting using the optional Quick Wireless Connection USB Key, this button switches to that image. (EB-93 only)

Projecting with USB Display

You can use the commercially available USB cable to connect the projector to a computer to project images from the computer.

To start USB Display, set USB Type B to USB Display from the Configuration menu.

Extended - USB Type B p.78

System requirements

For Windows

CPU

Amount of Memory

Hard Disk Space

Display

Windows 2000 Service Pack 4 The following 32 bit operating systems: Windows XP Windows XP Service Pack 2 or later Windows Vista Windows Vista Service Pack 1 or later Windows 7 The following 64 bit operating systems: Windows 7

Mobile Pentium III 1.2 GHz or faster Recommended: Pentium M 1.6 GHz or faster

256 MB or more Recommended: 512 MB or more

20 MB or more

Resolution of no less than 640x480 and no higher than 1600x1200.

Display color in 16-bit color or greater

+ 111 hidden pages