Continuous Ink Supply System
for
Epson Stylus C58
Installation Instruction
For ST Prefilled Version
This Version of the Continuous Ink Flow System comes with Prefilled
Cartridges and Auto Reset Chips. You just need to fill the Reservoir
bottles and print! The whole operation is very easy. It’s really an effective
tool to save your money.
1、General Guide:
1) Components
A、CIS system 1 set B、 Air filters 4pcs C、Support Arm 1 set
D、Refill Kit 4 pcs E、Instruction CD 1pc
2) Opening box inspection
a、Check whether all the accessories are ready.
b、Check whether there's the leakage of the CISS, whether some tubes have been
separated from the CISS, whether there are air bubbles in the tube (If there exists more
than 20CM air space, please kindly to contact with the local dealer)
2、Printer testing:
1) Check whether the printer is in normal condition, like mechanical status, lubrication status etc.
2) Print testing lines to ensure the printing head is good condition.
3) Print pictures to see whether the printing image is ok.
3、Installation Procedures:
1) First step
Put the CISS on the left side Pull out the small rubber plug Place air filters into air holes,
of the printer. In the meantime from the air hole as above the thicker side，is down into tank.
place all the tubes at correct position picture shown.
2) Set up the Continuous Ink Supply System
Move the cartridge car Uplug the power connector
Press the “ink cartridge replace
Button” to cartridge remove position
Open the cartridge cover to use a small screwdriver to loosen Circumgyrate the screwdriver clockwise
certain angle the cartridge cover, then remove the cartridge cover.
Remove the original cartridges Insert our no-sponge cartridge into printer carefully
3) Fix supporting arm
Tear off the sticker, and place one on the inner side of printer, and place another small tube clip on the right
side of printer, as above picture shown.
4)Install the tubing.
Put the tube into the Support Arm and Small Tube clamp as the below picture shown.
Move the cartridges to the left side. Place the tube through the two small tube clips, as above picture shown.
5) Adjust Tubing
Slide the cartridge car from left to right several times; make sure the tubes not too tight when cartridge is
in the far left position, and not too loose which to avoid tubing block. Pls refer to the below pictures.
Too long Distorted Well-installed
Plug the power connector Turn on the power
Watch for anything unusual.
6) Checking the printing head
Normal
Nozzle check is normal, start printing
Abnormal
Pls clean printing head
进入打印机喷嘴检查选项
Enter in the Printer Services panel and print a Demo Page.
If there shows any breaks (maybe it caused by air bubbles in the printing head), please
clean your printing head. If it is still shown little breaks, especially only for one color, it is
unnecessary to repeatedly clean printer-head. Just keep the printer unuse for about one
hour and print a Demo Page again. If it is still abnormal, please kindly contact local dealer.
4、Auto Reset Procedure
Ink indicator light sparkling, Till the Demo Page appear “X”,
but it still can work. which indicates to replace the cartridges
There are two Cartridge reset method:
1. Click “How to”, and follow up the info, till “OK” finished.
2. Push the button with red light directly on the left side of printer for
one time, when cartridges move, press that button again. Then
you will see the cartridge with full ink again.
5. Add ink into the reservoir bottles.
Please pay attention to the ink level in the reservoirs; if the ink level is below 1CM as the
above picture shown, please use refill kits to fill ink into Reservoir bottles. Carefully pull out
the rubber plugs from the refill holes.(there is possibility of ink spattering. Be careful!) Refill
ink according to the color in short supply. Then put the rubber back. (Please keep the printer
and the reservoir at the same horizontal line during the process of refilling ink.)
6. Close the cartridge cover as the below pictures shown.
7、Attention for maintenance:
Take out the CISS including the inner cartridges and other components. Then
remove support arm from printer, and place the original cartridges in. Please
inquire local dealer before sending to maintenance.
Notice:
1. Please don’t take out cartridge at random after installing the CIS system.
Keep the reservoir bottles on the same level with the printer.
2. Try to keep at least 1/2 inch of ink in the bottles, as you don’t want to run out
of ink and draw air into the cartridge.
3. Don’t place the Reservoir Bottles higher or lower much than the printer.
4. To be used in a dry place between 15 and 35 degree. Avoid exposure to direct
sunlight.
5. Don’t put the continuous ink supply systems reversed or leaning during the
shipment. Please make sure all the ink filling holes and Ventilation holes are
closed tightly during the transportation. Otherwise, the ink shall leak out.
6. Don’t sway the cartridge frequently. It may cause ink leakage.
7. Don’t pull out the connector of cartridge and don’t tear off adhesive tape at the
bottom of cartridge.
Warning:
1. Not drinkable; keep it out reach of children.
2. Avoid exposure to direct sunshine and don’t keep it in high or freezing
temperature.
3. Avoid collision and fallen down.
Loading...