Epson C51CB69060 User Manual

User’s Guide

78 6

2 3

4 5

8 9

English

Read this document carefully to use this product safely and correctly.

Safety Instructions

For your safety, read the attached documents carefully to use this product correctly. After you have read all instructions, keep this manual handy for future reference and to make your concerns clear. Items below indicate safety precautions to protect users, their surroundings and their property from possible injury or damage. Precautionary notations are categorised as follows according to personal injury and damage to the equipment if the instructions are ignored or the equipment is misused.

DANGER

This symbol indicates information that, if ignored, could possibly result in serious or fatal personal injur y. Take extra caution in performing procedures with DANGER headings.

WARNING

This symbol indicates information that, if ignored, could possibly result in serious personal injury or even death due to incorrect handling.

CAUTION

This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.

The following describes the meaning of each symbol used in the precautions.

This indicates an important reminder.

This indicates a prohibited item.

This indicates a mandatory procedure.

DANGER

When handling batteries

If liquid leaking from an alkaline battery gets into your eyes, do not rub your eyes but immediately wash them well with clean water and contact a doctor. Otherwise, it may cause blindness.

WARNING

When using the AC adapter and power cable

Do not use any AC adapter or power cable other than the dedicated AC adapter and power cable. Do not use the AC adapter with other than the speciﬁed voltage also. Otherwise, damage, overheating, ﬁre or electric shock may occur.

Take the following precautions when handling the AC adapter and power cable.

Make sure to avoid octopus wiring.

• Make sure the plug is not dusty before inserting it into

• an outlet.

Insert the plug ﬁrmly into the outlet.

• Do not hold the plug with wet hands.

• Do not pull the power cable when disconnec ting

• the plug. Be sure to hold the plug when disconnecting it.

Do not make any modiﬁcation to the AC adapter or

• power cable.

Do not apply strong shocks to or put a heavy object on

• the AC adapter or power cable.

Do not bend or twist the AC adapter or power cable

• forcibly.

Do not place the AC adapter or power cable near a heater.

•

Do not use any damaged AC adapter or power cable. Otherwise, damage, overheating or smoking may occur, which may result in ﬁre or electric shock.

Do not touch the plug during thunderstorms.

When handling batteries

Keep batteries out of reach of children. They are extremely dangerous if swallowed. Contact a doctor immediately if swallowed.

When using this product

Do not apply any strong force or shocks to the product such as standing on, dropping or hitting it. Otherwise, the product may be broken, which may result in ﬁre or electric shock. If it is damaged, turn off the power immediately, unplug the AC adapter and remove the batteries, and then contact the EPSON customer support centre. Continuous use may result in ﬁre or electric shock .

Take care not to spill any beverage such as tea, coffee or juice onto the product, or to spray aerosol insecticide. It may cause malfunction, ﬁre, or electric shock . If any liquid has been spilled on the product, turn off the power, unplug the AC adapter and remove the batteries immediately, and then contact the EPSON customer suppor t centre. Continuous use may result in ﬁre or electric shock .

Do not touch the printhead because it becomes very hot. Otherwise, there is a risk of burns.

Do not open any covers other than the cover on the rear. Doing so may result in ﬁre or electric shock . Always use the product as instructed in this manual. Otherwise, damage or injury may occur.

If any of the following abnormalities is observed, turn off the power immediately, unplug the AC adapter and remove the batteries, and then contact the EPSON customer support centre.

If smoke, strange odours or unexpected noises come

• from the product

If liquid or foreign objects get inside the product

• If the product has been dropped or damaged

•

If your product is faulty, please read the included warranty card and consult the store you purchased it from. If you require further assistance contact your local EPSON customer support centre.

Please also ﬁnd below the URL for the support centre: http://www.epson.co.uk/support

When handling the cutter

Do not touch the exit slot (where labels come out) during printing or when using the cutter, otherwise there is a risk of injury.

Others

Do not use or store the product, batteries, AC adapter, power cable, or tape cartridges in the following places.

In direct sunlight.

• Where it may become ex tremely hot such as in a

• vehicle with the windows closed.

Where it may become ex tremely hot such as near a

• heater or the temperature becomes very unstable such as near the exhaust duc t of an air conditioner.

Where the product may get wet due to a shower or rain

• such as in a bathroom or outdoors.

In a dusty place or where the product may be exposed

• to smoke or steam such as near the kitchen or a humidiﬁer.

On an unstable place such as on a shak y table or on an

• inclined place.

Where it might be subjected to vibration or shock.

• Near high-voltage power lines or something that

• generates a magnetic ﬁeld.

Keep the plastic bags used to contain the product or this manual out of reach of children. Children may suf focate if they swallow them or put their heads into the bags.

CAUTION

When handling batteries

If liquid leaks from a battery, wipe it of f with a cloth and replace it with a new one. If the liquid comes in contact with your skin, wash it away with water immediately.

If the batteries are used incorrectly, they may cause leakage, overheating, explosion, erosion, or damage to the product, which may result in ﬁre or injury.

Do not use new ones and old batteries together, or mix

• different typ es of batteries.

Use only AAA Alkaline batteries. Rechargeable batteries

• cannot be used.

Use batteries in the correct directions.

• Take the batteries out immediately when they have no

• power remaining.

Take the batteries out if you do not use the product for

• a long time.

Do not heat batteries or throw them in ﬁre or water.

• Do not pinch the batteries with metal tweezers or

• use any pointed sharp metal object such as the tip of a mechanical pen or ball-point pen when taking the batteries out.

When disposing of used batteries, be sure to follow your local regulations.

When using the AC adapter

Do not unplug the AC adapter while the product is in operation, other wise printing may not be successful.

Do not use the AC adapter in a small, conﬁned space, or cover it with a cloth. Otherwise, the AC adapter may overheat and deteriorate.

When using this product

Do not stand on the product or place it on an unstable place such as on a shaky table or on an incline. Otherwise, the product may fall and cause injury.

To ensure safety, unplug this product b efore leaving it unused.

Before cleaning, make sure to unplug the AC adapter from the outlet, and remove the bat teries.

Do not use a moistened cloth or solvents such as alcohol, thinner or benzine.

When handling tape cartridges

Make sure to use a dedicated LC Tape.

• Some types of tape cannot be cut by the cutter. For the details,

• refer to the tape's manual.

Do not drop it or disassemble it. Doing so may cause damage.

• Do not pull out the tape forcibly by hand. But make sure to

• feed the tape with + . Otherwise, the tape cartridge

may be broken and unusable. Avoid using a tape cartridge without remaining tape. Doing so

• may cause overheating of the printhead, which may result in damage or malfunction.

MEMO

Tape cartridges contain ink ribbons in them. When disposing tape car tridges, make sure to follow the local regulations for disposal.

Other cautions

Notes on usage

Operate the keyboard gently.

• Do not touch the printhead.

• Take care not to cut your ﬁngers when cutting the label with

• scissors.

Do not attach a label on human bodies, living things, public

• facilities or other people’s belongings.

About the printed labels

Depending on the environment labels are used in and the

• nature of the object labels are attached to, the following issues may occur: Label : Discolouration, faded characters, peeling Adhesive side: Adhesive residue, staining, damage

Carefully check the suitability of the label for the intended

• purpose before use. EPSON takes no responsibility for any damage or loss due to the above mentioned causes.

Before use

1. Preparing the power supply

This product operates on batteries or with the dedicated AC adapter.

Using on batteries

Prepare six AAA alkaline batteries.

1. Remove the cover on the rear.

2. Insert the batteries.

MEMO

When continuing to install a tape cartridge, leave the cover off and go to Step 2.

3. Close the cover until it snaps into place.

Using with the AC adapter (APT0615Z)

Make sure to use the dedicated AC adapter

(APT0615Z).

1. Connect the AC adapter ﬁrmly into the power socket of the product.

2. Plug the AC adapter into the outlet.

Troubleshooting

Messages

Insert Tape No tape cartridge is installed. Turn the power

Check battery Possible causes for this message are:

Too many lines Text entered is too long.

Seq. num. only 1 Sequence numbers have already been set.

Problems

Does not operate normally.

Initialise this product if it does not operate normally such as the power cannot be turned on or off, or the display is interrupted.

No image comes out even though has been pressed.

Are the batteries correctly set? Check if all the batteries are correctly set.

Did the bat teries run out? Replace the batteries with new ones, or use the dedicated AC adapter (APT0615Z).

Is the AC adapter securely connected? Connect the AC adapter and the power cable ﬁrmly to the power socket of the product, the AC adapter connector and the outlet.

Are you using an AC adapter other than the dedicated one? Using an AC adapter other than the dedicated one (APT0615Z) is very dangerous, and may cause overheating or damage to the electric circuits.

Is the display level appropriate? Adjust the display level.

Display has turned off.

Did you enable the auto power-of f function? The power turns off automatically if no operation is made for more than 5 minutes.

Did you try to carry out a func tion incorrectly? If buttons are operated incorrectly, the display turns off for a moment.

Nothing is printed even though has been pressed.

Is text entered? Nothing is printed if no text is entered.

Any message on the display? Read the message and take the appropriate action.

Did the tap e run out? Install a new tape car tridge.

Did the bat teries run out? Replace the batteries with new ones, or use the dedicated AC adapter (APT0615Z).

Is the cover on the rear open? Set the tap e cartridge correctly and close the cover completely.

off and install a tape cartridge correctly.

No power remaining or inserted in the

• wrong way

Mixed with other types or old ones

•

If so, set the batteries correc tly or replace them with new ones.

Press to delete the lines indicated by the cursor.

Sequence numbers can be used for one par t only.

2. Installing a tape cartridge

1. Remove the slack of the ink ribbon.

2. Remove the cover on the rear.

3. Set the tape cartridge. Press it ﬁrmly until snaps into place.

When installing a new tape or the tip of the tape is longer than usual, put the tape through the "Tape Guide" slot.

Do not press the "Cut Button" before the tape stops.

•

Do not pull the tape out with your ﬁngers.

•

4. Close the cover on the rear until it snaps into place.

How to remove the tape cartridge

Hold the cartridge by the tabs, and lift it straight

up.

3. Turning the power on

1. Press . When changing the language of messages on the display sDisplay Settings ("Display" menu)

Txt too long-OK? Entered text is too long for the speciﬁed

Overheated! The printhead is too hot. Turn the power off

Cover open ! If you open the cover on the rear without

Motor error! An error occurred in the motor operation.

Characters are not printed properly.

Is the tape cartridge correctly set? Set the tap e cartridge correctly.

Is the printhead dirty? Clean the printhead.

Did the bat teries run out? Replace them with new ones, or use the dedicated AC adapter (APT0615Z).

Printing ends in the middle of text.

Did the tap e run out? Install a new tape car tridge.

Did the bat teries run out? Replace them with new ones, or use the dedicated AC adapter (APT0615Z).

Created text has gone.

Did you delete the tex t? If + are pressed, the tex t on the display will be deleted.

Did you initialise the product? If the product is initialised, all the created text will be deleted.

Did you remove the batteries or the AC adapter when the product was in operation? If the AC adapter or the batteries are removed during operation, the text may be deleted.

Cannot attach the label.

Did you peel the backing paper? Attach the label af ter peeling the backing paper.

Are you attaching it on a dirty place or on a place with a rough surface? The label may not adhere due to the material of the at tachment location or the environmental conditions.

MEMO

If none of the above has solved the problem or the symptom is other than the above, contact the EPSON customer support centre.

tape length. Press to print in the correct length.

and take out the tape cartridge. Wait for a while before star t printing again.

turning the power of f, a message is displayed and then the power is turned off automatically.

Turn the power of f once, then turn it back on. If the same message appears, turn the power off and contact the EPSON customer support centre.

4. Feeding the tape

Do not press the "Cut Button" before the tape

stops.

After setting a tape cartridge, make sure to feed tape.

1. Press + .x

2. Press .xx

3. Cut the tape. Cut it by pressing the "Cut Button".

5. Creating a label

Example: ABC

1. Press while holding down to enter text in capital letters.

2. Press the following keys: , ,

"ABC" appears on the display.

Refer below for other operations and the labels you can create with this product. sEditing characters, Useful functions

6. Printing labels

1. Press . The length of the label to print and the number of prints appear, and printing starts.

2. When the tape stops, press the "Cut Button" to cut the tape.

Do not press the "Cut Button" before printing is

complete.

Printing multiple labels continuously

1. Press . The screen to enter the number of prints appears.

2. Enter a value with number buttons and press . The length of the label to print and the number of prints appear, and printing starts.

3. When the tape stops, press the "Cut Button" to cut the tape. A 'cut' mark will be printed. Cut the tape with scissors.

Adjusting print density

1. When the power is off, press + .

2. Adjust print density with , and press .

MEMO

In general, please set the value to the default; "0".

7. Attaching labels

1. Peel off the backing paper.

2. Attach the label and rub it ﬁrmly.

Turn the power off after use.



1. Press .

Batteries:

Take them out if not in use for a long time.

AC adapter:

Disconnect from the outlet and the product.

Editing characters

Press character keys and enter text. sPart Names and Functions Text is entered from the cursor position. sDisplay

To keep the already entered text, ﬁrst move the

cursor to a number to which no text is entered yet with + or + , then enter text.



Switching upper case or lower case

1. Press + .

The setting is indicated on the display. Characters

are set to upper case or lower case.

To capitalise partially: Enter with pressed.

Deleting characters



1. Press .

Deletes one character backward.

Breaking lines



1. Press .

Breaks the line from the character next to the cursor.

Deleting text



1. Press + .

2. When a conﬁrmation message appears, press .

Text will be deleted.

Conﬁrming text



1. Press .

Text appears on the display. You can check the text and the length of the label. But the print image cannot be conﬁrmed.

Adding characters with an accent mark



to the label

If there is a choice of characters with an accent mark, they are indicated on the display. Example: École

1. Press + .

2. Press . A choice of characters with an accent mark appears.

3. Select an item with , and press . Go on and enter the next character.

Characters with an accent mark sSymbol List

Part Names and Functions

1. Power, + : To "Print density" menu.

2. Font

3. Font size

4. Style

5. Setting

6. Character keys

7. Shift

Display

You can check settings on the display. Indicators show whether or not settings are enabled.

1. Font size

2. Font width

3. Frame

4. Font style

5. Vertical

6. Battery level (as a guide)

Initialising this product

The product may stop functioning due to static electricity or other causes. Initialise the product if it does not operate normally such as the display is interrupted.

Initialise the product. Take extreme care before

initialising it. All the created text will be deleted. The settings you made for character input will return to the default.

1. Press .

2. Press and hold + , and press .

3. When a message appears, press . The product will be Initialised. To abort: Press any button other than .

Adding a punctuation mark to the label



Select from the following two methods.

1. Press . Each press shows the next mark.

Available marks

1. Press + . Each press shows the next mark.

Available marks

Adding a symbol to the label



1. Press .

2. When the category appears, select an item with

, and press .

3. When symbols appear, select a symbol with

, and press .

Available symbols sSymbol List

Creating labels with serial numbers



(Sequence number)

1. Press + .

2. Enter a number for the ﬁrst label, and press . The number increases by one whenever printing.

Creating pieces of text



You can create multiple pieces of text continuously. Up to 30 pieces can be created at a time. You can check which piece of text you are creating with the text number mark displayed at the beginning.

Creating another piece of text

1. Select the next text number mark with + or

+ .

You can create another piece of text. Do the same

for the next pieces.

Printing a selected piece of text

1. Select a piece of text you want to print with +

or + .

2. Press .

8. Caps Lock + : Capitalises the entered characters.

9. Accent

10. Space

11. Shift

12. Select/Enter

13. Punctuation: A choice of marks. + : The other choice of marks.

sAdding a punctuation mark to the label

14. Symbol, + : To "Sequence number"

menu.

15. Delete, + : Deletes text.

16. Preview, + : The "Display" menu.

17. Print copies

18. Cursor keys + , + : To the previous or next text.

19. Print, + : Feeds the tape.

20. Cut Button

21. Display

7. Cursor: Indicates the position where the operation

is performed. This is the place where you enter text or delete symbols, etc.

8. Head mark: Indicates what line it is in. Appears

when multiple lines exist.

MEMO

: If this appears, you cannot print anything.

9. Accent mark options

10. Upper case/lower case

11. Text number mark: Indicates the number of the

current text counted from the beginning.

Speciﬁcations

Body



Dimensions Approx. 145 (W) x 150 (D ) x 55 (H) ( mm) Weight Approx. 400g (excluding batteries, tape

Usage conditions



Operating temperature

Storage temperature

cartridge)

10 to 35 degrees C

-10 to 55 degrees C

Useful functions

This section explains various functions that will help you create labels.

Changing the font size



1. Press .

2. Select a line layout with , and press . "Equal": Applies the same font size. No need to

proceed to Step 3.

3. Select a font size with , and press .

Changing the font



1. Press .

2. Select a font with , and press . The font used for the entire text will change.

Applying a font style



1. Press .

2. Select a style with , and press . Styles applied to small or elaborate characters may

not be able to print clearly.

Display Settings ("Display" menu)

The following are the settings to make operation easier.

Contrast

Adjusts the density of the fonts on the display. Value: -5 to +5

Language

Selects the language of the settings and messages on the display. Language : English/Spanish/French/Portuguese-Br/ Portuguese-EU/ Italian/Dutch/German

inch:cm

Selects the unit to indicate the length. Value: inch/cm

Procedure

1. Press + .

2. Select a setting item with , and press .

3. When the options of the selected item appear, select your choice with , and press .

Cleaning

When the exterior is dirty

Wipe the dirt off with a soft cloth. If it is very dirty, use a cloth wrung out of water.

Never use chemicals or solvents such as benzine,

thinner, or alcohol, or use a chemical duster.

When the printhead is dirty

If the print becomes faint or some parts are missing, there may be some dirt on the printhead. Clean the print head with a cotton swab moistened with medical alcohol (commercially available ethanol).

Power supply



AC adapter Type APT0615Z1-1

Manufacturer Input AC100-240V, 0.3A, 50- 60Hz

Output DC6.5V, 1.5A Total output

Batter y AAA alkaline bat tery x 6

Supported tape width



6 mm, 9 mm, 12 mm

Adding a frame



power

1. Press .

2. Select "Frame" with , and press .

3. Select an item with , and press . Entering the frame No. to select does the same.

Available frames sSymbol List

Specifying the label length



1. Press .

2. Select "Label length" with , and press .

3. Select a value with or enter it, and press .

Maximum length: 40cm (15.0 inch) "Auto": Adjusts to the proper length automatically.

Adjusting the space between characters



1. Press .

2. Select "Char. spacing" with , and press .

3. Select an item with , and press .

Making the width of font narrower



1. Press .

2. Select "Narrow" with , and press .

3. Select "Narrow" with , and press .

Lining up characters vertically



1. Press .

2. Select "Vertical" with , and press .

3. Select "On" with , and press .

Using mirror writing for the label



1. Press .

2. Select "Mirror print" with , and press .

3. Select "On" with , and press .

Seiko Epson Corp.

(dedicated adapter, power cable only)

10W