Epson 7700, 7900, 9700, 9900, 9890 Service Manual

...

SERVICE MANUAL

Large Format Color Inkjet Printer

Epson Stylus Pro 7700/7710 Epson Stylus Pro 7700M/7710M Epson Stylus Pro 7900/7910 Epson Stylus Pro 9700/9710 Epson Stylus Pro 9900/9910 Epson Stylus Pro WT7900/WT7910 Epson Stylus Pro 9890/9908 Epson Stylus Pro 7890/7908

Confidential

SEIJ08005

Notice:

mechanical, photocopying, recording, or otherwise, without the prior written permission of SEIKO EPSON CORPORATION.

 The contents of this manual are subject to change without notice.

 All efforts have been made to ensure the accuracy of the contents of this manual. However, should any errors be detected, SEIKO EPSON would greatly

appreciate being informed of them.

 The above not withstanding SEIKO EPSON CORPORATION can assume no responsibility for any errors in this manual or the consequences thereof.

EPSON is a registered trademark of SEIKO EPSON CORPORATION.

General Notice: Other product names used herein are for identification purpose only and may be trademarks or registered trademarks of their

respective owners. EPSON disclaims any and all rights in those marks.

LFP CS Quality Assurance Department

Confidential

PRECAUTIONS

Precautionary notations throughout the text are categorized relative to 1) Personal injury and 2) Damage to equipment.

DANGER Signals a precaution which, if ignored, could result in serious or fatal personal injury. Great caution should be exercised in performing

procedures preceded by DANGER Headings.

WARNING Signals a precaution which, if ignored, could result in damage to equipment.

The precautionary measures itemized below should always be observed when performing repair/maintenance procedures.

DANGER

1. ALWAYS DISCONNECT THE PRODUCT FROM THE POWER SOURCE AND PERIPHERAL DEVICES PERFORMING ANY MAINTENANCE OR REPAIR PROCEDURES.

2. NO WORK SHOULD BE PERFORMED ON THE UNIT BY PERSONS UNFAMILIAR WITH BASIC SAFETY MEASURES AS DICTATED FOR ALL ELECTRONICS TECHNICIANS IN THEIR LINE OF WORK.

3. WHEN PERFORMING TESTING AS DICTATED WITHIN THIS MANUAL, DO NOT CONNECT THE UNIT TO A POWER SOURCE UNTIL INSTRUCTED TO DO SO. WHEN THE POWER SUPPLY CABLE MUST BE CONNECTED, USE EXTREME CAUTION IN WORKING ON POWER SUPPLY AND OTHER ELECTRONIC COMPONENTS.

4. WHEN DISASSEMBLING OR ASSEMBLING A PRODUCT, MAKE SURE TO WEAR GLOVES TO AVOID INJURY FROM METAL PARTS WITH SHARP EDGES.

WARNING

1. REPAIRS ON EPSON PRODUCT SHOULD BE PERFORMED ONLY BY AN EPSON CERTIFIED REPAIR TECHNICIAN.

2. MAKE CERTAIN THAT THE SOURCE VOLTAGES IS THE SAME AS THE RATED VOLTAGE, LISTED ON THE SERIAL NUMBER/RATING PLATE. IF THE EPSON PRODUCT HAS A PRIMARY AC RATING DIFFERENT FROM AVAILABLE POWER SOURCE, DO NOT CONNECT IT TO THE POWER SOURCE.

3. ALWAYS VERIFY THAT THE EPSON PRODUCT HAS BEEN DISCONNECTED FROM THE POWER SOURCE BEFORE REMOVING OR REPLACING PRINTED CIRCUIT BOARDS AND/OR INDIVIDUAL CHIPS.

4. IN ORDER TO PROTECT SENSITIVE MICROPROCESSORS AND CIRCUITRY, USE STATIC DISCHARGE EQUIPMENT, SUCH AS ANTI-STATIC WRIST STRAPS, WHEN ACCESSING INTERNAL COMPONENTS.

5. REPLACE MALFUNCTIONING COMPONENTS ONLY WITH THOSE COMPONENTS BY THE MANUFACTURE; INTRODUCTION OF SECONDSOURCE ICs OR OTHER NON-APPROVED COMPONENTS MAY DAMAGE THE PRODUCT AND VOID ANY APPLICABLE EPSON WARRANTY.

6. WHEN AIR DUSTER IS USED ON THE REPAIR AND THE MAINTENANCE WORK, THE USE OF THE AIR DUSTER PRODUCTS CONTAINING THE INFLAMMABLE GAS IS PROHIBITED.

Confidential

About This Manual

This manual describes basic functions, theory of electrical and mechanical operations, maintenance and repair procedures of the printer. The instructions and procedures included herein are intended for the experienced repair technicians, and attention should be given to the precautions on the preceding page.

Manual Configuration

This manual consists of six chapters and Appendix.

CHAPTER 1.PRODUCT DESCRIPTIONS

Provides a general overview and specifications of the product.

CHAPTER 2.OPERATING PRINCIPLES

Describes the theory of electrical and mechanical operations of the product.

CHAPTER 3.TROUBLESHOOTING

Describes the step-by-step procedures for the troubleshooting.

CHAPTER 4.DISASSEMBLY / ASSEMBLY

Describes the step-by-step procedures for disassembling and assembling the product.

CHAPTER 5.ADJUSTMENT

Provides Epson-approved methods for adjustment.

CHAPTER 6.MAINTENANCE

Provides preventive maintenance procedures and the lists of Epson-approved lubricants and adhesives required for servicing the product.

CHAPTER 7.Epson Stylus Pro 7700M/7710M (Copy Mode)

Describes the copy mode features and basic specifications of Epson Stylus Pro 7700M/7710M

CHAPTER 8.APPENDIX

Provides the following additional information for reference:  Connectors  Panel Menu Maps  ASP List  Exploded Diagrams

Confidential

Symbols Used in this Manual

Lubrication

Various symbols are used throughout this manual either to provide additional information on a specific topic or to warn of possible danger present during a procedure or an action. Be aware of all symbols when they are used, and always read NOTE, CAUTION, or WARNING messages.

Indicates an operating or maintenance procedure, practice or condition that is necessary to keep the products quality.

Indicates an operating or maintenance procedure, practice, or condition that, if not strictly observed, could result in damage to, or destruction of, equipment.

May indicate an operating or maintenance procedure, practice or condition that is necessary to accomplish a task efficiently. It may also provide additional information that is related to a specific subject, or comment on the results achieved through a previous action.

Indicates an operating or maintenance procedure, practice or condition that, if not strictly observed, could result in injury or loss of life.

Indicates that a particular task must be carried out according to a certain standard after disassembly and before re-assembly, otherwise the quality of the components

in question may be adversely affected.

Lubrication

Indicates that lubrication is needed for the parts after disassembly, when doing a maintenance or replacing a part with a new one.

Confidential

Revision Status

Revision Date of Issue Description

A October 20, 2008 First release

B November 25, 2008 Full-fledged revision

Revised

 All chapters

 Various cautions have been added and some wrong mentions have been corrected.

 Chapter 1

 "1.5.2 Maintenance Mode" (p.73) : setting value for roll paper tension has been added.

 Chapter 3

 "3.3 Remedies for Error Messages" (p.113) : trouble shooting related to SpectroProofer has been added.

 "Mechanical Adjustment" mentioned in the service calls descriptions has been deleted.

 Chapter 4

 Some structure diagrams have been revised.

 "4.4.4.9 Carriage Unit" (p.248) : adjustments have been revised.

C March 27, 2009

 "4.4.6 Ink System Mechanism" (p.266) : ink discharging method has been added.

 "4.4.7 Auto Take-up Reel" (p.313) : procedure has been added.

 Chapter 5

 "5.4.5 Printhead Slant Adjustment (PF)" (p.381) : adjustments have been revised.

 "5.4.9 Absorber Position Check" (p.398) : illustration has been added in the adjustment pattern.

 "5.5.2 Skew Check" (p.406) : caution has been added.

 "5.7.2 Input CR/PF Motor Current" (p.419) : picture of the label has been added.

 "5.7.7 Cut Position Adjustment" (p.425) : procedure has been revised.

 "5.8 Clear Counters" (p.427) : SpectroProofer counters have been added in the clear counter menu list.

 Adjustment media types have been corrected.

 Chapter 6

 "6.2.2 Storing the Printer and Cleaning the Ink Path" (p.447) : procedure has been added.

Confidential

Revision Date of Issue Description

Revised

 All chapters

 Information of Epson Stylus Pro 7700/Epson Stylus Pro 7710/Epson Stylus Pro 9700/Epson Stylus Pro 9710 has been added.

 Chapter 1

 "1.2.6 Auto Take-up Reel Unit" (p.26) : added

 "1.2.5 Reliability/Durability" (p.24) : revised

 "1.3.2.2 Designated Paper" (p.29) : information about roll paper tension and take-up has been added.

 Chapter 3

 "3.3 Remedies for Error Messages" (p.113) : error has been added.

 "3.5 Remedies for Maintenance Requests" (p.129) : "request no. 0010" and "4000" have been added.

 "3.6 Remedies for Service Call Error" (p.131) : "error code Dxxx" has been added.

 "3.7 Remedies for Print Quality Troubles" (p.149) : information has been added.

 Chapter 4

D September 18, 2009

 "4.1.5 Differences of the parts/components between models" (p.172) : newly added.

 "4.4.6.3 Printhead" (p.270) : adjustments have been added.

 "4.4.6.5 Ink Cartridge Holder R" (p.277), "4.4.6.6 Ink Cartridge Holder L" (p.284) : adjustments have been revised.

 "4.4.6.5 Ink Cartridge Holder R" (p.277), "4.4.6.6 Ink Cartridge Holder L" (p.284) : procedure has been revised.

 "4.4.6.12 Ink Tube R" (p.306), "4.4.6.13 Ink Tube L" (p.310) : reassembly has been added.

 "4.4.8.7 Main Board" (p.332) : adjustments have been revised.

 Chapter 5

 "5.1.4 Tools for Adjustments" (p.357) : revised.

 "5.1.5 Service Program Basic Operations" (p.358) : information has been added.

 "5.4.1 Head Rank ID" (p.374) : caution has been added.

 "5.6.1 AID Function check" (p.416) : caution has been added.

 "5.7.4 Installing Firmware" (p.421) : caution has been added.

 Chapter 6

 "6.5 Lubrication" (p.452) : lubrication points list has been revised.

 "6.5 Lubrication" (p.452) : information of lubrication amount has been added.

Confidential

Revision Date of Issue Description

Revised

 All chapters

 Information of Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 has been added.

 Chapter 1

 Information for Epson Stylus Pro WT7900/Epson Stylus Pro WT7910, ClearProof Film and basket for Epson Special Film have been added.

 Chapter 3

 Errors for Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 have been added.

 "3.7 Remedies for Print Quality Troubles" (p.149) : troubleshooting information of Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 and related to ClearProof Film have been added.

E October 13, 2009

 Chapter 4

 "4.1.5 Differences of the parts/components between models" (p.172) : Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 has been added.

 Chapter 5

 Information of Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 has been added.

 "5.4.1 Head Rank ID" (p.374) : Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 has been added in caution.

 "5.4.2 Head Cleaning" (p.376) : information about cleaning has been newly added for Epson Stylus Pro WT7900/Epson Stylus Pro WT7910.

 Information about adjustment has been added (Premium Glossy Photo Paper (250) must be used for Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 when adjustment).

 Chapter 7

 "8.2 Panel Menu Map" (p.468) : panel menu map of Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 has been added.

Confidential

Revision Date of Issue Description

Revised

 Chapter 1

 "1.2.1 Basic Specifications" (p.20) : nozzle configuration has been revised.

 "1.3.3 Printable Area" (p.41) : minimum for roll paper width has been revised.

 "1.5.3 Serviceman Mode" (p.74) : "CL5" in "C/D" column in "Cleaning" menu of Epson Stylus Pro WT7900/Epson Stylus Pro WT7910 has been added.

 Chapter 3

 "3.6 Remedies for Service Call Error" (p.131) : error information for 1427 and 1428 has been revised, remedies for 1A51 to 1A53, 1A39 and 1A40 have been revised.

 "3.7.2.2 Cautions for using white ink" (p.153) : newly added.

F February 12, 2009

 Chapter 4

 "4.4.6.1 Ink System Unit" (p.266) : caution about Wiper Cleaner Assy when replacing the Ink System Unit has been added.

 "4.4.6.5 Ink Cartridge Holder R" (p.277) etc. : part number for "SEAL RUBBER, JOINT, ASP" has been revised.

 "4.4.6.5 Ink Cartridge Holder R" (p.277) etc. : FFC installation method in reassembly has been added.

 Chapter 5

 "5.1.5 Service Program Basic Operations" (p.358) : caution for saving destination for Service Program has been added.

 "5.3.1 CR Timing Belt Tension Adjustment" (p.364) etc. : model number for sonic tension meter has been revised, input values have been revised.

 "5.7.8 Ink Holder Adjustment" (p.426) : caution not to insert the ink cartridges before the adjustment has been added.

 Chapter 7

 "8.2 Panel Menu Map" (p.468) : added and revised for all models.

 "8.5 Exploded Diagram" (p.490) : revised.

Revised

 All chapters

 Information of Epson Stylus Pro 7700M/7710M has been added.

 Chapter 1

 "1.2.2 Electric Specifications" (p.21) : correction of Electric Specifications

 "1.2.5 Reliability/Durability" (p.24) : correction

 Chapter 3

G May 20, 2010

 "3.2 List of Error Messages" (p.107) : messages in copy mode of Epson Stylus Pro 7700M/7710M have been added.

 "3.3 Remedies for Error Messages" (p.113) : troubleshooting information related to the copy mode of Epson Stylus Pro 7700M/7710M

has been added.

 Chapter 7

 " Epson Stylus Pro 7700M/7710M (Copy Mode)" (p.459) : newly added.

 Chapter 8

 " APPENDIX" (p.465) : moved from Chapter 7.

 "8.2 Panel Menu Map" (p.468) : panel menu map of Epson Stylus Pro 7700M/7710M has been added.

Confidential

Revision Date of Issue Description

Revised

 All chapters

 Information of Epson Stylus Pro 7890/7908/9890/9908 has been added.

 Chapter 4

H October 8, 2010

 "4.4.6.7 Ink Holder Board Assy L" (p.290) : newly added.

 "4.4.6.8 Ink Holder Board Assy R" (p.292) : newly added.

 "4.4.6.9 AID Board" (p.294) : procedure has been added due to change in shape.

 Chapter 5

 "5.5.4 T&B&S Adjustment" (p.409) : correction.

Confidential

Revision Date of Issue Description

Revised

 Chapter 1

 "1.2.1 Basic Specifications" (p.20) : Resolution of 7700/7710/770M/7710M/9700/9710 has been changed.

 "1.2.5 Reliability/Durability" (p.24): Life of ink tube used for Pro7890/7908 has been revised. / Cutter life was revised.

 Chapter 3

 "3.2 List of Error Messages" (p.107): Some messages have been changed.

 "3.3 Remedies for Error Messages" (p.113): Some messages have been changed.

 "3.4 Remedies for Error Messages related to SpectroProofer/Auto Take-up Reel" (p.123): Error 80 was added.

 "3.5 Remedies for Maintenance Requests" (p.129): Maintenance call 8000 was added.

 "3.6 Remedies for Service Call Error" (p.131): Service call error 1488 was added. / Service call error D131 was revised.

 Chapter 4

 "4.1.1 Precautions" (p.167): Type of the lithium battery has been added. / Cautions have been added.

 "4.1.5.2 Identification method for the parts/components between models" (p.182): Identification information for PUMP,CAP ASSY,ESL,ASP has been added.

 "4.4.2.9 Front Cover (Middle)" (p.213): Figure (location of washers) in "Caution" has been changed.

I January 13, 2012

 "4.4.6.5 Ink Cartridge Holder R" (p.277): Some figures have been added, and some information has been deleted.

 "4.4.6.6 Ink Cartridge Holder L" (p.284): Some figures have been added, and some information has been deleted.

 "4.4.6.7 Ink Holder Board Assy L" (p.290): "Adjustment" was added.

 "4.4.6.8 Ink Holder Board Assy R" (p.292): "Adjustment" was added.

 "4.4.6.11 Ink Selector" (p.300): "Check point" was added.

 Chapter 5

 "5.1.2 Adjustment Items and the Order by Repaired Part" (p.353): Ink Holder Board Assy was added.

 "5.1.4 Tools for Adjustments" (p.357): Information has been added.

 "5.3.3 Head PG Adjustment" (p.369): revised.

 "Figure 5-31. Determination of Visual Check Pattern" (p.379): revised.

 "5.4.8 Colorimetric Calibration (Color ID) with SpectroProofer" (p.385): revised.

 "5.5.3 Band Feed" (p.407): revised.

 "5.5.4 T&B&S Adjustment" (p.409): revised.

 "5.7.2 Input CR/PF Motor Current" (p.419): revised.

 "5.7.6 Input MAC Address" (p.424): revised.

 "5.7.8 Ink Holder Adjustment" (p.426): revised.

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

Contents

Chapter 1 PRODUCT DESCRIPTION

1.1 Product Description ............................................................................................ 16

1.2 Basic Specifications ............................................................................................ 20

1.2.1 Basic Specifications ................................................................................... 20

1.2.2 Electric Specifications ............................................................................... 21

1.2.3 Ink Specifications ...................................................................................... 22

1.2.4 General Specifications ............................................................................... 23

1.2.5 Reliability/Durability ................................................................................. 24

1.2.6 Auto Take-up Reel Unit ............................................................................. 26

1.3 Printing Specifications ........................................................................................ 27

1.3.1 Paper Feed Specifications .......................................................................... 27

1.3.2 Paper Specification .................................................................................... 27

1.3.3 Printable Area ............................................................................................ 41

1.3.4 Borderless Printing Specification .............................................................. 42

1.3.5 Cutting of Roll Paper ................................................................................. 43

1.4 Hardware Specifications ..................................................................................... 44

1.4.1 Dimensions and Weight ............................................................................. 44

1.4.2 Part Names ................................................................................................. 46

1.4.3 Option Correspondence Table ................................................................... 47

1.5 Control Panel ...................................................................................................... 48

1.5.1 Menu Mode Settings .................................................................................. 58

1.5.2 Maintenance Mode .................................................................................... 73

1.5.3 Serviceman Mode ...................................................................................... 74

Chapter 2 OPERATING PRINCIPLES

2.1 Main Body .......................................................................................................... 95

2.1.1 Housing ...................................................................................................... 95

2.1.2 Electric Circuit Components ...................................................................... 96

2.1.3 Carriage Mechanism .................................................................................. 97

2.1.4 APG Mechanism ........................................................................................ 98

2.1.5 Paper Feed Mechanism .............................................................................. 99

2.1.6 Ink System ............................................................................................... 100

2.2 Options ............................................................................................................. 103

2.2.1 Auto Take-up Reel ................................................................................... 103

2.2.2 SpectroProofer ......................................................................................... 104

Chapter 3 TROUBLE SHOOTING

3.1 Overview .......................................................................................................... 106

3.1.1 Preliminary Check ................................................................................... 106

3.1.2 Troubleshooting Procedure ...................................................................... 106

3.2 List of Error Messages ..................................................................................... 107

3.3 Remedies for Error Messages ........................................................................... 113

3.4 Remedies for Error Messages related to SpectroProofer/Auto Take-up Reel .. 123

3.5 Remedies for Maintenance Requests ............................................................... 129

3.6 Remedies for Service Call Error ...................................................................... 131

3.7 Remedies for Print Quality Troubles ................................................................ 149

3.7.1 Remedies for Print Quality Troubles ....................................................... 149

3.7.2 Remedies for Print Quality Troubles when Using Epson Stylus Pro WT7900/

WT7910 ................................................................................................... 152

Chapter 4 DISASSEMBLY & ASSEMBLY

4.1 Overview .......................................................................................................... 167

4.1.1 Precautions ............................................................................................... 167

4.1.2 Orientation Definition .............................................................................. 169

4.1.3 Recommended Tools ............................................................................... 170

4.1.4 Cautions when replacing the Main Board Assy/Power Supply Board Assy .. 171

4.1.5 Differences of the parts/components between models ............................ 172

4.2 Parts Diagram ................................................................................................... 188

4.3 Disassembly Flowchart .................................................................................... 195

4.4 Disassembly and Assembly Procedure ............................................................. 201

4.4.1 Special operation for servicing ................................................................ 201

4.4.2 Housing .................................................................................................... 203

4.4.3 Electric Circuit Components ................................................................... 228

4.4.4 Carriage Mechanism ................................................................................ 236

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

4.4.5 Paper Feed Mechanism ............................................................................ 250

4.4.6 Ink System Mechanism ............................................................................ 266

4.4.7 Auto Take-up Reel ................................................................................... 313

4.4.8 SpectroProofer ......................................................................................... 325

Chapter 5 ADJUSTMENT

5.1 Overview .......................................................................................................... 352

5.1.1 Precautions ............................................................................................... 352

5.1.2 Adjustment Items and the Order by Repaired Part .................................. 353

5.1.3 Description of Adjustments ..................................................................... 355

5.1.4 Tools for Adjustments ............................................................................. 357

5.1.5 Service Program Basic Operations .......................................................... 358

5.2 NV-RAM BACKUP UTILITY ........................................................................ 363

5.3 CR Related Adjustment .................................................................................... 364

5.3.1 CR Timing Belt Tension Adjustment ...................................................... 364

5.3.2 CR Encoder Sensor Adjustment .............................................................. 368

5.3.3 Head PG Adjustment ............................................................................... 369

5.3.4 Cleaning PG Adjustment ......................................................................... 372

5.4 Head Related Adjustments ............................................................................... 374

5.4.1 Head Rank ID .......................................................................................... 374

5.4.2 Head Cleaning ......................................................................................... 376

5.4.3 Nozzle Check ........................................................................................... 377

5.4.4 Printhead Slant Adjustment (CR) ............................................................ 378

5.4.5 Printhead Slant Adjustment (PF) ............................................................. 381

5.4.6 Auto Uni-D Adjustment .......................................................................... 383

5.4.7 Auto Bi-D Adjustment ............................................................................. 384

5.4.8 Colorimetric Calibration (Color ID)

with SpectroProofer ................................................................................. 385

5.4.9 Absorber Position Check ......................................................................... 398

5.4.10 Ink Mark Sensor Height Adjustment ..................................................... 399

5.4.11 Ink Mark Sensor Adjustment ................................................................. 400

5.4.12 Air Leak Check for Ink Supply System ................................................. 401

5.4.13 Initial Ink Charge Flag ON/OFF ............................................................ 403

5.4.14 Initial Ink Charge ................................................................................... 403

5.5 PF Related Adjustment ..................................................................................... 404

5.5.1 PF Timing Belt Tension Adjustment ....................................................... 404

5.5.2 Skew Check ............................................................................................. 406

5.5.3 Band Feed ................................................................................................ 407

5.5.4 T&B&S Adjustment ................................................................................ 409

5.5.5 Paper Thickness Sensor Position Adjustment ......................................... 411

5.5.6 PF Encoder Sensor Adjustment ............................................................... 414

5.5.7 Rear Sensor AD Adjustment ................................................................... 415

5.6 AID Related Adjustment .................................................................................. 416

5.6.1 AID Function check ................................................................................. 416

5.7 Other Adjustment ............................................................................................. 418

5.7.1 Setting Destination .................................................................................. 418

5.7.2 Input CR/PF Motor Current ..................................................................... 419

5.7.3 RTC and USB ID ..................................................................................... 420

5.7.4 Installing Firmware .................................................................................. 421

5.7.5 Input Serial Number ................................................................................ 423

5.7.6 Input MAC Address ................................................................................. 424

5.7.7 Cut Position Adjustment .......................................................................... 425

5.7.8 Ink Holder Adjustment ............................................................................ 426

5.8 Clear Counters .................................................................................................. 427

5.9 Tests .................................................................................................................. 428

5.9.1 Network Communication Check ............................................................. 428

5.9.2 Suction Fan Operation Check .................................................................. 428

5.9.3 Color LCD Display Check ...................................................................... 429

5.9.4 Button Operation Check .......................................................................... 429

5.9.5 Inspection of the SpectroProofer ............................................................. 430

5.10 Check Adjustments Results ............................................................................ 443

Chapter 6 MAINTENANCE

6.1 Overview .......................................................................................................... 445

6.2 Setting Up/Storing the Printer .......................................................................... 447

6.2.1 Setting Up ................................................................................................ 447

6.2.2 Storing the Printer and Cleaning the Ink Path ......................................... 447

6.3 Transportation .................................................................................................. 449

6.4 Cleaning ............................................................................................................ 450

6.5 Lubrication ....................................................................................................... 452

Chapter 7 Epson Stylus Pro 7700M/7710M (Copy Mode)

7.1 Overview .......................................................................................................... 460

7.2 Basic Specifications ......................................................................................... 461

7.2.1 Scanning Specifications ........................................................................... 461

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

7.3 Printing Specifications ...................................................................................... 461

7.4 Copy Mode ....................................................................................................... 462

Chapter 8 APPENDIX

8.1 Block Wiring Diagram ..................................................................................... 466

8.1.1 Main Body ............................................................................................... 466

8.1.2 Auto Take-up Reel ................................................................................... 467

8.1.3 SpectroProofer ......................................................................................... 467

8.2 Panel Menu Map ............................................................................................... 468

8.2.1 Epson Stylus Pro 7900/7910/9900/9910/7890/7908/9890/9908 ............. 468

8.2.2 Epson Stylus Pro 7700/7710/7700M/7710M/9700/9710 ........................ 471

8.2.3 Epson Stylus Pro WT7900/WT7910 ....................................................... 474

8.2.4 Epson Stylus Pro 7700M/7710M (Copy Mode) ...................................... 477

8.3 Part names used in this manual ........................................................................ 479

8.4 Parts List ........................................................................................................... 481

8.5 Exploded Diagram ............................................................................................ 490

Confidential

PRODUCT DESCRIPTION

C H A P T E R

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.1 Product Description

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/ WT7900/WT7910/9890/9908/7890/7908 is a wide-format color inkjet printer that supports up to 44 inch-wide (Super B0)/24 inch-wide (Super A1) paper. The main features are;

 Supports very large-sized paper

Maximum available paper width:

Epson Stylus Pro 9700/9710/9900/9910

9890/9908: 1,118 mm (44 inch)

Epson Stylus Pro 7700/7710/7700M/7710M/

7900/7910/WT7900/WT7910 7890/7908: 610 mm (24 inch)

 Ink configuration

 Epson Stylus Pro 7900/7910/9900/9910

Installs the following 11 ink cartridges including newly developed colors; orange and green. The ink selector function is equipped, and black ink can be switched between Photo Black and Matte Black depending on media type.

Table 1-1. Ink Colors (Epson Stylus Pro 7900/7910/9900/9910)

Color Abbreviation

Photo Black PK

Matte Black MK

Cyan C

Vivid Magenta VM

Yellow Y

Orange O

Green G

Light Cyan LC

Vivid Light Magenta VLM

Light Black LK

Light Light Black LLK

 Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910

Consists of the following 5 colors. Switching between photo Black and Matte Black by the ink selector is not necessary, because ink is assigned in colors by nozzles.

Table 1-2. Ink Colors (Epson Stylus Pro 7700/7710/7700M/7710M/9700/9710)

Color Abbreviation

Photo Black PK

Matte Black MK

Cyan C

Vivid Magenta VM

Yellow Y

 Epson Stylus Pro WT7900/WT7910

Consists of the following 9 colors including newly developed white. When the white ink is not necessary to use, it can be changed to cleaning liquid to protect the printhead.

Table 1-3. Ink Colors (Epson Stylus Pro WT7900/WT7910)

Color Abbreviation

Photo Black PK

White WT

Cyan C

Vivid Magenta VM

Yellow Y

Orange O

Green G

Light Cyan LC

Vivid Light Magenta VLM

Cleaning Liquid CL

PRODUCT DESCRIPTION Product Description 16

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

 Epson Stylus Pro 9890/9908/7890/7908

Consists of the following 9 colors. The ink selector function is equipped, and black ink can be switched between Photo Black and Matte Black depending on media type.

Table 1-4. Ink Colors (Epson Stylus Pro 9890/9908/7890/7908)

Color Abbreviation

Photo Black PK

Matte Black MK

Cyan C

Vivid Magenta VM

Yellow Y

Light Cyan LC

Vivid Light Magenta VLM

Light Black LK

Light Light Black LLK

 Super high print quality

Achieves high quality printing, resolution of up to 2880 x 1440 dpi, and variable dot sizes (minimal 3.5 picoliter)

 Lower running cost

 Borderless print is supported

 The latest-type RIP

Supports software RIP made by other companies

 Copy function (Epson Stylus Pro 7700M/7710M only)

Epson Stylus Pro 7700M/7710M offers the following functions with the scanner (GT-2500) connected in addition to the functions of Epson Stylus Pro 7700/7710.

 Enlarge copy

Enlarges the image scanned by the scanner and prints the enlarged image.

 User interface

Copying can be started with one touch of the [OK] button on Epson Stylus Pro 7700M/7710M or the [Start] button on the scanner.

 Printing from a PC

Epson Stylus Pro 7700/7710 automatically switches to the print mode when it receives a print job from a host computer.

 Employs super high-capacity independent ink cartridges

 Equips the on-demand cleaning function without excessive suction of ink

using the independent ink suction system for every two rows and the AID function

 Media handling

 Supports a variety of media

 Spindle-less makes roll paper handling easier

 Paper basket comes as standard

 Stores roll paper usage history and updates it automatically by reading a

barcode. This enables automatic detection of remaining amount of the paper.

 Equips high speed auto cutter for roll paper

PRODUCT DESCRIPTION Product Description 17

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

 Nozzle set configuration

1 2 3 4 5 6 7 8 9 10

Epson Stylus Pro 7900/ 7910/9900/ 9910

Epson Stylus Pro 7700/ 7710/7700M/ 7710M/9700/ 9710

Epson Stylus Pro WT7900/ WT7910

Epson Stylus Pro 9890/ 9908/7890/ 7908

Note : 1-row starting from the left facing the front of the printer.

C VM

C VM Y PK MK MK PK Y VM C

C VM

PK/ MK

WT/

PK/ MK

GY O G LGY Y VLM LC

CL O G PK Y VLM LC

GY --- --- LGY Y VLM LC

 Ink configuration

1 2 3 4 5 6 7 8 9 10 11

Epson Stylus Pro 7900/7910/ 9900/9910

Epson Stylus Pro 7700/ 7710/7700M/ 7710M/9700/ 9710

Epson Stylus Pro WT7900/ WT7910

Epson Stylus Pro 9890/9908/ 7890/7908

Note : 1-row starting from the left facing the front of the printer.

C O Y LC MK PK VM GY G LGY VLM

VM C PK Y MK --- --- --- --- --- ---

C O Y LC WT CL VM CL G PK VLM

C --- Y LC MK PK VM GY --- LGY VLM

 Options

The following options are available.  Auto Take-up Reel (Epson Stylus Pro 9700/9710/9900/9910/

Winds the roll paper automatically

 SpectroProofer

(Epson Stylus Pro 7900/7910/9900/9910/WT7900/WT7910/9890/9908/7890/ 7908 only) Enables color measurement after printing

9890/9908

only)

PRODUCT DESCRIPTION Product Description 18

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

 SpectroProofer (Option)

 Mounting the SpectroProofer equipped with the drying function makes

automatic color measurement after printing available.

 Full-fledged spectrophotometer realizes high precision color measurement.

 Selectable from specifications with/without the UV filter, which enables the

users to configure colorimetric system adjusted with their workflow

 Cooling fans for drying ink stabilizes color in less than 2 minutes.

 Paper pressing function prevents degrading precision of colorimetry caused

by floating of paper.

 Selectable from the white backing or the black backing

Figure 1-1. External View (Main body)

Figure 1-2. External View (SpectroProofer)

PRODUCT DESCRIPTION Product Description 19

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.2 Basic Specifications

1.2.1 Basic Specifications

Specification

Item

Epson Stylus Pro 7900/7910/9900/9910

Print method On-demand inkjet

Black system: 360 nozzles x three colors (Photo black/Matte black, Light black, Light light black)

Nozzle configuration

Color system: 360 nozzles x seven colors (Cyan, Light Cyan, Vivid magenta, Vivid light magenta, Yellow, Orange, Green)

Printing direction

Maximum resolution 2,880dpi x 1,440dpi 1,440dpi x 1,440dpi 2,880dpi x 1,440dpi

Control code ESC/P2, ESC/P3 (commands are nondisclosure)

Paper feed method Friction

RAM 256 MB for Main, 64 MB for Network

Interface

Epson Stylus Pro 7700/7710/7700M/

7710M/9700/9710

Black system: 360 nozzles x two rows x two colors (Photo black, Matte black)

Color system: 360 nozzles x two rows x three colors (Cyan, Vivid magenta, Yellow)

Bi-directional shortest-direction printing

(high-speed return, high-speed skip)

USB 2.0 High Speed

Ethernet 10/100

Epson Stylus Pro WT7900/WT7910 Epson Stylus Pro 9890/9908/7890/7908

Black system: 360 nozzles x one row x one color (Photo black) White system: 360 nozzles x one row x one color

Color system: 360 nozzles x seven colors (Cyan, Light Cyan, Vivid magenta, Vivid light magenta, Yellow, Orange, Green) Maintenance liquid: 360 nozzles x 1

Black system: 360 nozzles x three colors (Photo black/Matte black, Light black, Light light black)

Color system: 360 nozzles x five colors (Cyan, Light Cyan, Vivid magenta, Vivid light magenta, Yellow)

PRODUCT DESCRIPTION Basic Specifications 20

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.2.2 Electric Specifications

Item Specification

Rated voltage 100 to 240 VAC

Input voltage range 90 to 264 VAC

Rated frequency 50 to 60 Hz

Input frequency range 49.5 to 60.5 Hz

Rated current 1.0 A to 0.5 A

Epson Stylus Pro 9900/9910

Epson Stylus Pro 7900/7910

Epson Stylus Pro 9700/9710

Epson Stylus Pro WT7900/

Power consumption

Insulation resistance 10MΩ or more (between AC line and chassis at 500 VDC)

Dielectric strength

WT7910

Epson Stylus Pro 7700/7710

Epson Stylus Pro 7700M/7710M

Epson Stylus Pro 9890/9908

Epson Stylus Pro 7890/7908

Operating: Approx. 80 W Sleep mode: Approx. 16 W or less Standby: Approx. 1 W or less

Operating: Approx. 70 W Sleep mode: Approx. 16 W or less Standby: Approx. 1 W or less

Operating: Approx. 85 W Sleep mode: Approx. 14 W or less Standby: Approx. 1 W or less

Operating: Approx. 60 W Sleep mode: Approx. 14 W or less Standby: Approx. 1 W or less

Operating: Approx. 80 W Sleep mode: Approx. 14 W or less Standby: Approx. 1 W or less

Operating: Approx. 80 W Sleep mode: Approx. 16 W or less Standby: Approx. 1 W or less

Operating: Approx. 70 W Sleep mode: Approx. 16 W or less Standby: Approx. 1 W or less

1.0 kVrms AC for 1 min. or 1.2 kVrms AC for 1 sec. (between AC line and chassis)

Item Specification

Leek current 0.25 mA or less

Conforms to International Energy Star Program

Compliance with regulations

(Category: the harmonic restraint measure guideline)

Conforms to VCCI Class B (with full options installed)

PRODUCT DESCRIPTION Basic Specifications 21

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.2.3 Ink Specifications

Specification

Item

Form Exclusive ink cartridge

Pigment Ink colors

Cartridge life By the date written on the package or the cartridge (at normal temperature)

Guaranteed life after installation

Uninstalled (packed)

Storage

Capacity 350 ml/700 ml 150 ml/350 ml/700 ml

Dimensions

Maintenance Tank C12C890191 / C12C890193 C12C890501 / C12C890502 C12C890191 / C12C890193 C12C890191 / C12C890193

Installed

Transporting (packed)

150 ml N/A 40 (W) x 240 (L) x 107 (H)

350 ml 40 (W) x 240 (L) x 107 (H)

700ml 40 (W) x 320 (L) x 107 (H)

Epson Stylus Pro 7900/7910/9900/9910

Black system: Photo black, Matte black, Light black, Light light black

Color system: Cyan, Light Cyan, Vivid magenta, Vivid light magenta, Yellow, Orange, Green

Epson Stylus Pro 7700/7710/7700M/

7710M/9700/9710

Black system: Photo black, Matte black

Color system: Cyan, Vivid magenta, Yellow

Within 6 months after mounted in the printer

-20 to 40 °C

(within 1 month under 40 °C)

-20 to 40°C

(within 1 month under 40 °C)

-20 to 60 °C

(within 72 hours under 60 °C, and within 1 month under 40 °C)

Epson Stylus Pro WT7900/WT7910 Epson Stylus Pro 9890/9908/7890/7908

Black system: Photo black

White system: White

Color system: Cyan, Light Cyan, Vivid magenta, Vivid light magenta, Yellow, Orange, Green

Maintenance system: Cleaning Liquid

Black system: Photo black, Matte black, Light black, Light light black

Color system: Cyan, Light Cyan, Vivid magenta, Vivid light magenta, Yellow

C A U T I O N

 Ink will be frozen if left under below -15°C circumstances for a

long time. In such a case, leave it in the room temperature more than 4 hours to melt the frozen ink before using it. (no condensation)

 Never disassemble ink cartridges or refill ink in them.

PRODUCT DESCRIPTION Basic Specifications 22

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.2.4 General Specifications

Item Specification

Operating: 10 to 35 °C

Storage (before unpacked): -20 to 60 °C

Temperature

Humidity

(within 120 hours under 60 °C, and within 1 month under 40 °C)

Storage (after unpacked): -20 to 40 °C (within 1 month under 40°C)

Operating: 20 to 80% (no condensation)

Storage (before unpacked):

-20 to 85% (no condensation)

Storage (after unpacked): 5 to 85% (no condensation)

Humidity (%)

Temperature (°C)

PRODUCT DESCRIPTION Basic Specifications 23

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.2.5 Reliability/Durability

 Main Body

Specification

Item

Operating life of the printer

Cutter life (reference)

RTC backup battery*

Pump Cap motor

Parts life

CR motor*, Drive pulley*, Carriage unit*, FFC*

Ink tube 10,000,000 paths 5,800,000 paths 10,000,000 paths 5,800,000 paths

Epson Stylus Pro

9900/9910

Until any one of the following conditions is met.

 5 years  Carriage life:

5,000,000 paths

 Approx. 16,000 pages

(Super B0 size/Plain paper, Quality mode/ 720x720 dpi)

 Standard paper: approx. 20,000 cuts or more  Hard cut paper: approx. 5,000 cuts or more

5 years or longer

Approx. 20,000 pages (reference value) (Super B0 size /EPSON paper/Quality mode/ Continuous printing/720x720 dpi)

Approx. 5,000,000 paths Approx. 2,900,000 paths Approx. 5,000,000 paths

Epson Stylus Pro

9700/9710

Until any one of the following conditions is met.

 5 years  Carriage life:

5,000,000 paths

 Approx. 40,000 pages

(Super B0 size/Plain paper, Quality mode/ 720x720 dpi)

Epson Stylus Pro

7900/7910

Until any one of the following conditions is met.

 5 years  Carriage life:

2,900,000 paths

 Approx. 16,000 pages

(Super A1 size/Plain paper/Quality mode/ 720x720 dpi)

Approx. 20,000 pages (reference value) (Super A1 size /EPSON paper/Quality mode/ Continuous printing/720x720 dpi)

Epson Stylus Pro 7700/7710/

7700M/

7710M

Until any one of the following conditions is met.

 5 years  Carriage life:

2,900,000 paths

 Approx. 40,000 pages

(Super A1 size/Plain paper/Quality mode/ 720x720 dpi)

Epson Stylus Pro

WT7900/WT7910

Until any one of the following conditions is met.

 5 years  Carriage life:

2,900,000 paths

 Approx. 7,700 pages

(A2 size/ClearProof Film/720x1440 dpi)

 Approx. 10,000

pages (A2 size/EPSON paper/720x720 dpi)

 Standard paper:

approx. 20,000 cuts or more

 Hard cut paper:

approx. 5,000 cuts or more

 ClearProof Film:

approx. 10,000 cuts or more

Approx. 20,000 pages (Super A1 size/EPSON paper/Continuous printing/720x720 dpi)

Epson Stylus Pro

9890/9908

Until any one of the following conditions is met.

 5 years  Carriage life:

5,000,000 paths

 Approx. 20,000

pages (Super B0 size/Plain paper, Quick mode/ 360x720 dpi)

 Standard paper: approx. 20,000 cuts or more  Hard cut paper: approx. 5,000 cuts or more

Approx. 20,000 pages (reference value) (Super B0 size /EPSON paper/Quality mode/ Continuous printing/720x720 dpi)

Epson Stylus Pro

7890/7908

Until any one of the following conditions is met.

 5 years  Carriage life:

2,900,000 paths

 Approx. 20,000

pages (Super A1 size/Plain paper, Quick mode/ 360x720 dpi)

Note *: These values are provided only as a guide. Service call is not indicated for these parts.

PRODUCT DESCRIPTION Basic Specifications 24

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

 SpectroProofer

Item Specified values

Until any one of the following conditions is met.

Mounter

 5 years  200,000 paths for color measurement

PRODUCT DESCRIPTION Basic Specifications 25

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.2.6 Auto Take-up Reel Unit

Item Specified values

Paper Width 406 to 1,118 mm

Paper length

Rotation speed Max. 40 rpm

Weight 6.9 kg

Environment

Rated voltage AC 100 to 240 V

Input voltage range AV 90 to 264 V

Rated frequency range 50 to 60 Hz

Input frequency range 49.5 to 60.5 Hz

Rated current 0.2 A

Power consumption

2-inch core: 1.3 to 40 m

3-inch core: 1.6 to 30.5 m

Temperature: 10 to 35 °C

Humidity: 20 to 80%

Approx. 9 W

Approx. 3 W in Ready Mode

PRODUCT DESCRIPTION Basic Specifications 26

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.3 Printing Specifications

1.3.1 Paper Feed Specifications

Item Specification

Paper feed method Friction feed

Return pitch 2.2049

Paper feeder

Feed speed 300 ms/ (1/6 inch)

μm (1/11,520 inch)

 Roll paper manual feed  Cut sheet manual feed

1.3.2 Paper Specification

1.3.2.1 Supported Paper

The following explains the supported paper sizes and thickness.

C A U T I O N

ROLL PAPER

Paper type Plain paper, recycled paper, others

Roll paper size

Paper size W x L (within roll paper size)

Paper thickness

Available width for borderless printing

Note : Borderless printing is not available for Epson Stylus Pro WT7900/WT7910.

 Do not use wrinkled, scuffed, torn, or soiled paper.  Load paper just before printing. Do not leave paper loaded on

the printer when not printing. Store paper properly following the instruction that comes with the paper.

 When large quantities of paper need to be prepared in advance,

make a test print using the paper before purchase.

Item Specification

2-inch core: Outer diameter 103 mm or less x 1 roll

3-inch core: Outer diameter 150 mm or less x 1 roll

 Epson Stylus Pro 9700/9710/9900/9910/9890/9908:

2-inch core: 254 to 1118 mm x 45 m 3-inch core: 254 to 1118 mm x 202 m

 Epson Stylus Pro 7700/7700M/7710/7900/7910/

WT7900/WT7910/7890/7908: 2-inch core: 254 to 610 mm x 45 m

3-inch core: 254 to 610 mm x 202 m

Plain paper, recycled paper:

0.08 to 0.11 mm (Weight: 64 to 90 g/m2)

Others: 0.08 to 0.50 mm

10 inches, 300 mm, 13 inches (Super A3), 16 inches, 17 inches, 515 mm (B2), 594 mm (A1), 24 inches (Super A1), 728 mm (B1), 36 inches (Super A0), 44 inches (Super B0)

PRODUCT DESCRIPTION Printing Specifications 27

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

CUT SHEET

Item Specification

Paper type Plain paper, recycled paper, others

 Epson Stylus Pro 9700/9710/9900/9910/9890/9908:

Width: 210 to 1118 mm Length: 279.4 to 1580 mm (A4 to Super B0)

Paper type

Paper thickness

Available width for borderless

printing

Note *1 : Borderless printing is not available for Epson Stylus Pro WT7900/WT7910.

*2: Not supported for Epson Stylus Pro 7890/7908.

 Epson Stylus Pro 7700/7700M/7710/7900/7910/

WT7900/WT7910/7890/7908: Width: 210 to 610 mm

Length: 279.4 to 914 mm (A4 to Super A1)

Plain paper, recycled paper: 0.08 to 0.11 mm

(Weight: 64 to 90 g/m2)

Others

 Epson Stylus Pro 7700/7710/7700M/7710M/7900/

7910/9700/9710/9900/9910/WT7900/WT7910

 Length 279 to 728 mm: 0.08 to 1.50 mm

 Length over 728 to 2032 mm: 0.08 to 0.50 mm

 Epson Stylus Pro 9890/9908

 Length 279 to 762 mm: 0.08 to 1.50 mm

 Length over 762 to 1580 mm: 0.08 to 0.50 mm

 Epson Stylus Pro 7890/7908

 Length 279 to 762 mm: 0.08 to 1.50 mm

 Length over 762 to 914 mm: 0.08 to 0.50 mm

10 inches, 300 mm, 13 inches (Super A3), 16 inches, 17 inches, 515 mm (B2), 594 mm (A1),

24 inches (Super A1), 728 mm (B1) 36 inches (Super A0)*2, 44 inches (Super B0)

PRODUCT DESCRIPTION Printing Specifications 28

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

1.3.2.2 Designated Paper

ROLL PAPER

Note *1 : OK!: Recommended for borderless printing

OK: Borderless printing is available NA: Borderless printing is NOT available Borderless printing on the borderless printing available paper (OK) may result in drop in print quality or fail to produce complete borderless (white margins may appear) due to expanding of the paper. Borderless printing can be made on commercially available paper, however, note that the availability is restricted by the paper size.

*2: Not supported for Epson Stylus Pro 7700/7710/7900/7910/WT7900/WT7910/7890/7908.

*3: Auto Take-up Reel Unit is used. (only Pro 9700/9710/9900/9910/9890/9908)

*4: When using the tensioner included in the Auto Take-up Reel Unit of Pro 9700/9710/9900/9910.

Table 1-5. Designated Roll Paper List

Size

Take-up*

Applied model

Name

Premium Glossy Photo Paper (250)

Premium Semigloss Photo Paper (250)

406mm 16"

610mm 24"

914mm*

1118mm*344"*

406mm 16"

610mm 24"

914mm*

1118mm*244"*

inch

36"*

Borderless

Thickness

OK! 0.27mm 3" Standard

Core

Diameter

Roll

Paper

Tension

Upper: Pro7900/7910/9900/9910/9890/

ICC Profile

9908/7890/7908

Lower:Pro7700/7710/7700M/7710M/

9700/9710

 Photo Black: Pro9900_7900

PremiumGlossyPhotoPaper250.icc

 Matte Black: ---

 Photo Black: Epson Stylus Pro

7700_7710_9700_9710 PremiumGlossyPhotoPaper250.icc

 Matte Black: ---

 Photo Black: Pro9900_7900

PremiumGlossyPhotoPaper250.icc

 Matte Black: ---

 Photo Black: Epson Stylus Pro

7700_7710_9700_9710 PremiumGlossyPhotoPaper250.icc

 Matte Black: ---

Driver Setting

Photo Paper

Premium

Glossy

Photo Paper

(250)

Premium

Semigloss

Photo Paper

(250)

Auto

Black

Cut

Forward Backward

Ink

9890/9908/7890/7908

Pro7900/7910/9900/9910/

  OK PK   

  OK PK  

ProWT7900/WT7910

Pro7700/7710/7700M/7710M/9700/9710

PRODUCT DESCRIPTION Printing Specifications 29

Confidential

Epson Stylus Pro 7700/7710/7700M/7710M/7900/7910/9700/9710/9900/9910/WT7900/WT7910/9890/9908/7890/7908 Revision I

Table 1-5. Designated Roll Paper List

Size

Take-up*

Applied model

Name

Premium Luster Photo Paper (260)

Premium Semimatte Photo Paper (260)

Photo Paper Gloss 250

Borderless

inch

254mm 10"

300mm 12"

406mm 16"

508mm 20" NA

610mm 24"

36"*

1118mm*244"*

406mm 16"

610mm 24"

914mm*

1118mm*244"*

36"*

432mm 17"

610mm 24"

914mm*

1118mm*244"*

36"*

Roll

Paper

Tension

Thickness

Core

Diameter

OK!

0.27mm 3" Standard

OK!914mm*

OK! 0.27mm 3" Standard

OK! 0.25mm 3" Normal

Upper: Pro7900/7910/9900/9910/9890/

ICC Profile

9908/7890/7908

Lower:Pro7700/7710/7700M/7710M/

9700/9710

 Photo Black: Pro9900_7900

PremiumLusterPhotoPaper260.icc

 Matte Black: ---

 Photo Black: Epson Stylus Pro

7700_7710_9700_9710 PremiumLusterPhotoPaper260.icc

 Matte Black: ---

 Photo Black: Pro9900_7900

PremiumSemimattePhotoPaper260.i cc

 Matte Black: ---

 Photo Black: Epson Stylus Pro

7700_7710_9700_9710 PremiumSemimattePhotoPaper260.i cc

 Matte Black: ---

 Photo Black: Pro9900_7900

PhotoPaperGloss250.icc

 Matte Black: ---

 Photo Black:Epson Stylus Pro

7700_7710_9700_9710PhotoPaper Gloss

250.icc

 Matte Black: ---

Driver Setting

Photo Paper

Premium

Luster Photo

Paper (260)

Premium

Semimatte

Photo Paper

(260)

Photo Paper

Gloss 250

Auto

Black

Cut

Forward Backward

Ink

Pro7900/7910/9900/9910/

NA NA

OK PK  

 

  OK PK  

9890/9908/7890/7908

ProWT7900/WT7910

Pro7700/7710/7700M/7710M/9700/9710

PRODUCT DESCRIPTION Printing Specifications 30

Confidential

+ 489 hidden pages