Page 1
LINN Series
USER MANUAL
Page 2
Contents
1) Introduction p3
2) Product overview p4
Top Flat in RGB, MONO & RGBW PIXEL p4
Side Flat in RGB, MONO & RGBW PIXEL p5
Side Round in RGB, MONO & RGBW PIXEL p5
3) Mounting product p8
Top Flat and LINN Top Flat Mini p8
LINN Side Flat and LINN Side Round p9
4) Electrical connections p11
9) Contact Details p12
User Manual version 1 | page 2
epslighting.com | Specication subject to change without notice
Page 3
1. Introduction
EPS Lighting is based in the United Kingdom, in the County of Essex. If you add our
expert team of designers and product development engineers together, we have
an extensive number of years’ experience in the design and specication of lighting
products and projects. We know exactly what we are looking to achieve when it
comes to developing cutting edge, robust and future proofed lighting products and
associated controls. Whether you need lighting for a residential or commercial project,
we have solutions for all applications including the home, industry, road, façade and
creative lighting markets.
EPS Lighting is a sister company to Elumeros which caters for high-end exterior
illumination systems, covering ood, grazing, wash, spot and media facade solutions.
You can visit Elumeros’ website by visiting www.elumeros.com
LINN Series
Are you looking for a durable LED
product to highlight the architectural
details of a façade or create dramatic
visual effects? With the ability to
withstand the elements?
Then meet Linn, our IP68, IK08,
specication grade, exible LED light
line. PVC injection moulded, the Linn
series offers design exibility with bend
diameters ranging from 8-12cm. Side or
Top light emission? The range is built to
order, therefore light emission surface,
specic lengths, beam angles and
power feed options are manufactured
to meet and full the requirements of
your project, ensuring the best possible
installation results. Furthermore, Linn has
a dot free, homogeneous light across the
emission surface.
LINN Top Flat LINN Top Flat Mini
LINN Side Flat
User Manual version 1 | page 3
epslighting.com | Specication subject to change without notice
LINN Side Round
Page 4
2. Product Overview
Flexible, durable, creative
Are you looking for a durable LED product to highlight the architectural details of a
façade or create dramatic visual effects? With the ability to withstand the elements?
Then meet Linn, our IP68, IK08, specication grade, exible LED light line.
PVC injection moulded, the Linn series offers design exibility with bend diameters
ranging from 8-12cm. Side or Top light emission? The range is built to order, therefore
light emission surface, specic lengths, beam angles and power feed options are
manufactured to meet and full the requirements of your project, ensuring the best
possible installation results. Furthermore, Linn has a dot free, homogeneous light
across the emission surface.
S
S
S
CLASS III IP68
CLASS 3
ELECTRICAL
INGRESS
RATING
IK08
IMPACT
RATING
R
UV
PROTECTED
S
CORROSION
RESISTANT
DIRT
RESISTANT
SALTWATER
RESISTANT
B
ONE BIN
ONLY
To help with specication, we offer a
dedicated design and support service to
all our customers.
Please speak to your local representative
or distributor for more information.
LINN - Top Flat in RGB, MONO & RGBW PIXEL
Bending lines of light in white or colour, with light emissions
from the top
- Emission surface along the top
- Flat rectangular emission surface with 115-degree beam angle
- 12cm bend diameter
- Available in static colours including white in CCT ranging from 2200 - 6500K
(please refer to our online data sheets for the exact colour range)
- Colour options include RGB, RGBW, DW and Pixel
- DMX/RDM, DALI and 0-10V control options
- Mini version also available in mono only
BEAM
ANGLE
115°
CONTROLS
DMX/RDM
POWER
10W/m
MIN.
BENDING
DIA
12cm
COLOUR
TEMP
2200k
- 6500k
(WHITE)
MIN.
LENGTH
8.3cm
LUMEN
450
lm/m
(6500k
WHITE)
MAX.
LENGTH
10m
420
lm/m
(2200k
WHITE)
ONE BIN
ONLY
B
COLOUR
RENDER
CRI>80
(WHITE)
RGB N/A
COLOUR
OPTIONS
RGB
RGBW
DW PIXEL
17mm
Bending
direction
16mm
User Manual version 1 | page 4
epslighting.com | Specication subject to change without notice
Page 5
LINN - Side Flat in RGB, MONO & RGBW PIXEL
Bending lines of light in white or colour, with light
emission from the side
- Flat rectangular emission surface with 118-degree beam angle
- 8/12cm bend diameter, dependant on variant
- Available in static colours including white in CCT ranging from 2200 - 6500K
(please refer to our online data sheets for the exact colour range)
- Colour options include RGB, RGBW, DW and Pixel
- DMX/RDM, DALI and 0-10V control options
BEAM
ANGLE
118°
CONTROLS
DMX/RDM
POWER
15W/m
MIN.
BENDING
DIA 8cm
(MONO)
DIA 12cm
(RGB)
COLOUR
TEMP
2200k -
6500k
MIN.
LENGTH
8.3cm
LUMEN
380
lm/m
(6500k
WHITE)
MAX.
LENGTH
10m
340
lm/m
(2200k
WHITE)
ONE BIN
ONLY
B
COLOUR
RENDER
CRI>80
(WHITE)
RGB N/A
COLOUR
OPTIONS
RGB
RGBW
DW PIXEL
LINN - Side Round in RGB, MONO & RGBW PIXEL
Visually dramatic effects with a wider beam angle and curved
light emission surface
- Emission surface to the side
- Rounded emission surface with 270-degree beam angle
- 8/12cm bend diameter, dependant on variant
- Available in static colours including white in CCT ranging from 2200 - 6500K
(please refer to our online data sheets for the exact colour range)
- Colour options include RGB, RGBW, DW and Pixel
- DMX/RDM, DALI and 0-10V control options
BEAM
ANGLE
270°
CONTROLS
DMX/RDM
POWER
15W/m
MIN.
BENDING
DIA 8cm
(MONO)
DIA 12cm
(RGB)
COLOUR
TEMP
2200k -
6500k
MIN.
LENGTH
8.3cm
LUMEN
PLEASE
CONACT
US
MAX.
LENGTH
10m
COLOUR
RENDER
CRI>80
(WHITE)
RGB N/A
ONE BIN
ONLY
COLOUR
OPTIONS
RGB
B
RGBW
DW PIXEL
11.5mm
15.5mm
11.5mm
Bending
direction
21mm
27mm
User Manual version 1 | page 5
epslighting.com | Specication subject to change without notice
Page 6
2. Product Overview
This product left the place of manufacture in perfect condition.
In order to maintain this condition and for safe operation, the user must always follow
the instructions and safety warnings described in this user manual.
Safety Warning!
General
- This product must be installed by a qualied and competent professional.
- When working on the xture, heat resistant gloves should be worn to provide
adequate user protection.
- Do not work on the product with wet hands.
- Always disconnect the power supply before attempting to maintain or service
the equipment.
- Always operate the equipment as described in this user manual.
- Do not stand close to the equipment and stare directly into the LED light source.
- Make sure that all parts of the equipment are kept clean and free of dust which
should be carried out as part of a maintenance cycle that’s appropriate for the
installation location of the product.
- When transferring the product, it is advisable to use the original packaging in
which the product left the factory.
- Shields, lenses, ultraviolet screens and pressure release valves should be
changed if they have become damaged to such an extent that their
effectiveness is impaired.
- The lamp (LED) should be changed if it has become damaged or thermally
deformed.
- The power supply (PSU), DMX/RDM driver and LED drivers should be changed if
they fail to operate.
Installation
- A minimum distance of 0.5m must be maintained between the equipment and
any combustible surface. The mounting surface must not be combustible.
- Always ensure the supporting structure is a at and solid surface and can support
the weight of the product and any additional wind or shear force. The supporting
structure must be capable for the installation of luminaires, and advice must be
taken from an appropriately qualied and competent person to verify proposed
mounting positions and surfaces.
- Always make sure that the equipment is installed securely and ensure all safety
anchors are installed.
- The product must be installed within well-ventilated areas.
- The Earth wire MUST ALWAYS be connected.
- Local electrical and building regulations must be followed. If in doubt, please
contact Elumeros support.
- Avoid shaking or strong impacts to any part of the equipment.
- Always make sure that the power and data connections are connected correctly
and securely. If there is any malfunction of the equipment, contact EPS Lighting or
your local distributor immediately.
- This xture should not be buried.
This user manual is intended to cover as
much detail as possible for this product,
and great care has been taken to ensure
this and the accuracy of the information
contained within, however should
additional information or clarication be
required that is not covered within this
manual or associated data sheets, or if
there are any uncertainties regarding the
installation and operation of this product,
EPS Lighting MUST be contacted before
any work is carried out on the xture or
associated products.
FAILURE TO COMPLY WITH THIS
MANUAL AND LOCAL ELECTRICAL
AND CONSTRUCTION REGULATIONS
MAY RESULT IN SERIOUS INJURY
OR EVEN DEATH - ALWAYS ISOLATE
POWER BEFORE WORKING ON
ELECTRICAL PRODUCTS AND ENSURE
ADEQUATE MEASURES ARE TAKEN TO
MECHANICALLY SUPPORT FIXTURES AT
ALL TIMES.
Caution, risk of electric shock
The light source and other
electronic components
contained in this luminaire
shall only be replaced by
EPS Lighting or an approved
service agent.
Technical Support
EPS Lighting Ltd
25A, Little Boyton Hall Farm,
Boyton Cross, Chelmsford,
Essex CM1 4LN, UK
T +44 (0) 330 223 2348
F +44 (0) 330 223 2995
contact@epslighting.com
User Manual version 1 | page 6
epslighting.com | Specication subject to change without notice
Page 7
LINN Specic Installation
- Although this product does not generate a great amount of heat, it is
recommended that you do not cover or conceal it.
- Do not route the product through walls, doors, windows, or building structures.
- Do not roll out the product onto rough surfaces or over sharp corners. This will
scratch the PVC optics and damage the nish of the product.
- Do not use the product if:
The outer PVC jacket is damaged
There are loose electrical connections
The wires are visible without insulation.
- Do not secure the product with staples, nails, or alike that might damage the
insulation or PVC material.
- Do not install the product on/in places where it is subject to continuous exing.
- Do not operate/run the product in temperatures exceeding 45C or 113F.
- Do not operate the product over the specied voltage or LED life degradation
will be greatly increased.
- Do not leave any part of the product unsecured.
- Constant movement over time from weather can cause damage.
- Do not reverse polarity when connecting from both ends. This will damage the
internal PCB. Always test connections with a multi-meter before applying power.
- Do not energise the product whilst in packaging.
- The product can be cut only where marked. Look for the “Dotted Line” or
“Scissor Mark”. A cut section must have the appropriate LINN IP rated cap
accessory to maintain IP ratings.
- Cutting outside of the specied mark will damage the light.
- Do not cut while the LED ex neon is connected to power.
- Do not install in human inhabited pools.
- Must always be used with an electrical isolation transformer providing SELV
(safety extra low voltage).
This user manual is intended to cover as
much detail as possible for this product,
and great care has been taken to ensure
this and the accuracy of the information
contained within, however should
additional information or clarication be
required that is not covered within this
manual or associated data sheets, or if
there are any uncertainties regarding the
installation and operation of this product,
EPS Lighting MUST be contacted before
any work is carried out on the xture or
associated products.
FAILURE TO COMPLY WITH THIS
MANUAL AND LOCAL ELECTRICAL
AND CONSTRUCTION REGULATIONS
MAY RESULT IN SERIOUS INJURY
OR EVEN DEATH - ALWAYS ISOLATE
POWER BEFORE WORKING ON
ELECTRICAL PRODUCTS AND ENSURE
ADEQUATE MEASURES ARE TAKEN TO
MECHANICALLY SUPPORT FIXTURES AT
ALL TIMES.
Caution, risk of electric shock
The light source and other
electronic components
contained in this luminaire
shall only be replaced by
EPS Lighting or an approved
service agent.
Technical Support
EPS Lighting Ltd
25A, Little Boyton Hall Farm,
Boyton Cross, Chelmsford,
Essex CM1 4LN, UK
T +44 (0) 330 223 2348
F +44 (0) 330 223 2995
contact@epslighting.com
User Manual version 1 | page 7
epslighting.com | Specication subject to change without notice
Page 8
3. Mounting Product
LINN is a highly durable product but must be installed in accordance to the pictures
shown below, which indicate the minimum bending parameters as well as the correctly
bending direction for each specic variant of LINN.
LINN Top Flat and LINN Top Flat Mini
LINN must be installed by at least 2 people, who can support the product in various
locations as shown. During installation, care should be taken to ensure the bending
radius of LINN is not exceeded.
Light prole
16.5mm
16.5mm
Light direction
Bend
vertically
only
LINN Top Flat LINN Top Flat
Light prole
13.5mm
13.5mm
Light direction
Bend
vertically
only
LINN Top Flat Mini LINN Top Flat Mini
Minimum bending direction
Light
emitting
surface
Minimum bending direction
Light
emitting
surface
Ø120mm
Ø120mm
Ø60mm
Ø60mm
Light
emitting
surface
Light
emitting
surface
User Manual version 1 | page 8
epslighting.com | Specication subject to change without notice
Page 9
LINN is a highly durable product but must be installed in accordance to the pictures
shown below, which indicate the minimum bending parameters as well as the correctly
bending direction for each specic variant of LINN.
LINN Side Flat and LINN Side Round
LINN must be installed by at least 2 people, who can support the product in various
locations as shown. During installation, care should be taken to ensure the bending
radius of LINN is not exceeded.
Light prole
21mm
11.5mm
Light direction
Bend
horizontally
only
LINN Side Flat LINN Side Flat
29mm
11.5mm
Light direction
Minimum bending direction
Minimum bending directionLight prole
Light
emitting
surface
Ø120mm
Ø120mm
Light
emitting
surface
Light
emitting
surface
Light
emitting
surface
General Do NOTS
The images give indication as to what
is not acceptable as an intended
installation or during installation of
other xing methods.
User Manual version 1 | page 9
epslighting.com | Specication subject to change without notice
Bend
horizontally
only
LINN Side Round LINN Side Round
x
x
x
Page 10
3. Mounting Product
Cutting Guide
LINN is a specication grade product, and all power feeds and end caps are factory
moulded. There are occasions where LINN may need to be cut, and this can be done
by taking note of the minimum cutting distances which differ between versions.
Reference should be made to this guide, data sheets and the indicated scissor/cut
marks on the product itself. The cut lengths must then be tted with an appropriate IP
rated end cap (available separately from the LINN catalogue).
For guidance when installing the end cap, please contact technical support.
Note that when cutting LINN Pixel products, the number of LED nodes and control
addresses will reduce which may impact an SPI/DMX signal patch. Care should be
taken to ensure cut lengths are catered for in control programming interfaces and
address allocations.
General Mounting
LINN can be fastened to surfaces using appropriate accessories available from EPS
Lighting. Please refer to data sheets or contact technical support for a copy. The
use of glues and resins as xing agents should be avoided. Use of glues and resins
may invalidate the warranty of the product, unless it’s use is agreed in writing by EPS
Lighting as part of a detailed project specication.
The images indicate one type of xing available in the accessories range. The different
xings serve obvious purposes, however when in doubt technical support should be
contacted.
Quantities of accessories and xings are dependent on the type and its effect on the
variant LINN it’s being used with. Care should be taken to ensure drooping is avoided,
and to ensure that LINN is fastened adequately to avoid stresses on LINN itself.
PCB
PVC
Screw
LED
Aluminium
prole
Installation
surface
Light surface
Cutting line
Power Feed Options
LINN comes with a choice either bottom, side and end moulded power feeds which
can be used for various installation methods to ensure hidden cables and a seamless
lines of light. The type of feed can be found on order forms, catalogues and data
sheets.
User Manual version 1 | page 10
epslighting.com | Specication subject to change without notice
Page 11
4. Electrical Connections
LINN is manufactured to order, meaning that the appropriate power feeds are factory
moulded. There are two options available for all versions, these are bare end cables
or plugs.
Bare end cables come with a standard length which can vary pending the
manufacturing process, therefore it is recommended to ensure the feeder cable is
long enough to reach the cable entry point of LINN, where connections can be made.
Plugs are designed for “plug-and-play” type installations, whereas the installer would
ensure female sockets are available at each LINN start location, with the male type
LINN connector then plugging into this female type socket. Female sockets are
available as separate items.
Note that custom feed cable lengths are available upon special request.
LINN is a high-powered product, which requires a detailed electrical design to ensure
equal balancing of loads across drivers and power supplies. Reference can be made
to the various data sheets for specic variants, that indicate the operating voltage and
the wattage per metre. Technical support is on hand to assist with control and power
design. LINN operates at 24Vdc unless otherwise stated in specic data sheets or
product labels. Care should be taken to ensure the operating voltage is constant
(constant voltage). A maximum volt drop of 5% is allowed (for example at 24Vdc, the
maximum voltage drop would be 1.2V meaning a delivered voltage of 22.8V to the
xture.
EPS Lighting has an extensive range of power supplies, LED Drivers, SPI pixel
gateways and various DC-DC transformers which allow installers to overcome volt
drop issues, as well as various control options such as stand-alone DMX interfaces to
multi-universe video matrix type products. EPS Lighting also has an in-house design
and engineering team that can deliver such systems, please contact support for more
information.
Below is a guide which indicates the number of cores and the connections they relate
to. Each manufactured length of LINN will have a factory tted label which indicates
the correct cores to use, as well as the colour of each specic core and its associated
connection. The below guide is in black and white for clarity, and reference should
always be made to the label on the product itself as sometimes, the cable colours may
vary pending manufacturing processes or for custom orders. If in doubt, or if the label
is missing, contact support for assistance before connecting to power.
End (bare end cable and plug)
Side (bare end cable and plug)
Bottom (bare end cable and plug)
Monochromatic RGB RGBW
+24Vdc
Common 0Vdc
Dynamic White Pixel SPI
Warm white
+24Vdc
Cool White
+24Vdc
Common 0Vdc
User Manual version 1 | page 11
epslighting.com | Specication subject to change without notice
Red +24Vdc
Green +24Vdc
Blue +24Vdc
Common 0Vdc
+24Vdc
Data
Common 0Vdc
Red +24Vdc
Green +24Vdc
Blue +24Vdc
White +24Vdc
Common 0Vdc
Page 12
EPS Lighting Ltd
25A Little Boyton Farm
Boyton Cross
Chelmsford
Essex CM1 4LN UK
t: +44 (0) 330 223 2348
f: +44 (0) 330 223 2995
e: contact@epslighting.com
www.epslighting.com
Please note:
Lumen performance and colour
temperature typical values and due to
production processes and the nature
of LEDs and electronics, values for
output and electrical characteristics can
vary by up to 10% with small variables
also possible for sizes, weights and
dimensions.
Loading...