Page 1
MVP4G
ISA/PCI Motherboard with Onboard AGP
VGA PCI Audio, PCI IDE and Super
Multi-I/O
TRADEMARK
All products and company names are trademarks or registered
trademarks of their respective holders.
These specifications are subject to change without notice.
Manual Revision 6.0
September 17, 1999
Page 2
MVP4G Features:
FeaturesMVP4G
FEATURES
•Intel Pentium
K5/K6, Cyrix 6x86L/6x86MX & idt C6 operating at 133 ~ 450 MHz with
321 ZIF socket 7 provides scalability to accept faster Processors in the
future.
®
Processor, Pentium Processor with MMX technology, AMD
•Designed with VIA MVP4 AGPset.
•Supports up to 768 Mega of DRAM (minimum of 16 MB) on board, You can
use 168-pin DIMM x 3. It will automatically detect Extended Data Output
(EDO) DRAM at 66MHz only or Synchronous DRAM memory (SDRAM) at
66MHz or 100MHz
•Supports (1) 16 bit ISA slots, (4) 32 bit PCI slots, (1)AMR and provides
(2) independent high performance PCI IDE interfaces capable of supporting PIO
Mode 3/4 and Ultra DMA 33/66 devices. The MVP4G supports (2) PCI
Bus Master slots and a jumperless PCI INT# control scheme which reduces
configuration confusion when plugging in PCI card(s).
•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary IDE
interfaces.
•Designed with lntegrated Multi I/O: (1) floppy port, (1) parallel port (EPP,
ECP), and (2) serial ports (16550 Fast UART).
Note: Japanese “Floppy 3 mode” is also supported
•Features Award Plug & Play BIOS. With Flash Memory you can always
upgrade to the current BIOS as they are released.
•MVP4G utilizes a Lithium battery which provides environmental protection
and longer battery life.
• Software power-down when using Windows
®
95/98.
• Supports ring-in feature (remote power-on through external modem,
allows system to be turned on remotely).
Page 2
Page 3
FeaturesMVP4G
•Resume by Alarm - Allows your system to turn on at a preselected time.
•Supports CPU Hardware sleep and SMM (System Management Mode).
•Supports Keyboard power ON function (KBPO).
•Supports USDM software to offer motherboard various status.
•Supports the CPU and Chassis fan Auto stop in sleep mode.
•Built-in WOL (Wake On LAN) Connector.
• Built-in Sound Blaster/DirectSound AC97 Audio.
• Built-in AGP 2D/3D Graphics Accelerator.
Page 3
Page 4
InstallationMVP4G
MVP4G Detailed Layout
PS/2
USB
J4
CPU FAN
Bank 2
Bank 1
Bank 0
ON
USB 1
(Top)
USB 0
(Bottom)
Mouse
(Top)
Keyboard
(Bottom)
1
JP4
SOCKET 7
COM 1
Parallel Port
VGA
J6
VIA
VT8501
DIMM 3
DIMM 2
DIMM 1
Chassis FAN
Game Port
Secondary IDE
CD1
AUX1
AMR
USB CONN.
COM2
PCI Slot #1
PCI Slot #2
PCI Slot #3
J7:WOL
PCI Slot #4
VIA
VT82C686 A
JP1
1
FDD1
Flash Memory
Battery
for BIOS
IDE1
JP3
IDE2
J3
POWER_ON/OFF
5
IR CONN.
1
5
Power LED
1
SPK
RESET
J2
Page 4
ISA Slot #1
Figure 1
Page 5
InstallationMVP4G
Easy Installation Procedure
The following must be completed before powering on your new system:
Configure Jumpers to match your hardware
Install memory chips
Device Connectors
Configure Jumpers
We design this motherboard with the fewest jumpers to make your install fast and
easy.
The following will describe all of the jumpers that you are required to set before
moving on to step 2.
Note: The jumpers as depicted as shown (Figure 1) in their correct physical orientation.
JP1 CMO S C lear
1
JP1 = 1-2 - Ru n Mode (Default)
3
1
JP4Keyboard Power-ON function (refer to the section 3-4)
JP4=1-2 -
3
J7WOL (Wake On
= 2-3 - C lear C M O S (momentarily)
Disabled(Default)
=2-3 -
Enabled
LAN)
Connector
Reserved for NIC (Network Interface C ard) to
Wake the System .
Page 5
Page 6
InstallationMVP4G
SW1: CPU Vcore Selection
SW 1 CPU
ON
2
1
34
JP3: CPU Speed Selection
1
5
2
ON
ON
3
ON
4
ON
ON
ON
ON
ONON
ON
ON
ONON
ON
ON
5
ON
ON
Vcore
1.8V
2.0V
2.1V
2.2V
2.3V
2.4V
2.8V
2.9V
3.2V
XMM/muitneP
6K/5KDMA
6C-TDI
zHM661
zHM052zHM001663RP
ZHM002
zHM052zHM38333RP
zHM003zHM001334RP*
zHM332
zHM333zHM59664RP*
zHM053zHM001005RP*
zHM662
zHM333zHM38664RP*
zHM083zHM59335RP*
zHM004zHM001055RP*
zHM003
zHM054zHM001
zHM333
zHM574zHM59
zHM005zHM001
zHM663X5.5zHM66
X3
X4
X5
3PJ
reilpitluMkcolCsuB
zHM66002RP
zHM57332RP
X5.2
X5.3
X5.4
zHM38662RP
zHM59003RP
zHM66662RP
zHM57003RP
zHM59004RP*
zHM66003RP
zHM57333RP
zHM38004RP*
zHM66333RP
zHM57004RP
zHM66
zHM66
MBI/xiryC
IIM/XM68x6
* Reserved
Page 6
Page 7
InstallationMVP4G
System Memory Configuration
Memory Layout
The MVP4G supports (3) 168-pin DIMMs (Dual In-line Memory Module). The
DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized
DRAM). The DIMMs may be installed using just one chip.
• We recommend using SDRAM DIMM can not mixing
with EDO DIMM modules.
• DIMM SDRAM may be 83MHz (-12ns), 100MHz (-10ns) or
125MHz (-8ns) bus speed.
• No Registered DIMM support.
Figure 2 and T able 1 show several possible memory configurations using
DIMM 1
DIMM 2
DIMM 3
yromeMlatoT
BM821=
mumixaM
BM652=
mumixaM
BM483=
mumixaM
1MMID
)0knaB(
*MARDS/ODE
,BM23,BM61,BM8
1XBM821,BM46
*MARDS/ODE
,BM23,BM61,BM8
1XBM821,BM46
*MARDS/ODE
,BM23,BM61,BM8
1XBM821,BM46
Bank 0
Bank 1
Bank 2
2MMID
)1knaB(
enoNenoN
*MARDS/ODE
,BM23,BM61,BM8
1XBM821,BM46
*MARDS/ODE
,BM23,BM61,BM8
1XBM821,BM46
* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.
Table 1
-Synchronous
-EDO
3MMID
)2knaB(
enoN
*MARDS/ODE
,BM23,BM61,BM8
1XBM821,BM46
Page 7
Page 8
InstallationMVP4G
Device Connectors
Please install the motherboard into the chassis.
Now that your motherboard is installed you are ready to connect all your connections
(figure 6).
parallel port
Joystick/Midi port
PS/2 Mouse
PS/2
KEYBOARD
USB port
COM1 VGA1
Figure 6
J4:CPU Fan Power
• A plug-in for the CPU Fan Power
J6:Chassis Fan Power
• A plug-in for the chassis Fan Power
J7:WOL (Wake On LAN) Connector
PW1:ATX Power Connector
• 20-pin power connector
J2,J3:Chassis Panel Connector
• Power_LED, Speaker, Reset, Sleep, Turbo LED and HDD LED
IDE1:Primary IDE Connector
IDE2:Secondary IDE Connector
FDD1:Floppy Controller Connector
CD1:MITSUMI CD-ROM Audio_in
AUX1:Extra CD Audio Connector
COM2: RS232 COM2
Connector
USB CONN.: The third and fourth USB port (cable optional)
Speaker
Line_in
MIC
Page 8
Page 9
Device Connectors (continued)
InstallationMVP4G
J2
J3 1
+
+
Reset - Closed to restart system.
1
Speaker - Connect to the system's speaker for beeping
1. Speaker 3. GND
2. N/C 4. GND
Power LED connector
1
1. Power LED(+) 4. NC
2. N/C 5. GND
5
5
3. GND
IR Connector
1. VCC 4. GND
2. NC 5. IRTX
3. IRRX
IDE LED indicator - LED ON when Onboard PCI IDE Hard disks is
activate
Turbo LED indicator - LED ON when higher speed is selected
Power On/Off - This is connected to the power button on the case.
Using the Soft-Off by Pwr-BTTN feature, you can choose either
Instant Off (turns system off
hold the button down for 4 seconds before the system turns off). When
the system is in 4 sec delay mode, we has added a special feature to
make the system go into suspend mode when the button is pressed
momentarily.
immediately), or 4 sec delay (you need to
Page 9
Loading...