Page 1
MVP4F
ISA/PCI Motherboard with Onboard AGP
VGA, PCI Audio, PCI IDE and Super
Multi-I/O
TRADEMARK
All products and company names are trademarks or
registered trademarks of their respective holders.
These specifications are subject to change without notice.
Manual Revision 1.0
August 9, 1999
Page 2
FeaturesMVP4F
FEATURES
MVP4F Features:
•Intel Pentium® Processor, Pentium Processor with MMX technology,
AMD K6/K6-2/K6 III, Cyrix 6x86MX/MII, IDT C6/Winchip, and Rise mp6
series operating at 133 ~ 500MHz with 321 ZIF socket 7 provides
scalability to accept faster Processors in the future.
•Designed with VIA MVP4 AGPset.
•Supports up to 256 MB of DRAM (minimum of 8 MB) on board,
You can use 168-pin DIMM x 2.
•Supports (2) 32 bit PCI slots, (1) AMR Slot and provides (2) independent
high performance PCI IDE interfaces capable of supporting PIO Mode 3/4
and Ultra DMA 33/66 devices. The MVP4F supports (2) PCI Bus Master
slots and a jumperless PCI INT# control scheme which reduces configuration confusion when plugging in PCI card(s).
•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary
IDE interfaces.
•Designed with lntegrated Multi I/O: (1) floppy port, (1) parallel port
(EPP,ECP), and (2) serial ports (16550 Fast UART).
Note: Japanese “Floppy 3 mode” is also supported
•Features Award Plug & Play BIOS. With Flash Memory you can always
upgrade to the current BIOS as they are released. (http://www.
please visit our Technical Support section for the latest updates)
•MVP4F utilizes a Lithium battery which provides environmental
protection and longer battery life.
®
• Software power-down when using Windows
95/98.
2themax.com
Page 2
Page 3
FeaturesMVP4F
•Supports ring-in feature (remote power-on through external modem,
allows system to be turned on remotely).
•Resume by Alarm - Allows your system to turn on at a preselected time.
•Supports CPU Hardware sleep and SMM (System Management Mode).
•Supports USDM software to offer motherboard various status.
•Built-in WOL (Wake On
• Built-in Sound Blaster Compatible/DirectSound AC97 Audio.
• Built-in AGP 2D/3D Graphics Accelerator.
LAN) Connector.
Page 3
Page 4
InstallationMVP4F
MVP4F Detailed Layout
Page 4
Figure 1
Page 5
InstallationMVP4F
Easy Installation Procedure
The following must be completed before powering on your new system:
Configure Jumpers
System Memory Configuration
Device Connectors
Configure Jumpers
We design this motherboard with the fastest jumpers to make your install fast and
easy.
Note: The jumpers as depicted as shown (Figure 1) in their correct physical orientation.
JP2: CPU Vcore Voltage Selection
2PJerocVUPC
7-1V0.2
8-2V2.2
9-3V4.2
01-4V8.2
11-5V9.2
21-6V2.3
2.0V
2.2V
2.4V
2.8V
2.9V
3.2V
JP2
17
SW1: CPU Speed Selection
SW1
1234
NOzHM66
NONOzHM38
NONOzHM09
NONONOzHM001
NONONOzHM501
NONONOzHM511
1WS
NONOzHM59
suB
kcolC
NOzHM57
1WS
567
NOX2
NONOX5.2
NOX3
NONOX4
NONONOX5.4
NONOX533.2
NOX5.566.2
UPC
reilpitluM
X5.3
UPC
6CTDI/xiryC/DMA
reilpitluM
2pihCniWTDI
Page 5
Page 6
InstallationMVP4F
CPU TypeSW1
Pentium/MMX
AMD K6/K6-2/K6III
IDT-C6
166MHzPR200ONONON66MHz
250MHzPR366300MHz*PR366ONONONONON100MHz
200MHzPR266200MHzONON66MHz
250MHzPR333266MhzONONON83MHz
300MHz*PR433*PR400ONONONON100MHz
233MHzPR300233MHzON66MHz
333MHz*PR466*PR433ONON95MHz
350MHz*PR500*PR466ONONON100MHz
266MHz*PR333266MHzONONON66MHz
333MHz*PR466ONONONON83MHz
380MHz*PR533ONONONON95MHz
400MHz*PR550ONONONONON100MHz
300MHzONONONON66MHz
450MHzONONONONONON100MHz
333MHzONONON66MHz
*500MHz266MHzONONONONON100MHz
366MHzONON66MHz
*550MHz300MHzONONONON100MHz
Cyrix /IBM
6x86MX/MII
PR233ONONON75MHz
PR266233MHzONONONON83MHz
PR300*PR333ONONONON95MHz
PR300225MHzONON75MHz
PR400*PR380ONONON95MHz
PR333ON75MHz
*PR400ONON83MHz
*PR400ONONON75MHz
IDT Winchip 2Rise MP6
1234567
CPU
Bus
Clock
CPU
Multiplier
2.5X
3X
3.5X
4X
4.5X
5X475MHzONONONON95MHz
5.5X
* Reserved
J7
Page 6
WOL (Wakup On LAN) Connector
Reserved for NIC (Network Interface Card) to
Wake the System.
Page 7
InstallationMVP4F
System Memory Configuration
Memory Layout
The MVP4F supports (2) 168-pin DIMMs (Dual In-line Memory Module).
The DIMMs can be either EDO (Extended Data Out) or SDRAM (Synchronized
DRAM). The DIMMs may be installed using just one chip.
• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or
125MHz (8ns) bus speed.
• If you use both 50ns and 60ns memory you must configure
your BIOS to read 60ns.
• When using Synchronous DRAM we recommend using the
4 clock variety over the 2 clock.
Figure 2 and Table 1 show several possible memory configurations using
DIMM 1
DIMM 2
Bank 0/1
Bank 2/3
-Synchronous
-EDO
Figure 2
yromeMlatoT
BM821=
mumixaM
BM652=
mumixaM
1MMID
)1/0knaB(
*MARDS/ODE
1XBM821
*MARDS/ODE
1XBM821
,BM46,BM23,BM61,BM8
enoN
,BM46,BM23,BM61,BM8
2MMID
)3/2knaB(
*MARDS/ODE
,BM46,BM23,BM61,BM8
1XBM821
Table 1
* SDRAM only supports 8, 16, 32, 64, 128MB DIMM modules.
* We recommend to use PC100 Memory Module for bus speed between
66MHz and 100MHz.
Page 7
Page 8
Device Connectors
Please install the motherboard into the chassis.
InstallationMVP4F
parallel port
PS/2 Mouse
PS/2
KEYBOARD
J2:Chassis Panel Connector
• Power LED, Speaker, Reset
J3:Power_ON/OFF, Turbo LED, HDD LED, IR Connector
J4:CPU Fan Power
• A plug-in for the CPU Fan Power
J6:Chassis Fan Power
• A plug-in for the chassis Fan Power
J7:WOL (Wake On
IDE1: Primary IDE Connector
USB port
COM1VGA1
Figure 6
LAN) Connector
Speaker
Joystick/Midi
Line_in
MIC
IDE2: Secondary IDE Connector
FDD1: Floppy Controller Connector
PW1: ATX Power Connector
• 20-pin power connector
CD1: CD-ROM Audio_in Connector
MODEM1: Telephony Connector
• Pin1(Audio_in), Pin2/Pin3(GND), Pin4(Mic-out to Modem)
Page 8
Page 9
InstallationMVP4F
Device Connectors (continued)
(This is connected to the power button on the case. Using the
Soft-Off by Pwr-BTTN feature, you can choose either Instant
immediately), or 4 sec delay (you need to
J3
Off (turns system off
hold the button down for 4 seconds before the system turns off).
When the system is in 4 sec delay mode, there is a special feature
to make the system to go into suspend mode when the button is
pressed momentarily.)
Power On/Off
1
T urbo LED indicator - LED ON when higher speed is selected
+
IDE LED indicator - LED ON when Onboard PCI IDE Hard
+
disks is activate
IR Connector
1. VCC 4. GND
2. NC 5. IRTX
3. IRRX
1
J2
Page 9
Power LED - Power LED connector
1. Power LED(+)4. NC
2. N/C5. GND
3. GND
1
Speaker - Connect to the system's speaker for beeping
1. Speaker3. GND
2. N/C4. GND
1
Reset - Closed to restart system.
1
Loading...