EPCOS B43508A5107 Datasheet

Page 1
Aluminum electrolytic capacitors
Snap-in capacitors
Series/Type: B43508
Date: October 2007
© EPCOS AG 2007. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited.
Page 2
Snap-in capacitors B43508
Ultra compact 105 °C
Long-life grade capacitors
Applications
Features
Extremely high CV product, ultra compact High reliability High ripple current capability Different case sizes available for each capacitance value
Construction
Charge/discharge-proof, polar Aluminum case, fully insulated Snap-in solder pins to hold component in place on PC-board Minus pole marking on case surface Minus pole not insulated from case Overload protection by safety vent on the base
Terminals
Standard version with 2 terminals, 2 lengths available: 6.3 and 4.5 mm 3 terminals to ensure correct insertion: length 4.5 mm
Important notes at the end of this document.
Page 2 of 17Please read Cautions and warnings and
Page 3
Specifications and characteristics in brief
B43508
Ultra compact 105 °C
Rated voltage V Surge voltage V
R
S
200 ... 450 V DC
1.15 VR(for VR≤ 250 V DC)
1.10 VR(for VR≥ 400 V DC)
Rated capacitance CR82 ... 2700 µF Capacitance tolerance ±20% M Dissipation factor tan δ VR≤ 250 V DC: tan δ ≤ 0.15 (20 °C, 120 Hz) VR≥ 400 V DC: tan δ ≤ 0.20 Leakage current I
leak
(5 min, 20 °C) Self-inductance ESL Approx. 20 nH
Useful life Requirements: 105 °C, VR, I 85 °C, VR, I
AC,R
AC, max
40 °C, VR, 1.9 I
AC,R
> 3000 h C/C ≤ ±30% of initial value > 6500 h tan δ 3 times initial specified limit > 200000 h I
leak
initial specified limit
Load life test Post test requirements 105 °C, VR, I
AC,R
2000 h C/C ≤ ±20% of initial value
tan δ 2 times initial specified limit I
leak
initial specified limit
Voltage endurance test 2000 h Post test requirements: 85 °C, V
R
C/C ≤ ±10% of initial value tan δ 1.3 times initial specified limit
Vibration resistance test
I
leak
To IEC 60068-2-6, test Fc: Displacement amplitude 0.35 mm, frequency range 10 Hz ... 55 Hz,
initial specified limit
acceleration max. 5 g, duration 3 × 2 h. Capacitor mounted by its body which is rigidly clamped to the work surface.
Characteristics at low
Impedance ratio: 7 (at VR≤ 250 V DC)
temperature IEC climatic category To IEC 60068-1:
VR≤ 250 V DC: 40/105/56 (40 °C/+105 °C/56 days damp heat test) VR≥ 400 V DC: 25/105/56 (25 °C/+105 °C/56 days damp heat test) The capacitors can be operated in the temperature range of 40 °C to +105 °C but the impedance at 40 °C should be taken into consideration.
Detail specification Sectional specification
Similar to CECC 30301-809 IEC 60384-4
13 (at VR≥ 400 V DC)
Important notes at the end of this document.
Page 3 of 17Please read Cautions and warnings and
Page 4
B43508
Ultra compact 105 °C
Dimensional drawings
Snap-in terminals, length 6.3 ±1 mm. Also available in a shorter version with a length of 4.5 1 mm. For packing mode and ordering example see next page.
Dimensions (mm) Approx d +1 l ±2
weight(g)
Packing units (pcs.)
22 25 9 160 22 30 12 160 22 35 15 160 22 40 18 160 22 45 20 160 22 50 24 160 25 25 13 130 25 30 17 130 25 35 19 130 25 40 22 130 25 45 25 130 25 50 29 130 25 55 32 130
Important notes at the end of this document.
Snap-in capacitors are also available with 3 terminals (length 4.5 1 mm). For packing mode and ordering example see next page.
Dimensions (mm) Approx d +1 l ±2
weight(g)
Packing units (pcs.)
30 25 17 80 30 30 23 80 30 35 29 80 30 40 36 80 30 45 41 80 30 50 46 80 30 55 53 80 35 25 22 60 35 30 29 60 35 35 36 60 35 40 41 60 35 45 56 60 35 50 70 60 35 55 81 60
Page 4 of 17Please read Cautions and warnings and
Page 5
Packing of snap-in capacitors
B43508
Ultra compact 105 °C
For ecological reasons the packing is pure cardboard. Components can be withdrawn (in full or in part) in the correct position for insertion.
Ordering codes for terminal styles
Snap-in capacitors
Identification in 3rd block of ordering code
Terminal versions Standard terminals (6.3 ±1) mm M000 Short terminals (4.5 1) mm M007 3 terminals (4.5 1) mm M002
Ordering examples:
B43508A5107M007 } snap-in capacitor with short terminals B43508A5107M002 } snap-in capacitor with 3 terminals
Important notes at the end of this document.
Page 5 of 17Please read Cautions and warnings and
Page 6
B43508
Ultra compact 105 °C
Overview of available types
VR(V DC) 200 250 400 450
Case dimensions d × l (mm)
CR(µF)
82 22 × 25
100 22 × 25 22 × 30
25 × 25
120 22 × 30 22 × 35
25 × 30
150 22 × 30
25 × 25
22 × 40 25 × 30 30 × 25
180 22 × 35
25 × 30
22 × 45 25 × 35 30 × 30
220 22 × 25 22 × 40
25 × 35 30 × 25
22 × 50 25 × 40 30 × 30 35 × 25
270 22 × 30 22 × 50
25 × 40 30 × 30
330 22 × 25 22 × 30
25 × 25
25 × 45 30 × 35 35 × 25
390 22 × 30
25 × 25
22 × 35 25 × 30
25 × 50 30 × 35
25 × 50 30 × 35 35 × 30
25 × 55 30 × 40 35 × 35
30 × 45 35 × 35
35 × 30
470 22 × 35
25 × 30
22 × 40 25 × 30
30 × 40 35 × 35
30 × 55 35 × 40
30 × 25
560 22 × 35
25 × 30
22 × 45 25 × 35
30 × 50 35 × 40
35 × 45
30 × 30
680 22 × 40
25 × 35 30 × 25
22 × 50 25 × 40 30 × 30
30 × 55 35 × 45
35 × 55
35 × 25
Important notes at the end of this document.
Page 6 of 17Please read Cautions and warnings and
Page 7
B43508
Ultra compact 105 °C
VR(V DC) 200 250 400 450
Case dimensions d × l (mm)
CR(µF)
820 22 × 50
25 × 40 30 × 30
25 × 45 30 × 35 35 × 30
35 × 50
35 × 25
1000 25 × 45
30 × 35 35 × 30
1200 25 × 50
30 × 40
25 × 55 30 × 40 35 × 30
30 × 45 35 × 35
35 × 55
35 × 30
1500 30 × 45
35 × 35
1800 30 × 50
30 × 55 35 × 40
35 × 50
35 × 40 2200 35 × 45 35 × 55 2700 35 × 55
The capacitance and voltage ratings listed above are available in different cases upon request. Other voltage and capacitance ratings are also available upon request.
Important notes at the end of this document.
Page 7 of 17Please read Cautions and warnings and
Page 8
B43508
Ultra compact 105 °C
Technical data and ordering codes
C
R
100 Hz 20 °C µF
Case dimensions d × l mm
ESR
typ
100 Hz 20 °C m
Z
max
10 kHz 20 °C m
I
AC,max
100 Hz 60 °C A
I
AC,max
100 Hz 85 °C A
1)
I
AC,R
100 Hz 105 °C A
Ordering code (composition see below)
VR= 200 V DC
330 22 × 25 350 480 2.85 2.13 1.05 B43508A2337M00* 390 22 × 30 300 400 3.23 2.42 1.19 B43508A2397M00* 390 25 × 25 300 400 3.19 2.39 1.18 B43508B2397M00* 470 22 × 35 250 340 3.68 2.75 1.36 B43508A2477M00* 470 25 × 30 250 340 3.65 2.73 1.35 B43508B2477M00* 560 22 × 35 210 280 4.02 3.00 1.48 B43508A2567M00* 560 25 × 30 210 280 3.99 2.98 1.47 B43508B2567M00* 680 22 × 40 170 230 4.56 3.41 1.69 B43508A2687M00* 680 25 × 35 170 230 4.55 3.40 1.68 B43508B2687M00* 680 30 × 25 170 230 4.02 3.00 1.48 B43508C2687M00* 820 22 × 50 140 200 5.28 3.95 1.95 B43508A2827M00* 820 25 × 40 140 200 5.16 3.86 1.91 B43508B2827M00* 820 30 × 30 140 200 4.60 3.44 1.70 B43508C2827M00*
820 35 × 25 140 200 3.91 2.92 1.44 B43508D2827M00* 1000 25 × 45 120 160 5.85 4.38 2.16 B43508A2108M00* 1000 30 × 35 120 160 5.26 3.93 1.95 B43508B2108M00* 1000 35 × 30 120 160 4.79 3.58 1.77 B43508C2108M00* 1200 25 × 50 100 130 6.57 4.92 2.43 B43508A2128M00* 1200 30 × 40 100 130 6.33 4.74 2.34 B43508B2128M00* 1200 35 × 30 100 130 5.24 3.92 1.94 B43508C2128M00* 1500 30 × 45 75 110 7.28 5.44 2.69 B43508A2158M00* 1500 35 × 35 75 110 6.07 4.54 2.25 B43508B2158M00* 1800 30 × 50 65 90 8.18 6.12 3.02 B43508A2188M00* 1800 35 × 40 65 90 6.86 5.13 2.54 B43508B2188M00* 2200 35 × 45 55 75 7.80 5.84 2.89 B43508A2228M00* 2700 35 × 55 45 60 9.07 6.78 3.36 B43508A2278M00*
VR= 250 V DC
220 22 × 25 530 710 2.48 1.85 0.91 B43508E2227M00*
270 22 × 30 430 580 2.86 2.14 1.06 B43508E2277M00*
330 22 × 30 350 480 3.16 2.37 1.17 B43508E2337M00*
330 25 × 25 350 480 3.11 2.32 1.15 B43508F2337M00*
390 22 × 35 300 400 3.56 2.66 1.32 B43508E2397M00*
390 25 × 30 300 400 3.52 2.63 1.30 B43508F2397M00*
Composition of ordering code
* = Terminal style
0 = snap-in standard terminals (6.3 ±1) mm 2 = snap-in 3 terminals (4.5 1) mm 7 = snap-in short terminals (4.5 1) mm
1) 120-Hz conversion factor of ripple current: IAC(120 Hz) = 1.03 IAC(100 Hz)
Important notes at the end of this document.
Page 8 of 17Please read Cautions and warnings and
Page 9
B43508
Ultra compact 105 °C
Technical data and ordering codes
C
R
100 Hz 20 °C µF
Case dimensions d × l mm
ESR
typ
100 Hz 20 °C m
Z
max
10 kHz 20 °C m
I
AC,max
100 Hz 60 °C A
I
AC,max
100 Hz 85 °C A
2)
I
AC,R
100 Hz 105 °C A
Ordering code (composition see below)
VR= 250 V DC
470 22 × 40 250 340 4.03 3.02 1.49 B43508E2477M00*
470 25 × 30 250 340 3.86 2.89 1.43 B43508F2477M00*
470 30 × 25 250 340 3.48 2.60 1.29 B43508G2477M00*
560 22 × 45 210 280 4.52 3.38 1.67 B43508E2567M00*
560 25 × 35 210 280 4.37 3.27 1.62 B43508F2567M00*
560 30 × 30 210 280 3.96 2.96 1.46 B43508G2567M00*
680 22 × 50 170 230 5.11 3.82 1.89 B43508E2687M00*
680 25 × 40 170 230 4.97 3.72 1.84 B43508F2687M00*
680 30 × 30 170 230 4.37 3.27 1.61 B43508G2687M00*
680 35 × 25 170 230 3.66 2.74 1.35 B43508H2687M00*
820 25 × 45 140 200 5.61 4.20 2.07 B43508E2827M00*
820 30 × 35 140 200 4.97 3.72 1.84 B43508F2827M00*
820 35 × 30 140 200 4.46 3.33 1.65 B43508G2827M00* 1000 25 × 55 120 160 6.49 4.86 2.40 B43508E2108M00* 1000 30 × 40 120 160 6.03 4.51 2.23 B43508F2108M00* 1000 35 × 30 120 160 4.92 3.68 1.82 B43508G2108M00* 1200 30 × 45 100 130 6.79 5.08 2.51 B43508E2128M00* 1200 35 × 35 100 130 5.59 4.18 2.07 B43508F2128M00* 1500 30 × 55 75 110 7.96 5.96 2.95 B43508E2158M00* 1500 35 × 40 75 110 6.44 4.82 2.38 B43508F2158M00* 1800 35 × 50 65 90 7.44 5.57 2.75 B43508E2188M00* 2200 35 × 55 55 75 8.42 6.30 3.12 B43508E2228M00*
VR= 400 V DC
100 22 × 25 1230 1730 1.63 1.22 0.60 B43508A9107M00*
120 22 × 30 1020 1440 1.87 1.39 0.69 B43508A9127M00*
150 22 × 30 820 1150 2.09 1.56 0.77 B43508A9157M00*
150 25 × 25 820 1150 2.09 1.56 0.77 B43508B9157M00*
180 22 × 35 680 960 2.37 1.77 0.87 B43508A9187M00*
180 25 × 30 680 960 2.39 1.79 0.88 B43508B9187M00*
220 22 × 40 560 790 2.70 2.02 1.00 B43508A9227M00*
220 25 × 35 560 790 2.74 2.05 1.01 B43508B9227M00*
220 30 × 25 560 790 2.65 1.98 0.98 B43508C9227M00*
270 22 × 50 460 640 3.15 2.35 1.16 B43508A9277M00*
Composition of ordering code
* = Terminal style
0 = snap-in standard terminals (6.3 ±1) mm 2 = snap-in 3 terminals (4.5 1) mm 7 = snap-in short terminals (4.5 1) mm
2) 120-Hz conversion factor of ripple current: IAC(120 Hz) = 1.03 IAC(100 Hz)
Important notes at the end of this document.
Page 9 of 17Please read Cautions and warnings and
Page 10
B43508
Ultra compact 105 °C
Technical data and ordering codes
C
R
100 Hz 20 °C µF
Case dimensions d × l mm
ESR
typ
100 Hz 20 °C m
Z
max
10 kHz 20 °C m
I
AC,max
100 Hz 60 °C A
I
AC,max
100 Hz 85 °C A
3)
I
AC,R
100 Hz 105 °C A
Ordering code (composition see below)
VR= 400 V DC
270 25 × 40 460 640 3.13 2.34 1.16 B43508B9277M00*
270 30 × 30 460 640 3.06 2.29 1.13 B43508C9277M00*
330 25 × 45 370 530 3.56 2.66 1.31 B43508A9337M00*
330 30 × 35 370 530 3.50 2.62 1.29 B43508B9337M00*
330 35 × 25 370 530 3.20 2.39 1.18 B43508C9337M00*
390 25 × 50 320 450 3.96 2.96 1.46 B43508A9397M00*
390 30 × 35 320 450 3.81 2.85 1.41 B43508B9397M00*
390 35 × 30 320 450 3.86 2.88 1.43 B43508C9397M00*
470 30 × 40 260 370 4.59 3.44 1.70 B43508A9477M00*
470 35 × 35 260 370 4.39 3.28 1.62 B43508B9477M00*
560 30 × 50 220 310 5.29 3.95 1.96 B43508A9567M00*
560 35 × 40 220 310 4.94 3.70 1.83 B43508B9567M00*
680 30 × 55 180 260 5.96 4.46 2.20 B43508A9687M00*
680 35 × 45 180 260 5.60 4.19 2.07 B43508B9687M00*
820 35 × 50 150 210 6.31 4.72 2.33 B43508A9827M00* 1000 35 × 55 120 180 7.13 5.33 2.64 B43508A9108M00*
VR= 450 V DC
82 22 × 25 1500 2100 1.58 1.18 0.58 B43508A5826M00* 100 22 × 30 1230 1730 1.82 1.36 0.67 B43508A5107M00* 100 25 × 25 1230 1730 1.82 1.36 0.67 B43508B5107M00* 120 22 × 35 1020 1440 2.07 1.54 0.76 B43508A5127M00* 120 25 × 30 1020 1440 2.08 1.55 0.77 B43508B5127M00* 150 22 × 40 820 1150 2.38 1.78 0.88 B43508A5157M00* 150 25 × 30 820 1150 2.33 1.74 0.86 B43508B5157M00* 150 30 × 25 820 1150 2.39 1.79 0.88 B43508C5157M00* 180 22 × 45 680 960 2.68 2.01 0.99 B43508A5187M00* 180 25 × 35 680 960 2.64 1.97 0.97 B43508B5187M00* 180 30 × 30 680 960 2.73 2.04 1.01 B43508C5187M00* 220 22 × 50 560 790 3.04 2.27 1.12 B43508A5227M00* 220 25 × 40 560 790 3.01 2.25 1.11 B43508B5227M00* 220 30 × 30 560 790 3.02 2.26 1.11 B43508C5227M00* 220 35 × 25 560 790 2.89 2.16 1.07 B43508D5227M00* 270 25 × 50 460 640 3.51 2.63 1.30 B43508A5277M00*
Composition of ordering code
* = Terminal style
0 = snap-in standard terminals (6.3 ±1) mm 2 = snap-in 3 terminals (4.5 1) mm 7 = snap-in short terminals (4.5 1) mm
3) 120-Hz conversion factor of ripple current: IAC(120 Hz) = 1.03 IAC(100 Hz)
Important notes at the end of this document.
Page 10 of 17Please read Cautions and warnings and
Page 11
B43508
Ultra compact 105 °C
Technical data and ordering codes
C
R
100 Hz 20 °C µF
Case dimensions d × l mm
ESR
typ
100 Hz 20 °C m
Z
max
10 kHz 20 °C m
I
AC,max
100 Hz 60 °C A
I
AC,max
100 Hz 85 °C A
4)
I
AC,R
100 Hz 105 °C A
Ordering code (composition see below)
VR= 450 V DC
270 30 × 35 460 640 3.47 2.59 1.28 B43508B5277M00* 270 35 × 30 460 640 3.55 2.65 1.31 B43508C5277M00* 330 25 × 55 370 530 3.97 2.97 1.47 B43508A5337M00* 330 30 × 40 370 530 4.21 3.15 1.56 B43508B5337M00* 330 35 × 35 370 530 4.06 3.04 1.50 B43508C5337M00* 390 30 × 45 320 450 4.71 3.52 1.74 B43508A5397M00* 390 35 × 35 320 450 4.42 3.30 1.63 B43508B5397M00* 470 30 × 55 260 370 5.42 4.05 2.00 B43508A5477M00* 470 35 × 40 260 370 5.00 3.74 1.85 B43508B5477M00* 560 35 × 45 220 310 5.62 4.20 2.08 B43508A5567M00* 680 35 × 55 180 260 6.50 4.86 2.40 B43508A5687M00*
Composition of ordering code
* = Terminal style
0 = snap-in standard terminals (6.3 ±1) mm 2 = snap-in 3 terminals (4.5 1) mm 7 = snap-in short terminals (4.5 1) mm
4) 120-Hz conversion factor of ripple current: IAC(120 Hz) = 1.03 IAC(100 Hz)
Important notes at the end of this document.
Page 11 of 17Please read Cautions and warnings and
Page 12
B43508
Ultra compact 105 °C
Useful life
depending on ambient temperature TAunder ripple current operating conditions
Frequency factor of permissible ripple current IACversus frequency f
Frequency characteristics of ESR
Typical behavior
1)
1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs.
Important notes at the end of this document.
Page 12 of 17Please read Cautions and warnings and
Page 13
Impedance Z versus frequency f
Typical behavior at 20 °C
B43508
Ultra compact 105 °C
Important notes at the end of this document.
Page 13 of 17Please read Cautions and warnings and
Page 14
B43508
Ultra compact 105 °C
Cautions and warnings
Personal safety
The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC).
Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited.
As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors:
Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water.
Important notes at the end of this document.
Page 14 of 17Please read Cautions and warnings and
Page 15
B43508
Ultra compact 105 °C
Product safety
The table below summarize the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information".
Topic Safety information Reference
Chapter "General technical information"
Polarity Make sure that polar capacitors are connected
with the right polarity.
1 "Basic construction of aluminum electrolytic capacitors"
Reverse voltage Voltages polarity classes should be prevented by
connecting a diode.
Upper category
Do not exceed the upper category temperatur. 7.2
temperature
3.1.6 "Reverse voltage"
"Maximum permissible operating temperature"
Maintenance Make periodic inspections of the capacitors.
Before the inspection, make sure that the power
10
"Maintenance" supply is turned off and carefully discharge the electricity of the capacitors. Do not apply any mechanical stress to the capacitor terminals.
Mounting position of screw terminal capacitors
Do not mount the capacitor with the terminals (safety vent) upside down.
11.1.
"Mounting positions of
capacitors with screw
terminals"
Mounting of single-ended capacitors
The internal structure of single-ended capacitors might be damaged if excessive force is applied to the lead wires. Avoid any compressive, tensile or flexural stress.
11.4
"Mounting
considerations for
single-ended capacitors" Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified.
Robustness of terminals
The following maximum tightening torques must not be exceeded when connecting screw
11.3
"Mounting torques" terminals: M5: 2 Nm M6: 2.5 Nm
Soldering Do not exceed the specified time or temperature
limits during soldering.
11.5
"Soldering"
Important notes at the end of this document.
Page 15 of 17Please read Cautions and warnings and
Page 16
B43508
Ultra compact 105 °C
Topic Safety information Reference
Chapter "General
technical information"
Soldering, cleaning agents
Passive flammability
Active flammability
Do not allow halogenated hydrocarbons to come into contact with aluminum electrolytic capacitors.
11.6
"Cleaning agents" Avoid external energy, such as fire or electricity. 8.1
"Passive flammability" Avoid overload of the capacitors. 8.2
"Active flammability"
Reference
Chapter "Capacitors
with screw terminals"
Breakdown strength of insulating
Do not damage the insulating sleeve, especially when ring clips are used for mounting.
"Screw terminals -
accessories"
sleeves
Important notes at the end of this document.
Page 16 of 17Please read Cautions and warnings and
Page 17
Important notes
The following applies to all products named in this publication:
1. Some parts of this publication contain statements about the suitability of our products for
certain areas of application. These statements are based on our knowledge of typical re-
quirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incum­bent on the customer to check and decide whether an EPCOS product with the properties de­scribed in the product specification is suitable for use in a particular customer application.
2. We also point out that in individual cases, a malfunction of passive electronic compon-
ents or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applica-
tions requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component.
3. The warnings, cautions and product-specific notes must be observed.
4. In order to satisfy certain technical requirements, some of the products described in this
publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as hazardous). Useful information on this will be found in our Ma-
terial Data Sheets on the Internet (www.epcos.com/material). Should you have any more de­tailed questions, please contact our sales offices.
5. We constantly strive to improve our products. Consequently, the products described in this
publication may change from time to time. The same is true of the corresponding product
specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. The aforementioned does not apply in the case of individual agreements deviating from the fore­going for customer-specific products.
6. Unless otherwise agreed in individual contracts, all orders are subject to the current ver-
sion of the “General Terms of Delivery for Products and Services in the Electrical In­dustry” published by the German Electrical and Electronics Industry Association (ZVEI).
7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, MiniBlue, MKK,
MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks.
Page 17 of 17
Loading...