Eonon TFT LCD Color TV Operating Instructions Manual

Page 1
TFT LCD COLOR TVTFT LCD COLOR TV
Operating instructions
Before operating this set, please read these instructions completely
PO
WE
R
MENU
/AV
M
O
T
E
E
R
CH
-
CH
+
TFT LC
D CO
LOR TV
TFT LC
D CO
LOR TV
Page 2
- 1 -
Welcome your using of our on-board TFT LCD Color TV. Please carefully read this Instruction for a fully and long-term using for no troubles. Please well reserve it for future use.
Important Cautions
1. Please ensure that all requirements are meet before operating.
2. The LCD cannot be installed where sight of driver is adversely affected against safe operation.
3. If troubles occurred please do not disassemble the LCD instead of contacting dealers or authorized service center. For electric shock or other dangers that may be generated by inside high-pressure parts, the installation or maintenance must be carried out by professional maintenance people.
4. Please ensure that dampness and impact are away kept from.
5. Please do not use alcohol or other chemical cleansers instead of soft dry cloth to clean dirt on it.
6. Please keep it in -20 C~+60 C and operate it in 5 C~40 C.
o o o o
During running, a few of dots or dark dots may appear, which is normal other than troubles in source matrix display technology.
In low temperature, the pictures may be much darker when power is on, which is not trouble.
Special attention
Considering your safe, please do not watch TV when driving. Operating or watching during driving is forbidden under some countries' laws.
Warning
TFT LCD COLOR TV TFT LCD COLOR TV
Page 3
- 21 - - 2 -
CT-V70W8: NTSC Organic PAL Organic VL 55.25-163.25MHZ 49.75-160.25MHZ VH 163.25-469.25MHZ 160.25-464.25MHZ UHF 471.25-855.25MHZ 471.25-863.25MHZ
1. Extension switch
2. Remote-controlled receiving window
3. Power switch
4. Menu
5. Function selection (TV/AV1/AV2)
6. Power indicator light
7. Clock
8. Channel +
9. Channel -
Name: 7-inch TFT LCD COLOR TV
System: CT-V70W8P: PAL (B/G. H. D/K. I) CT-V70W8N: NTSC-M
Display device: Color TFT-LCD Screen dimension: Broad 7-inch Pixel: 150MW (MAX) Loudspeaker: Built-in Back light source: high-brightness cold cathode fluorescent tube Ports: external connect to antenna input port
Earphone port Audio output port
USB (audio and video input) Port External power input port Power supply: 2 optional power supplies
AC-AC adapter Vehicle accumulator-vehicle adapter
Power consumption: About 12W
POWER
MENU
TV/AV
M
O
T
E
E
R
CH-
CH+
T
FT
LC
D C
OLOR
T
V
T
FT
LC
D C
OLOR
T
V
2
394
8
5
6
OPEN
7
1
TFT LCD
COLOR TV
Appearance and functions
Descriptions for function keys
12. Specifications and Parameters
TFT LCD COLOR TV TFT LCD COLOR TV
Page 4
- 20 -- 3 -
Please refer to the Body Figure
Fuse 2A
Yellow wire - accumulator of 12V
Black wire -- grounding
Red wire --ACC switch
Green wire - backing-up control wire
White wire - video frequency V2 Red wire - audio input
Yellow wire - video frequency V1 Antenna input port 1
Antenna input port 2
Please connect backing-up camera head from V2 white import, when green wire is connected to backing-up signal lamp (12V); When backing-up, automatically entered into V2, and after backing-up, original state returned.
Descriptions
Reasons
No pictures or sounds
AC adapter or vehicle adapter are wrongly connected. Uncertified power is under using. If TV/AV is correctly selected?
No pictures
If channel is rightly selected? Auto reset receiving channel. Reset channel in other new places.
No sounds
If volume is rightly adjusted? If earphone has been connected? Signal and mute are under functions.
Poor contact
If antenna is rightly adjusted? If channel is rightly adjusted?
Dark picture
If brightness and contrast are rightly adjusted? If ambient temperature is too low?
Blur picture
or non-stable
If antenna is rightly adjusted? Maybe received local signal is too weak.
Double image
If antenna direction is right? Maybe signals reflected by nearby buildings or high walls are received.
Blur pots
Maybe interfered by electric wave of motors of vehicles, trains, high-pressure wires and neon lamps.
No colors
If color adjustment is under good state? For poor signal achromatic in under function
No operation of
remote controller
If batteries have been used up? If receiver has exposed on violent light?
Installation and connection methods
Warning
Figure of installing batteries into remote controller
TFT LCD COLOR TV TFT LCD COLOR TV
Page 5
- 19 -
- 4 -
1 2 3
4
5 6
7
9
8
10
11
(6). Menu (7). Selection (8). Volume + (9). Volume ­(10). Direct channel selection (11). Digital channel selection
(1). Mute (2). Power on (3). Channel + (4). Channel ­(5). Function selection (TV/AV1/AV2)
SKIP Function
1. Press MENU for seconds and PRESET mode will appear.
2. Press CH+ or CH- to select SKIP options.
3. Press V+ or V-, the mode will convert in following turns
ON OFF, and programme number set to ON will be set to SKIP, if you want to close SKIP off, you may first choose programme number and set SKIP mode to OFF.
4. Press MENU for 2 times or 10 seconds after menu will auto
disappears to return to normal state.
Please connect connector plug of earphone to jack of earphone.
Close down LCD TV: press POWER. Turn on LCD TV: press POWER or CH+ or CH-. AUTO POWER OFF: in TV state no signals or operation
carried within 10 minutes, power of TV will be auto closed down.
Timely Off: Press SLEEP for 0-10 90 minutes and power will be on.
(1). Press MENU for 3 seconds, and PRESET mode will
appear. (2). Press MENU again and SET picture will appear. (3). Press V+ or V- to select normal picture display or up or
down.
Press MIRROR on remote controller or N/R on this set to select normal picture display or to right or left.
f following phenomena appear, please according to following methods carry out check before repair asked.
Remote controller
MIRROR
7. Usage of Earphone
8. ON/OFF
9. UP or DOWN for picture
10. To Right or Left
11. Before repair asked
TFT LCD COLOR TV TFT LCD COLOR TV
Page 6
- 5 -
- 18 -
1. Standby key (remote control)
1). Functions: standby or to normal state
2). Description: When power is on, the TV is under standby state. To push standby key for converting between standby
state and normal state. During standby state other keys are off except standby
key. Starting the TV signals of factory will be found.
2. TV/AV (remote control and owned key)
1). Functions: Converting between TV mode and AV mode
2). Description: With two-way AV input. To push this key for converting between TV state and
AV state. Under AV state, if you push numeric keys such as 0-9, -,
-, CH+, CH-, and RECALL, it will be valid return to relevant TV channel.
3. 0~9 (remote control)
1). Functions: Directly select programme / swiftly select adjustment items.
2). Description: For 0~9 programme please directly push 0-9 keys; for
10-255. Programme please firstly press (- -) key to select double
bits or 3 bits, and then with (0~9) key to log into hundred bit, tens bit, and ones bit in turn.
If your selection is beyond 255, the key is invalid. After change, current programme number and the last
time shall be changed and will be auto written into EEPROM.
For the LCD TV you can use Screen Display to adjust picture and sound, and set up channel and other characteristics. Please refer to following required items and set them up.
Preset channel: 256 channels can be memorized
Auto View & Memory
To set up favorable channel
1. Press MENU for 3 seconds then PRESET mode will appear.
2. Press CH+ or CH to select BAND options, and press V+ or V- to select favorable reset band.
3. Press CH+ or CH to select SEARCH options ahead or backward from current channel, which should not be stopped until TV signal received.
4. Press MENU for another 2 times or after 10 seconds menu will auto disappear to return to normal state.
Fine Tuning for Frequency
1. Press MENU for 3 seconds and PRESET mode will appear.
2. Press CH+ or CH- to select CH options and press V+ or V­to select favorable Fine-Tuning programme number.
3. Press CH+ or CH- to select FINE TUNE options and press V+ or V- for continuous fine-tuning until your consent picture appears.
4. Press MENU for another 2 times or after 10 seconds menu will auto disappear to return to normal state.
Method 1: Press AUTO of report controller and PRESET mode
will appear, and then press AUTO for auto view and memory. The selected channels will be memorized in programme number for example 1, 2, 3 . After auto view, the picture shows programme 1.
Method 2: Press MENU for 3 seconds then PRESET will
appear, and then press V+ or V- for auto view and memory.
3. Key functions and display descriptions 6. Reset Receiving Channel
TFT LCD COLOR TV TFT LCD COLOR TV
Page 7
- 17 -
- 6 -
If you select the same number with current programme number, CPU will reread memory information relevant to current programme number from EEPROM.
During programme being converted, (0-9) keys may be used for directly selecting the programme number required.
4. CH+, CH- / PROGRAMME+; PROGRAMME (remote control and owned key).
1). Functions: Programme number + / -, selection in menu, selection of adjustment items, function of calendar.
2). Description: With CH+ / CH- to change programme number, and
programme number of SKIP ON will be appeared. If all programme numbers are under SKIP ON state,
push CH+ / CH- key to select programme 0 only. If only one programme number is under SKIP ON state, push CH+ / CH- key to select this programme.
If CH+ has arrived at the largest programme number, push again CH+ to skip to the littlest programme number; contrary to that if CH- has arrived at the littlest programme number, push again CH- to skip to the largest programme number.
After conversion current programme and the last programme number will be changed and written into EEPROM.
In full-screen menu, CH+ and CH- are used to select items in menu (Please refer to related operation instruction).
In calendar state, with CH+ and CH- to change years.
5. VOL+, VOL- / Volume+, Volume- (remote control and owned key)
1). Functions: To control volume; Adjust all items in menu; adjust all
debugging items and months of calendar.
6. Control brightness, color, contrast, and hue
MENU
V- V+
Press MENU key
Choose analog quantity, change in turn i.e. brightness color contrast hue
Screen display
If the signal is much weak, no matter how you stretch with the antenna, picture will be bad, noise, wobbling, and blur spots will show on the TV, which is not the trouble of TV itself.
Warning
hue is only can be adjusted for NTSC organic signal.
Warning
7. For the purpose of receiving clearer picture To control the length, color, and direction of antenna of pull-
rod for the best picture After that please draw back the antenna one by one.
TFT LCD COLOR TV TFT LCD COLOR TV
Page 8
- 7 -
- 16 -
CH - CH+
2
V- V+
2). Description: When it is used for controlling output value of volume, to
push it one time for increasing / decreasing one step (output value includes 100 steps).
If output value has reached the top 100, VOL+ is non­effectual, contrary to which if output value has reached 0, VOL- is non-effectual.
Under Mute State to press VOL- / + to exit. Under semi-auto search state, to press VOL- / + to
change search direction. In menu used for adjusting all options. Under calendar state used for changing months.
6. MUTE (remote control)
1). Functions: Mute
2). Description: Press MUTE key for sound disappearing again pressing
for exit. Press Power key and VOL+ / - to exit. When in MUTE state if no other OSD display, OSD
display of MUTE will be kept.
7. MENU (remote control and owned key)
1). Functions: Enter or exit to main menu.
2). Operation description for MENU key. After entering main menu, press CH+/CH- for converting
all sub menus Under auto search or semi-auto search state, press
MENU for stopping.
3). (Trees displayed in following pictures is not exited in actual OSD).
Press Channel View key
Converted by the turn of C 99-98-97
Converted by the turn of C 1-2-3
Long-time press for continuous change, screen displays
1. Four ASPECTs for your favorable selections.
1). Method 1: Press VIEW MODE to choose display mode.
2). Method 2: Press MENU for 3 seconds then PRESET will be found again.
Press MENU again SET will be found. Press CH+ or CH- to choose ASPECT items. Press V+ or V- to choose display mode.
5. Volume Control
Press Volume Key
-
TFT LCD COLOR TV TFT LCD COLOR TV
Page 9
- 15 -
- 8 -
V
BRIGHTNESS CONTRAST COLOR SHARPNESS TINT
50 50 50 50 50
I
50 50 50 50
Main menu consists of pictures, sounds, setting and time. Press V+ and V- to select menu required. When a menu is selected, the icon is extruded, and name of menu and options of menu will be found at the bottom. Before entering sub­menus, option shows yellow. After selection, press CH+ and CH- to enter sub menu, under which, press MENU to return to main menu state, or you can press CH- in the first option of menu to return to main menu.
Housing AC Please provide power source from housing standard power by
AC adapter (please refer to Instruction of Adapter). Vehicle accumulator (DC 12V) Please provide power source from vehicle accumulator
through vehicle cigar lighter by vehicle adapter (be applicable for cathode ground).
1. Connect to power supply, press power switch or CH+ or CH- to turn on the TV.
2. Press AV/TV to choose signal input sources of TV, AV1 and AV2.
3. If you choose TV, please pull out antenna of pull-rod.
4. Press Channel View key to choose your favourable channel.
BRIGHTNESS CONTRAST COLOR SHARPNESS
Picture Menu
Main Menu
4. Power Selection
Please note that:
Please do not connect vehicle adapter to vehicle (for example trucks or buses) with 24V DC.
Please ensure that only accessary fittings are always used, otherwise other AC adapters or vehicle adapters may damage the TV.
If you have for a long time not used the TV, please draw out vehicle adapter from cigar lighter and pull out AC adapter from electrical plug on wall, otherwise the TV may be damaged or vehicle accumulator or battery package may be used up.
5. Basic operations
TFT LCD COLOR TV TFT LCD COLOR TV
Page 10
- 9 -
- 14 -
CHANNEL
PG EXCHANGE
0 0
VOLUME
50
A
U
LANGUAGE BACKGROUND
ENG ON
S
E
Press CH+ and CH+ to select items required adjusted, and V+ and V- to change parameter of adjusted items, among which hue is only appeared under NTSC organic. Press MENU to return to main menu, and parameter is adjusted from 0~100.
Press CH+ and CH- to select items required adjusted, and V+ and V- to change parameter of adjusted items. Press MENU to return to main menu, and parameter is adjusted from 0~100.
8. Channel Skip
Press V+/V- to control Skip State of current programme, when you use of CH+/CH- to convert TV channels, if you choose ON current programme will be skipped; if you choose OFF current programme will be normally changed.
9. Counterchange between Channels Press V+ to enter into the said Menu, and with V+/V- to
choose two channels required counterchanged, and then with CH+ to enter into the third line of the sub-menu, press V+ for counterchanging.
8. Auto Search
1). Functions: Directly enter into Auto Search State
2). Descriptions: Please refer to the fourth of Auto Search in menu.
Sound Menu
Set Menu up
TFT LCD COLOR TV TFT LCD COLOR TV
Page 11
- 13 -
- 10 -
VHFL
1
CALENDAR GAME
S
E
T
Press CH+ and CH- to select items required to adjust, and V+ and V- to change parameter of adjusted items. There is a drop-down strip showing that there are other options, please refer to the following picture.
1. Language Including Chinese, English, French, Russian, and German.
2. Blue Screen Blue Screen is used to determine that whether blue screen is needed to be on or not without signals.
3. Mode Three modes for selection: normal, full screen and broad screen (invalid on vehicle).
4. Up or Down To control the picture be up or down.
5. Right or Left To control the picture be right or left (invalid on vehicle)
6. Calendar Open the calendar.
7. Games Turn on sub-games in sliding box.
1. Color organic Press V+ and V- to convert between color organics.
2. Sound organic Press V+ and V- to convert between color organics.
3. Channel adjustment Press V+ and V- to select channels required adjusted.
4. Auto search
Press V+ to access to auto search state and to memory
from Channel 1. Auto mute, close down blue screen and then return to Channel 1 after search, and to press MENU to stop searching.
5. Manual search Press V+ for channels in front and V- for channels after.
After a channel is found, it will be stopped auto. Press MENU to return to Search Menu. During searching press MENU to stop this action and return to SKIP MENU.
6. Fine tuning Press V+ for channels in front and V- for channels after. At
the same time to write into EEPROM, and AFC is set to OFF State. Press MENU to return to Search Menu.
7. Converting between Frequency Channels If you use of FS high frequency, it cannot be adjusted, if
you use of VS high frequency, press V+ and V- to change different frequency channels. VHFL VHFH UHF VHFL, during converting AFC should be closed down.
TFT LCD COLOR TV TFT LCD COLOR TV
Page 12
- 11 -
- 12 -
C
L
O
CLOCK OFF ON ON CHANNEL
- -: - -
- -: - -
- -: - -
- - -
T
U
N
BAND FINE TUNE SKIP PG EXCHANGE
VHF-L
ON
a. Under game state press AV/TV to select the next game. b. Press MENU to return original state. c. Press MUTE for exiting.
Under Clock State, with V+ and V- to write into current time, and with P+ and P to select that is required to set up. Red shows that is selected option. If you set up OFF TIME, on that exact time it will be off. If it is in OFF STATE, the time setup shall be cleared and no operation will be carried out.
When you set up ON TIME, on that exact time it will be on, if it has been already on, it will carry out the command of channel­exchange to the channel set in CHANNEL ON . In time menu, press MENU to return to the menu setup.
Press CH+ or CH- to select that required adjusted, whose parameters shall be changed by pressing V+ and V-. There is a drop-down strip in the right showing that there are other options.
Clock Menu
Channel exchange menuDescriptions for games:
T
U
N
AUTO
D/K
O
C-SYS S-SYS CHANNEL ATUO INSTALL SEARCH
TFT LCD COLOR TV TFT LCD COLOR TV
Loading...