1 Only connect the unit to a 12V power supply with negative grounding.
Never install the unit where the operation for safety driving is restrained.
2
Never use the video display function in the front when driving to prevent the violation of laws
3
regulations and also to reduce the risk of traffic accident except using for rear view video camera.
Never expose the unit, amplifier, speakers to moisture or water to prevent electronic sparks or fires.
4
Please don't change the fuse in the power cord without professional guidance, improper fuse may
5
cause damage to this using unit or even cause fire.
Please power off the unit at once and send it back to the after-sales service center or the dealer/
6
distributor yo purchased from if one of the following symptoms is found:
(a)NO audio output; (b)NO image output;(c)Water or other obstacle enters the unit; (d)Smoking;
(e)Peculiar smell.
To ensure safe driving, please adjust the volume to a safe and comfort level in case of emergency
7
situations.
2
Page 4
Warnings and Precautions
Precautions
1
Never disassemble or adjust the unit without any professional guide. For details, please consult any professional car shop/
dealer for inquiry.
2
If the front panel or the TFT monitor is squalid, please use a clean silicone cloth and neutral detergent to wipe off the spot.
Using a rough cloth and non-neutral detergent such as alcohol for cleaning may result in scratching or decoloration to the
applicant.
3
If any abnormal behavior of the unit is found, please refer to trouble shooting guide of this manual. If no relevant information is
found , please press the [RESET] key on the front panel to resume factory default.
4
If you have parked the car in hot or cold weather for a long time, please wait until the temperature in the car becomes normal
before operating the unit.
5
Using in-car heater in low temperature environment may result in beads coagulate inside the unit, DO NOT use the unit in this
situation, eject the disc and wipe off the bead on the disc. If the unit still doesn
after-sales service center.
6
No fierce impact to the LCD monitor when it is in open position for preventing the damage to any mechanisms inside.
7
To prevent the damage to the screen, avoid touching it with sharp objects.
't work after a few hours, please contact with
8
The monitor employs auto motorizing mechanism, please do
to any mechanisms inside.
9
To provide a clear demonstration and an alternative for easy understanding to the operation of this unit, graphic illustrations
are used. However, these illustrations are some different from the actual images displayed in the unit.
10
During operation the unit," "is displayed if the particular operation is not available or illegal.
11
Operate the unit correctly according to this manual to prevent. Unnecessary problem. The guarantee won
problem is caused by inappropriate operation.
n't push, pull, or swivel the monitor manually to prevent damage
't be valid if the
3
Page 5
Electric Connection
Front right RCA out(Red)
Front left RCA out(White)
Back a car video in(Yellow)
Subwoofer(Brown)
Back right RCA out(Blue)
Back left RCA out(Purple)
AUX left in(White)
AUX right in(Red)
Video in(Yellow)
Video out(Yellow)
Brake detecting wire
Back car detecting wire
Remote control for amplifier.
Connect control for antenna
Ignition key
sw tchi
Car fuse box
(Main fuse)
Battery
Car Antenna
Gray
Brown
Pink
Blue
Ignition wire(Red)
Battery wire(Yellow)
Ground wire(Black) (To car chassis)
4
Orange
Front.L
Front.R
Rear.L
Rear.R
TV ANTENNAPLUG
(Without TV tuner,
without this wire.)
Light wire
White
To front left speaker
White/Black
Gray
To front right speaker
Gray/Black
Green
To rear left speaker
Green/Black
Purple
To rear right speaker
Purple/Black
Page 6
Install
Before installing the receiver, fit it in the approximate place in your car and connect the equipment according to the speakers and electrical
connections. When your system is operated properly, follow the instructions for permanent installation of your system.
1. snapclose
INSTALL THE UNIT
1. Install the snapclose.
2. Lock up the unit in a car through screwdriver.
2. screw
REMOVE THE UNIT
1. Remove the unit through screwdriver.
2. Remove the snapclose . Make the unit
deviate from the car, then take the connecting pin down.
3. screwdriver
5
Page 7
General Features
12
13
PWROPEN
1
MIC
ADJMUTENAVIBT
34
2
5
14
-
VOL
6789
15
6
VOL+
10
11
Page 8
General Features
Remote Control
Loading and replacing the battery
MIC
PWROPEN
1
1
SRC Button:
2
OPEN Button: turn down button.
3
ADJ Button:
4
MIC.
5
MUTE Button: Mute.
6
NAVI Button: switch to Navigation mode directly.
7
BT Button: switch to BT mode directly.
8
Signal received window.
9
VOL- Button:
10
VOL+Button:
11
Reset Button.
12
MapSDslot.
13
SD Slot.
14
[ ]Button: To eject the DISC.
15
USB Port.
ADJMUTENAVIBT
5
3 4
2
6789
Play SRC switch.
Display position Adjustment.
decrease volume.
increase volume.
Note: If unit not have BT, also not have mic.
-
VOL+
VOL
10
14
Pull out
11
Notes of remote control using:
Aim the remote controller at the remote sensor on the unit.
1)
Remove the battery from the remote control or insert a
2)
battery insulator if the battery has not been used for a
month or longer.
DO NOT store the remote control under direct sunlight
3)
or in high temperature environment, or it may not function
properly.
The battery can work for 6 months under normal condition.
4)
If the remote control can't work, please change the battery.
Use(button shaped) lithium battery(CR-2025)only.
5)
DO NOT recharge, disassemble, heat or expose the battery
6)
in fire.
Insert the battery in proper direction according to the
7)(+)
and(-)poles.
Store the battery in a place where children cannot reach to
8)
avoid risk of accident.
7
Page 9
Remote Control
Button and Function
REC
Sub-T
SEL
Setup
2
ABCDEF
56
JKL
89
WXYZ
TUV
0
Mute
Angle
EQEQ
Enter
3
MNO
#
GotoRO/SN
SRC
Band
RDM
APSAPSAPS
PRG
STS T
RPT
TitleTitle
PBC
OSD
ID3I D3
1
2
3
4
5
PWR
R/LN/P
Language
7
CLK
AF
6
TA
PTY
1
4
GHI
7
PQRS
*
10+
Note: Remote picture just for confernce.
[PWR] Button: Power
1
[REC/Sub-T]Button: Transfer recording/Language switch
[MUTE] Button: Mute
[SRC] Button: Play source switch
Note: This unit doesn't have RDS function, AF/TA/PTY neither.
This unit doesn't have bluetooth function, []/[] neither.
8
Page 10
Basic Operation
SRC
Press [SRC] button shortly will turn the unit on.
Press [SRC] button shortly turn off.
Volume
Increasing Volume:
Press the [VOL+]button can increase the volume.
Decreasing Volume:
Press thebutton can decrease the volume[VOL- ]
MUTE
Press this button to turn off volume and again to resume.
Eject
EJECT: Press [ ] to exit the disc.
NOTE: About 10 seconds after the disc ejected, if not taken out, the disc
will be absorbed in again.
OPEN
Press [OPEN] button, the screen will turn down, press again,
it will back to originality.
Display position adjustment
Press [ADJ] button can adjust angle of screen
Pressbutton repeatedly can adjust the
[ADJ]
screen angle gradually. The unit has 3 angles for
adjustment. Each time you press the
button, the screen will move from one
angle to another angle on the same
direction. The screen angle will
move on the opposite
direction if you operate
it again.
Turn on the unit again, the
angle will back to original
setting.
CAUTION
Do not place any object on
the screen, or push it rudely.
Do not move the screen
rudely.
The movable range of the
screen may be limited to
Adjust Angle
different types of car and
install positions, etc.
:
9
Page 11
Setup Operation
SETUP
Enter the main menu, touch the setup button will display:
V d o mode:ie
BRIGHT14
COLOR
CONTRAST
MODE
Audio mode:
BASS0
TREBLE
BALANCE
FADER
EQ
Basic mode:
LOUDOFF
BEEP
CLOCK
VIDEO
AUDIO
BASIC
14
13
USER
-07
R06
R06
FLAT
ON
00:00
Menu operation
Touch []/[] to choose menu.
Touch []/[]to adjust parameter.
Touch [] to back main menu.
Menu operation
Touch []/[] to choose menu.
Touch []/[]to adjust parameter.
Touch [] to back main menu.
Menu operation
Touch []/[] to choose menu.
Touch []/[]to adjust parameter.
Touch [] to back main menu.
Vd osetupie
Bright Color Contrast.
Mode
STADUSER
BRIGSOFT
Audio setup
Audio setup Bass Treble Balance Fader
setup between 7.
+
EQ setting
NORM
FLAT
CLAS
POP
ROCK
Basic setup
Loud ON and OFF
Beep ON and OFF
Time Adjust press [] or[] button to select hour/
minute then press []or []button to setup.
10
Page 12
Radio Operation
AFTAPTY
Band Tune
Manually Tune
Press[] button: adjust to higher frequency.(such as
87.5,87.55...)
Press[] button: adjust to lower frequency(such as
105.5,105.0...)
Automatically Tune
Holding down the [] button: search higher frequency
station, and will stop when meeting one.
Holding down the [] button: search lower frequency
station, and will stop when meeting one.
Note: If the unit doesn't have RDS function, the touch-screan won't
show "AF, TA and PTY".
BAND
Press [BAND] on the screen to select among three FM or two AM
bands. (FM1-FM2-FM3-AM1-AM2)
FM1FM2
FM3
AM1AM2
Select station
Press [APS] icon
Seek Tune:
Under radio playing mode, long touch [APS] icon can seek
and store strong frequency stations automatically.
11
Page 13
Radio Operation
AF(Alternative Frequency)
Turn "AF",the unit will switch to the stronger signal of the
same station automatically.
TA(Traffic announcement)
Press TA, the unit will prior to seek the traffic information. If
the machine receives the traffic information, it will choose this
signal and quit other radio signal or CD program. If press TA
again, other program will recover and the traffic information
program will quit.
PTY(Program type)
Turn onPTY , then pressPTY and 1-6 buttons to
choose one certain program style . After this, the unit will
scan the same style programs automatically. Such as select
News programs. The unit will only scan News programs.
Note: If the unit is without RDS function, pls skip this page.
12
Page 14
Play operation
Insert DVD disc, touchscreen will show menu as follows:
T 001/003
C 002/025
DVD-V
00:33:11/01:45:44
REP
Note:
Because the different situation of Disc REC, some of the CD-R,
CD-RW,DVD-R,DVD-RW,DVD+R,DVD+RW Disc may can not bereaded.
And the Disc without final treatment can not be readed too. Regarding the
final treatment, please make conference to the guide of REC set or
REC manual.
TITLE
BACK
DVD-V
REP
00:33:11/01:45:44
OFF
1/2
OFF
BACK
TITLE
TITLE: In play mode, press [TITLE] on the screen or remote control
to back to the title menu, and re-select the items needed.
REP
Repeat mode:
When playing DVD, press [REP], you can switch on
CHAPTER/OFF/TITLE/CANCEL.
BACK
Back to Mutimedia: When playing DVD, press [BACK], it will back
to player media.
You can choose any icon to
play or setup.
Caption choose
OFF
Caption choose: If DVD contain several langrage you can switch
caption.
Note: when play DVD not have multi caption this function invalidation.
Choose angle
Choose angle: If DVD support multi angle function, touch []or
OFF
OFF
press [ANGLE] icon or remote, you can switch
different angle.
Note: when play DVD not have multi angle, this function invalidation.
Volume Control
Volume control: Touch [], can switch, between 1, have volume
1/3
1/3
and music ; 2, not have volume but have music;
3, volume and music separate.
Note: general DVD only have two mode.
13
Page 15
Play operation
Insert MP3 disc, touchscreen will show menu as follows:
MUSIC
001
001 001 MP3
002 002 MP3
003 003 MP3
004 004 MP3
005 005 MP3
Media
Back
Insert CD disc, touchscreen will show menu as follows:
MUSIC
001 CD
001 001 MP3
002 002 MP3
003 003 MP3
004 004 MP3
005 005 MP3
Back
MUSIC
NONE
FILE NAME:004 MP3
ALBUM: NONE
00:00:30/00:04:12
MUSIC
CDDA
TRACK12
00:00:30/00:04:12
PLAYING
REPEAT
PLAYING
REPEAT
BACK
BACK
Select chapter or section:
In the DVD mode,
press [ ] to choose
the last chapter; press [ ] to choose the next chapter.
REPEAT
Repeat mode:
Insert VCD disc, touchscreen will show menu as follows:
When playing DVD, press [REP], you can switch on
TRACK/OFF/FOLDER/ALL.
PBC
STEREO
BACK
REP
VCD
T 001/003
00:33:11/01:45:44
In this menu, the menu on the right side is the sub-menu.
You can press[ ][ ]tu button to select the file and items
you like.
Chapter choose: When play CD/MP3, press[ ] to choose the pre
music, press [ ] to next music.
Play/pause: Press [] button to play or pause.
PBC
PBC menu: when playing VCD, press [PBC], you can switch
between ON/OFF/CANCEL.
REP
Repeat mode: when playing VCD, press [REP], you can switch
between TRACK/OFF/ALL/CANCEL.
Track switch
Track switch: you can switch STEREO/LEFT/RIGHT by touch the
right up letter.
14
Page 16
USB/SD operation
USB/SD play opration
PLAY/PAUSE:
Press [] button to play or pause.
,
Select:
Under USB or SD play mode, press[] button to select
tracks.
USB
SD
USB/SD mode
USB/SD mode
Inset USB/SD,the play will to the USB/SD playing mode
antomaticly.
Repeat mode:
When playing, you can switch the function by touch
[REPEAT].
CHAPTER
TITLE
Note: when playing, press [BAND] to radio mode.
15
OFF
CANCEL
Page 17
Bluetooth
The Bluetooth is wireless mode of transmission in short
distance.Through Bluetooth function, the DVD unit establishes
connection with Bluetooth handset. And then, these units can
realize mutually contrdling and file transfering.
BT Choose
BT Choose:
Press [BT] or touch BT icon, can enter BT mode when calling.
Working mode of Bluetooth
Bluetooth has the following functions:
A: Paring
Make DVD Bluetooth function as handsets
facility through pairing.
B: Connecting
After connecting with the handset,
you can operate the mobile phone through DVD unit
(such as H,F, call, call record etc.)
'
Paring
Phone set pairing step as follows:
A: Turn on Bluetooth, then
touch On/Off icon to turn
on this function.
B: Turn onBluetooth
function .
C: When the mobile phone
set finds the signal, input
pairing number. Initial Pairing Code No.0000
D: After pairing, TFT screen shows pairing succeed and
quit the pairing.
NO.2
handsets
'
(NO.1)
(NO.2)
16
Page 18
Bluetooth
Mobile phone
After connected, you can make phone call through, touch
screen or phone record.
A: Making mobile phone call
After making phone call, the [ ]will shining.
B: Making touch screen call
Input the numbers on the screen, press [] icon can correct
the numbers;
Press [] icon to answer phone call;
Press[] icon to cancel or hang up.
13590201359020
Answering
Answering functions as follows:
A: After connected, the unit can use the telephone function.
B: When there is a phone call, the Bluetooth will switch to
phone function and show the calling number automatically.
C: Touch Transfer icon can
switch to phone answer mode.
Touch it again can return to
Bluetooth function of the unit.
13590201359020
Hang up
You can press the [ ]button to hang up.
13590201359020
Note: If the unit does not have this function, pls skip it.
Some models of mobile phones are not supported by the
Bluetooth module of this unit.
17
Page 19
TV tuner
TV operation
You need install TV antenna, when receive program.
TV mode:
Press [MENU] enter into main menu, then press TV icon to
enter.
TV
Channel seek:
Press [AMS] can seek TV programs and restore them
automatically.
Note: If the unit does not have this function, please skip this page.
PREV NEXT
ESC
18
Page 20
GPS Navigation
Enter Navigation
Enter Navigation menu:
Insert the SD card with map, touch [GPS] icon or press
[NAVI], enter Navigation menu, as follows:
TV
Press[] icon, it will show picture as follows, satellite
Navigation, histogram.
[]: show the satellite signal process data.
Press[]can set the Nevagation path.
[]: show satellite signal histogram.
19
Page 21
Accessories
External view
........ Numberof items
1
3
The use of any accessories except of those provided might
result in damage to the unit .Make sure only to use the
accessories shipped with the unit ,as shown above.
............
............2
1
External view
2
........ Numberof items
............1
20
Page 22
Troubleshooting
What appears to be trouble is not always serious. Please check the following points before calling a service center.
Familiar characters and their meanings
Characters
NO Disc
Bad Disc
Unkown Disc
Region Error
Causes
Disc is too dirty.
Disc is inserted upside down.
No disc in the unit.
Disc is extreme dirty.
Disc is inserted upside down.
The disc is not compatible with
the unit.
Thedisc'sregioncodeisnotthe
same as the unit's.
Remedies
Clean the disc or change the disc.
Insert the disc correctly.
Insert a disc.
Clean the disc or change the disc.
Insert the disc correctly.
Clean the disc.
Clean the disc.
21
Page 23
Troubleshooting
General problems
Symptoms
Causes
Remedies
The unit cannot be
powered on.
Remote controller does
not work.
No sound comes out or
it's hard to hear.
Poor sound quality or
sound distortion.
User preset information is
lost when ACC is off.
The fuse of the unit has been broken.
The fuse of car battery has been broken.
False operations and etc.
Battery has been exhausted.
Battery is not installed correctly.
Audio output connection is not correct.
The volume level is set to the minimum level.
The speakers have been damagedl.
The audio channel outputs are not balanced.
The speaker cord is contacted with the
bodywork.
Piraticdiscisused.
The speakers power rating does not fit into
the unit output power.
The speakers are connected incorrectly.,
The speaker cord is contacted with the
bodywork.
ACC and BATT are connected incorrectly.
Install a new fuse with correct rating.
Install a new fuse with correct rating.
Reset the unit.
Change the battery.
Install the battery correctly.
Correct the connection according to(Electrical
Connections Overall Diagram).
Adjust the volume to the optimum level.
Check the speakers.
Adjust the balance of audio channel outputs. Please
refer to (Audio control).
Use insulating cord for connection.
Use original copy disc.
Change the speakers.
Correct the connection according to(Electrical
Connections Overall Diagram).
Use insulating cord for connection.
Correct the connection according to(Electrical
Connections Overall Diagram).
22
Page 24
Troubleshooting
TFT Monitor
Symptoms
No image appears on the
monitor and warning
information is shown at
all times.
Abnormal display like
as pulsatile stripes on
the image and on.
Characters are
abnormal.
Causes
Incorrect connection of Breaking wire.
The color system of DVD disc is not
suited with the monitor.
The actual color system is not the same
as the marked color system on the label
for some piratic discs.
The video cord is broken.
The video cord is not connected correctly.
False operations.
Remedies
Correct the connection according to
(Electrical Connections Overall Diagram).
Adjust the color system of the DVD disc
or the monitor.
Use original copy disc.
Change the video cord.
Connect the video cord correctly.
Turn off the power and then turn on the
power again, or change to other playing
source and then go back.
23
Page 25
Troubleshooting
Radio Tuner
Symptoms
Causes
Remedies
It's hard to receive
stations.
Mp3 playback
Symptoms
Disc cannot be played
back.
Interruption occurred during
playback.
MP3's name cannot
be displayed correctly.
Auto antenna is not extended completely.
Auto antenna is not connected with the unit firmly.
LOCAL function is on.
Causes
Disc is scratched.
Disc is too dirty or wet.
The pickup is dirty.
Disc is inserted upside down.
Disc is scratched.
Disc is too dirty or wet.
Some contents are damaged.
Disc is not recorded correctly.
The name of Mp3 is not regular.
Correct the connection according to
(Electrical Connections Overall Diagram).
Correct the connection according to
(Electrical Connections Overall Diagram).
Close the LOCAL function.
Remedies
Change the disc.
Clean the disc.
Clean the pickup with cleaning disc.
Insert the disc correctly.
Change the disc.
Clean the disc.
Change the disc.
Record the disc again.
Use the regular characters.
24
Page 26
Troubleshooting
DVD player
Symptoms
Causes
Remedies
Disc cannot be inserted.
Disc cannot be played back.
Subtitle cannot be shown.
Audio language/subtitle
cannot be changed.
View angle cannot be
changed.
Image distortion.
PBC is invalid when playing
back VCD.
Repeat playback or GOTO search
is invalid when playing back VCD.
There is a disc in the unit already.
Disc is scratched.
Disc is too dirty or wet.
The pickup is dirty.
Disc is not compatible with the unit.
Parental lock class is too high.
Disc is inserted up side down..
The disc 's region code is not the same
as the unit 's.
There is no subtitle file in the disc.
There is only one audio language/subtitle
in the disc.
There is just one view angle in the disc.
Multi-angle view is not available for the
segment playing back now.
The disc is protected by the copyright.
The disc does not support PBC.
PBCison..
Eject the disc then insert another one.
Change the disc.
Clean the disc.
Clean the pickup with cleaning disc.
Change the disc.
Change the parental lock class.
Insert the disc correctly.
Change the disc.
Change another disc containing subtitle files.
Change another disc containing multi-language
audio or subtitle.
Change another disc containing multi-angle.
Select another segment to play back.
The unit is compatible with copy system; hence
some discs contained the informationof copying
prohibited cannot be played back.