Eonon G2201 Instruction Manual

Model:G2201
User Manual
Please read this manual before using and
save this manual for future reference
NOTES ON INSTALLATION
The unit is designed for 12V DC , negative ground operation system only.
The negative battery terminal must be disconnected before making connections, which can reduce damage to the unit due to short circuit.
Be sure to connect the color coded leads correctly according to the diagram. Incorrect connection may cause the unit to malfunction or damage the vehicle electrical system.
Be sure to connect the speaker(-) Leads to the speak(-) terminal. Never connect the left and right channel speak cables together or to the vehicle body.
After the completion of the installation and before to play (including replacing the battery), please press the RESET button on the front panel with pointed objects (Such as ball-point pen)to set the unit to initial status.
Do not block vents or radiator panels Blocking them will cause heat to build Up inside the unit and may damage it.
SPECIFICATION
General
Power Requirement 14.4DC Load Impedance 4ohm Max Power Output 60W 4 Tone Control +/-8DdB(Bass100Hz,Treble 10KHz) Dimension Approx,192 188 105mm(D W H) Mounting Dimension Approx,169 178 100mm(D W H) Weight Approx.2.15kg
DVD Deck Section
Disc Played DVD/VCD/2.0/MP3/MP4(DIVX/CD/Picture-CD) Video System PAL/AUTO/NTSC
CONTENTS
Precautions 2
Panel illustration
Main menu 5
Media player
Bluetooth 7
AV IN 8
3
6
Video Section
Video System 4:3Letter Box and 4:3Pan Scan ,16:9wide-screen Video Output level 1.0vp-p 75ohm Horizontal Resolution 500
Audio Section
Maximum Output level 2Vrms(+/-3dB) Frequency Response 20 to 20KHz Signal-to-noise Ratio 85dB Separation 80dB
AM Tuner Section
Frequency Range 522-1620(Europe/China/Russia) 530-1710(U.S.A);522-1629(Japan) IF Range 450KHz Usable Sensitivity(-20dB) 25dB
FM Tuner Section
Tuning Range 87.5-108(Europe/China);87.5-107.9(U.S.A) 76-90(Japan);65-108(Russia) IF Range 10.7MHz Usable Sensitivity 15dB Signal-to-noise Ratio 60dB Stereo Separation 30dB(1KHz) Frequency Response 30-15KHz
03.MAL.6950.001.19
Setup 9
iPod player
10
GPS operation 11
Radio operation
TV operation
20
21
Location of the Remote Control 22
Remote Control Operation 23
Installation 32
Simple Troubleshooting Guide
Wiring Diagram
35
34
Specification 36
Note: Due to continuous product improvement, specifications and design are Subject to change, without notice.
36
1
PRECAUTIONS
WIRING DIAGRAM
This unit can play the following disc only:
Type of disc Label on the disc Recorded material
Sound and moving
pictures
Sound and moving
pictures
Sound and moving
pictures
Sound and moving
pictures
Sound only
Do not attempt to modify the unit. Unauthorised modification may damage the unit.
Stop the vehicle before carrying out any operation that could Interfere with your driving.
Do not operate the unit in exteme temperatare inside the vehicle. The operating temperature of the unit is between-20 to+60
----Do not use CD with paste residue or ink on the surface
----Do not use CD with labels or Stickers attached. It cause failure Of the loader mechanism. (Shown in picture)
STANDARD CONNECT
Size of disc
GPS interface
To enjoy optimum sound and images while playing, handle the disc as follows:
----Handle the disc by its edge to keep the disc clean. Do not touch the surface.
2 35
----Clean the disc with cleaning cloth Wipe each disc from the centre out (Show in picture
Antenna Receptacle
1
Output Socket(female)
2
3
Fuse Holder(15A)
4
Video Out Receptacle
5
Output Socket(male)
6
iPod in(optional)
7
Mincrophone input
8
USB
SIMPLE TROUBLESHOO TING GUIDE
Panel illustration
Problem
No power
Some errors occur in the LCD or no function when pressing the button
Unable to receive stations
Poor effect on receiving
CDs cannot bo loaded
The stereo indicator" "is flashing
No picture
Picture distortion
Wrong region code
Cause/solution
Check the fuse. Replace with the proper value if necessary
Press the RESET button
Check and make sure the antenna is properly connected.
Antenna may not have proper length. Make sure the antenna is fully exten ded. If broken replace the antenna with a new one.
The broadcasting signal is too weak. The antenna is poorly grounded. Check and
make sure the antenna is properly grounded at its mounting location.
A CD is loaded in the mechanism.
Tune in the frequency accurately
The broadcasting signal is too weak. (Set to the MONO mode)
The video line from main unit to the TV is not connected properly .
Improper setting of the color system. Set the color system to PAL or NTSC, according to the connected television.
The CD is dirty or damaged.
Under DVD mode ,press" " on remote control pad twice, the press arrow on remote control pad, and press pad 0-6according to your region
For example, if disc region is 1, press arrow and 1 on the remote control.
Tel button
Volume button
Mode button
Reset button
Touch screen
Angle button
Remote control sensor
Eject button
Power button
GPS button
Press the station for 3 seconds to memorize preset station.
No memory on radio sation
For example, if a user wants to Preset radio frequency FM 88.10 On station 1, just simply press station 1 for 3 seconds when frequency is tuned at FM 88.10
Note:If any of the problem persist, consult your nearest service dealer.
Never attempt to disassemble the unit by yourself.
1
Tel button
When there comes a call, press it to Answer the call.(When you want to Reject or hang up the call, press" " on the front panel or HANG UP touch key in the TEL touch menu).
Volume button
2
For volume button, press( ) the button clack wise to increase the sound level and anti-clockwise to Decrease the sound level.
334
Panel illustration
INSTALLATION
Mode button
Press it to select source in the following order:
Reset butto n
Operating the unit for the first time or after replacing the car battery , you must reset the unit. Press this button with a pointed object (such as a ballpoint pen) to set the unit to initial status.
Note: When errors occur on the LCD display ,you can also press RESET button to clear the error, It will erase the clock setting and some memorized functions.
Touch scree n
Press any place on the touch screen, the corresponding touch menu will display on the screen under different Mode, pleas refer to corresponding Chapter below for operation in details.
Angle button
Press it to adjust the angle of the front panel, and there are totally four angles optional.
Eject bu tton
A. When there is no disc in the unit,
press it and the front panel will flip down to shown the disc slit in the main unit, Insert the disc into the CD slot, and the mechanism wills automatically playback the Disc.
B. When there is a disc in the unit, press it, the front panel will automatically flip down and eject the disc, if you don t take the disc away within 5 seconds, the mechanism will automatically slot in the disc, lock the front panel and select radio mode.
Power button
A. Under sleeping mode, press it to turn the unit on, and the unit will automatically select radio mode.
B. Under working mode, press and hold the button for more than 3 seconds to return the unit off.
GPS button
Press it to unter the GPS menu, press it again to return to the initial status.
Mounting Example
This mounting method is used for Japanese cars. The actual mounting method should depend on the types of the cars.
Bracket
Existing parts supplied with your car
Installing the front panel
Detaching the front panel
Notes: 1.Store small articles that are not accessible to children.
2.Install only with the supplied screws.
3.Installation varies depending on the type of cars and unit installed by qualified technician.
Be sure to press before detaching the front panel. To detach panel, press the latch shown n the left.
Remote control sensor
Sensor for the card remote commander. (For remote control version only)
Note: This window is used with remote control function. Without this function,you should ignore the operation contents about remote control function.
4
Precautions
Do not touch the front panel connection on the unit body, since this may result in poor electrical contact. If dirt or dust get on the contacts, wipe them with c clean ,dry cloth.
33
INSTALLATION
Parts List(The numbers in the list are keyed to those in the instructions.)
Main menu
32
Fasten the rear bracket screws and back side harness, and fix the unit Well.
To remove the set, pull the set out from the dash board.
Media player
Bluetooth
AV i n
USB
Setup
2,6,7,8,10 function is optional
iPod player
GPS
Radio
Back sight
TV
5
Media player
REMOTE CONTROL OPERATION
Media player
1.PLAY/PAUSE key
Press it to pause the playback, and press it again to resume to normal Playback.
3.VOL/SEL key
This key has SEL function, Repeatedly press it to select mode In the following order:
Press it to select track downward. Press and hold it for more than 3 Seconds to fast reverse the track.
5.Parameter display
After selecting the desired mode. you can adjust its level by pressing Area 5 , and the corresponding Parameter will display in this area.
Press it to select track upward, Press and hold it for more than 3 seconds to fast forward the track.
7.MORE:
Press it to display more menu.
8.MODE key
Press the button to return to main menu.
E. DIGITAL SETUP
This is for the user to set operation mode, dynamic range compression And stereo mode.
a. OP Mode
To set the operating modes for Dolby Digital decoder .
b. Dynamic Range
To set dynamic range compression
c. Dual Mono
TITLE KEY
--In DVD VCD playing mode, Press 24 (TITLE) key to show all Track title on TV screen. Press key to choose your4 Desired track number and press (ENTER) key or 2 6 ( ) key start.
Note: 1.No title display in Mp3 CD
2.To choose a desired language, Press title key.
ZOOM KEY
--In DVD VCD playing mode, press (ZOOM) key once for 25
1.5x Mode, twice for 2 x Mode. Third time for 3 x Mode, forth time for 1/2 mode, fifth time for 1/3 mode, sixth time for 1/4 mode.
Note: No ZOOM function CD/MP3 playing
. Mode.
2.MUTE key
Press it to cut off the sound output, And appears in the LCD; Press it again to cancel the MUTE function.
6
9.TA key(optional)
Traffic program/Traffic Announcement. TA function on/off.
To set the stereo mode.
31
REMOTE CONTROL OPERATION
Bluetooth function(optional)
SPDIF/PCM: When the player is connected with the 2 channels, digital stereo amplifier, please select this item when the playing disc is recorded in Dolby digital or MPEG. The analog or optical output will be modulated to 2 channels output by PCM. Note: This function is in invalid for this model.
b. Key
This is to select Treble or Bass according to your needs.
D. VIDEO SETUP
b. Contrast
c. Hue
d. Satura tion
10.RPT key
Repeat function. Press it to repeat the current track/chapter; Press it Again to repeat the title; Press it The third time to repeat all; Press it The fourth time to cancel the repeat function.
11. RDM key
Press it to play the disc in random, Press is again to resume normal Playback.
12. OSD
OSD information display.
13. L/R key
Press it to get switch R+R/L+L /STEREO.
14. N/P key
Press it to switch video system:
Bluetooth
Bluetooth pairing setting:
a)Bluetooth active is the default setting for the player.
b)To pair the player with mobile, operate mobile: Activate Bluetooth and star a device search. Select the Bluetooth device in the player and Press Pair .
C)Operate mobile and input the default password 0000 .
This is for the user to set Brightness, Contrast, Hue and Saturation of the picture by pressing the arrow left/ right button.
a. Brightness
30
e. Sharpness
Press (ENTER key) to confirm the change.
NOTE: Only on TV/AV mode ,the Video setup is available.
15. MENU
Press it to switch to menu, and dvd Will enter title menu and display all Titles for dvd disc and you can Choose your desired you can Track by pressing direction button.
16. Direction keys
Press direction keys( ) To select your desired title or track.
17. OK
Press it to confirm.
D)After the pairing is successfully Connected, SUCCESS will display on the LCD and you can make call through the player.
Make call through the player:
1.Number keys: Input the phone number you want to call.
2.Cut off: When you input the incorrect character, press it to delete the Incorrect character.
7
AV IN
REMOTE CONTROL OPERATION
3.Connect: To pair mobile with the player. Bluetooth can be switched On or Off by press ing this button After The pairing is connected.
4. After you input the phone number, press it to make a call. When there is an incoming call, press it to answer the call.(The button in the front panel has the same function and operated as the same way.
5. When there is an incoming call, press it to reject or to end the call.
Exit the touch menu.
7.Status bar Display status of the connection or phone number.
AV IN
3. In AV IN mode, all the touch keys keep the same functions and operate in the same way as other modes. For details of this operation, please see main section in Media player chapter.
Note: The unit can t be directly
Connected with high power AUX source, in order to aviod fire or other damage to the
unit.
4.Press SYS key to switch the video system:
USB Player
The unit can be connected to a USB device for playing MP3/MP4/JPG files through the USB cable. All the touch keys keep the same functions and operate in the same way as other modes, For details of this operation, please see main section in Media player chapter.
g. Default
B. LANGUAGE SETUP
Select the preferred OSD Language, Audio Language, Subtitle language and Menu Language by using the.
ARROW keys.
a. OSD Language
c. SUB TITLE Language
d. MENU Language
C. AUDIO SETUP
SPDIF/OOF: Analog or optical output port has no output signal at all.
a. AUDIO Out
AV IN OPERATION
1.Press MODE key to switch to AV IN mode.
2.Connect to AV IN source.
b. AUDIO Language
This is to activate the audio output from SPDIF/OFF mode to SPDIF/ RAW mode or SPDIE/PCM mode. SPDIF/RAW: When the player is connected with the power amplifier by the analog or optical port, please select this Item when the playing disc is recorded In Dolby Digital, DTS or MPEG. The power amplifier you connected must
have decode function for Dobly Digital,
DTS or MPEG.
298
REMOTE CONTROL OPERATION
Setup
a. TV Typ e
1. 4:3 PS Played bask in the PAN& SCAN style.(If connected to wide-screen TV, the left and right edgesare cut off)
2. 4:3 LB Played back in LETTERBOX style. (If connected to wide-screen TV , black bands appear at top and bottom of the screen)
3.16:9 Select when a wide-screen TV set Is connected.
e. Password
f. Rating
Select suitable guidance rating by the cursor button and confirmed by Pressing ENTER key)6
Rating 1:[KID SAFE] Select this when the program are safe for all kids to view.
Rating 2:[G] Select this that allows admission to all Ages.
Rating 3:[PG] Select this that needs parental guiding.
Setup
1. Basic setup
(1) RADIO Select radio frequency according to The following sequence:
(4)CLK Clock display on/off, the current Time display on LCD when CLK ON.
(5)BEEP Keypad tones setting on/off.
2.Video setup
(1) Brightness adjustment
Enter the password and press ENTER button. Type the old password (The initial factory code is 0000) and key in 4 characters password now you want to use, and type again to confirm.
Rating 4:[PG13] Select this when children under 13 are forbidden to view.
Rating 5 :[PG-R] Select this when PG-R was printed On the DVD disc.
Rating 6:[R] Select this when children under 17 must be guided by their parents.
Rating 7:[nc-17] Select this when children under 17 are forbidden to view.
Rating 8:[ADULT] Select this only allows admission to all Adults.
(2) TV system switch: Press it to switch the tv video system:
Note :the player will memorize the Tv system setting when the player is off.
(3)TIME Time adjustment
(2) Color Adjustment
(3) Contrast adjustment
(4)Video mode Press it to switch video mode According to the following sequence:
928
ipod player(optional)
REMOTE CONTROL OPERATION
3.Audio setup
(1)BAS BASS adjustment
(2)TRE Treble adjustment
(3)BAL Balance adjustment
(4)FAD Fade adjustment
(5)LOUD Loudness
(6)EQ Press it t select the desired EQ effect in the following order:
4.Direction keys Press direction keys to select your desired menu or location.
ipod player
1. - + Volume adjustment. +:volume level increase
-:volume level decrease
2.MENU Press menu to control the functions of the iPod.
3.OK Press it to confirm.
Press it to select track downward/ upward. Press and hold it for more than 3 seconds to fast reverse/fast forward the track.
5.UP DOWN
Press them to select your desired title or track.
SETUPKEY
1.Press 23 ( SETUP KEY) of remote Control in the stop mode. (Press the 20 STOP key twice to ensure the Player is under STOP mode.)
2.The main page of setup menu is dis­ Played.
3.Select the preferred item by using the (ARROW keys).4
4.Press (ENTER key. 6 A .System Setup This setup page includes all items of TV system, Screen saver , TV type,
passward ,Rating & Default features. For detail please refer to SYSTEM
SETUP MENU. B. Language setup This setup page includes all items of OSD language features. For details Please refer to LANGUAGE SETUP MENU. C. Audio Setup This setup page includes all items
for AUDIO. Please refer to AUDIO
SETUP MENU. D. SYSTEM SETUP This setup page includes all items
for VIDEO. Please refer to VIDEO
SETUP MENU.
This player can play disc recorded In either PAL or NTSC format. Select NTSC format when you connect To NTSC TV. Select PAL format when You connect to PAL TV. Select the Format (PAL/NTSC) according to you TV system.
b. Auto Play
Select the SCREEN SAVER Output ON/OFF .
C.Video
5.Back Exit setup menu.
Play/Pause.
7.Back Return to main menu
A. SYSTEM SETUP A. TV System.
Note : This function is invalid for this model
2710
REMOTE CONTROL OPERATION
Setting CD Playback Time
--In VCD CD mode, press 18 (GOTO) key and set the time when you begin to play the track, and the television will display the time --:--. Enter your desired time by pressing number button 14 (0~10+).For example, enter: 25:00, and press (ENTER) to6
confirm. It will automatically start
playing the track from the point of twenty-fifth minutes in the disc.
--In DVD playing mode, press 18 (GOTO) key once and input a desired track number, Then press (ENTER) key to play the DVD 6 from the position corresponding to the track number selected.
--In DVD playback mode, press 18 (GOTO) key once and input a Desired time to play the DVD from the position corresponding to the time selected. For example, press (GOTO) key once and the 18 television will display the time--:--:-­ Enter your desired time by pressing number button (0~10+). And 14 4 direction button, Then press 6 (ENTER) button, it will automatically start playing the track trom the point of your desired time in the disc.
Note: No time play function for Mp3
.
Stop the Playback
--In DVD mode, press 20 button to suspend the playback and press Play to continue. Press it again to stop the playback.
MULTI-ANGLE KEY
--In DVD playing mode, press (ANGLE key to watch the DVD Content from different angle.
SLOW KEY
--In DVD/VCD playback mode, press (SLOW) key once for / slow, twice22 for 1/3 slow, thrice for 1/3 slow, and so on. When the key is pressed the seventh time, it will return to normal Playback.
Note : Not applicable in Mp3 and CD playback.
21
GPS Operation
GPS Operation
Safety Notices and Warnings
Global Positioning System(GPS is operates and controlled under the sole responsibility of the Government of the United States of America, who are responsible for its availability and accuracy. Any change in GPS availability and accuracy, or in environmental conditions, may impact the operation of your Navistar.
Use this product prudently. The product is to be used only as a navigation aid. It is not for precise measurement of direction, distance, location or topography.
When the artificial satellite carrying out GPS first fixes position, stay in thesame place please, use more spacious that place is suitable , superjacent
have not to blocking anything. Need to look at environment that time and artificial satellite signal intensity but fix above waiting for the ten minutes.
For your own safety, do not operate the controls of the product while driving.
GPS satellite signals can not pass through solid materials(except glass).When you are inside in a tunnel or building, GPS positioning is not available. Signal reception can be affected by situation such as bad weather or dense overhead obstacles (e.g. trees and buildings)
The wireless devices might interfere the reception of satellite signal and cause the reception of the signal to be unstable.
When you get off the car, do not leave your device on the dashboard or the car glass that is subject sunlight. The overheating of the battery can cause malfunction and/or danger.
Mode Switch
--Press (MODE) button to Switch to radio mode or playback Mode.
19
The windshield receives paste the paper which be used for adiabatic or preventing explosion, will disturbed the signal quality. For better signal reception, it is recommended that you can choose adiabatic paper of not containing metal matter or use a car antenna(option).
The calculated route is for references only. It is user's responsibility to follow the traffic signs and local regulations along the roads.
1126
GPS Operation
Chapter 1.System Set Up
Press Config Icon on the main menu and then enter into the system Set-up interface.
REMOTE CONTROL OPERATION
--During CD MP3 VCD mode, Press 15 (RPT) to repeat the current track being played. Press it again to cancel the repeating function.
Left/Right/Stereo Selector
--During playback mode, continuously press 15 (AUDIO) can change the sound to left/right speaker or stereo mode.
The system menu provides the Volume , Backlight , NaviSetting
Calibrate , Language , GPSTest , and Return for choose, the
introduction are in the following chapters.
1.1.Volume
Examine or set up the system's volume.
1)Press the Config Icon on the main menu and then enter into the system Set-up functions.
2)Press the volume Icon on the set up menu.
Note: In VCD MP3 CD mode. The Initial setting is repeat playing All the tracks. Note :In radio mode, press 12
(AMS/RPT)to scan each stored
Station for 10 seconds.
Random Playing
-- During playback mode, press 13 (RDM) button
to play any track at
Random.
Number Buttons
-- During radio , you can select one of the 6 stored stations on each band by pressing any one of the number button .14
--During the playing mode, you can select any track directly by using number button (0~10+). 14 for example, if you need the fifteenth track, you can first press button 10+ and then press button 5, the corresponding track (15) will be Played.
Note: When button 10+ is first pressed, it works
as 10+ , it works as 20+ when pressed at
the second time, the third...30+....and so
on and so forth. In PBC playback mode, number button is not functional.
Note: There are 5 different surrounding Effect in surround mode. During VCD mode, you can see the different Pictures indicating different effects On the television.
Playing PBC (menu)
--During VCD mode only, when pressing 16 (PBC) button at the first time, PBC playback starts and the menu of entire disc appears on the television. And then you can select your favourite track by using number button 14 (0~10). When a track is playing ,you can press 20 (STOP/RETURN) button to return to the menu if you want to stop to select other tracks. To cancel PBC playing, press 16 (PBC) button again.
Subtitle Selector
--During DVD mode, press 17 (SUB-T) button to switch the menu to Chinese or English.
2512
REMOTE CONTROL OPERATION
Volume Increasing/Decreasing
--Press 7 (VOL+or VOL-) button to increase or decrease the volume level respectively .
Tuning/Selecting Tracks
/Fast Rewind/Forward
--During radio mode, continuously press 8 ( or ) button to manual search a station downward or upward respectively; if press and hold 8 ( ) button for more than 3 seconds, the radio will Automatically search a station downward or upward respectively until it finds a station.
--During playback mode, press and hold 8 ( ) button to fast rewind or fast forward to reach your desired track quickly. momentarily pressing ) button, you can select your desired track downward or upward Respectively.
8
8
or
8
or
8
( 8
or
On-Screa Display During CD VCD DVD mode, press 10 (OSD ) button. The display shows single track elapsed time ,single track remaining or entire disc remaining, and the track being played and the content of the whole disc .
Note :During Mp3 mode, only single track elapsed time is displayed in OSD mode.
VOL/BAS/TRE/BAL/FED Selector Repeatedly press 11 (SEL) button to select the desired mode in the following order:
Note: selecting your desired mode, you can adjust the current mode being displayed by using (VOL+or VOL-) buttons. When P-EQ made is activate, press SEL button to select the modes. And Bass/Treble Mode are invalid (Show as below)
GPS Operation
3) You can select the left or the right button to adjust the volume. button use
to adjust the volume slightly, button use to adjusts the volume loudly .
4)Click can choose mute click sound.
5)Press to save the setting and press exit.
1.2.Backlight
1)Press the Config Icon on the main menu and then enter into the system Set-up functions.
2)Press the Backlight Icon on the set up menu.
Press to darken the screen, press to lighten the screen, press to save the setting and press exit.
1.3.Navisetting
1)Press the Config Icon on the main menu and then enter into the system Set-up functions.
2)Press the NaviSetting Icon on the set up menu.
Program Playing
--During CD VCD mode ,you can set the program order to play. You can follow the steps below: first, press 16 (PBC) button, and then press 9 (PGM) button, and
the television displays
programming P00:00. You can set
the program order to play by pressing
14 2 (0~10+)button, and then press
toPlay.
Note: program doesn t function
when playingMP3.
Repeat Playing /AMS
During DVD mode, first, press 12
(AMS/RPT) to repeat the current
track being played; Press it again to repeat playing All the tracks. Pressing it the third time will cancel the repeating function. (LCD will display different designs)
3)Click can auto run navigator application with start. Press
button can enter the interface of the way choice.
1324
GPS Operation
4)This interface show all the Folders and execution files. You can copy the different maps to the SD card and select the path which you choose, and then press to make sure. Press and can preview page and next page. Press exit.
5)Under the NaviSetting interface, press to save the setting.
PS: This production up to maps as Route66 Horizon PaPaGO Gate5 etc.
1.4.Calibrate
1)Press the Config Icon on the main menu and then enter into the system Set-up functions.
2)Press the Calibrate Icon enter the calibration program.
3)According the system prompt click the screen exactly. If you want to exit, press the Return button on the device.
1.5.Language
1)Press the Config Icon on the main menu and then enter into the system Set-up functions.
2)Press the Icon enter the Language setting interface.Language
In this menu, can transform the system language into English, traditional Chinese as well as simplified Chinese. Setting complete, press to save the setting and press exit.
1.6.GPS Test
REMOTE CONTROL OPERATION
Replacing the Battery
When the range of the operation of the card remote control becomes short or no function with a new button cell.
1.Pull out the Battery Holder while Pressing the Stopper .
2.Put the button-type battery(+) mark upward into the Battery Holder.
3.Insert the Battery Holder into the Remote Control.
Power Button
-- Press ( ) button to turn1 On/Off the power.
Pause/Play Button
-- Press ( ) button to suspend2 The playback of CD MP3 VCD DVD. Press it again to return to Normal playback mode.
Mute Button
-- Press ) button to cut off 3 ( the sound output, Press it again to resume at the previous sound Level.
Menu Button
-- Press 4 to select Your desired menu. Then press 6 (ENTER) or press the play Button 2 ( ) to confirm.
Note: This function works in main menu mode only.
Band/System Switch
You can know the secondary planet and the orientation from this interface. Click
can exit.
You can know the secondary planet and the orientation from this interface. Click can exit.
Note: Some models are not equipped with remote control. you should ignore The contents about remote control.
-- During radio mode, press 5 (BAND/SYS) to switch receiving Band. Press and hold it, open the LOUD function.
-- During playback mode, press 5 (BAND/SYS) button to swich to AUTO PAL or NTSC system, Press and hold it to open the LOUD function.
2314
LOCATION OF THE REMOTE CONTROL
Insulator
Please take off the insulator
Before using the remote.
1 Power Switch 2 Pause/Play Button
Mute Button3
Selecting Menu Button
4
Band/System Switch
5
6
Enter Button
Volume control
7
Tuning/Selecting
8
Tracks/F.F/REW
Program Playing
9
On-Screen Display
10
11 Setting the Sound
Characteristics
Repeat Playing
12
13 Random Playing
14 Number Button
15 Audio-setting
16 PBC Menu
17 Subtitle-Setting
18 Playing Time-Setting
19 Mode Switch
20 Stop/Reverse Button
21 Angle-Setting
22 Slow-motion Play
23 Setup Menu
24 Menu-Display
25 Zoom-Setting
GPS Operation
Chapter 2.MP3
This chapter introduced how to uses Audio player.
2.1.Audio player program
1. Select the MP3 icon on the main menu.
2. The program use as MP3 player. The function characteristic includes:
Play the Audio file/files. Basic control: play, pause, next song, previous song Order play and circle play Press the list icon and then enter the playlist
3. Press leave the player's interface but still play music in
other interface. Press will leave the Audio player program.
2.2.Prepare your Audio file
Before you use the Audio player program, you must prepare a SD card to store your Audio file/files, Insert the SD card into the slot. When you turn on the program, system may automatic sense the Audio file/files.
2.3.Play music
1. Select the MP3 icon on the main menu then enter the program.
2. Press ,start playing. Other button's functions show in the following introduction.
3. The file sensed by the program will become a playlist.
This program support the format of MP3 WMA and WAV, etc.
1522
GPS Operation
2.4.Play control
MP3 program can controlled by buttons. Their functions see in table1.
Button
2.5.Manage the playlist
If you want to set up your own play list, please according to the process as below. Edit the list
1.Start up the Audio player program then click icon
Name
Play
Previous song
Next song
Mute
Volume reduction
Volume increase
Circle play
Order play
playlist
Return
close
table1
Introduction
Play
Play the previous song in the list
Play the next song in the list
Mute
Volume reduction
Volume increase
circle play file
Order play file
Open playlist
Leave player interface but program is not close
Close Audio player program
TV OPERATION(optional)
TV OPERATION10
1.SEEK key
Press it, the unit will search automatically form VHF. When all the 100 channels are searched and stored or when the search is completed, auto-search will stop. After the auto-search is finished, the unit will select the first channel as default.
2.MUTE key
Press it to cut off the sound output, and will appear in the LCD.
Press it again to cancel the MUTE Function.
3.VOL/SEL key
This key has SEL function , Repeatedly press it to select mode
5.Parameter display
After selecting the desired mode, Y ou can adjust its level by pressing Area , and the corresponding5 parameter will display in this area.
6. Select the downward channel to watch.
7. Select the upward channel to watch.
8.MODE key
Exit the TV mode and return to main menu.
4.TA key (optional)
For details, please see Media Player
chapter.
2116
RADIO OPERATION
GPS Operation
Press it to tune a station downward.Press and hold it for more than 3 seconds , the radio will automatically search a station downward and play when it finds a Station. You can store the station by pressing the desired number control or the desired stationIn area
12
Press it to tune a station upward. Press and hold it for more than 3 Seconds, the radio will automatically Search a station upward and play when it finds a station. You can store The station by pressing the desired Number key in the remote control or The desired station in area
12 . .
7.Band Selector
Press ir to select bands in the Following order:
8. Mute Button
Press button to cut off the sound output. Press it again to resume at the previous sound level.
9.ESC
Exit radio menu and retun to main menu
9 Back sight Press it to enter back sight mode, And LCD will display rear view.
2.You can use these three buttons to edit the playlist: .Under the file list, press
selected.
3.Click
This chapter introduced how to use video player.
3.1.Video player program
1. Select the MP4 icon on the main menu.
2. Video player program use as MP4 player. The function characteristic includes:
Play the video file/files. Basic control: play, pause, next song, previous song Order play and circle play Press the list icon and then enter the playlist
3. Press will leave the video player program.
3.2.Prepare your video file
Before you use the video player program, you must prepare a SD card to store your video file/files, Insert the SD card into the slot. When you turn on the program, system may automatic sense the video file/files.
3.3.Play video file
1. Select the MP4 icon on the main menu then enter the program.
2. Press , start playing. Other button's functions show in following introduction.
3. The file sensed by the program will become a playlist.
4. Press will leave the video player program. This program support the format of MP4 WMA and WAV, etc.
can return the player interface.
Chapter 3.MP4
can play the songs which you
1720
GPS Operation
RADIO OPERATION
3.4.Play control
Video player program can controlled by buttons. Their functions see in table2.
button
Annotate click screen can enter full screen
3.5.Manage the playlist
If you want to browse playlist or choose the video file, please according to the process as below.
1.Start up the video player program then click icon, then enter the interface as below.
name
play/pause
stop
Decrease the volume
Increase the volume
playlist
mute
close
Table 2
introduction
play/pause
stop
Decrease the volume, appear
the volume pointer
Increase the volume, appear the volume pointer
Open playlist
mute
Close video player program
Radio(RDS is optional)
1.AF key Alternative frequency tracking, The radio automatically selects the alternative frequency of the same programme with the reception. When AF is on, AF in the LCD With be flashing, when AF is off,
AF in the LCD disappear.
3.PTY key Press PTY key to select program type:
Press touch area 12 to select
programme Contents as follows:
(A) PTY MUSIC group:
1. POP M, ROCK M.
2. EASY M, LIGHT M.
3. CLASSICS, OTHER M.
4.JAZZ, COUNTRY .
5. NATION M, OLDIES.
6. FOLK M.
(B) PTY SPEECH group:
1.NEWS, AFFAIRS, INFO.
2. SPORT, EDUCATE, DRAMA.
3. CULTURE, SCIENCE, VARIED.
4.WEATHER, FINANCE, CHILDREN.
5. SOCIAL, RELIGION, PHONE IN.
6. TRAVEL, LEISURE, DOCUMENT. The radio will start searching corresponding PTY information and Is stops when the inf ormation isfound. if there are no PTY information, it automatically switches to normal mode.
4. APS key.
2.You can use these three buttons to edit the playlist: .Under the file list, press
selected.
3.Click
can return the player interface.
can play the songs which you
2.TA key Traffic program/Traffivc Announcement. When TA is on, TA in the LCD will display and will appear TASEEK .10 After TA information os searched,
10 will display the corresponding
Frequency. If no TA information is searched, NO Ta will display in the LCD and it automatically switches to normal mode.
Pres it to start automatic scanning of radio stations .The unit will automa-
-tically pick up the station and store in to area . A total of 18 FM stations 12 and 12 AM stations will be stored. After all the stations are stored station. The unit will start playing the first station stored till the last station stored
1918
Loading...