Thank you for buying this product, please read through these operating instructions,
so you will know how to operate your model properly. After you have finished reading
the instructions, put them away in a safe place for future reference .
CONTENTS
PRECAUTIONS
FRONT PANEL
TOUCHING CONTROL OPERATION
REMOTE CONTROL
BASIC OPERATION
RADIO OPERATION
BLUETOOTH OPERATION
TV OPERATION
2
4
6
15
19
20
23
26
DVD/VCD/CD OPERATION27
SYSTEM SETUP
MP3 OPERATION
INSTALLATION
TROUBLE SHOOTING
CABLE CONNECTION
ACCESSORIES
30
35
37
39
41
41
SPECIFICATION
IMPORTANT: Please adjust screen to make the touching effect function best when
you initiate the unit for the first time.
For the details, please refer to the operation at Page 14.
NOTE: Due to the continuous product improvement, specifications and design are
subject to change without prior notice.
42
1
Page 4
PRECAUTIONS
1. Be sure to connect the color coded leads according to the diagram. Incorrect connections may cause the unit to malfunction or damage the vehicles electrical system.
2. Be sure to connect the speaker (-) leads to the speaker (-) terminal. Never connect
the left and right channel speaker cables each other or to the vehicle body.
3.Make sure all the connections are completely correct before turning on your unit.
4. When replacing the fuse(s), the replacement must be of the same amperage as shown
on the fuse holder.
5. Do not block vents or radiator panels. Heat may be caused inside and some accident
may be resulted by fire.
6 After completing the installation and beginning to play the unit (including replacing the
battery),please press RESET button on the front panel with pointed object (such as ballpoint pen) to set the unit to initial status.
7.Keep hands, finger, or any other object away from the back of the front panel or gaps of
the base top (shown as picture) when closing or opening to avoid damage or injury.
Replacing the Fuse
Make sure the amperage matches the specified value when replacing the fuses. If the
fuse is blown, check the power connection and replace with a new one. If the same
problem occurs, it would be subjected to the malfunction in-house.In such cases, please
consult the nearest service dealer.
WARNING:
Never use the fuse with the rated amperage more than that supplied to your unit, other wise the unit will be damaged .
2
Page 5
PRECAUTIONS
This unit can play the following discs only:
F
Type of disc
DVD
VCD
Label on the disc
TM
VIDEO
Recorded material
Sound and moving
pictures
Sound and moving
pictures
Size of disc
12cm
12cm
CD
MP3
NOTE: The unit is compatible with VCD1.0/2.0/3.0 version and DVCD disc.
Sound only
Sound only
12cm
12cm
*Do not attempt to modify the unit, modifying the unit may cause an accident.
*Stop the vehicle before carrying out any operation that could interfere with your driving.
*Do not work in extremely high or low temperature. Be sure the temperature inside the
vehicle is between +60 C and -10 C before turning on your unit .
*To enjoy optimum sound and images while playing, handle the discs as follows:
Handle the disc by its edge to keep the disc clean, and do not touch the surface.
Do not use your CDs with paste residue or ink attached.
Do not use CDs with labels or stickers attached, which may leave a sticky residue
while beginning to peel off. (Shown as the picture)
Clean the discs with an optional cleaning cloth. Wipe each disc from the center out.
(Shown as the picture)
3
Page 6
FRONT PANEL
MUTEMUTE
SEL SEL
12
SRCSRC
BAND/BAND/
MICMIC
7
2
1
4
3
5
6
8 9
10
11
13
14
4
Page 7
FRONT PANEL
1.AUX IN
Connect the audio cable to the unit then you can enjoy the music.
2. PWR/MUTE
Press the button to turn on the unit and press and hold the button to turn off the unit.
In power on, press to shut off the sound output and press it again to resume previous sound.
3. >>I/I<<
In radio mode, press to manual seek a station. Long press to automatic seek a station.
In playback mode, long press to select fast forward or fast backward. Press to select last
or next track(chapter)
4. RESET
5. SEL +/-
Press + button to increase the volume level and press - button to decrease the volume level.
Press the button to select one of the control items: L-front/ R-front/L-rear/R-rear/Subwoof
/Bass/Middle/Treble/Angle/Volume
6.SRC
P
ress the button repeatedly to switch sources.
7.MIC
8.BAND/ >II
In radio mode, press the button to select among three FM and two MW bands.
In play mode, press this button to pause or resume playback.
9.
Press to open/close the front panel. During opening the front panel, you can press
the button to set the panel angle.
10. IR WINDOW
11 USB SLOT
.
12.TFT DISPLAY
13.
Press to eject a disc.
14. SD slot
Insert the SD card, the unit will play the items automatically.
, then press +/- to adjust each item.
Note:
Once the SD card could not eject auto-matically after pressing, just take it out manually.
5
Page 8
MENU SYSTEM
The users can perform operation by touching screen directly.
Radio Operation
1
2
3
4
5
Page1
6
7
8
9
10
1. HALF LIGHT MODE
Turn on /off the backlight.
(The function can be used to change the screen brightness while traveling at night)
2. SOURCE
To display the SOURCE screen
3.Station preset button
To display the preset station list
(touch one of the station preset button to recall the radio which stored on the position;
long touch to save the current frequency into the station)
4.BAND
To switch bands.
5.LOC
To select strong or weak stations reception
6.EQ
To select a preset equalizer mode.
7.LOUD
To switch LOUD control function on/off
8.PAGE 1
To switch to RDS operation page.(Refer to RDS Opetation for detail)
9.SEEK-/SEEK+
To seek a station automatically.
To seek a station manually(long touch).
10.AMS
To browse preset stations.
To search and store stations automatically(long touch).
6
Page 9
RDS Operation
1.TA
1
2
3
EON:OFF REG:OFF
PTY:NONE
RT:
TAAF
PTY
Seek-
87.50MHz
PS:
PTY:
Seek+
Page2
4
5
To turn on /off TA function
2.AF
To turn on /off AF function
3.PTY
To switch RDS program type
4.Page2
To switch to radio operation page.
5.SEEK-/SEEK+
To seek a station automatically.
To seek a station manually(long touch).
EON(Enhanced Other Networks)
ON: Active the EON function, the receiver automatically tunes in the station that broadcasts
the traffic information when it occurs. After broadcasted ,the unit will automatically return
to the original source play except the traffic information broadcasting.
OFF: De-active the EON function
REG(Regional)
ON: Active the REG function, the unit automatically keeps receiving the related RDS
station.
OFF: Deactive the REG function
Multi-- Player Operation
In DVD mode, the touching screen displays as following after touching at random position.
PAUSE
PREV
PLAY
1
2
3
STOP
NEXT
MENU
4
5
7
Page 10
1.PLAY
To start the playback.
2.PAUSE
To pause the playback.
3.STOP
To stop playing, touch twice to stop
completely.
4.MENU
To display the DVD SETUP screen.
5.PREV/NEXT
To select previous/next chapter or track.
NOTE:Touching the left middle position twice to display the TITLE MENU selection screen,
touching the right middle position twice to display the ROOT MENU selection screen, touching
the right top position to display the number keyboard. You can select chapter(track) by
pressing the touchable screen or the RC.
Bluetooth Operation
Hands-free phone Operation
1
2
3
4
5
1. MENU
To display the Bluetooth main screen.
2. PHONE BOOK
To display the phone book screen.
3. SETUP
To display the Bluetooth s tup screen.
e
4. SOURCE
To display the source selection screen.
5.dial number list
6. DIALLING
To dial a call.
7. CLEAR
To clear the inputted telephone number.
8. HANGING
To hang up a call.
9. AUDIO TRANSFER
To transfer calling audio output mode.
8
6
7
8
9
7
Page 11
The phone book screen
4
1
2
3
1.
To display a telephone number list of the received calls
2.
To display a telephone number list of the
dialed calls
3.
To display a telephone number list of the received but you missed
4. >>
To change the list page
The Bluetooth Setup screen
1. LINK
1
2
5
3
4
6
7
8
To connect the Bluetooth device.
2. PAIR
To pair up the Bluetooth device.
3. DISCON
To disconnect the Bluetooth device
4. RESET
To reset the unit if there is something wrong with the Bluetooth function.
5. >II
Playback/pause
6.
To stop playback
7. I<< / >>I
To find the begin of the last or next track
8. < / >
To adjust the volume
The touching buttons (from5 to 7) are available if the A2PD function is activated.
8
9
Page 12
Setup Operation
TOUCH ON THE TOP LEFT POSITION TO ENTER SOURCE INTERFACE.
The unit will return to the previous mode if no operation is performed in 5 seconds.
Disp
Menu
1
2
3
Audio Video
SYS
Exit
6
5
4
1.Menu
To display the source selection screen.
Menu
Disp
Audio Video
SYS
Exit
Touch the item to select source displayed on the unit screen.
2. Disp
To display the relative information.
HH:MM:SS
NOW:RADIO
DRIVE:DISC
It is unavailable in AUX or TV mode.
*
* If another monitor(rear)is connected to the unit,image/audio of the rear
monitor can be changed from the unit,so you can enjoy separate image/audio
in the rear seats.
* The unit will output corresponding source sound through REAR-VIDEO-OUT
or DUAL-AUDIO-OUT.
10
9
Page 13
TOUCHING CONTROL OPERATION
3.Audio
Touch on the AUDIO button and the screen will display as following:
Volume
L-front
R-front
Video
SYS
SYS
Exit
Exit
Menu Disp Audio Video
In this menu, there are items of Volume, L-front,R-fornt, L-rear, R-rear , Subwoof, Bass,
Middle and Treble can be adjusted. Touch on the button to adjust each item and
touch on button to turn pages and select the item listed above.
4.Video
Press on the VIDEO button and the screen will display as following:
Bright
HUE
Contrast
Sharp
Disp
Menu
Audio
In this menu, there are items of Bright, Hue, Contrast, Sharp can be adjusted.
Touch on the item that needs adjusted then touch on the button to adjust.
5.SYSTEM
To display the system setup screen. Refer to system setup operation for detail
6.EXIT
To return to current source screen.
10
11
Page 14
SYSTEM SETUP OPERATION
Clock Sys
Key Beep
Local Area
Menu
Disp
Audio
Video
SYS
Clock Sys
Set the time display mode(12H/24H)
Key Beep
Turn on/off the sound guide function
ON:activate the sound guide mode
OFF:deactivate the sound guide mode.
The sound guide beep will not be produced when a button on the unit is pressed.
Local Area
Touch the provided option to change the radio frequency for different country.
Bass freq
Middle freq
Treble freq
Menu
Disp
Audio Video
Touch the provided option to adjust the bass freq, middle freq, treble freq.
Exit
SYS
Exit
Switch page button
12
11
Page 15
Subwoof freq
BassQ factor
MidQ factor
Menu Disp Audio Video
Exit
SYS
Touch the provided option to change the sub woof ,the bass and middle quality factor.
Back Bright
Back light
Disp Audio Video
Menu
SYS
Exit
Back Bright(dimmer)
The function to adjust the brightness of the backlighting for easier viewing.
(Normal status's 20%,40%,60%,80% )
Back light
The function to set the backlighting duration.(normal status's off,15s,30s,60s)
12
13
Page 16
Clock Adjust
Touch Adjust
Exit
Menu
Disp
Audio
Video
SYS
Clock Adjust
Adjust the time by touch
To select the desired item then set up (hour, minute, second)
To change the display number
Touch Adjust
When the display position on the screen and the touch position on the touch panel do not
match, or using the product at first time, the adjustment becomes necessary.
X < - press it
Accurately touch the X mark provided in the screen for more than 2 seconds until the
Slide the tray out on the back of the remote control and insert the battery with the plus
(+)and minus(-)poles pointing in the proper direction.
Use and care of the remote control
Point the remote control in the direction of the front panel to operate to use it.
Notes:
Using batteries improperly can cause them to explode. Take note of the following points:
* Keep the battery out of the reach of children. Should the battery be swallowed,
immediately consult a doctor.
* Use one CR2025(3V)lithium battery.
* Remove the battery if the remote control is not to be used for a month or longer.
* Do not short-circuit, disassemble or heat batteries.
* Do not dispose of batteries into fire or flames.
* Dispose of spent batteries properly.
* Do not let the remote control fall onto the floor, where it may become jammed under the
brake or accelerator pedals.
16
15
Page 19
REMOTE CONTROL
1. POWER/
Press the button to turn on the unit; Press and hold for 1 second or longer to turn off the
unit. In power on, p
2. EQ/
Press to select the corresponding preset modes to adjust the sound quality.
In bluetooth mode, press this button to dial up a call.
3. ANGLE/AMS
Press to change the viewing angle in DVD mode;
stored station. Long press to scan and store station automatically.
In TV mode, long press the button to scan and store channel automatically, press it again
to stop scanning.
4. SUB-T/LOC
In DVD playback mode, press to change the subtitle language; In radio mode, press to
select strong or weak station reception.
5. PROG/A-B
In DVD/VCD/CD mode, press to set the program order to play; In mode, press
and hold to play the section of selected chapter/track repeatedly .
6. OSD/
In playback mode, press to display the playback information;
display the current time, the set source output through the front and rear display, the
current available drive.(Disc/SD/USB);In bluetooth mode, press to function as button
on your mobile phone functions .
7. GOTO/ #
In DVD mode, press the button and the cursor button to select TITLE, CHAPTER,
AUDIO, SUBTITLE, ANGLE, TT TIME, CH TIME,
ENTER button to set the value.
In VCD mode, press GOTO button and cursor button to select TRACK DISC TIME
TRACK TIME REPEAT TIME DISP.Then press ENTER button to set.
In CD/MP3 mode, press GOTO button to select "Disc Go To:_ _ _", "Track Go To _:_ _:_ _",
"Select Track:_ _:xx". Then press 0-9 number buttons to set the track you want.
In bluetooth mode, press this button to function as # button on your mobile phone
functions .
In radio mode ,press the button and the number button to set the frequency.
In TV mode ,press the button and the number button to select a channel
8. MENU
Press to return to the root menu in DVD mode.
In radio mode, press to switch between radio main screen and RDS screen.
9. [ / ][ / ][ / / / ]/ENTER
In playback mode perform [fast reverse/fast forward][previous track/next track]
[upwards/downwards/leftwards/rightwards]; press ENTER to validate.
10. RPT
In playback mode, press to select a repeat mode.
ress to mute the device. Press it again to resume previous sound level.
In radio mode, press to browse each
playback
In other mode, press to
REPEAT, TIME DISP. Then press
16
17
Page 20
11. /PTY
In radio mode, press this button to switch to RDS program type.
In DVD/VCD mode, press to play slowly.
12. ZOOM/AF
In radio mode, press this button to function AF on/off.
In DVD/VCD mode, press to increase or decrease the picture in size.
13. SRC/IR-SW
ress the button repeatedly to switch sources. change
PPress and hold this button to
the IR to control front or rear source.(*It is disable when rear source shut off.)
14. VOL-/SEL/VOL+
Press VOL-/VOL+ to adjust volume.
Press SEL to select one of the control item:L-front/R-front/L-rear/R-rear/Subwoof/Bass/
Middle/Treble/Angle/Volume.
Then press VOL+/- to adjust each item.
15.
Press to eject a disc.
16. LOUD/
Press this button to activate LOUD function.
In bluetooth mode, press this button to hand down your calling.
17. (0-9)NUMBER BUTTON
In radio(TV) mode,
press the number button to select a corresponding preset station
(channel).
In DVD/VCD/CD mode, press to select any chapter or track directly.
In bluetooth mode ,press to input the telephone number.
18. CLEAR
Press the button to clear the erroneous number what you import.
19.
Press to pause playing and press again to resume playing.
20. TITLE
In DVD mode, press the button to return the title menu.
In VCD mode, press this button to turn on/off PBC function.
21.
Press to stop playback.
22. BAND/P/N
In radio mode, press to select bands.
In DVD/VCD mode, press P/N button to select PAL AUTO or NTSC.
23. SETUP
In playback mode, short press to display DVD setting, long press in DVD mode and
press in other modes will display system settings.
24. AUDIO/ST
In DVD mode, press to change the audio language.
In VCD mode ,press to change the channel mode.
In radio mode, press to select stereo or mono reception.
25. RDM/TA
In radio mode, press this button to function TA on/off.
In playback mode, press to play tracks in a random order.
18
17
Page 21
BASIC OPERATION
1.Reset the Unit
¼òµ¥¹ÊÕÏÅųýÖ¸ÄÏ
Operating the unit for the first time or after replacing the car battery, you must reset the
unit.Press RESET button on the head unit with a pointed object, (such as a ballpoint
pen) to set the unit to initial status.
*This function can only be operated by the head unit.
2.Turning the Unit On/Off
Press PWR/ button on the remote control to turn on the unit. In unit ON, when insert
a disc, the unit will automatically start playing. Long press it to turn off the unit completely.
Pressing PWR/MUTE button on the front panel also performs the same operation.
Note:
After the unit is off, the volume level is memorized during the area between 0 and 30.
If it is set less than 6, it will resume to 6; if the set volume level is higher than 30,
it will resume to 30; if it is between 6 and 30, it still stores in the status which you set.
3.Volume Control
Press VOL+ button on the remote control to increase the sound level and press VOL-
button on the remote control to decrease the sound level.
Press (VOL+ or VOL-) on the front panel also performs the same operation.
4.Setting the Sound Characteristics
Repeatedly press SEL button or press SEL button on the remote control to select the
desired mode in the following order:
L-front R-front
Volume
Angle
L-rear R-rear
Treble
Subwoof
Bass Middle
Note:
* After selecting the desired mode,you can adjust the current level by press the -/+ button
or pressing VOL-/VOL+ buttons on the remote control.
fter adjusting the Angle item, the unit will memorize the angle of the panel.
A
* If you don t adjust VOL button in 3 seconds after selecting the desired mode, the
,
function will be cancel.
5.Mute Function
Press PWR/ button to shut off the sound output. MUTE will be displayed on the
screen. Press it again to resume to previous volume level.
Press PWR/MUTE button on the panel also performs the same operation.
6.EQ Setting
While listening to the popular music, classic music or rock music, you can select the
corresponding preset modes to adjust the sound quality perfectly by using EQ button on
the remote control. Repeatedly pressing EQ button to choose the following modes in turn:
POP
EQ OFF
CLASSIC
ROCK
18
19
Page 22
RADIO OPERATION
Selecting the radio mode, the TFT display as the follows:
Display the current status
1.Band Selector
Page1
In radio mode, repeatedly press BAND button on the remote control to select a band in
the following order:
FM1
FM2
FM3
MW2MW1
*Pressing BAND on the touchable screen or on the panel also performs the same operation.
2.Manual/Automatic Tuning
(1).Automatic Tuning: Press / button on the remote control to search for a station in
the direction of lower frequency or higher frequency.
(2). Manual Tuning: Press and hold or button repeatedly to move downward or upward
one step respectively until the desired station frequency is displayed.
*Press(press and hold) / button on panel also performs the operation.
3.Recalling a preset station
A total of 30preset stations (18-FM,12-MW) are available in memory.
Press / button on the remote control to recall a preset station.
The display shows the preset number and frequency of the stored station, touch one of
these to select a corresponding station to listening.
*Press one of the station preset button on the remote control also selects preset station.
4.Automatic/Manual Store
Auto store is a function for storing up to 6 stations.
(1)Select the desired band.
(2)Hold down AMS button ,the stations with good reception are stored automatically.
Manual store: turn in a station you wish to store in the preset memory, press and hold
one the preset buttons (1-6) that you want to store on.
*If you store a station in a preset memory which already has a station the current station
will be cleared and replaced with the new station.
5.DX/LOC Selector
In radio mode, press LOC button on the remote control to select strong or weak station
reception.
(1). It is set to LOC mode when LOC button is first pressed. Loc:ON appears on the
screen and only strong signal station will be tuned.
20
19
Page 23
(2).It is switched to DX mode when Loc: OFF is pressed again. Both strong and weak
stations can be received.
Note:
* The initial mode is DX mode.
6.MO/ST Selector
In FM of radio mode, you can press ST button on the remote control to select Mono mode
or Stereo mode.
RDS (RADIO DATA SYSTEM) OPERATION
The RDS allows you to receive a variety of information such as traffic information,
station names, and to automatically retune to a stronger transmitter that is
broadcasting the same programme.
Tips
The RDS digital data includes the followings:
PI Programme Identification
PS Programme Service Name
AF List of Alternative Frequencies
TP Traffic Programme
TA Traffic Announcement
PTY Programme Type
EON Enhanced Other Networks
Turn on/off the AF function
* Press AF button to switch on/off AF function.
* The tuner will search for a station with RDS information.
* The tuner will retune frequencies whenever the reception signals getting worse.
Receiving Traffic information
1.Press the TA button to switch on TA mode.
2.The unit search for traffic information station automatically. When a traffic information
station is tuned in,the TP mark display on touchable screen. If you do not want to listen to
the traffic information being received,press TA button to skip that traffic information message. The TA function will remain in the ON position. And the unit will be back to previous mode.
3.Press it again to switch off TA mode.
* Traffic information is heard only when it is being broadcast.
In other mode,Traffic announcement can interrupt the source sound output when broadcast.
After broadcasted ,the unit will automatically return to the original source play before the
traffic information broadcast began.
20
21
Page 24
PTY(Programme Type)Tuning
The PTY function allows you to search for stations with a particular Program Type.
Touching Page1 button on the radio display screen to switch to the RDS screen
EON:OFF REG:OFF
PTY:NONE
RT:
TAAF
PTY
1.Press PTY button on touchable screen or on the remote control to select a programme
87.50MHz
PS:
PTY:
Page2
Seek+
Seek-
type. After selecting the programme type for 3 seconds, the unit will search for a station
in the selected programme type.
*If the PTY station is found, the tuner will be stop searching.
*If the PTY station is not found, No Pty will be display on the screen.
All types for your selection are listed in table as below:
NEWS
CURRENT AFFAIR
INFORMATION
SPORTS
EDUCATION
DRAMA
CULTURE
SCIENCE
VARIED
POP MUSIC
ROCK MUSIC
M.O.R. MUSIC
LIGHT CLASSIC
SERIOUS CLASSIC
OTHER MUSIC
WEATHER
FINANCE
CHILDREN
SOCIAL AFFAIR
RELIGION
PHONE IN
TRAVEL
LEISURE
JAZZ MUSIC
COUNTRY
NATIONAL
OLDIES
FOLK
DOCUMENTARY
TEST
ALARM
An emergency broadcasting(ALARM) will broadcast automatically and produce the
beep sound when it is received. The sound output through other source will be muted.
22
21
Page 25
BLUETOOTH OPERATION
HANDS-FREE PHONE
The unit is compatible with Bluetooth international standard wireless communisation
technology. You can place a hands-free call by using a Bluetooth compatible with the
mobile phone.
*When you place a call, speak loudly and clearly.
*Shut the windows before calling.
*It is normal that some unnatural voice may be heard during your calling which may be
caused by the conditions of the signals or the one who use the mobile phone.
*Due to some special mobile phone, you may not be able to use a hands-free phone.
CONNECTING
selecting B T mode
Press PAIR button on touchable screen
to turn on the par function
Searching for device(EONON) by using
mobile phone
Selecting bluetooth device
(EONON) by using mobile phone
Input a pass code:1234
The connection is made
The screen displays CONNECTED.
*The Bluetooth setting is required for a mobile phone. Read the Owner s Manual of the
,
mobile phone.
*After paired ,the unit can connect with the mobile phone automatically. in valid range
* If the mobile phone and the device are disconnected accidentally, the screen will display
Disconnect, just press LINK button on the screen to reconnect(refer to Bluethooth setup ).
23
Page 26
Dialling a call
Input the number required by pressing number button on the remote control or on the
1.
screen then press button on the screen to dial up.
The telephone number you dial ed is appeared on the
2.Placing a call by history:
Press button to switch to PHONE BOOK screen. You can place a call by selecting
a person from a list of received calls dialed calls or missed calls.
A maximum of 16 numbers can be stored in each call history. a maximum of 4 numbers
be display in each page, and touch >> button to turn to next page.
lscreen
Receiving a Call
When a call is received, a received call sound rings ,and the coming call is announced in
the display. Press button on the screen to starts the call.
Hanging up a Call
Press button on the screen to finishes the call.
*Press / button on the remote control also performs dial(receiving) a call or hang up a
call function
*The incoming call will interrupt the sound output through other source, and switch to the
hands-free phone screen automatically when it is received.
After the call is over, the unit will be back to previous mode.
* The hands-free phone sounds output through the built-in speakers. When calling, press
Audio Transfer button on the screen to switch the mode to receive a call by using mobile
phone, and press it again to return to hands-free mode.
24
23
Page 27
BLUETOOTH AUDIO FUNCTION
Audio information of a bluetooth compatible mobile phone, portable player, etc.,
is by wireless controllable/playable from the unit.
Refer to CONNECT to connect bluetooth audio devices.
Refer to bluetooth setup(PAGE6) for operation
*video playback is not supported.
*using remote control also perform same operation
The key of the remote control assigned in Bluetooth audio function
Play/pause
Previous/next track
Stop playback
24
25
Page 28
DVB-T OPERATION
This equipment will serve you with the available received channels supplied by
the mobile signals. Press SRC button on the panel or on the remote control or
touch on the left top of the screen then select TV mode.
Touch at random area to start the operation.
Main menu:
1
3
2
5
4
1.
To display the channel list
2.
To be back to previous interface
3.
To adjust the volume control
4.
To display the main menu
5.
To select the channels
Search automatically
Display setup
Language
To switch the languages
of the channels and touch OK button
to select.
Screen
To adjust the ratio and format of the screen.
OSD
To setup the background of the screen.
SYSTEM SETUP
The unit can receive and store the
channels according to the strength of
the signal received after finishing
searching the channel, all the searched
station will be displayed and touch
button to save it.
Touch to be back to previous menu.
Search manually:
Touch button to switch frequency
and touch OK button to confirm it.
26
Country To select the country or area.
*The preset channels will be cleared
if the setup is changed.
Version To displaythe version info.
Reset Default To reset the setting.
*All the preset setting will be cleared.
When a channel is searched, touch
button to display the channel list.
Press >>I/I<< buttons on the remote
control or touch button to select
channels and touch button to
watch the selected channels.
Touch / button to switch modes
between TV and radio and touch
button to confirm the selection.
Page 29
DVD OPERATIONS/VCD/CD
Loading a disc
1.Press button to open the front panel.
2. Insert a disc into the Disc slot the unit switch to the DVD mode automatically
* You can eject a disc by pressing button on the unit.
Quick track selection fast forward/fast reward playback
During playback mode, press / button to select next/previous chapter or track.
*Press / button on the unit also perform the same operation.
Press the/button on the remote control to perform fast reward or fast forward.
Repeatedly press the button ,the options switch as following order:
32
*Press and hold the/button on the unit will perform the same function.
Stop the playback
Press button to stop playing, then press ENTER button to play the current chapter or
track, press button twice to stop playing completely, then press ENTER button to play
the beginning of disc.
Pause the Playback
Press button to pause the playback,press it again to return to normal playback.
*Pressing button on the front panel also perform the same operation.
Playing Tracks in Random Order
During DVD/VCD/CD playback, press RDM button, RANDOM will appear on the
display, the unit plays any track at random and the number selection is de-available.
Press it again to return to normal playing.
Repeat Playing
In playback mode, press RPT on the remote control to perform replaying function when
you need to repeat the chapter you like.
During DVD playback, the replay option change in following order:
CHAPTER
OFF
TITLE
During VCD /CD playback, the replay option change in following order:
TRACK
OFF
*The defaulted setting is disc repeated.
Slow motion playback
In DVD mode, press repeatedly to slow forward or slow reward, as follows:
1 2
1 4
1 8
repeatedly In VCD mode,press to slow forward in following order
1 16
1 4 1 8 1 16
1 2
.
26
27
Page 30
1 4
1 8
1 16
1 2
Normal Play
This function is operated by using the remote control.
Increase or decrease the size of the picture
During DVD/VCD playback, press ZOOM button to increase or decrease the picture size.
There are 6 sizes, and press the button repeatedly to change the size in following order.
1 4
X3
1 3
4X
1 2
2X
OFF
*This function is operated by using the remote control.
Selecting the channel mode
(VCD mode)
In VCD mode, press the AUDIO button on the remote control repeatedly to select the
channel mode in the following order:
MONO LEFT
STEREO
MONO RIGHT
MIX-MONO
Programmed playback
In DVD/VCD/CD mode, press the PROG button and the program menu will be displayed.
Press the number buttons to select the track number. Use the direction buttons to move
the cursor to START and press ENTER to start programmed playback. Move the cursor
to EXIT and press ENTER to exit the programmed playback. Move the cursor to PREV
and press ENTER to go to the last page; move the cursor to NEXT and press ENTER to
go to the next page. During this process, press PROG to cancel the programmed playback.
* This function can only be operated by using the remote control.
Changing the subtitle language(Multi-subtitle)
With DVDs featuring multi-subtitle recordings. You can press SUB-T to switch between
subtitle languages during playback.
Selection options switch as follows:
Subtitle 01
Subtitles 2
Subtitles OFF
Notes:
* This function only operates with DVDs featuring multi-subtitle recordings.
* This function is operated by using the remote control.
Changing the audio language
DVDs can provide audio playback with different language. With DVDs featuring multiaudio
recordings, you can press AUDIO button to switch between language and audio systems
during playback. Selection options switch as follows:
Notes:
Audio 01
Audio 02
* This function only operates with DVDs featuring multi-audio recordings.
* This function is operated by using the remote control.
28
27
Page 31
Selecting different title (DVD mode)
For DVD disc, you can press TITLE on the remote control to return the top menu of the
disc, and you can select different chapter or title upward or downward by using
or .
*Touching the screen also perform the same function(refer to page 7 Multi-player
operation for detail).
Selecting root menu(DVD mode)
For DVD disc, you can press MENU to select different root menus, and then press
[ENTER] buttons to enter the sub-menus. With pressing
buttons, and the number buttons then ENTER button to select and enter what
you desired.
Setup menu
In DVD/VCD/CDmode, press SETUP,the screen will display system setting picture,
the user can select some relative constant parameters. The user also can set it as
needed by moving the cursor and using buttons, and then press ENTER
to execute the selecting or entering item.
*This function is operated by using the remote control.
Notes:
* The selections are the preferred options that will be chosen if they are available on a
disc. If the disc that is inserted does not have the preferred option then the discs own
preference will be used.
* Regarding SETUP MENU, please refer to the following pages for more details.
* Some functions varies depending on the types of models or formats of the disc.
Auto switch to video
When playing DVD in driving car,there is
display on screen. Just braking car, the screen can switch to video automatically.
Auto switch when revering the car
The unit can switch to the radar of revering the car automatically,when revering the car.
Attention: Cann t use function When driving
,
29
Page 32
SYSTEM SETUP
When you press SETUP button on the remote control, or press SETUP button on the screen, the setup menu
will be displayed. It includes General Setting, Audio Setup, Preference ,Password Setup and Exit Setup menu.
1.Within the setup menu, you can use[ ][ ][ ][ ] buttons on the remote control to move the cursor,
and then press the ENTER button to make your selection.Press [ ] can return to the previous menu.
2.To exit setup menu, you can select the EXIT item in sub-menu or press SETUP button.
Note:touching the item on the screen also performs same operation.
1. GENERAL SETUP PAGE
1.1 TV DISPLAY
GENERAL SETUP PAGE
TV DISPLAY
OSD LANGUAGE
SET TV DISPLAY MODE
The TV Display which select the different ratio of display format and the screen of TV, There are
various types of display on screen for different matches between Disc and TV.
Note:
No matter which display format is selected, a picture recorded in standard 4:3 format always displays in
the 4:3 aspect ratio.
The display format of DVD titles may vary; please refer to the information that accompanies your specific
DVD title.
If the DVD title is recorded in 16:9 wide display format while the TV is a standard 4:3 screen, horizontal
compression of the image will result.
Some DVD titles may be recorded in special formats. In such cases, the DVD titles will always appear on
the screen in their original format,regardless of which TV display format you select.
WIDE
ENG
4:3 PAN SCAN
4:3 LETTER BOX
16:9 WIDE
1.2 OSD LANGUAGE
On Screen Display(OSD)Language:Users can select the on-screen display language.
GENERAL SETUP PAGE
TV DISPLAY
OSD LANGUAGE
SET OSD LANGUAGE
WIDE
ENG
ENGLISH
FRANCAIS
DEUTSCH
ITALIANO
PORTUGUES
ESPANOL
2. AUDIO SETUP PAGE
30
Page 33
User can select digital audio setup or dolby digital setup.
AUDIO SETUP PAGE
DIGITAL AUDIO
DOLBY DIGITAL SETUP
GO TO AUDIOSETUP PAGE
2.1 DIGITAL OUTPUT SETUP
DIGITAL AUDIO PAGE
DIGITAL OUTPUT
LPCM OUTPUT
SETUP SPDIF
OFF
48KHz
SPDIF OFF
SPDIF RAW
SPDIF PCM
- SPDIF OFF: An analog surround sound format is output through the back-panel connections for
L,R,LS,RS and centre speakers, and the subwoofer simulation.
-SPDIF RAW: outputs the analog surround sound format and digital audio signal.
-SPDIF PCM :outputs the digital audio signal only.
2.1 DOLBY DIGITAL SETUP
DOLBY DIGITAL SETUP PAGE
DUAL MONO
DYNAMIC
DUAL MONO(1+1) SETUP
DUAL MONO:User can switch the binaural mode.
DYNAMIC:Select the provided option to change the Dynamic range setting.
STR
STEREO
L-MONO
R-MONO
MIX-MONO
3. PREFERENCE SETUP PAGE
The preference setting is active only when disc has been stopped completely, and the setting is
effective on next time power on till exchanging the saved setting.
3.1 AUDIO
AUDIO: Sets the preferred audio language as the default when playing DVD. (If DVD support these
languages).
31
Page 34
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
PREFERRED AUDIO LANGUAGE
ENG
ENG
ENG
ENGLISH
FRENCH
SPANISH
PORTUGUES
JAPANESE
KOREAN
RUSSIAN
THAI
3.2 SUBTITLE
SUBTITLE: Sets the preferred subtitle language as the default when playing DVD.(if DVD support
these languages).
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
PREFERRED SUBTITLE LANGUAGE
ENG
ENG
ENG
ENGLISH
FRENCH
SPANISH
PORTUGUES
JAPANESE
KOREAN
RUSSIAN
THAI
3.3 DISC MENU
DISC MENU: Sets the preferred menu language as the default when playing DVD.(if DVD support
these languages).
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
PREFERRED MENU LANGUAGE
ENG
ENG
ENG
ENGLISH
FRENCH
SPANISH
PORTUGUES
JAPANESE
KOREAN
RUSSIAN
THAI
3.4 PARENTAL
PARENTAL: The parental control function works in conjunction with the different censorship classes
assigned to DVDs. These classes help to control the types of DVDs that the family watches, there
are up to 8 censorship classes for DVDs.
Note:
The PARENTAL is changeable when 4.1 PASSWORD MODE set to OFF.
After setting the level of parental control. Please set the password as ON to perform the lock of changing.
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
SET PARENTAL CONTROL
ENG
ENG
ENG
1.KID SAF
2.G
3.PG
4.PG 13
5.PG R
6.R
7.NC 17
8.ADULT
3.5 DEFAULT
DEFAULT: Resets to the initial factory setups.Press ENTER button to confirm.
32
Page 35
PREFERENCE PAGE
AUDIO
SUBTITLE
DISC MENU
PARENTAL
DEFAULT
LOAD FACTORY SETTING
ENG
ENG
ENG
RESET
4. PASSWORD SETUP PAGE
4.1 PASSWORD MODE
PASSWORD MODE: Sets the function operation to locking the parental function.
ON: Using the parental control must input the password.
OFF: You can not input the password to change the parental control.
* The initial password is 136900.
PASSWORD SETUP PAGE
PASSWORD MODE
PASSWORD
PASSWORD MODE
ON
ON
OFF
4.2 PASSWORD CHANGE
PASSWORD CHANGE: You can change the password, please type 6 numerals as new password.
PASSWORD SETUP PAGE
PASSWORD MODE
PASSWORD
CHANGE PASSWORD
ON
CHANGE
OLD PASSWORD
NEW PASSWORD
CONFIRM PWD
OK
Note:Touching the position where inputting password, the screen will display the number button,and
user can input the password by touching number button.
5. EXIT SETUP MENU
EXIT SETUP MENU
Moving the cursor to by using direction key on the remote control, then press ENTER button to
exit the setup. Touching the to exit directly.
32
33
Page 36
SETTING THE TV SCREEN SIZE
Multi-aspect ratios suit to different TV screen size.
Picture format
on Disc
4:3
16:9
Pan Scan
TV Screen Size
4:3
Letter-box Wide Screen
16:9
Function supported by DVD discs
There are many functions available on DVD discs and the functions vary per player and
per manufacturer.
34
2
Regional code and signal system
Dolby digital surround sound
DTS surround
Number of languages
Subtitle languages
Picture proportion modes
Parent lock
Angles for viewing
Closed Caption
Page 37
MP3 OPERATION
Playing a disc, an SD/MMC card or a USB device containing files
Connect a USB device or press
button to open the front panel, insert a disc into the
MP3
disc slot or SD/MMC card into the card slot. The unit will automatically switch on when
a disc, card or USB device is inserted. The screen will display as follow:
Touch this area to display number keyboard.
PAUSE
02:47 03:40
001/099
STOP
PREV
NEXT
SETUP
MP3
01 LA LUNE
01IN PARADISUM
02 NO ONE LIKE
02 WINTER IN J
02eden
03 SCARBOUGH
PLAY
ouch the / button on the screen to turn pages.
T
*Press / button on the remote control when stop playback also performs the same
function
*You can eject a disc by pressing button on the unit.
Repeat playing
When playing MP3 files, press the RPT button repeatedly on the remote control to select
repeat mode: REPEAT ONE, OFF. While in REPEAT ONE mode, it will play one track
repeatedly. The defaulted mode is REPEAT ALL mode, the unit will play all tracks repeatedly.
Track selection
-Skip track backward/forward
When playing MP3 files, press / button on the remote control
button on the touchable screen
to go to the previous or next track.
- Selecting track by using number button
Selecting any track directly by using Number button(0-9).
To select more than 9 track number, press the corresponding number buttons continuously.
For example, if you want to play the 23th track, just press button 2 and then press button 3
and the corresponding track will be played.
Note:
* This function can be operated using the remote control or touch top right corner of screen
to be functioned.
* If you make a mistake, press CLEAR button to clear.
or press NEXT/PREV
35
Page 38
Stop playing
When playing MP3 files, press button on the remote control to stop playback.
Pause playback
Press thebutton on the remote control or press PAUSE button on the touchable
screen while playing, press it again or press PLAY button on the touchable screen
to return to normal playback.
Fast-forward/fast-backward playing
Press / button on the remote control to select the speed of fast playing in backward
or forward direction:
*Long press / button continuously on the front panel also perform the same
function.
2 --4 --8 --16 --32 --
ISO FILE OPERATION
When playing the media with folders, press the / button on the remote control
or PREV/NEXT buttons on the screen to move the cursor to current folder then press
ENTER button on the remote control to confirm, and the first track of the current
folder will be played.
36
35
Page 39
INSTALLATION
Notes
Before finally installing the unit, connect the wiring temporarily, making sure it is all
connected up properly, and the unit and the system work properly.
Use only the parts included with unit to ensure proper installation. The use of unauthorized
parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other
modifications of the vehicle.
Install the unit where it does not get in the driver's way and cannot injure the passenger
if there is a sudden stop.
The semiconductor laser will be damaged if it overheats, so don't install the unit anywhere
hot--for instance, near a heater outlet.
If installation angle exceeds 30 from horizontal, the unit might not give its optimum
performance.
30
The cords must not cover up the area shown in the figure below. This is necessary to
allow the enginery to radiate freely.
Do not close this area
38
37
Page 40
INSTALLATION
Install the unit
After inserting the holder into the dash-board,select the appropriate tabs according to the
thickness of the dash-board material and bend them.(Install as firmly as possible using the
top and bottom tabs. To secure, bend the tabs 90 degrees.)
Insert the keys supplied to the unit at both sides of the unit (shown as illustrated)until
they click. Pulling the keys makes it possible to remove the unit from the dashboard.
38
39
Page 41
TROUBLE SHOOTING
Common problems
Symptom
Power doesn't switch ON .
The unit doesn't operate.
Operation with the remote
control isn't possible.
Playback is not possible.The disc is dirty.
There's no sound.
The prohibited mark is
displayed and operation is
not possible.
The picture stops (pauses)
and the unit cannot be
operated.
There's no sound Volume
level is low.
There's audio and video
skipping.
Cause
Leads and connectors are
incorrectly connected.
A fuse has blown.Fix the problem causing the blown fuse
Noise and other factors are
causing the built-in microprocessor to operate incorrectly.
The remote control operation
mode is incorrect.
Battery power is low.Load new batteries.
Some operations are prohibited
with certain discs.
The loaded disc is a type this
unit cannot play.
Non compatible video system
disc is loaded.
Connections are incorrect.Check connections
With some discs,96kHz output
is prohibited.
The unit is performing still F.FWD
or F.REV playback.
The operation is prohibited for
the disc.
The operation is not compatible
with the disc's organization.
Reading of data has become
impossible during playback.
The volume level is low.
This unit is not firmly secured.Secure this unit firmly.
Remedy
Confirm once more that all connections
are correct.
and replace the old fuse with a new one
of the same capacity.
Reset the unit.
Switch to the correct remote control
mode.
Check using another disc.
Clean the disc.
Check the type of the disc.
Change to a disc compatible to your
video system.
Switch the output setting to 48 Khz.
There is no sound during still F.FWD ,
F.REV playback.
This operation is not possible.
This operation is not possible.
After pressing once start playback
once more.
Raise the volume level.
The picture is stretched the
aspect is incorrect.
When the ignition switch is
turned ON (or turned to ACC),
the motor sounds.
The aspect setting is incorrect
for the display.
This unit confirms whether a
disc is loaded or not.
Select the appropriate setting for your
display.
This is a normal operation.
39
Page 42
Problem during DVD playback
Symptom
Playback is not possible
Cause
The loaded disc has a different
region number from this unit
Dialog language (and
subtitle language) can not
be switched.
The DVD playing does not
feature multiple language
recordings.
You can only switch between
options indicated in the disc menu
No subtitles are displayed
The DVD playing does not feature
subtitles
You can only switch between
options indicated in the disc menu
Playback is not with the
audio language and subtitle
language settings selected
in SET UP MENU
The picture is extremely
unclear/distorted and dark
during playback
The DVD playing does not
feature dialog or subtitles in
the language selected in the
SET UP MENU
The disc features a signal to
prohibit copying (some discs
may have this)
Problem during Video CD playback
Remedy
Replace the disc with one featuring the
same region number as this unit
You cannot switch among multiple
languages if they aren't recorded on
the disc
Switch using the disc menu
Subtitles are not displayed if they are
not recorded on the disc
Switch using the disc menu
Switching to a selected language is not
possible if the language selected in the
SET UP MENU is not recorded on the disc
Since this unit is compatible with the copy
guard analog copy protect system. when
playing a disc that has a signal prohibiting
copying the picture may suffer from
horizontal stripes or other imperfections
when viewed on some displays. This does
not mean this unit is malfunctioning.
Symptom
The PBC(playback control)
menu display cannot be
called up.
Repeat play and track/time
search are not possible
40
Cause
The video CD playing does not
feature PBC
Remedy
This operation is not possible with video
Cds not featuring PBC
USB connector--------------------------------------------------------------------------- X1
AV cable ---------------------------------------------------------------------------------- X1
Screws ----------------------------------------------------------------------------------- X 4
40
41
Page 44
SPECIFICATON
GENERAL
power requirement ----------------------------------------------
grounding system ----------------------max: current consumption ----------max: power output --------------- 65Wx4
load impedance ---------------------dimensions--------------------------------------------MM
S/N ratio ------more than 62dB(1kHz)
dynamic range ------------------more than 80dB(1kHz)
distortion -----------------------less than
video output --------------------------------------audio output (RCA) ---------------------- 2.0Vrms+0.3V 10K
frequency range -----------------------------------------65.0~74.0/87.5~108.0MHz
usable sensitivity ---------------------------------------------------------------10dB
S/N ratio -------------------------------------------------------------------- 50dB(mono)
distortion --------------------------------------------------------------------0.5%(mono)
stereo separation ---------------------------------------------- 30dB(65dBu,1kHz)
MW TUNER
frequency range ----------------------------------------------------- 522~1620 kHz
usable sensitivity --------------------------------------------------------------- 30dB
signal-to-noise ratio ------------------------------------------------------------- 40dB
42
Page 45
Page 46
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.