Enviro Nova Q1L Owner's Manual

Download

Page 1

WARRANTY REGISTRATION

enviro.com/warranty

Q1L

D I R E C T V E N T F I R E P L A C E - N o V A

OWNER’S MANUAL

WARNING: If the information in this manual is not followed exactly, a

re or explosion may result causing property damage, personal injury

or loss of life. Installation and service must be performed by a qualied

4001609

Version Française: www.enviro.com/fr.html

installer, service agency or the gas supplier.

50-2999

Page 2

Safety Precautions

WARNING: FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious

injury, death, or property damage.

- Do not store or use gasoline or other ammable vapors and

liquids in the vicinity of this or any other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immeadiately.

• Immeadiately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualied

installer, service agency or the gas supplier.

INSTALLER:

Leave this manual with the appliance.

CONSUMER:

Retain this manual for future reference.

This appliance may be installed in an after-market permanently located,

manufactured (mobile) home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases, unless a certied kit is used.

Massachusetts installations (Warning): This product must be installed by a licensed plumber or gas tter when installed within the Commonwealth of Massachusetts. Other Massachusetts code requirements: Flexible connector must not be longer than 36in., a shut off valve must be installed; only direct vent sealed combustion products are approved for bedrooms/bathrooms. A carbon monoxide detector is required in all rooms containing gas red direct vent appliances. The replace damper must be removed or welded in the open position prior to installation of a replace insert.

Page 3

Safety Precautions

FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:

• All ENVIRO gas-red appliances must be installed in accordance with their instructions. Carefully read all the instructions in this manual rst. Consult the building authority having jurisdiction to determine the need for a permit prior to commencing the installation.

• NOTE: Failure to follow these instructions could cause a malfunction of the replace, which could result in death, serious bodily injury, and/or property damage.

• Failure to follow these instructions may also void your re insurance and/or warranty.

GENERAL

• Installation and repair should be done by a qualied service person. The appliance should be inspected before the rst use and, at least, annually by a qualied service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. It is imperative the control compartments, burners and circulating air passageways of the appliance be kept clean.

• Due to high temperatures, the appliance should be located out of high trafc areas and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burn or clothing ignition.

• Young children should be carefully supervised when in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to a replace or stove install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces. Any safety screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

• Clothing or other ammable materials should not be placed on or near the appliance.

DANGER

HOT GLASS WILL

CAUSE BURNS

DO NOT TOUCH

GLASS UNTIL COOLED.

NEVER ALLOW

CHILDREN TO TOUCH

GLASS.

FOR YOUR SAFETY

• Installation and service must be performed by a qualied installer, service agency or gas supplier.

• This installation must conform to local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1.

• To prevent injury, do not allow anyone who is unfamiliar with the stove to operate it.

• To prevent injury, if the pilot or pilot and burners have gone out on their own, open the glass door and wait 5 minutes to air out before attempting to relight the stove.

• Always keep the area around these appliances clear of combustible material, gasoline and other ammable liquids and vapours.

• These appliances should not be used as a drying rack for clothing or for hanging Christmas stockings/decorations.

• Due to the paint curing on the stove, a faint odor and slight smoking will likely be noticed when the stove is rst used. Open a window until the smoking stops.

Always connect this gas stove to a vent system and vent to the outside of the building envelope. Never vent to another room or inside the building. Make sure the specied vent pipe is used, properly sized and of adequate height to provide sufcient draft. Inspect the venting system annually for blockage and signs of deterioration.

WARNING: Failure to position the parts in accordance with the diagrams in this booklet, or failure to use only parts specically approved with this appliance, may result in property damage or personal injury.

WARNING: Do not operate with the glass front removed, cracked or broken. Replacement of the glass should be done by a licensed or qualied service person.

• Never use solid fuels such as wood, paper, cardboard, coal, or any ammable liquids, etc., in this appliance.

• Do not use this appliance if any part has been under water. Immediately call a qualied service technician to inspect the appliance and to replace any part of the control system or any gas control which has been under water.

• Do not abuse the glass by striking it or slamming the door shut.

• If the Q1L unit is pulled out of its installation, and the ventair intake system is disconnected for any reason, ensure that the vent-air intake pipes are reconnected and re-sealed in accordance to the instructions noted in

- DIrect Vent

InItIal InstallatIon

Page 4

Table of Contents

Safety Precautions........................................................................................................2

Table of Contents.........................................................................................................4

Codes And Approvals....................................................................................................5

Specications.............................................................................................................6

Dimensions.....................................................................................................6

Rating Label Location.........................................................................................6

Operating Instructions..................................................................................................7

Lighting Instructions..........................................................................................7

Pilot Light.........................................................................................................8

Air Shutter.........................................................................................................8

Remote Controls................................................................................................8

Burner Lighting.................................................................................................9

Blower Speed ...................................................................................................9

Normal Sounds During Operation........................................................................9

Maintenance And Service..............................................................................................10

Routine Maintenance........................................................................................10

Cleaning The Glass............................................................................................10

Cleaning The Firebox.........................................................................................10

Replacing the Glass...........................................................................................10

Cleaning Decorative Surfaces............................................................................11

Glass Door Removal.........................................................................................11

Burner Removal...............................................................................................12

Fuel Conversion...............................................................................................12

Initial Installation.......................................................................................................15

Introduction.................................................................................................15

Placement and Framing....................................................................................15

Rear Vent Conversion.......................................................................................16

Insulating Material...........................................................................................17

Standoffs............................................................................................18

Corner Installation...........................................................................................19

Mantle and Non-Combustible Clearances.............................................................20

Direct Vent......................................................................................................21

Venting Fireplace Inserts.................................................................................21

Vent Termination Restrictions............................................................................22

Venting Clearances..........................................................................................23

Approved Venting Parts.....................................................................................23

Vent Congurations and Restrictor Settings.......................................................24

Horizontal Termination - Rear Vent w/ No Rise.................................................25

Allowable Co-Axial Vent Congurations..............................................................26

Co-Linear Venting Adapter Kit (50-2982)..........................................................27

Air Restrictor Settings.......................................................................................29

Horizontal Termination.....................................................................................30

Vertical Termination ........................................................................................31

Solid Fuel Fireplace Installation........................................................................34

Gas Line Connection and Testing.......................................................................35

Electrical Requirements ...................................................................................36

Secondary Installation................................................................................................37

Fire Grate and Log Set Installation...................................................................37

Optional Porcelain Panels (50-2939) Installation & Removal.................................40

Trouble Shooting........................................................................................................41

Parts List....................................................................................................................42

Parts Diagram............................................................................................................43

Notes..............................................................................................................44

Warranty.................................................................................................................46

Installation Data Sheet...............................................................................................47

Page 5

Codes And Approvals

DIRECT VENT ONLY: This type is identied by the sufx DV. This appliance draws all of its air for combustion from outside the dwelling, through a specially designed vent pipe system.

This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above sea level.

In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas

Association guidelines which state: the sea level rated input of Gas Designed Appliances installed at elevations above 2000 (610 m) feet is to be reduced 4% for each 1000 feet (305 m) above sea level. Refer also to local authorities or codes which have jurisdiction in your area regarding the de-rate guidelines.

In Canada: When the appliance is installed at elevations above 4500 feet (1372 m), the certied high

altitude rating shall be reduced at the rate of 4% for each additional 1000 feet (305 m).

• This appliance has been tested by INTERTEK and found to comply with the established VENTED GAS FIREPLACE HEATER standards in CANADA and the USA as follows:

VENTED GAS FIREPLACE HEATER (Q1L; NG/LPG)

TESTED TO: ANSI Z21.88a-2009/CSA 2.33a-2009 VENTED GAS FIREPLACE HEATERS

CAN/CGA 2.17-M91 (R2009) GAS FIRED APPLIANCES FOR HIGH ALTITUDES

CSA P.4.1-02 TESTING METHOD FOR MEASURING ANNUAL FIREPLACE EFFICIENCY

This ENVIRO Q1L Fireplace:

• Has been certied for use with either natural or propane gases. (See rating label.)

• Is not for use with solid fuels.

• Is approved for bedroom or bed sitting room. (IN CANADA: must be installed with a listed wall thermostat. IN USA: see current ANSI Z223.1 for installation instructions.)

• Must be installed in accordance with local codes. If none exist, use current installation code CAN/CGA B149 in Canada or ANSI Z223.1/NFPA 54 in the USA.

• Must be properly connected to an approved venting system and not connected to a chimney ue serving a separate solid-fuel burning appliance.

IMPORTANT NOTICE (Regarding rst re up): When the unit is turned

on for the rst time, it should be turned onto high without the fan on for the rst 4 hours. This will cure the paint, logs, gasket material and other products used in the manufacturing process. It is advisable to open a window or door, as the unit will start to smoke and can irritate some people. After the unit has gone through the rst burn, turn the unit off including the pilot, let the unit get cold then remove the glass door and clean it with a good gas replace glass cleaner, available at your local ENVIRO dealer.

Page 6

21"

(533mm)

(93mm)

(417mm)

(112mm)

20"

(508mm)

(420mm)

(476mm)

(601mm)

(627mm)

(641mm)

(700mm)

(136mm)

(168mm)

(313mm)

10"

(254mm)

(199mm)

(477mm)

(429mm)

Dimensions:

(350mm)

(548mm)

(112mm)

(168mm)

Specifications

120V

Line

Plug

Figure 1. Q1L Dimensions - Top Vent

Gas

Rating LabeL & Lighting instRuctions Location:

The rating label plate and lighting instructions are located under the gas valve and attached to the unit

Figure 2. Q1L Dimensions - Rear Vent

with a length of chain.

Page 7

Operating Instructions

For Your Safety, Read Safety Precautions And

Lighting Instructions Before Operating

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY

RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE.

Lighting anD tuRning off instRuctions:

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING:If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life

A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS: Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier’s instructions. If you cannot reach your gas supplier, call the fire department.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this label.

2. Set the thermostat to the lowest setting.

3. Turn off all electric power to this appliance.

4. Open the front control panel.

5. Turn off the gas control knob clockwise to the “OFF” position.

6. Open door. Wait fIve (5) minutes to clear out any gas. Close door. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the saftey information above on this label. If you don’t smell gas, go to the next step.

7. Find pilot-located near the center rear of the firebox. Turn the gas control knob counter-clockwise to “PILOT”. Push the gas control in fully and hold, keep knob depressed for about 30 seconds after the pilot is lit. Release knob. If pilot goes out, repeat steps 4 through 5.

C. Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it. Call a qualified service technician. Force or attempted repair may result in a fire or explosion. D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

WARNING: This gas valve has a lockout device, which will not allow the pilot burner to be relit until the thermocouple has cooled.

-If the knob does not pop up when released, stop and immediately call your service technician or gas supplier.

-If the pilot will not stay lit after several tries, turn the gas control knob clockwise

8. Turn the gas control knob counter clockwise to the “ON” position.

Flip the burner switch to “ON” then turn the “HI/LOW” knob to the desired setting.

9. Close the front control panel.

10. Turn on all electric power to the appliance.

11. Set thermostat to desired setting.

to “OFF” and call your service technician or gas supplier.

1. Set the thermostat to the lowest setting.

2. Turn off all electric power to the appliance if service is to be performed.

3. Open the front control panel and flip burner switch to “OFF”

TO TURN OFF GAS TO APPLIANCE

4. Turn the gas control knob clockwise to the “OFF” position.

5. Close the front control panel.

C-12454

Figure 3. Lighting Instruction Label

Page 8

Operating Instructions

PiLot Light:

1. Turn off the gas to the replace. If not recently done, remove the glass and let the unit air out for at least ve (5) minutes to clear out any gas. Turn on gas to the heater. Leak test all joints

with soapy water. NEVER USE OPEN FLAME FOR LEAK TESTING.

2. Start the pilot by pressing the gas control knob and turning it to PILOT. While holding the gas control knob in, press the piezo ignitor several times until the pilot light starts. Hold the gas control knob in for 30 seconds. Check that the pilot has fully engulfed the thermocouple assembly (see Figure 4).

3. Start the main burner by turning the gas control knob to ON and then turn the rocker switch to ON. Check that all burner ports have ame.

Thermopile

Thermocouple

4. Leak test all gas joints again.

Figure 4. Pilot Flame

aiR shutteR:

The air shutter adjustment lever is on the right hand side of the venturi box (see Figure 5).

The air shutter allows the amount of air coming into the replace to be adjusted in order to accommodate different climates and venting arrangements. Start the pilot and then the burner. Make sure the pilot ame is burning normally and none of the burner ports are plugged. Let the replace burn for roughly fteen minutes and then examine the ames, compare the ames to Figure 40.

The ideal ame will be blue at the base and light orange above. The ames should be of medium height. If the ames look like this, no venturi adjustment is needed. If the ames are fairly short and

mostly blue, the replace is getting too much air. Therefore, the air shutter should be closed (pulled out) slightly until the correct ames are achieved. Flames that are very orange, with tall, dark, stringy tips, are not getting enough air. Open (push in) the venturi until the ames clean up. If the venturi is opened, or closed all the way, and the correct ames cannot be attained, turn off the gas and contact the dealer.

Less Air

Air Shutter Adjustment

More Air

Figure 5. Air shutter adjustment lever.

Remote contRoLs:

This replace can use an optional remote control or an optional cordless wall thermostat. If either of these are to be used to control the replace for the majority of the time, leave the ON/OFF switch (on the control panel) in the remote/thermostat position. Consult the instructions included with the remote/wall thermostat for operation guidelines.

Warning: Incorrect venturi adjustment may lead to improper combustion, which is a safety hazard. Contact the dealer if there is any concern about the venturi adjustment.

Page 9

Operating Instructions

For Your Safety, Read Safety Precautions And

Lighting Instructions Before Operating

buRneR Lighting:

A) Make sure the pilot is lit. B) Turn gas control knob COUNTER CLOCKWISE to ON. C) Flip the burner switch to ON. D) Turn HI/LO knob to the desired ame height. E) Turn on all electrical power to the unit.

NOTE: Check that all burner holes are lit.

TO TURN GAS FIREPLACE OFF:

Flip switch to OFF to turn off burners only.

If the replace is to be turned off for the season, or for servicing, turn the gas shut off valve to OFF. DO NOT FORCE IT. If the unit is going to be serviced, turn off the electrical power to the unit as well.

NOTE: When the unit is turned on for the rst time, it should be turned onto high, with the fan OFF, for the rst two to four hours. This will cure the paint, logs, gasket material, and other products used in the manufacturing process. It is advised that a door or window be opened as the unit will start to smoke, which can irritate some people. After the unit has gone through the rst burn, turn the unit OFF, including the pilot, and let the unit get completely cold. Then remove the glass and clean it with a good gas replace glass cleaner, available at your local Enviro dealer. See “MaIntenance anD serVIce; Glass Door reMoVal” and “MaIntenance anD serVIce; cleanInG the Glass.”

Gas Control

Hi/Low Knob

Piezo Ignitor

Alternate Burner

Switch Location

Figure 6. Control Panel

bLoweR sPeeD:

The blower will come on only when the replace is up to temperature (approximately 15 minutes). The speed of the fan can be changed by turning the fan control knob. The blower will continue to operate automatically after the unit has been shut off (approximately 25 minutes).To turn the blower off, turn the knob COUNTER CLOCKWISE until it “clicks” off (Figure 7).

It is advisable not to operate the blower below

/3 speed as it puts a strain on the windings of the blower and running the blower at lower speeds could also cause premature fan failure.

Figure 7. Fan Control

noRmaL sounDs DuRing oPeRation:

Table 1: Normal Sounds

Component Sound & Reason

Q1L & Surround Panels Creaking when heating up or cooling down. Burner Light pop or poof when turned off; this is more common with LP units. Temperature Sensor Clinking when it senses to turn the blower on or off. Pilot Flame Quiet whisper while the pilot ame in on. Blower / Fan Air movement that increase and decreases with the speed of the blower. The

blower is pushing the heat from the replace into the room.

Gas Control Valve Dull click when turning on or off, this is the valve opening and closing.

Page 10

Maintenance And Service

Routine maintenance:

At least once a year, run through the following procedures to ensure the system is clean and working properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not blocked by anything. The pilot ame should be blue with little or no yellow on the tips.

Warning: Clearances must be sufcient to allow access for maintenance and service

Warning: Failure to position the parts in accordance with this manual, or failure to use only parts

specically approved with this appliance may result in property damage or personal injury.

The venting system must be periodically examined; it is recommended the examination is done by a qualied agency.

cLeaning the gLass:

When the replace has cooled, remove the face of the replace along with the glass. See MaIntenance anD serVIce - Glass Door reMoVal. Check the gasket material on the back of the glass, making sure that

it is attached and intact.

During a cold start up, condensation will sometimes form on the glass. This is a normal condition with all replaces. However, this condensation can allow dust and lint to cling to the glass surface. Initial paint curing of the appliance can leave a slight lm behind the glass, a temporary problem. The glass will need cleaning about two weeks after installation. Use a mild glass cleaner and a soft cloth. Abrasive cleaners will damage the glass and painted surfaces. Depending on the amount of use, the glass should require cleaning no more than two or three times a season. Do not clean the glass when it is

hot.

cLeaning the fiRebox:

Remove the logs carefully, as they are very fragile. Gently remove all the coals and place on a paper towel. Vacuum the bottom of the rebox thoroughly. Carefully clean any dust off the logs and remove any lint from the burner and pilot. At this time, inspect the burner tube for cracking or severe warping. If a problem is suspected, contact the dealer. Check the logs for deterioration or large amounts of soot; a small amount on the bottom side of the logs is normal. Replace the logs and coals as in the seconDary

InstallatIon - FIre Grate anD loG set InstallatIon section. If new/more coals are required, contact your

nearest ENVIRO dealer.

RePLacing the gLass:

The glass in the replace is a high temperature ceramic. If the glass is damaged in any way, a factory replacement is required (see Parts lIst). Wear gloves when handling damaged glass door assembly to prevent personal injury. Do not operate with the glass front removed, cracked or broken. Removal and replacement of the glass from the door must be done by a licensed or qualied service person.

The glass must be purchased from an ENVIRO dealer. No substitute materials are allowed.

Remove the door (see page 11). The replacement glass will come with a new gasket installed. Remove any silicone remnants from the door. Apply high temperature silicone to the two vertical faces of the door and install the new piece of glass with gasket (be sure to maintain edge clearances). Apply even pressure to the glass to allow the silicone to adhere to the gasket material.

Page 11

Maintenance And Service

cLeaning DecoRative suRfaces:

Painted and porcelain faces should be wiped with a damp cloth periodically. If a plated face has been purchased, it should be unpacked/unwrapped carefully to avoid getting anything on the surface of the nish, including cleaners, polish and nger prints. It is important to note that ngerprints and other marks can leave a permanent stain on plated nishes. To avoid this, give the face a quick wipe with denatured alcohol on a soft cloth BEFORE lighting the replace. Never clean the face when it is hot. Do not use other cleaners as they may leave a residue, which can become permanently etched into the surface.

gLass DooR RemovaL:

In order to install the log set, and for regular cleaning, the glass door

Door Tool Hole

Figure 8. Top latches for glass door

Door Latch Mechanism

must be removed. There are two (2) door latch mechanisms on top the glass door as shown in Figure

8. Each latch has a hole at the front to use the door tool, supplied with the unit, to pull the mechanisms straight out and up. When the top latches are unhooked, lean the door forward and then lift it up out of the alignment slots at the bottom corners of the rebox, shown in Figure 9.

Alignment Slot (both corners)

*Parts removed

for clarity*

Figure 9. Bottom Alignment Slots for glass door.

To replace the glass door, simply reverse the above procedure.

Warning: Do not touch or attempt to remove the glass door if the replace is not completely cold.

WARNING: Never operate the replace with the glass door removed.

Page 12

Maintenance And Service

buRneR RemovaL:

The burner may need to be removed for a few reasons, including cleaning under the burner, converting the unit to a different gas type, or to replace the burner altogether. Proceed only when the unit has

completely cooled down.

1. Remove the glass door as shown in the

MaIntenance anD serVIce - Glass Door r

eMoVal.

2. Remove the log set and re grate as shown in S

Grate anD loG set InstallaIon

3. Push the air shutter in until it stops

4. Lift the burner straight up then out.

To re-install the burner follow steps 1-4 in reverse. When placing the burner back in the unit be sure to adjust the air shutter back to the correct setting.

econDary InstallatIon - FIre

Figure 10. Removing Burner.

fueL conveRsion:

TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY

Please read and understand these instructions before installing.

Warning: This conversion kit shall be installed by a qualied service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a re, explosion or production of carbon monoxide may result causing property damage, personal injury or loss of life. The qualied service agency is responsible for the proper installation of this kit. The installation is not proper or complete until the operation of the converted appliance is checked as specied in the manufacturer’s instructions supplied with the kit.

Kit Parts List:

1 - Orice (NG - #46 DMS or LP - 1.2 mm) 1 - Pilot Injector (NG 0.62 mm; LP 0.35 mm) 1 - Installation instruction sheet 1 - Conversion label

Carefully inspect all parts supplied with this conversion kit. If any parts have been damaged or are missing, contact your dealer, distributor or courier company to have them replaced before starting this installation.

Page 13

Maintenance And Service

Loosen

Tighten

Conversion Kit Installation:

1. Turn control knob on the gas valve to the “OFF” position and shut the gas supply off at the shut-off

valve upstream of the unit. CAUTION: The gas supply must be shut off prior to disconnecting the electrical power and before proceeding with the conversion. Allow the valve and unit to cool down to room temperature.

2. Remove the glass door as shown in the

MaIntenance anD serVIce - Glass Door reMoVal.

3. Carefully remove the log set and re grate.

4. Remove the burner as shown in the

MaIntenance anD serVIce - Burner reMoVal.

5. Convert the burner orice(s):

a) Remove the main burner orice with a ½ inch deep socket.

b) Put a bead of pipe-thread sealant or approved Teon tape on the orice threads before installing

into the brass elbow.

c) Install the new orice(s) from the kit into the brass elbow.

6. Convert the pilot injector:

a) Pull the pilot hood straight up to access the pilot injector.

b) Using a

/32” or 4 mm Allen key, remove the pilot injector.

c) Install the new pilot injector supplied with this conversion kit. Simply

screw the new injector inside the pilot hood using the Allen key,

d) Reinstall the hood by placing the hood on the assembly, line up the key

way, and snap into place.

7. Convert the SIT gas valve:

a) Remove the black protection cap from the HI/LO knob by hand shown in

Figure 11.

b) Insert a 5/32” or 4 mm Allen wrench into the

Figure 11: Removing

valve cap.

hexagonal key-way of the screw (see Figure 12), rotate it counter-clockwise until it is free and extract it.

c) Check that the screw is clean and if necessary

d) Flip the screw (refer to Figure 13).

e) Using the Allen wrench as shown in Figure 12,

f) Verify that if the conversion is from NG to

Figure 12: Removing valve

screw.

remove dirt.

rotate the screw clockwise until a torque of 9 inch lbs. WARNING! Do not over tighten the screw. It is recommended that you grip the wrench by the short side.

LPG, the screw must be re-assembled with the red o-ring visible (refer to Figure 14). If the conversion is from LPG to NG, the red o-ring of the screw must be not visible.

Figure 13: Flip valve

screw.

Page 14

Maintenance And Service

Red o-ring

is not visible

Red o-ring

is visible

LPG Configuration

Figure 14: O-ring on valve screw.

8. Reinstall the burner, re grate, log set, and glass door. Also refer to seconDary InstallatIon - FIre Grate anD loG set InstallatIon in your Owner’s Manual. When re-installing the burner, ensure that the burner to pilot hood and shield relationship is similar to what is shown in Figure 15.

9. Reconnect the main gas line if it was disconnected and open the shut-off valve at the gas line to the unit.

g) Re-attach the black protection

cap that was removed in step a (Figure 11).

10. Use a small brush to apply a warm soapy water solution to all gas connections (use a half dish soap and half warm water). If a gas leak is present, bubbling will occur. Gas leaks can be repaired by using an approved pipe thread sealant or approved Teon tape. NEVER USE AN OPEN FLAME WHEN TESTING FOR LEAKS.

Figure 15. Pilot assembly

beside the burner.

11. Reconnect the electrical power to the unit.

12. Relight the pilot and conrm the ame properly covers both the thermocouple and thermopile (see Figure 4, page 8). Should the pilot require adjustment, turn the adjustment screw (gure 42, page

35) clockwise to decrease or counterclockwise to increase until the correct ame is achieved.

13. Relight the main burner in both the “HI” and “LO” positions to verify proper burner ignition, operation and proper ame appearance. Conrm the inlet and manifold pressures are within the acceptable ranges as directed in section

IntIal IntallatIon - Gas lIne connectIon anD testInG. If the Q1 has

been installed at an altitude higher than 2000ft (610m) it is required to de-rate the unit accordingly:

In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas

In Canada: When the appliance is installed at elevations above 4500 feet (1372 m), the certied high

altitude rating shall be reduced at the rate of 4% for each additional 1000 feet (305 m).

14. MAKE SURE that the conversion label is installed on or close to the rating label to signify that the unit has been converted to a different fuel type.

Page 15

Initial Installation

35 1/4"

(895mm)

25 1/4"

(641mm)

15 1/8"

(384mm)

6 15/16"

(176mm)

Gas

Inlet

3 11/16 "

min

(94mm)

Rear Vent

Top

Vent

41"

(1041mm)

QUALIFIED INSTALLERS ONLY

intRoDuction:

This section of the owner’s manual is for the use of qualied technicians only. Fireplace placement, hearths, facing, mantels, and venting terminations will be covered, as well as the gas and electric systems. There are several installation safety guidelines that must be adhered to. Please carefully read the safety precautions at the front of this manual.

NOTE: The Q1L comes as a top vent unit but can be converted to a rear vent.

Warning: Clearances must be sufcient to allow access for maintenance and service.

PLacement anD fRaming:

Table 2. Framing Dimensions.

Firebox Framing Depth 15⅛” 38.4 cm Width 25¼” 64.1 cm Height - Rear Vent 35¼” 89.5 cm Height - Top Vent 41” 104.1 cm Gas Inlet (Distance

From Back)

The location for the replace can be along a wall, raised or at oor level, or in a corner. There are specic framing measurements for each situation. The basic opening should have the dimensions shown in Figure 16. The replace must have a strong and level surface to be placed on. The surface should be made of wood or a non-combustible material, not carpet. The framing boards may touch the top and back standoffs, but only the

supplied insulating material can be placed between the frame and

Figure 16. Dimensions for Framing the Firebox

Brought to the left side of the replace. The location should be chosen so the replace will be at least 36 inches (91.4 cm) from drapes, doors and other combustibles. The framed opening should also be a minimum of 3 11/16” inches (9.4 cm) from the nearest perpendicular wall (sidewall to the edge of the opening).

the standoffs.

The gas line, ⅜ inch NPT, should be

Page 16

Initial Installation

QUALIFIED INSTALLERS ONLY

ReaR vent conveRsion:

For smaller openings the Q1L can be converted from a top vent to a rear vent unit.

Vent Collar

Base Plate

Step 1: Using a T20 screwdriver

Exhaust Spigot

Cover Plate

remove the vent collar, base plate, cover plate and exhaust spigot (28 screws total) as shown in Figure 17.

Figure 17. Vent Conversion - Step 1

Step 2: Switch the removed parts

around as shown in Figure 18 and re-install all 28 screws. To correctly install the base plate keep the locating notch on each side at the bottom. Also note the exhaust spigot uses a lower set of holes when setup as a rear vent.

Use lower set of

holes

Locating Notch

Figure 18. Vent Conversion - Step 2

Page 17

Initial Installation

QUALIFIED INSTALLERS ONLY

insuLating mateRiaL:

Depending on the chosen vent conguration, either one or both pieces of insulating material supplied with the unit are required for correct installation.

Rear Vent: When using the rear vent conguration both the ceramic board and berglass insulation are required. Place the ceramic board on top of the unit rst and then place the insulation on top of the ceramic board as shown in Figure 19.

Top Vent: When using the top vent conguration only the gerglass insulation is required. Cut a notch in the insulation, to t around the vent collar, and place on top of the unit as shown in Figure 20.

Fiberglass Insulation

Ceramic

Board

Figure 19. Unit Insulation - Rear Vent

Fiberglass

Insulation (cut around vent collar)

Figure 20. Unit Insulation - Top Vent

Page 18

Initial Installation

QUALIFIED INSTALLERS ONLY

stanDoffs:

The Q1L is supplied with two sets of standoffs that serve as a framing guide and must be used when the unit is being installed as a replace. The front set of standoffs mount to sides of the unit (see Figure 21)

and can be adjusted as needed to account for the thickness of the wall material. The rear standoffs attach to the back corners of the unit and are not adjustable.

Combustible material can touch the standoffs but must not encroach past them. If

Mounting Screw

Rear Standoff

Mounting Screw

the Q1L is being installed into a pre-existing masonary replace it is not necessary to use the standoffs. Installation of the standoffs will require a T20 screwdriver. Remove the installed screws in the noted locations, place the standoff over the holes, and re-install the screws.

Figure 21. Standoff Mounts

Frame up to this

ange

Multiple Holes for Adjustable

Depth

Front Standoff

No Combustible

Material within

dotted lines

Figure 22. Area created by stanoffs

Page 19

Initial Installation

3 4

(260mm)

1 4

(641mm)

7 8

(562mm)

3 4

(203mm)

7 8

(1123mm)

1 2

(794mm)

Outside Wall

Inside Wall

3 4

(260mm)

1 4

(641mm)

1 2

(1003mm)

7 8

(709mm)

7 8

(1123mm)

3 4

(203mm)

Outside Wall

Inside Wall

QUALIFIED INSTALLERS ONLY

coRneR instaLLation:

The dimensions for installing a replace in the corner of a room are given in Figures 23 and 24. Refer to “InItIal InstallatIon - allowaBle co-axIal Vent conFIGuratIons” for allowable pipe lengths.

Do not interfere with the structural integrity of the walls.

Figure 23. Dimensions for a corner installation, rear

vented.

Figure 24. Dimensions for a corner installation, top

vented.

Page 20

12" (305 mm) Mantle

1¼” (32mm)

thick non-

combustible

floor

12" (305 mm) minimum from wall

If hearth is flush with flooring

2" (51 mm) Mantle

41"

(1041 mm)

minimum

from bottom

of unit

35"

(889 mm)

minimum

from bottom

of unit

10” (254 mm)

Non-Combustible

Facing

7" (178 mm) minimum from side of door to

side wall

1/2” (12.7mm)

thick non-

combustible facing

Initial Installation

QUALIFIED INSTALLERS ONLY

mantLe & non-combustibLe cLeaRances:

When installing the Q1 as a zero clearance replace the correct clearances and materials must be used:

above unit: A minimum 10” of ½” thick non-combustible facing material, with a R-Value no less than

0.26, must be used (see Figure 25).

in fRont of unit: A minimum 12” of 1¼” thick non-combustible material, with a R-Value no less than

2.27 (K-value no less than .55), must be used when the unit is either sitting on the oor or raised within 2’’ of the oor. Approved 1” thick Q1 oor protection is available separately under part number 50-3016. When raising the unit 2” - 4” above the oor a minimum 12” of ¾” thick material, with a R-Value no less than 1.36 (K-value no less than .55), must be used. If raising the unit higher than 4” from the oor, any combustible oor material may be used.

aDjacent/siDewaLL: There must be a minimum distance of 7” from the side of the rebox door to an adjacent wall composed of combustible material (see Figure 25).

mantLe: It is not necessary to install a mantle, but if one is desired the guidelines as shown in Figure 25 below must be followed.

Figure 25. Non-Combustible Clearances

Page 21

Initial Installation

QUALIFIED INSTALLERS ONLY

DiRect vent:

WARNING: This appliance has been designed to draw room air for proper heat circulation from the bottom of the unit, and out the top front. Blocking or modifying these openings in any way can create hazardous situations.

The vent length for the Q1L must be between 7” (18 cm) and 44ft (13.4 m). This model is vented with co-axial 4” intake, 6 5/8” exhaust aluminum or stainless steel approved rigid vent leading into a vertical or horizontal termination cap. The ue collar of this model will t inside of a standard 4” x 6 5/8” vent and must be either correctly interlocked or fastened, with three screws directly to the vent.

The Q1L may also be converted to a replace insert with the use of a co-linear vent adapter kit (50-

2982) see InItIal InstallatIon - co-lInear VentInG aDaPter KIt. When converted to co-linear venting the lenth of vent must be between 8’ (2.44m) and 40’ (12.19m). The insert model is vented with a 3” intake and a 3” exhaust aluminum or stainless steel approved ex vent leading into a vertical termination cap only. The ue collars of this model will t inside of a standard 3” vent and must be fastened directly to the vent with three screws. The exhaust vent and air intake are both located on the top of the unit.

Check periodically that the vents are unrestricted. Also ensure that all direct vent pipes have been properly sealed and installed after routine inspection or cleaning. The air intake and exhaust pipes must be installed in the correct locations on the top of the Q1L.

venting fiRePLace inseRts:

When using the co-linear venting adapter kit (50-2982) the Q1L may be installed and vented into any solid fuel replace that has been installed in accordance with the National, Provincial/State and local building codes and has been constructed of noncombustible materials. Please reference the information in Table 8 and Figures 38. An approved chimney liner and rain cap must be used. A throat connector or ashing must be installed to ensure a tight seal, top performance, safety and efciency. Carefully follow the manufacturer’s instructions that accompany the chimney liner kit. Use double walled aluminum ex vent (3” ex conversion piece and 4”x 6 5/8” cap) from the following approved products; Simpson Dura-Vent (Direct Vent GS). If necessary, remove the vent collar plate from the top of the insert and connect it securely to the liner with sheet metal screws. Check for any tears in the liner at this point. IMPORTANT: The screws that hold the vent collar plate in its approved position must be installed.

NOTE: If the Q1L unit is pulled out of its installation, and the vent-air intake system is disconnected for any reason, ensure that the vent-air intake pipes are re-sealed with high-temperature sealant and reconnected with three (3) sheet metal screws evenly spaced.

Page 22

Initial Installation

QUALIFIED INSTALLERS ONLY

vent teRmination RestRictions:

Fixed

Closed

Openable

Fixed

Closed

Termination Cap

Figure 26. Vent Termination Restrictions, refer to Table 3.

Letter Canadian Installation

A 12 in (30 cm) Clearance above grade, verandah, porch, deck, or balcony.

B 12 in (30 cm) 9 in (23 cm) Clearance from window or door that may be opened.

C 12 in (30 cm)* Clearance from permanently closed window (to prevent

D 24 in (60 cm)* Vertical clearance to ventilated soft located above the

E 18 in (45 cm)* Clearance to unventilated soft.

F 12 in (30 cm)* Clearance to outside corner.

G 12 in (30 cm)* Clearance to inside corner.

H 3 ft (91 cm) within a height of

15 ft (4.5 m) above the meter/

regulator assembly

I 3 ft (91 cm) 3 ft (91 cm)* Radial clearance around service regulator vent outlet.

J 12 in (30 cm) 9 in (23 cm) Clearance to non-mechanical air supply inlet to building, or

K 6 ft (1.83 m) 3 ft (91 cm) above if within 10

L 7 ft (2.13 m

M 12 in / 30 cm

N 12 in (30 cm)* Clearance horizontally to any surface (such as an exterior

O 12 in (30 cm) Clearance above roof line for vertical terminations.

Air Supply Inlet

Gas MeterG

Restriction Zone

(Termination not allowed)

Table 3: Vent termination clearances.

US Installation

3 ft (91 cm) within a height of

15 ft (4.5 m) above the meter/

regulator assembly*

ft (3 m) horizontally

7 ft (2.13 m)

12 in / 30 cm*

condensation).

terminal, within a horizontal distance of 2 ft (60 cm) from center line of terminal.

Clearance to each side of center line extended above meter/regulator assembly.

the combustion air inlet to any other appliance.

Clearance to mechanical air supply inlet.

Clearance above paved sidewalk or paved driveway located on public property.

Clearance under verandah, porch, deck, or balcony.

wall) for vertical terminations.

Description

In accordance with the current CSA B149, Natural Gas and Propane Installation Code.

In accordance with the current ANSI Z223.1 NFPA 54, National Fuel Gas Code.

* These numbers are only estimates. t

A vent shall not terminate directly above a side walk or paved driveway that is located between two single family dwellings

and it serves both dwellings. +

Permitted only if verandah, porch, deck, or balcony is fully open on a minimum of two sides beneath the oor.

Clearances are in accordance with local installation codes and the requirements of the gas supplier.

NOTE: Venting terminals shall not be recessed into walls or siding.

Page 23

Initial Installation

Framing

Joists/Studs

10”

QUALIFIED INSTALLERS ONLY

venting cLeaRances:

A 1” (25 mm) clearance to combustibles must be maintained around any vertical vent pipe. Around a horizontal vent pipe, the clearance to combustibles should be 2” (51 mm) above and 1½” (38 mm) on the sides and bottom. When combustible materials are directly above a 90° elbow, 3” (76 mm) of clearance are necessary.

Table 4. Vent Pipe Minimum Clearances.

Vertical Pipe to

the Side Walls

Hard

Pipe

1”

(25.4 mm)

A 10” (254 mm) x 10” (254 mm) frame (see Figure 27) will assure the proper support and spacing for the vent pipe as it passes through the wall. Installations in Canada require that a wall thimble be used for passing through walls and ceilings. All sealing and vapour barriers must comply with local building codes.

The conguration of the venting pipes depends on the locations of walls, ceilings, and studs. However, the pipes cannot be of arbitrary length and arrangement. Because the length of the vertical and horizontal sections dramatically affects the burning efciency of the replace, certain guidelines have been set in

InItIal InstallatIon - allowaBle co-axIal Vent conFIGuratIons.

Venting terminals can not be recessed into a wall or siding.

Horizontal Pipe to

the Sides & Bottom

1½”

(38.1 mm)

Above an Elbow

Above the Unit

3”

(76.2 mm)

Above an Elbow

Not Above the Unit

3”

(76.2 mm)

Above Horizontal

Vent Pipe

2”

(51 mm)

Wall Frame 8”

(203mm) or less

10”x10”

(25x25cm)

WARNING: This gas appliance must not be connected to a chimney ue serving a separate solid-burning appliances.

Figure 27. Vent Framing For Wall or Ceiling.

aPPRoveD venting PaRts:

Table 5: Approved Vent Manufacturers

Manufacturer Trade Name Nominal Sizes

American Metal Products AmeriVent Direct 4” - 6 5/8” ICC EXCELDirect 4” - 6 5/8” Security Chimneys International LTD Secure Vent 4” - 6 5/8” Selkirk Metalbestos Direct-Temp 4” - 6 5/8” Simpson Dura-Vent Direct Vent GS 4” - 6 5/8”

The Q1L replace has been tested and certied for use with AMERICAN METAL PRODUCTS “AMERIVENT DIRECT”, SIMPSON DURAVENT TYPE GS PIPE FOR GAS STOVES. SECURITY CHIMNEY’S “SECURE VENT DIRECT VENT SYSTEM” and SELKIRK “DIRECT-TEMP VENT SYSTEM” kits are available for horizontal and vertical venting. When using Simpson Duravent, it is recommended that, before installation, a bead of RTV High Temperature Silicone should be applied to each outer vent joint, and Mil-Pac to each inner joint. When planning an installation, it will be necessary to select the proper length of vent pipe for the particular requirements.

WARNING: Do not mix parts from different vent manufacturers’ systems.

Page 24

Initial Installation

QUALIFIED INSTALLERS ONLY

EXCEPTION TO WARNING: This product has been evaluated by Intertek for using a Direct Vent GS starting collar in conjunction with Secure Vent, Direct-Temp, AmeriVent Direct, and EXCELDirect venting systems. Use of these systems with the Direct Vent GS starting collar is deemed acceptable and does not affect the Intertek WH listing of the appliance.

Table 6: Vent part numbers (Must state if galvanized or black wanted, PART NUMBERS).

Direct Vent GS Direct-Temp Secure Vent Ameri Vent Direct Description

908 4DT-6 SV4L6 6” pipe length

4D7 7” pipe length

907 4DT-9 9” pipe length

906 4DT-12 SV4L12 4D12 12” pipe length

904 4DT-24 SV4L24 4D2 24” pipe length

903 4DT-36 SV4L36 4D3 36” pipe length

902 4DT-48 SV4L48 4D4 48” pipe length

945 4DT-EL45 SV4EBR45 4D45B 45° elbow, black

990 4DT-EL90 SV4EBR90 4D90B 90° elbow, black

950 4DT-VS SV4VS Vinyl siding standoff/sheild

942 4DT-WT SV4RSN 4DWT Wall thimble

953 4DT-SC SV4FC 4DSC Storm collar

963 4DT-FS SV4BF 4DFSP Fire stop

988 4DT-WS/B SV4BM 4DWS Wall strap/support/band

970 4DT-HKA SV0SHK 4DHTK1

911 11” to 14 ⅝” pipe, adjustable

4DT-AJ 4D12A 4” to 10” pipe , adjustable

SV4LA12 1½” to 12” pipe , adjustable

943 4DT-AF6 4DF Flashing, 0/12 to 6/12 roof pitch

943S 4DT-AF12 4DF12 Flashing, 7/12 to 12/12 roof pitch

SV4FA Flashing, 1/12 to 7/12 roof pitch

SV4FB Flashing, 8/12 to 12/12 roof pitch

943F SV4F Flat ashing

991 4DT-HVC High wind vertical termination

985 4DT-HHC High wind horizontal termination

Horizontal termination kit (SD: Basic Kit, SEL: Kit A, SC: Standard Kit)

978 4DT-VKC SV0FAK 4DVTK Vertical termination kit

971 4DT-HKB SV0SHK2 4DHTK2

Horizontal termination kit (SD: Kit A, SEL: Kit B, SC: Kit)

Page 25

Initial Installation

QUALIFIED INSTALLERS ONLY

hoRizontaL teRmination - ReaR vent with no veRticaL Rise:

The Q1L can be installed in rear vent applications with no vertical rise within the parameters as shown in Figures 28 and 29.

Approved horizontal termination

18” (46 cm) Max. vent length

Approved through wall thimble

Figure 28. Corner Rear Vent - No Vertical Rise

Max. 1 x 45˚ Elbow

7” (18 cm) Min. vent length

24” (61 cm) Max. vent length

Approved horizontal termination

Figure 29. Flat to Wall Rear Vent - No Vertical Rise

Approved through wall thimble

Page 26

1 2 3 4 5 6 7 8 9 10 11 12 13 14

HORIZONTAL RUN

VERTICAL RISE

INSTALLATION

PROHIBITED

INSTALLATION

PROHIBITED

Initial Installation

HORIZONTAL RUN

QUALIFIED INSTALLERS ONLY

aLLowabLe co-axiaL vent configuRations:

Figures 30a & b show the range of possible vent con gurations if the unit is top or rear vented, for vertical and horizontal terminations. Any layout that remains within the shaded areas is acceptable. Having the fewest number of elbows is ideal, as they tend to disrupt air movement. Using 45˚ elbows is preferable to using 90˚ elbows. Also, a shorter vent system will perform better than a longer one. When top vented, the total length of horizontal vent pipe can not exceed 14 feet (4.27m) and the total vent length can not exceed

44ft (13.4m). Any combination of rise and run can be used as long as it lays within the

Figure 30a. Possible Vent Con gurations for Top

Vented Vertical and Horizontal Terminations.

shaded area (a total of two (2) 90˚ elbows or four (4) 45˚ elbows can be used. In addition to what is shown, if a 90˚ elbow is used in the horizontal plane, 3 feet (91.4cm) must be subtracted from the allowable horizontal run (for each 45˚ elbow, 1½ feet must be subtracted).

Note: Air restrictors (supplied with the unit) are required for vertical venting runs of 8ft (2.44m) or taller. See

aIr restrIctor

settInGs for more information

Note: Minimum length of co-linear venting is 8ft (2.44m) and maximum length is 40ft (12.19m)

INSTALLATION

PROHIBITED

VERTICAL RISE

1 2 3 4 5 6 7 8 9

1 2 3 4 5

HORIZONTAL RUN

Figure 30b. Possible Vent

Con gurations for Rear Vented Vertical

and Horizontal Terminations.

Page 27

Initial Installation

QUALIFIED INSTALLERS ONLY

co-LineaR venting aDaPteR Kit (50-2982):

The Q1L can be converted from solid co-axial venting to 3” (76mm) exible co-linear venting to allow for installation into exisiting masonary replaces (see Figures 31-33). Co-linear venting can not be used in combustible chimney installations. This adapter kit is for vertical terminations only and can’t be connected to a chimney ue serving a seperate solid-fuel burning stove or appliance.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specically approved with this appliance may result in property damage or personal injury.

Adapter Kit Contents:

Vent Plate Adapter

Ceramic Gasket

3” Dia. Exhaust

Spigot

Exhaust Spigot

Ceramic Flange

Gasket

Exhaust Spigot

Ceramic Tube

Gasket

Figure 31: Co-Linear Venting Kit Contents

Page 28

Initial Installation

Adapter Kit Installation:

QUALIFIED INSTALLERS ONLY

Vent Collar

Base Plate

4” Exhaust Spigot

Cover Plate

Figure 32: Removal of Co-Axial Venting

Vent Plate Adapter

3” Exhaust Spigot

Step 1: Using a T20 screwdriver

remove the vent collar, base plate, cover plate and 4” exhaust spigot (28 screws total) as shown in Figure 32. The vent collar, base plate, and 4” exhaust spigot will no longer be used.

Figure 33: Installation of Co-Linear Vent Kit

Cover Plate

Step 2: Install the components

supplied in the adapter kit as shown using the screws that had been removed from the unit in Step 1. The gasket on the bottom side the vent plate adapter and exhaust spigot ange gasket will be sandwiched together when properly installed.

Page 29

Initial Installation

QUALIFIED INSTALLERS ONLY

aiR RestRictoR settings:

When installing the Q1L with 8ft (2.44M) or more of vertical venting, either co-axial or co-linear, it may be necessary to restrict the fresh air supply in the rebox to control the combustion and ame appearance. Using the pair of air restrictors supplied with the unit, install them on each side of the rebox and adjust to the correct setting as outlined in the gure and table below. To install the air restrictors rst you must remove the log set, air diffuser, and creamic brick panels (see seconDary InstallatIon - oPtIonal PorcelaIn Panels InstallatIon anD reMoVal) then remove the set screws as shown on each side of the rebox. Next, install the restrictors at the correct setting and tighten the set screws to hold them in place.

Set Screw

Figure 34: Installation of Air Restrictors

Table 7: Air Restrictor Settings

Air Restrictor Settings

Length of Vertical Vent Propane Natural Gas

Less than 8ft (2.44m) co-linear or co-axial No Restriction Required No Restriction Required

8ft (2.44m) - 20ft (6.1m) co-linear or co-axial No Restriction Required No Restricition Required

Through Roof Termination, more than 20ft (6.1m) to 40ft (12.19m) co-linear

Through Roof Termination, more than 20ft (6.1m) to 40ft (12.19m) co-axial

Setting #2 Setting #3

Setting #1 Setting #1

Page 30

Initial Installation

QUALIFIED INSTALLERS ONLY

hoRizontaL teRmination:

NOTES:

1. Horizontal pipes must not be level. For every 12 inches (305 mm) of horizontal travel (away from the stove), there should be at least ¼ inch (6.4 mm) of vertical travel. Never allow the vent to run downward, as this could cause high temperatures or even present the possibility of a re.

2. The exterior of the horizontal vent termination must not be blocked or obstructed.

3. If the vent termination is not being attached to wood, the four wood screws provided should be replaced with material appropriate fasteners.

4. For buildings with vinyl siding, a vinyl standoff should be

Elbow

installed between the vent cap and the exterior wall. Attach the vinyl siding standoff to the horizontal termination. Note that the termination bolts onto the at portion of the standoff, providing an air space between the wall and the vent termination. The air gap prevents excessive heat from possibly melting the vinyl siding.

5. Horizontal pipes must be supported every 3 feet (914

mm). Plumber’s all round strap will sufce.

Wall thimble fire stop

Exhaust pipe

Combustion air outer pipe

Figure 35. Horizontal Vent Termination

Horizontal wall termination

Wall framing

6. When running horizontal pipe, clearances to combustibles must be maintained 1½ inches (38 mm) sides, 1½ inches (38 mm) bottom, and 2 inches (51 mm) top.

Step 1. Set the replace in the desired location. Check to determine if wall studs will be in the way when

the venting system is attached. If this is the case, the location of the replace may have to be adjusted or the venting may have to be offset.

Step 2. Direct vent pipe sections are designed with special twist-lock connections. Dry t the desired

combination of pipe and elbows to the appliance adaptor.

Step 3. With the pipe in the correct position and attached to the replace, mark the wall for a 10 inches

(25.4 cm) x 10 inches (25.4 cm) square hole (see Figure 27). The center of the hole should match the center line of the horizontal pipe. Cut and frame the hole in the exterior wall where the vent will be terminated. If the wall being penetrated is made of a non-combustible material (i.e. masonry or concrete) a 7 inches (17.8 cm) hole is acceptable.

Page 31

Initial Installation

QUALIFIED INSTALLERS ONLY

NOTE: For Simpson Duravent only, place a bead of Mil-Pac or Rutland No 78 Stove and Gasket Cement on the outer edge of the inner exhaust pipe (non-ared end). Push the pipe sections together, then twist about ¼ turn, making sure the two sections are fully locked. Wrap all seams with foil ducting tape.

Step 4. With the hole now framed, the wall thimble installed, and the pipe extending into the wall,

proceed to the outside. Attach the termination to the pipe using RTV and Mil-Pac or Rutland No 78 Stove and Gasket Cement to seal joints. The vent pipe must extend into the vent cap at least 1¼ inches (3.2 cm). Secure the connection between the vent cap and the pipe by attaching the two (2) sheet metal straps, which extend from the vent cap assembly to the outer wall of the vent pipe. Bend any remaining portion of the strap back towards the vent cap. Security Secure Vent uses a twist lock cap.

Step 5. Position the horizontal vent termination in the center of the 10 inches (25.4 cm) square hole

and attach to the exterior wall with the four screws provided. The arrow on the vent termination should be pointing up. Run a bead of non-hardening mastic around the edges of the vent cap, to make a seal with the wall. Ensure the proper clearances to combustibles have been maintained.

veRticaL teRmination:

Step 1. Check the instructions for required clearances (air spaces) to combustibles when passing

through ceilings, walls, roofs, enclosures, attic rafters, or other nearby combustible surfaces. Do not pack air spaces with insulation.

Step 2. Set the gas appliance in the desired location. Drop a plumb bob down from the ceiling to

the position of the appliance ue exit, and mark the location where the vent will penetrate the ceiling. Drill a small hole at this point. Next, drop a plumb bob from the roof to the hole previously drilled in the ceiling, mark the spot where the vent will penetrate the roof. Determine if ceiling joists, roof rafters, or other framing will obstruct the venting system. You may wish to relocate the appliance, or to offset, to avoid cutting load bearing members.

Step 3. To install the Round

Support Box/Wall Thimble

Vertical

Termination

in a at ceiling, cut a 10 inch (25.4 cm) square hole

Elbow Strap

Storm Collar

in the ceiling, centered in the hole drilled in Step 2.

Flashing

Frame the hole as shown in Figure 27.

Roofing nails

Step 4. Assemble the desired

lengths of black pipe and elbows necessary to reach from the appliance adapter up through the Round Support Box. Insure that all pipe and elbow connections are in their fully twist-locked position.

Figure 36. Vertical Vent Termination

Page 32

Initial Installation

Dimension ‘H’ obtained from table below.

QUALIFIED INSTALLERS ONLY

STEP 5. Cut hole in the roof centered on the small hole placed in the roof from Step 2. The hole should

be of sufcient size to meet minimum requirements for Clearance to Combustibles, as specied. Continue to assemble lengths of pipe and elbows necessary to reach from the ceiling support box up through the roof line. Galvanized pipe and elbows may be utilized in the attic, as well as above the roof line. The galvanized nish is desirable above the roof line, due to the higher corrosion resistance.

STEP 6. Once the pipe sections have been joined, and run up through the hole in the roof, slip an elbow

strap over the exposed sections, bend the support straps outwards, and push the elbow strap down to the roof level, as shown in Figure 36. Tighten the clamp around the pipe section. Use a level to make sure the pipe is truly vertical. With roong nails, secure the support straps to the roof. Seal the nails holes heads with non-hardening mastic. Trim the excess length of the support straps that extend out beyond the edge of the ashing.

STEP 7. Slip the ashing over the pipe section protruding through the roof. Secure the base of the

ashing to the roof with roong nails. Use a non-hardening sealant between the uphill edge of the ashing and the roof. Insure the roong material overlaps the top edge of the ashing. Verify that you have at least the minimum clearance to combustibles at the roof line.

STEP 8. Continue to add pipe sections until the height of the vent cap meets the minimum code

requirements. Refer to Figure 37 and Table 8. Note that for steep roof pitches, the vent height must be increased. In high wind conditions, nearby trees, adjoining roof lines, steep pitched roofs, and other similar factors can result in poor draft, or down drafting. In these cases, increasing the vent height may solve the problem.

STEP 9. Slip the storm collar over the pipe, and push it down to the top of the roof ashing as shown

in Figure 37. Use the non-hardening sealant around the joint between the pipe and the storm collar.

STEP 10. Twist-lock the vent cap.

Table 8: Minimum ‘H’ for Figure 35.

Roof Pitch Minimum Height (H)

Feet Meters

Flat to 7/12 1 0.3

Over 7/12 to 8/12 1.5 0.46

Over 8/12 to 9/12 2 0.61

Over 9/12 to 10/12 2.5 0.76

Over 10/12 to 11/12 3.25 0.99

Over 11/12 to 12/12 4 1.22

Over 12/12 to 14/12 5 1.52

Over 14/12 to 16/12 6 1.83

Figure 37: Height of Vertical Termination;

Reference Table 8.

Over 16/12 to 18/12 7 2.13

Over 18/12 to 20/12 7.5 2.29

Over 20/12 to 21/12 8 2.44

Page 33

plumber’s tape connected to wall strap

Wall strap

45° elbows (x2)

Initial Installation

QUALIFIED INSTALLERS ONLY

NOTES:

(1) If an offset is necessary in the attic to avoid

obstructions, it is important to support the vent pipe every 3 feet (914 mm), to avoid excessive stress on the elbows, and possible separation. Wall straps are available for this purpose (see Figure 38).

(2) When ever possible, use 45° degree elbows instead

of 90° degree elbows. The 45° degree elbow offers less restriction to the ow of ue gases and intake air.

(3) For multi story installations; a ceiling restop is

required at the second oor, and any subsequent oors (see Figure 39). The opening should be framed to 10” (254 mm) x 10” (254 mm) inside dimensions, in the same manner as shown in Figure

40.

(4) Any occupied areas above the rst oor, including

Figure 38: Use of Wall Straps.

closets and storage spaces, which the vertical vent passes through, must be enclosed. The enclosure may be framed and sheet-rocked with standard building materials. However consult the appliance manufactures installation instructions for the minimum allowable clearance between the outside of the vent pipe, and the combustible surfaces of the enclosure. Do not ll any required air spaces with insulation.

Figure 39: Multi-Story Vent Pipe Installation.

Page 34

Initial Installation

The total vent length must be between 8 ft (2.44 m) and 40 ft (12.19 m).

Install a sealed vent cap to prevent leakage of room air up through chimney.

The intake and the exhaust are 3" (76mm).

Measure the height of the chimney beforehand and purchase the appropriate venting. Never attempt to over-stretch a flexible liner to accommodate the height of the chimney. Every joint in the venting must be secured with three (3) #8 x 3/8” HWH sheet metal screws and an appropriate sealant (either silicone or stove cement).

The flue damper can be fully blocked open or removed for installation of the unit; the smoke shelves, shields and baffles may be removed if attached by mechanical fasteners.

The fireplace and fireplace chimney must be clean, in good working order and constructed of non-combustible materials.

Make sure that all chimney cleanouts are tight fitting and will not permit air to leak into the chimney.

Refractory, glass doors, screen rails, screen mesh and log grates can be removed from the fireplace before installing the unit.

WARNING: This fireplace has been converted

for the use with a gas fireplace insert only and

cannot be used for burning wood or solid

fuels unless all original parts have been

replaced, and the fireplace re-approved by the

authority having jurisdiction.

C-11168

QUALIFIED INSTALLERS ONLY

soLiD fueL fiRePLace instaLLation:

Table 9: Min. Fireplace Dimensions

Width Height Depth

Fireplace Dimensions 20¼” (51.4 cm) 27½” (69.8 cm) 12½” (31.7 cm)

Note: Space must be left for gas line on left side of unit for servicing purposes

The base, sidewalls and top structure of the solid fuel rebox cannot be altered with the exception of: removal of dampers, removal of smoke shelf or bafe, removal of ember catches, removal of log grate, removal of viewing screen/curtain, and removal of doors. THE ORIGINAL FIREPLACE MAY NEVER BE RETURNED TO SOLID FUEL USE IN THIS CONDITION.

Figure 40: Solid Fuel Fireplace Installation.

IMPORTANT: If the factory-built replace has no gas access hole(s) provided, an access hole of 1.5 inch (37.5 mm) or less may be drilled through the lower sides or bottom of the rebox in a proper workmanship like manner. This access hole must be plugged with non-combustible insulation after the gas supply line

has been installed. Cutting any sheet-metal parts of the replace, in which the gas replace insert is to be installed is prohibited. The label plate shown on the right, included with co-linear venting adapter kit, must be permanently attached inside the cavity of the replace in a visible location.

Figure 41: Fireplace Altered Plate.

Page 35

Initial Installation

QUALIFIED INSTALLERS ONLY

gas Line connection anD testing:

WARNING: Only persons licensed to work with gas piping may make the necessary gas connections to this appliance.

GAS LINE CONNECTION

• This stove is equipped with a certied exible pipe located on the left side of the unit terminating in a 3/8” female NPT tting. Consult your local authorities codes or the CAN/CGA B 149 (1 or 2) installation code in Canada, or in the USA gas installations follow either local codes or the current edition of the National Fuel Gas Code ANSI Z223.1.

• The efciency rating of this appliance is a product thermal efciency rating determined under continuous operating conditions and was determined independently of any installed system.

The appliance and its shutoff valves must be disconnected from the gas supply piping system

Gas Control

Knob

Pilot Adjustment

Screw

during any pressure testing where the pressure exceeds ½ PSIG (3.45 KPa) or damage will occur to the valve.

The appliance must be isolated from the gas supply piping system by closing its individual manual

shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psig (3.45 KPa).

Always check for gas leaks with a soap and water solution after completing the required pressure test.

Inlet

PressureTap

IN OUT

Manifold

PressureTap

Figure 42: Fully Labeled Gas Valve.

TO TEST VALVE PRESSURES

The pressure taps are located on the top right of the valve shown in Figure 42.

•Turn set screw 1 turn counter clockwise to loosen,

•Place

/16” (8 mm) I.D. hose over pressure tap system.

•Check pressures using a manometer.

•When nished, release pressure, remove hose & tighten set screw.

Table 10: Pressure and BTU Information.

TP TH TP TH

Hi/Low

Knob

Main Orice #46 DMS 1.2 mm

Manifold Pressure 3.5” W.C. (0.87 KPa) 10.0” W.C. (2.49 KPa)

Min. Manifold Pressure 1.6” W.C. (0.40 KPa) 6.4” W.C. (1.59 KPa)

Max Supply Pressure 7.0” W.C. (1.74 KPa) 11.0” W.C. (2.74 KPa)

Min. Supply Pressure 4.5” W.C. (1.12 KPa) 10.4” W.C. (2.59 KPa)

Max BTU/hr Input 20,000 BTU/hr (5.86 KW) 18,500 BTU/hr (8.42 KW) Min. BTU/hr Input 13,600 BTU/hr (3.98 KW) 14,500 BTU/hr (4.25 KW)

NEVER USE AN OPEN FLAME FOR LEAK TESTING.

Natural Gas Propane

Page 36

Initial Installation

QUALIFIED INSTALLERS ONLY

eLectRicaL RequiRements:

The fan will not operate if the appliance is cold. Once the unit is lit and the fan is set to the desired level, the fan will automatically turn on upon reaching operating temperature. The fan will automatically turn off after the appliance has cooled down.

The replace must be electrically connected and grounded in accordance with local codes or, in the absence of local codes, with the current CSA C22.1 Canadian Electrical Code Part 1, Safety Standards For Electrical Installations, or The National Electrical Code ANSI / NFPA 70 in the US.

WARNING: The electrical grounding instructions must be followed. The fan kit is equipped with a threeprong (grounding) plug for your protection against shock hazard, and should be plugged directly into a properly grounded three-prong outlet. DO NOT cut or remove the grounding prong from this plug.

CAUTION: When servicing controls, label all wires prior to disconnection. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. If any of the original wire as supplied with the appliance must be replaced, it must be replaced with 18 AWG wire with a temperature rating of 105°C

Figure 42: Fan wiring diagram.

Page 37

Secondary Installation

fiRe gRate anD Log set instaLLation:

The placement of the logs is not arbitrary. If they are positioned incorrectly, the  ames can be “pinched” and will not burn correctly. All of the logs come with either a notch or ledge, which make alignment easier. Using the pictures provided, carefully set the logs in place (see Figures 43 through 47).

NOTE: The logs are fragile and should be handled gently.

Figure 43: This is how the  rebox looks with only the burner, air diffuser, log grate and brick panels in place. The log grate can be easily removed by simply lifting up off the locating screws.

Figure 43. Empty  rebox with grate and locator pins.

Step 1: Place the back log on the top

legde of the air duffuser with back up against the rear brick panel. Install the ember bed assembly into the  rebox as shown, making sure the ember bed is up against the front lip of the  rebox air diffuser (Figure 44)

Figure 44. Back Log and Ember Bed Installation.

Step 2: Fill in the bottom of the  rebox using

the coal nuggets supplied with the unit as shown in Figure 45.

Figure 45. Coal Nuggets Installation.

Page 38

Secondary Installation

Step 3: Install the big y shaped twig on the far left side by locating the bottom of it on the far left log grate upright. The twig should run parallel with the side of the  rebox and the top will rest on the top of the ember bed. Then install the big, slightly curved twig on the far right side by locating the bottom of it on the far right log grate upright. The top will rest on the smooth section of the middle ember bed twig.

Figure 46. Third Stage Log Set Installation.

Step 4: Next, install the second

small twig between the two right side log grate uprights by locating the notch on the bottom side with with cross bar of the log grate. Then install the medium sized straight twig between the center and right side log grate upright by locating the notch on the bottom side with the log grate cross bar. The top of the twig will rest on the middle ember bed twig

Figure 47. Fourth Stage Log Set Installation.

Page 39

Secondary Installation

Step 5: Finally, install the large straight twig between the center and left side log grate upright by locating the notch on the bottom side with the log grate cross bar. The top of the twig will rest on top of the far right curved twig. The last remaining straight twig gets intalled by locating the front in the crook of the far left y shaped twig and the back notch rests on the top edge of the ember bed.

Figure 48. Complete log set-up with embers.

Figure 49: The Q1L burning with a good  ame.

NOTE: While the glass is still removed, it is recommended that the gas line be purged by lighting the pilot.

When lighting the  replace for the  rst time since the log set and embers have been installed/replaced, watch for ignition at ALL the burner ports. If a long delay is noticed, turn the appliance off and wait for it to cool down. Then remove the glass and make sure none of the burner ports are blocked.

Figure 49. Q1L complete log set-up with coal nuggets burning.

Maintenance: Once a year, the logs should be removed and checked for deterioration or large amounts

of soot. A small amount on the bottom side of the logs is normal. Remove and replace the logs in the same manner described above.

If new coal nuggets or logs are required, contact your nearest ENVIRO dealer.

Never operate the  replace with the glass door removed.

Page 40

Secondary Installation

oPtionaL PoRceLain PaneLs (50-2939) instaLLation anD RemovaL:

Turn off the gas control knob and allow the unit to cool.

Please ensure that your porcelain panels have not been damaged.

To Install Panels:

1. Remove the glass door by following the instruction in the “ Glass Door reMoVal” section and remove the log set, log grate and air diffuser as outlined in the previous section.

2. Remove the  rebox baf e by unscrewing the two screws indicated in Figure 50 using a T20

Figure 50. Baf e Screws.

3. Next, remove the top brick panel retainers on each side as shown in Figure 51 using a T20 screwdriver.

screwdriver. Lower the front of the baf e down and then lift it out of the two locating screws at the rear of the  rebox.

MaIntenance anD serVIce -

4. Carefully remove the left, rear, and right brick panels from the  rebox.

5. Install the rear porcelain panel  rst by sitting it on the ledge at the rear of the  rebox (see  gure 52), then follow with the left and right panels.

6. Re-install the brick panel retainer screws and brackets.

7. Re-install the  rebox baf e.

8. Install the top porcelain panel by screwing it to the  rebox baf e as show in Figure 53 using the supplied screws.

9. Re-install the air diffuser, log grate and log set as outlined in the previous section.

10. Re-Install the glass door

Figure 51. Top Panel Retainers.

Figure 52. Rear Panel Ledge. Figure 53. Top Panel Screws.

Page 41

Trouble Shooting

Problem Possible Cause Solution

The main burner does not ignite when called for.

Spark will not light the pilot after repeatedly pressing the spark ignitor.

Pilot will not remain lit. Problem with thermocouple

The gas valve may not be on. • Check that the gas control knob is in the “ON” position. Thermostat is not calling for

heat. Problem with gas valve. • Use a DC voltmeter to measure the voltage across the

Defective piezo ignitor. • Check connections to ignitor.

Broken spark electrode. • Check for broken ceramic insulation, replace electrode if

Misaligned spark electrode. • If spark is not arcing from electrode to pilot, loosen the

circuit.

• Adjust the thermostat several degrees above ambient temperature.

TPTH and TP terminals. Main operator voltage: Open circuit ≥ 325mV Closed circuit ≥ 100mV

• If voltage is not present, check the control circuit for proper operation.

• If proper control system voltage is present, replace the gas control.

• If ignitor connections are good but no spark, replace ignitor.

broken.

screws on the pilot base adjust and tighten.

• Check for proper connection of the thermocouple to the rear of the valve. If loose, fully tighten.

• Check pilot for full ame impingement around thermocouple. If ame is too small, check gas pressure, adjust pilot rate screw, check pilot head for damage.

• Check thermocouple voltage at valve. It must be greater than 5 mV. If low, replace thermocouple.

Air in gas line (pilot dies while knob is depressed).

Burners will not remain lit. Problem with thermopile

circuit.

Flame lifting Leak in vent pipe • Check for leaks in vent connections.

Improper vent conguration • Check vent conguration with manual. Terminal may be recirculating

ue gases

Glass fogs up Normal Condition: after the appliance warms up the glass will clear.

**Due to additives in gas, glass may get hazy during operation** Clean as needed. Blue Flames Normal during start up: ames will yellow as the replace heats up. Flames are burning “dirty” or

sooting

Remote control doesn’t work Problem with the remote • One or more of the batteries are dead. See remote

Flame impingement • Check log positioning.

Problem with replace • The on/off switch is turned to OFF.

• Bleed line.

• Check gas line pressure.

• Contact dealer.

• Check gas line pressure .

• Check for ame impingement on thermopile. If low, see “Pilot will not remain lit”.

• Check thermopile for minimum of 300 mV when burner is switched on.

• Check wiring to thermostat for breaks.

• Check to see if terminal is on correctly.

• May need to install high wind termination cap.

• Contact dealer.

• Increase primary air by opening the venturi shutter and/ or by opening the vent restrictor.

See also “Burners will not remain lit.”

control instructions.

• The gas control valve is turned to PILOT or OFF.

• The pilot has gone out.

Page 42

Parts List

Reference

Number

1 Door Release Tool 50-2510 2 Door Latch Mechanism w/ Spring (set of 2) 50-1285 3 Firebox Air Restrictors (set of 2) 50-2988 4 Log Burner Pilot Shield 50-2991 5 120 Ceramic Fan Temperature Sensor EC-001 6 Convection Fan only 50-2493 7 FPI Fan Controller (69.5V) 115V W/FS Knob EC-039A 8 Fan Controller Knob W/Decal EC-040

9 S.I.T. Piezo Ignitor EC-023 10 FPI Burner Switch EC-026 11 Control Panel w/ Decal 50-2989 12 S.I.T. Pilot Assembly - Standing Pilot 50-2513

- Pilot Assembly Gasket EC-021 13 S.I.T. Nova Valve - Convertible 50-1421 14 Heyco Strain Relief EC-044 15 Domestic Power Cord (115v) EC-042 16 Log Set 50-2935 17 Tube Burner 50-2992 18 Log Grate 50-2997 19 Door Glass w/ Gasket (19.75 x 17.5in) 50-2998 20 Door Complete 50-2990 21 Porcelain Liners Set (4 pieces) 50-2939 22 Ceramic Brick Liner Set (3 pieces) 50-2938

- Ceramic Ledgstone Liner Set (3 pieces) 50-2972

- Fireplace Floor Pad 12” x 20” 50-3016 23 Co-Linear Vent Kit 50-2982 24 Q1L Owners Manual 50-2999

- Q1 Conversion Kit - LP to NG (Nova) 50-2993

- Q1 Conversion Kit - NG to LP (Nova) 50-2983

- 12 oz. Can of Matallic Black Touch Up Paint PAINT-12-MB

Part Description Part Number

Page 43

Parts Diagram

Page 44

Notes

Page 45

Notes

Page 46

Warranty for Enviro Gas Products

Sher wood Industries Ltd. (“Sherwood”) hereby warrants, subject to the terms and conditions herein set forth, this product against defects in material and workmanship during the specified warranty period starting from the date of original purchase at retail. In the event of a defect of material or workmanship during the specified warranty period, Sherwood reserves the right to make repairs or to assess the replacement of a defective product at Sherwood’s factory. The shipping costs are to be paid by the consumer. All warranties by Sherwood are set for th herein and no claim shall be made against Sherwood on any oral warranty or representation.

Conditions

 A completed warranty registration must be submitted to Sherwood within 90 days

of original purchase via the online warranty registration page or via the mail-in warranty registration card provided. Have the installer fill in the installation data sheet in the back of the manual for warranty and future reference.

 This warranty applies only to the original owner in the original location from date of

install.

 The unit must have been properly installed by a qualified technician or installer, and

must meet all local and national building code requirements.

 The warranty does not cover removal and re-installation costs.

 Sherwood Industries Ltd. reserves the right to make changes without notice.

 Sherwood Industries Ltd. and its employees or representatives will not assume

any damages, either directly or indirectly caused by improper usage, operation, installation, servicing or maintenance of this appliance.

 A proof of original purchase must be provided by you or the dealer including serial

number.

Exclusions

An expanded list of exclusions is available at www.enviro.com/help/warranty.html

This warranty does not cover:

 Damage as a result of improper usage or abuse.

 Damage caused from over-firing due to incorrect setup or tampering.

 Damage caused by incorrect installation.

To the Dealer

 Provide name, address and telephone number of purchaser and date of purchase.

 Provide date of purchase. Name of installer and dealer. Serial number of the

appliance. Nature of complaint, defects or malfunction, description and part # of any parts replaced.

 Pictures or return of damaged or defective product may be required.

To the Distributor

 Sign and verify that work and information are correct.

Sherwood Industries Ltd.

6782 Oldfield Road, Victoria, BC . Canada V8M 2A3

Online warranty registration: www.enviro.com/warranty/

Category One Year Two Year Limited Lifetime (7yr)

Parts

(unit serial number required)

Firebox Liner Panels

(excluding porcelain)

Firebox

Heat Exchanger

Burner

Ceramic Logs

Ceramic Glass

Pedestal / Legs

(excluding finish)



Door Assembly

Surround Panels

Exterior Panels

(excluding finish)

Electrical Components

Exterior Surface Finishing

Labour

Whereas warranty has expired, replacement parts will be warrantied for 90 days from part purchase date. Labour not included.

 

Unit serial number required.

Log set and panels excludes wear and tear or breakage caused by cleaning or service.

Glass is covered for thermal breakage. Photos of box, inside of door, and unit serial # must be supplied for breakage due to shipping.

Exterior Surface finishing covers plating, enamel or paint and excludes colour changes, chipping, and fingerprints.

Travel costs not included.



Ceramic Steel

   

  

Up to 5 years



Jan 2013

Page 47

Installation Data Sheet

The following information must be recorded by the installer for warranty purposes and future reference.

NAME OF OWNER:

_________________________________________

ADDRESS:

_________________________________________

PHONE:___________________________________

MODEL:___________________________________

SERIAL NUMBER:___________________________

DATE OF PURCHASE: _____________ (dd/mm/yyyy)

NAME OF DEALER:

_________________________________________

ADDRESS:

_________________________________________

PHONE:___________________________________

NAME OF INSTALLER:

_________________________________________

DATE OF INSTALLATION:___________(dd/mm/yyyy)

� NATURAL GAS (NAT) � PROPANE(LPG)

INLET GAS PRESSURE:_________in wc

MAIN BURNER ORIFICE:__________# DMS

PILOT ORIFICE #_________OR________in diam.

INSTALLER’S SIGNATURE:

_________________________________________

ADDRESS:

_________________________________________

PHONE:___________________________________

MANUFACTURED BY:

SHERWOOD INDUSTRIES LTD.

6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3

www.enviro.com

September 4, 2014

C-14350

Enviro Nova Q1L Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual