WARRANTY REGISTRATION
enviro.com/warranty
C44I
D I REC T VE N T F I R E PL ACE - I P I
OWNER’S MANUAL
WARNING: If the information in this manual is not followed exactly, a
re or explosion may result causing property damage, personal injury
or loss of life. Installation and service must be performed by a qualied
4001609
Version Française: www.enviro.com/fr.html
installer, service agency or the gas supplier.
50-3282
1
Safety Precautions
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
- Do not store or use gasoline or other ammable vapors and
liquids in the vicinity of this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your
building.
• Leave the building immediately.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the re
department.
- Installation and service must be performed by a qualied
installer, service agency or the gas supplier.
INSTALLER:
Leave this manual with the appliance.
CONSUMER:
Retain this manual for future reference.
This appliance may be installed in an after-market permanently located,
manufactured (mobile) home, where not prohibited by local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This
appliance is not convertible for use with other gases, unless a certied kit is used.
Only doors certied with the appliance shall be used
Massachusetts installations (Warning): This product must be installed by a licensed plumber or
gas tter when installed within the Commonwealth of Massachusetts. Other Massachusetts code
requirements: Flexible connector must not be longer than 36in., a shut off valve must be installed;
only direct vent sealed combustion products are approved for bedrooms/bathrooms. A carbon
monoxide detector is required in all rooms containing gas red direct vent appliances. The replace
damper must be removed or welded in the open position prior to installation of a replace insert.
2
Safety Precautions
HOT GLASS WILL
CAUSE BURNS
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
individuals.
FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” HEATER,
PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:
• All ENVIRO gas-red appliances must be installed in
accordance with their instructions. Carefully read all the
instructions in this manual rst. Consult the building
authority having jurisdiction to determine the need for a
permit prior to commencing the installation.
• NOTE: Failure to follow these instructions could cause
a malfunction of the replace, which could result in death,
serious bodily injury, and/or property damage.
• Failure to follow these instructions may also void your
re insurance and/or warranty.
GENERAL
• Installation and repair should be done by a qualied
service person. The appliance should be inspected before
the rst use and, at least, annually by a qualied service
person. More frequent cleaning may be required due to
excessive lint from carpeting, bedding material, etc. It
is imperative the control compartments, burners and
circulating air passageways of the appliance be kept
clean.
• Due to high temperatures, the appliance should be
located out of high trafc areas and away from furniture
and draperies.
Children and adults should be alerted to the
hazards of high surface temperatures and should
stay away to avoid burn or clothing ignition.
• Young children should be carefully supervised when in
the same room as the appliance. Toddlers, young children
and others may be susceptible to accidental contact
burns. A physical barrier is required if there is a risk for
individuals in the house. To restrict access to a replace
or stove install an adjustable safety gate to keep toddlers,
young children and other at risk individuals out of the
room and away from hot surfaces. Any safety screen,
guard, or barrier removed for servicing an appliance must
be replaced prior to operating the appliance.
• Clothing or other ammable materials should not be
placed on or near the appliance.
• A barrier designed to reduce the risk of burns from the
hot viewing glass is provided with this appliance and shall
be installed for the protection of children and other at-risk
individuals. If the barrier becomes damaged, the barrier
shall be replaced with the manufacturer’s barrier for this
appliance.
FOR YOUR SAFETY
• Installation and service must be performed by a qualied
installer, service agency or gas supplier.
• This installation must conform to local codes or, in the
absence of local codes, with the National Fuel Gas Code,
ANSI Z223.1/NFPA 54, or the Natural Gas and Propane
Installation Code, CSA B149.1.
• To prevent injury, do not allow anyone who is unfamiliar
with the stove to operate it.
• To prevent injury, if the pilot or pilot and burners
have gone out on their own, open the glass door and
wait 5 minutes to air out before attempting to relight the stove.
• Always keep the area around these appliances clear of
combustible material, gasoline and other ammable liquids
and vapours.
• These appliances should not be used as a drying rack for
clothing or for hanging Christmas stockings/decorations.
• Due to the paint curing on the stove, a faint odor and slight
smoking will likely be noticed when the stove is rst used.
Open a window until the smoking stops.
Always connect this gas stove to a vent system and vent to
the outside of the building envelope. Never vent to another
room or inside the building. Make sure the specied vent
pipe is used, properly sized and of adequate height to
provide sufcient draft. Inspect the venting system annually
for blockage and signs of deterioration.
WARNING: Failure to position the parts in accordance
with the diagrams in this booklet, or failure to use only
parts specically approved with this appliance, may result in
property damage or personal injury.
WARNING: Do not operate with the glass front removed,
cracked or broken. Replacement of the glass should be done
by a licensed or qualied service person.
• Never use solid fuels such as wood, paper, cardboard, coal,
or any ammable liquids, etc., in this appliance.
• Do not use this appliance if any part has been under water.
Immediately call a qualied service technician to inspect the
appliance and to replace any part of the control system or
any gas control which has been under water.
• Do not abuse the glass by striking it or slamming the door
shut.
• If the C44I unit is pulled out of its installation, and the vent-
air intake system is disconnected for any reason, ensure that
the vent-air intake pipes are reconnected and re-sealed in
accordance to the instructions noted in
- DIrect Vent
InItIal InstallatIon
3
Table of Contents
Safety Precautions .................................................................................................2
Table of Contents ...................................................................................................4
Codes And Approvals ..............................................................................................5
Specications .........................................................................................................6
Dimensions: ....................................................................................................................6
Rating Label & Lighting Instructions Location:
Operating Instructions ...........................................................................................7
Lighting Instructions: .......................................................................................................7
Air Shutter (Venturi):
Normal Sounds During Operation:
Remote Control Operations:
System Description:
Technical Data:
Transmitter:
Integrated Fireplace Controller (IFC):
Operating Procedure:
Switching to Continuous Pilot Mode:
....................................................................................................................9
.......................................................................................................8
....................................................................................8
.............................................................................................8
.........................................................................................................9
...............................................................................................................9
..............................................................................10
....................................................................................................11
...............................................................................11
Maintenance And Service .....................................................................................14
Routine Maintenance: ....................................................................................................14
Cleaning The Glass:
Cleaning The Firebox:
Replacing the Glass:
Cleaning Decorative Surfaces:
Safety Screen:
Glass Door Removal:
Burner Removal:
Access panels:
Fuel Conversion:
Fuel Conversion:
.......................................................................................................14
....................................................................................................14
......................................................................................................14
........................................................................................15
..............................................................................................................15
....................................................................................................16
...........................................................................................................16
..............................................................................................................17
...........................................................................................................17
...........................................................................................................18
Initial Installation ................................................................................................20
Introduction: .................................................................................................................20
Unit Install Preperation:
Placement and Framing:
Alternate Gas Inlet Location........................................................................................... 22
Vent Termination Framing:
Floor Protection:
Mantel Requirements:
Installation with Recess
Corner Installation:
Horizontal Vent install:
Vertical Vent install:
Clearances & Non-Combustible :
TV Installation Considerations:
Vent Termination Restrictions:
Direct Vent:
Venting Clearances:
Approved Venting Parts:
Allowable Co-Axial Vent Congurations:
Exhuast Restrictor Setting:
Horizontal Termination:
Vertical Termination:
Gas Line Connection and Testing:
Electrical Requirements:
............................................................................................................23
..................................................................................................................30
.................................................................................................20
................................................................................................21
.............................................................................................22
....................................................................................................23
.................................................................................................25
........................................................................................................26
...................................................................................................27
.......................................................................................................27
.....................................................................................28
.......................................................................................29
........................................................................................30
.......................................................................................................31
.................................................................................................32
...........................................................................33
.............................................................................................34
..................................................................................................35
......................................................................................................36
...................................................................................39
.................................................................................................40
Secondary Installation .........................................................................................43
Burner Tray Installation: ................................................................................................43
Panel Installation:
Burner and Tray Media Installation:
Log Set Installation:
..........................................................................................................44
................................................................................45
......................................................................................................46
Trouble Shooting ..................................................................................................48
Parts Diagram .......................................................................................................49
Parts List ..............................................................................................................50
...................................................................6
4
Codes And Approvals
DIRECT VENT ONLY: This type is identied by the sufx DV. This appliance draws all of its air for
combustion from outside the dwelling, through a specially designed vent pipe system.
This appliance has been tested and approved for installations from 0 feet to 4500 feet (1372 m) above
sea level.
In the USA: The appliance may be installed at higher altitudes. Please refer to your American Gas
Association guidelines which state: the sea level rated input of Gas Designed Appliances installed at
elevations above 2000 (610 m) feet is to be reduced 4% for each 1000 feet (305 m) above sea level.
Refer also to local authorities or codes which have jurisdiction in your area regarding the de-rate
guidelines.
In Canada: When the appliance is installed at elevations above 4500 feet (1372 m), the certied high
altitude rating shall be reduced at the rate of 4% for each additional 1000 feet (305 m).
• This appliance has been tested by INTERTEK and found to comply with the established VENTED
GAS FIREPLACE HEATER standards in CANADA and the USA as follows:
VENTED GAS FIREPLACE HEATER (C44I ; NATURAL GAS, PROPANE GAS)
TESTED TO: ANSI Z21.88-2014/CSA 2.33-2014 VENTED GAS FIREPLACE HEATERS
CAN/CGA 2.17-M91 (R2009) GAS FIRED APPLIANCES FOR HIGH ALTITUDES
This ENVIRO C44I Fireplace:
• Has been certied for use with either natural gas or propane (see rating label).
• Is not for use with solid fuels.
• Is approved for a bedroom or bed sitting room. (IN CANADA: must be installed with a listed wall
thermostat. IN USA: see current ANSI Z223.1 for installation instructions.)
• Must be installed in accordance with local codes. If none exist, use current installation code CAN/CGA
B149.1 in Canada or ANSI Z223.1/NFPA 54 in the USA.
• Must be properly connected to an approved venting system and not connected
to a chimney ue serving a separate solid-fuel burning appliance.
IMPORTANT NOTICE (Regarding rst re up): When the unit is turned
on for the rst time, it should be turned onto high without the fan on (if
equipped) for the rst 4 hours. This will cure the paint, logs, gasket material
and other products used in the manufacturing process. It is advisable to
open a window or door, as the unit will start to smoke and can irritate
some people. After the unit has gone through the rst burn, turn the unit
off including the pilot, let the unit get cold then remove the glass door
and clean it with a good gas replace glass cleaner, available at your local
ENVIRO dealer.
5
Dimensions:
Specications
Electrical Inlet
Left Side
965mm
38"
1
2
13mm
19
507mm
"
15
"
16
186mm
30
779mm
1
"
9
8
231mm
7
"
1394mm
5
"
7
16
11
"
16
1174mm
54
8
1
"
46
4
3
"
9
4
247mm
11
284mm
3
"
16
13
"
17
16
453mm
12"
1
"
4
305mm
16
413mm
Gas Inlet
Right Side
83mm
1
"
3
4
1
9
8
232mm
"
1245mm
49"
11
"
2
7"
178mm
Gas Inlet
Bottom
(Optional)
16
68mm
9
232mm
1
"
8
Figure 1. Unit Dimensions
Rating LabeL & Lighting instRuctions Location:
Rotate the safety screen upward or remove the screen completely to access the rating label and lighting
instructions. The plates are attached to a length of chain and are never to be tampered with or removed.
All important information for your replace is on this label as well of the model specic serial number
which you will need for warranty information. The plates are located inside the cabinet on the left side
near the front.
1
4
16
103mm
"
6
Operating Instructions
For Your Safety, Read Safety Precautions And
Lighting Instructions Before Operating
WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY
RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE.
Lighting instRuctions:
FOR YOUR SAFETY READ BEFORE OPERATING
WARNING:
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
A. This appliance is equipped with an ignition device
which automatically lights the pilot. Do not try to
light the pilot by hand.
B. BEFORE OPERATING smell all around the
appliance area for gas. Be sure to smell next to the
floor because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any
phone in your building.
Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
If you cannot reach your gas supplier, call the
fire department.
IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION
C. Use only your hand to push in or
turn the gas control knob. Never
use tools. If the knob will not push
in or turn by hand, don’t try to
repair it, call a qualified service
technician. Force or attempted
repair may result in a fire or
explosion.
D. Do not use this appliance if any
part has been under water.
Immediately call a qualified service
technician to inspect the appliance
and to replace any part of the
control system and any gas control
which has been under water.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Read the owner's manual including the section on
"Remote Control" operation.
3. Set the thermostat to the lowest setting.
4. Turn off all electric power to the appliance.
5. Do not attempt to light the pilot by hand.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP!
Follow "B" in the safety information above on this label.
If you don't smell gas, go to the next step.
7. Turn on all electric power to the appliance.
8. Using the remote control, set
thermostat to desired setting, or
press the ON/OFF key on the
remote. "ON" will be indicated on the
display of the remote and an audible
"beep" will be heard at the unit to
indicate the command has been
received.
9. This appliance is equipped with a
completely automatic ignition and
lighting control. The control will
attempt to light the pilot several
times if necessary. If it is
unsuccessful, it will discontinue
operations. If the appliance will
not operate, follow the
instructions "To Turn Off Gas To
Appliance" and call your service
technician or gas supplier.
Blue LCD Display
ON/OFF Key
THERMOSTAT Key
UP/DOWN Arrow Key
MODE Key
1. Set thermostat to lowest setting, or press the ON/OFF Key. "OFF" will be indicated on the display
and an audible "Beep" will be heard at the unit to indicate the command has been received.
2. Turn off all electric power to the appliance if service is to be performed.
TO TURN OFF GAS TO APPLIANCE
C-12455
Figure 2. IPI Lighting Instruction Label
7
Operating Instructions
aiR shutteR (VentuRi):
The air shutter plays a very important role in ame appearence and combustion quality. The shutter adjusts
how much air gets mixed with the gas before it ignites. Adjustments can be made to accomodate various
climates and vent congurations.
To gain access to the air shutter remove the safety screen and intake shield. There is a lever underneath the
rebox near the gas valve as shown in Figure 3. Moving the lever to the right will close off the air mixing
with the gas and will make the ame appear more yellow and tall. Moving the lever to the left will open up
the shutter allowing more air to be mixed with the incoming gas; this will make the ames appear more blue
and short.
Typically natural gas ames will
require the shutter to be more closed.
Typically LP ames will require the
shutter to be more open.
If you cannot attain the proper ame by
making air shutter adjustments then you
may have the incorrect exhaust restrictor.
If the ame is very ickery, fast moving, and
low then increase the restriction.
If the ame is very tall, lazy, and dirty then
decrease the restriction.
More details can be found in the venting
section of this manual.
Figure 3. Air shutter adjustment lever
Caution: Wear heat resistent gloves
when making adjustments to the air
shutter. Perform adjustments after 15
minutes.
noRmaL sounDs DuRing opeRation:
Table 1: Normal Sounds
Component Sound & Reason
Main Unit Creaking when heating up or cooling down.
Burner Light pop or poof when turned off; this is more common with LP units.
Temperature Sensor Clinking when it senses to turn the blower on or off.
Pilot Flame Quiet whisper while the pilot ame in on.
Blower / Fan Air movement that increase and decreases with the speed of the blower. The
blower is pushing the heat from the replace into the room.
Gas Control Valve Dull click when turning on or off, this is the valve opening and closing.
Remote contRoL opeRations:
Proame 2 is a modular remote control system that directs the functions of the C44I. The Proame 2
TMFSLA is congured to control the on/off main burner operation, its ame levels and provides on/off
and thermostatic control of the appliance. The system also controls the optional fan speed through six
(6) levels and can control the operation of the option light kit.
8
Operating Instructions
Blue LCD display
UP/DOWN Arrow Key
ON/OFF Key
THERMOSTAT Key
MODE Key
system DescRiption:
The Proame 2 Remote Control System consists of two (2) elements:
1. Proame 2 Transmitter.
2. Integrated Fireplace Controller (IFC) and a wiring harness to connect to the gas valve and stepper
motor.
ATTENTION!
- TURN “OFF” THE MAIN GAS SUPPLY OF THE APPLIANCE DURING INSTALLATION OR
MAINTENANCE OF THE IFC.
- TURN “OFF” MAIN GAS SUPPLY TO THE APPLIANCE PRIOR TO REMOVING OR REINSERTING
THE BATTERIES IN THE BATTERY HOLDER
technicaL Data:
Transmitter (Remote Control):
Supply voltage: 4.5 V (three 1.5 V AAA batteries)
Radio frequency: 315 MHz
Integrated Fireplace Controller (IFC):
Supply voltage: AC IN - 120 V / 60 Hz
Battery Backup IN - 6 Vdc - 200mA (four 1.5 V AA batteries)
Spark voltage / frequency: >10kV / 1Hz
Comfort modulating fan: 120 V / 60 Hz / 2A
Auxiliary: 120 V / 60 Hz / 5A (not used)
tRansmitteR:
The Proame 2 Transmitter is a black remote control with a blue backlit lcd display. It uses a streamline design
with a simple button layout and informative lcd readout (Figure 5). The Transmitter is powered by three (3)
AAA type batteries. A Mode Key is provided to Index between the features and a Thermostat Key is used to
turn on/off or index through Thermostat functions (Figure 4 & 5)
Figure 4: Proame 2 Transmitter.
9
Low battery alarm
Key Lock
Room
Temperature
Dimmer ON
Set Point
Temperature/Level/State
Flame ON
Thermostat OFF/
ON/SMART
Comfort fan
Transmission
Split Flow
Aux ON
CPI mode
Operating Instructions
Figure 5: Proame 2 Transmitter LCD Screen.
integRateD FiRepLace contRoLLeR (iFc):
The Proame 2 IFC (Figure 6) connects directly to the gas valve, split ow valve, stepper motor, pilot and covection fan
with a wiring harness. The IFC is mainly powered by 120 VAC but can also run off a battery backup four (4) AA type
batteries for shorter periods of time. The IFC accepts commands via radio frequency from the Transmitter to operate
the appliance in accordance with the particular Proame 2 system conguration. The IFC has a red reset button at the
front right corner that is used is to synchronize the Transmitter when using the for the rst time, or after the batteries
have been replaced.
10
Reset Button
Figure 6: Integrated Fireplace Controller
Operating Instructions
opeRating pRoceDuRe:
Initializing The System For The First Time
Install the four (4) AA batteries into the IFC battery holder. Note the polarity of the battery and insert into the battery
bay as indicated on the body of the battery holder. Press the reset button on the IFC marked “SW1” (see Figure 6).
The IFC will “beep” three (3) times to indicate that it is ready to synchronize with a Transmitter. Install the three (3)
AAA type batteries in the Transmitter battery bay, located on the base of the Transmitter. With the batteries already
installed in the Transmitter, push the ‘ON’ button. The IFC will “beep” four (4) times to indicate the Transmitter’s
command is accepted and sets to the particular code of that Transmitter. The system is now initialized.
Temperature Indication Display
With the system turned OFF, press the Thermostat Key
and the Mode Key at the same time. Look at the LCD
screen on the transmitter to verify that a °C or °F is
visible to the right of the Room Temperature display
(see Figure 7).
Turn on the Appliance
Press the ON/OFF Key on the Transmitter. The
Transmitter display will show all active Icons on the
screen. A single “beep” from the IFC will conrm
reception of the command and will commence to rst
ignite the pilot light, followed by the main burner. This should take about 10 seconds to complete.
Figure 7: Remote Control Display in Farenheit and Celcius.
switching to continuous piLot moDe:
When the C44I is turned off press the mode key to index to the constant pilot (CPI) mode icon (see gure 8).
Pressing the up arrow key will select Continuous Pilot Ignition (CPI) and pressing the down arrow key will return
to IPI. Once a selection is made the IFC will beep once to conrm it had received the command. NOTE: It is
recommended to use the continuous pilot mode during the winter when the outside temperature
is below 50°F (10°C) to keep the chimney properly heated for updraft during burner ignition.
Continuous pilot mode also keeps the rebox warm which eliminates both heat loss to cold air that is trapped
inside the rebox as well as excessive exhaust vapour condensation on the door glass.
Figure 8: CPI Pilot Mode.
11
Room Temperature
Set Temperature
Thermostat ON
Flame Off
Flame Level 1
Flame Level 5
Maximum Flame Level
Operating Instructions
Turn off the Appliance
Press the ON/OFF Key on the Transmitter. The Transmitter LCD display
will only show the room temperature and Icon (see Figure 9). A single
“beep” from the IFC conrms reception of the command and both the
pilot light (if the unit is not set to continuous pilot) and main burner will
turn off.
Room Thermostat (Transmitter Operation)
The Remote Control can operate as a room thermostat. The thermostat
can be set to a desired temperature to control the comfort level in a
room. To activate this function, press the Thermostat Key (see Figure
4). The LCD display on the Transmitter will change to show that the
room thermostat is “ON” and the set temperature is now displayed (see
Figure 9). To adjust the set temperature, press the Up or Down Arrow
Keys until the desired set temperature is displayed on the LCD screen of
the Transmitter.
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the ame height
in accordance to the difference between the set point
temperature and the actual room temperatures. As the room
temperature gets closer to the set point the Smart Function
will modulate the ame down. To activate this function,
press the Thermostat Key (Figure 4) until the word “SMART”
appears to the right of the temperature bulb graphic (Figure
10). To adjust the set temperature, press the Up or Down
Arrow Keys until the desired set temperature is displayed on
the LCD screen of the Transmitter.
Figure 10: Remote Control’s Smart Flame Function.
Figure 9: Remote Control Displays
Set Temperature.
Remote Flame Control
The Proame 2 remote control system has six (6) ame levels.
With the system on, and the ame level at the maximum
in the appliance, pressing the Down Arrow Key once will
reduce the ame height by one step until the ame is turned
off. The Up Arrow Key will increase the ame height each
time it is pressed. If the Up Arrow Key is pressed while the
system is on but the ame is off, the ame will come on in
the high position. A single “beep” will conrm reception of the
command.
Fan Control
The C44I has a dual convection fan kit that can be controlled
with the Transmitter. The fan speed can be adjusted thorugh
six (6) speeds. To control the fan press the Mode key to
index to the fan control icon. Use the UP/DOWN arrow keys
to turn on, off, or adjust the fan speed. A single beep from
the IFC will conrm the command has been received
Figure 11: Remote Control’s Flame Levels.
12
Figure 12: Fan Control
Operating Instructions
Auxiliary Control
This function is not used on the C44I and can be disregarded.
Figure 13: Auxiliary Control (not used)
Dimmer Control
This is only appliciable if the light kit has been installed. Press the
mode key until the light bulb symbol is visable (Figure 14). This
turn the lights on and off as well as adjust 6 dimming levels.
Key lock
This function will lock the keys to avoid unsupervised operation. To activate this
function, press the Mode and UP keys at the same time and the a lock will appear
(see Figure 15). To de-activate this function, press the Mode and UP Keys at the
same time.
Figure 14: Dimmer Control
Low Battery Power Detection
Transmitter: The life span of the remote control batteris depends on various
factors: quality of the batteries used, the number of ignitions of the appliance, the
number of changes to the room thermostat set point etc. When the Transmitter
batteries are low, a Bettery Icon will appear on the LCD display of the Transmitter
(see Figure 16) before all battery power is lost. When the batteries are replaced
this icon will disappear.
IFC: The life span of the IFC batteries depends on various factors during a
prolonged power outage: quality of the batteries used, the number of ignitions
of the appliance, the number of changes to the room thermostat set point etc.
When the IFC batteries are low, No “beep” will be emitted when it receives an On/
Off command from the Transmitter. This is an alert for a low battery condition for
the IFC. When the batteries are replaced the “beep” will be emitted from the IFC
when the ON/OFF Key is pressed (See
WARNING: Fire Hazard. Can cause severe injury or death. The
Transmitter causes ignition of the appliance. The appliance can turn
on suddenly. Keep away from the appliance burner when operating the
remote system.
WARNING: Shock Hazard. Can cause severe injury or death. This device is powered by line voltage. Do
not try to repair this device. In no way is the enclosure to be tampered with or opened. Disconnect from
line voltage before performing any maintenance.
InItIalIzIng the system for the fIrst tIme).
Figure 15: Key Lock
Figure 16: Low Battery
CAUTION: Property Damage Hazard. Excessive heat can cause property damage. The appliance can stay
lit for many hours. Turn off the appliance if it is not going to be attended for any length of time. Always
place the Transmitter where children cannot reach it.
13
Maintenance And Service
Routine maintenance:
At least once a year, run through the following procedures to ensure the system is clean and working
properly. Check the burner to see if all the ports are clear and clean. Check the pilot to make sure it is not
blocked by anything. The pilot ame should be blue with little or no yellow on the tips.
Warning: Clearances must be sufcient to allow access for maintenance and service.
Warning: Failure to position the parts in accordance with this manual, or failure to use only parts
specically approved with this appliance may result in property damage or personal injury.
The venting system must be periodically examined; it is recommended the examination is done by a
qualied agency.
cLeaning the gLass:
When the replace has cooled, remove the safety screen and glass door. See maIntenance anD
serVIce - glass Door remoVal. Check the gasket material on the back of the glass, making sure that it is
attached and intact.
During a cold start up, condensation will sometimes form on the glass. This is a normal condition with all
replaces. However, this condensation can allow dust and lint to cling to the glass surface. Initial paint
curing of the appliance can leave a slight lm behind the glass, a temporary problem. The glass will need
cleaning about two weeks after installation. Use a mild glass cleaner and a soft cloth. Abrasive
cleaners will damage the glass and painted surfaces. Depending on the amount of use, the glass
should require cleaning no more than two or three times a season. Do not clean the glass when it is
hot.
cLeaning the FiRebox:
Remove the logs carefully, as they are very fragile. Gently remove all the media and place on a paper
towel. Vacuum the bottom of the rebox thoroughly. Carefully clean any dust off the logs and remove
any lint from the burner and pilot. At this time, inspect the burner tube for cracking or severe warping.
If a problem is suspected, contact the dealer. Check the logs for deterioration or large amounts of soot;
a small amount on the bottom side of the logs is normal. Replace the logs as shown in the seconDary
InstallatIon - log set InstallatIon section. If new/more media is required, contact your nearest ENVIRO
dealer.
RepLacing the gLass:
The glass in the replace is a high temperature ceramic. If the glass is damaged in any way, a factory
replacement is required (see Parts lIst). Wear gloves when handling damaged glass door assembly to
prevent personal injury. Do not operate with the glass front removed, cracked or broken. Removal and
replacement of the glass from the door must be done by a licensed or qualied service person. The
glass must be purchased from an ENVIRO dealer. No substitute materials are allowed. To
remove the door (see page 16). The replacement glass will come with a new gasket installed. Remove
any silicone remnants from the door. Apply high temperature silicone to the two vertical faces of the
door and install the new piece of glass with gasket (be sure to maintain edge clearances). Apply even
pressure to the glass to allow the silicone to adhere to the gasket material.
14
Maintenance And Service
cLeaning DecoRatiVe suRFaces:
Painted and porcelain faces should be wiped with a damp cloth periodically. If a plated face has been
purchased, it should be unpacked/unwrapped carefully to avoid getting anything on the surface of the
nish, including cleaners, polish and nger prints. It is important to note that ngerprints and other
marks can leave a permanent stain on plated nishes. To avoid this, give the face a quick wipe with
denatured alcohol on a soft cloth BEFORE lighting the replace. Never clean the face when it is
hot. Do not use other cleaners as they may leave a residue, which can become permanently etched into
the surface.
saFety scReen:
A safety screen is installed from the manufacture to protect its users from the dangers of the hot glass
preceding it. There are four safety screen mounting brackets that hold the screen into position as shown
in Figure 17. In order to remove the safety screen it is easiest to grab with both hands from the bottom
and lift the screen up off the mounting brackets and outward.
Figure 17. Safety Screen Removal
15
Maintenance And Service
gLass DooR RemoVaL:
To remove the glass door use a
3/8 socket to remove the 4 upper
bolts and rotate outward. To
replace the door simply reverse
the order; do not over tighten
the bolts or they may strip.
WARNING: Do not touch or
attempt to remove the glass door
if the replace is not completely
cold.
WARNING: Never operate the
replace with the glass door
removed.
buRneR RemoVaL:
The burner will need to be removed to maintenance and fuel conversion. Follow the procedure carefully.
Proceed only when the unit has completely cooled down.
1. Remove the safety screen as shown in maIntenance anD serVIce - safety screen remoVal.
2. Remove the glass door as shown in the maIntenance anD serVIce - glass Door remoVal.
3. Remove log set or high denition rock set (if installed).
4. Remove any media from the media tray.
5. Remove the media tray as shown in seconDary InstallatIon - meDIa tray remoVal.
6. Remove the six T-20 screws securing the burner pan as shown in Figure 19; do NOT remove the other
T-20 screws. Once the specied screws are removed slide burner to the left and lift out to remove.
To re-install the burner follow steps above in reverse. When placing the burner back in the unit be sure not
to move the air shutter. Make sure the burner is slid all the way in or the mounting holes will not
line up. Do not over tighten the burner screws or they might strip; just get them snug.
Figure 18. Door Removal Motion
16
Figure 19. Removing Burner
Maintenance And Service
access paneLs:
There are two access doors in the bottom on the rebox that is used for servicing components after the unit
is installed in a construction enclosure. Proceed only when the unit has completely cooled down.
1. Remove the burner and burner tray
as shown in the maIntenance anD
serVIce - Burner remoVal.
2. Remove the (14) T-20 bolts retaining
the access panels as shown in Figure
10.
3. After servicing assemble in the
Figure 20. Removing Access Door
intake shieLD RemoVaL:
You will need to remove the Intake Shield
to gain access to the components below
and make adjustments to the air shutter.
To remove the shield simply lift it up off the
slots.
reverse order and be sure the gasket
is still intact. Replace if necessary.
DO NOT run the unit without the Intake
Shield as it allows the unit to evacuate heat
out of the unit and protect the components.
Figure 21. Removing Intake Shield
FueL conVeRsion:
TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY
Please read and understand these instructions before installing.
Warning: This conversion kit shall be installed by a qualied service agency in accordance
with the manufacturer’s instructions and all applicable codes and requirements of the
authority having jurisdiction. If the information in these instructions is not followed
exactly, a re, explosion or production of carbon monoxide may result causing property
damage, personal injury or loss of life. The qualied service agency is responsible for
the proper installation of this kit. The installation is not proper or complete until the
operation of the converted appliance is checked as specied in the manufacturer’s
instructions supplied with the kit.
17
Loading...