Enviro Boston 1200-C Free Standing, Boston 1200-C, Boston 1700C, Boston 1200FS, Boston 1700FS Owner's Manual

Download

Page 1

Boston

Model: 1200-C Free Standing

OWNERS MANUAL

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED

PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE

INSTALLER:

Leave this manual with the wood stove.

CONSUMER:

Retain this manual for future reference.

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS WOOD

BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT

IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.

Tested & Listed By

OMNI-Test Laboratories, Inc,

T L

O-

Report # 268-S-04b-2

Portland

Oregon USA

This heater meets the U. S. Environmental Protection Agencies emission limits for wood heaters sold after July 1st, 1990. Under specic conditions this heater has been shown to deliver heat at rates ranging from 11,479 to 34,196 BTU per

hour for the 1200 and from 9,425 to 31,780 BTU per hour for the 1700.

PAPER.

Contact your local building or re ofcials,

or the authority having jurisdiction about

restrictions and installation inspection

requirements in your area.

50-2439

Page 2

Table of Contents

Safety Precautions.............................................................................................3

Operating Instructions........................................................................................4

Building Your Fire...................................................................................6

Air Control.............................................................................................9

How It Works.......................................................................................10

Specications..................................................................................................11

1200 Specications...............................................................................11

Clearances To Combustibles - 1200 Freestanding.....................................12

Dimensions - 1200 Freestanding............................................................13

Installation......................................................................................................14

Removal From Pallet.............................................................................14

Hearth Protection Examples...................................................................15

Outside Air Kit......................................................................................18

Recommended Heights And Diameters For Flue Pipe...............................18

Chimney Installation Through Wall.........................................................19

Installation of A Listed, Factory Built Chimney - Freestanding...................20

Masonry Fireplace Installation - Freestanding..........................................22

Mobile Home Installation.......................................................................23

Model 1200 Brick Placement & Tube Locations........................................25

C-Cast Ceramic Bafe Installation..........................................................26

Fan Wiring Diagrams.............................................................................26

Optional Fan Installation - Freestanding..................................................27

Disassembly.......................................................................................28

Removal of Cast Sides and Cast Door........................................................28

Door Latch Adjustment..........................................................................28

Rating Label.....................................................................................................29

Parts List.........................................................................................................30

Parts Diagram - Freestanding............................................................................31

Warranty.........................................................................................................32

Installation Data Sheet.....................................................................................36

Page 3

Safety Precautions

FOR SAFE INSTALLATION AND OPERATION OF YOUR “ENVIRO” WOOD STOVE, PLEASE CAREFULLY READ THE FOLLOWING INFORMATION:

● Please read this entire manual before you install and use your new woodstove. Failure to follow instructions may result in property damage, bodily injury or even death. Be aware that local Codes and Regulations may override some items in this manual. Check with your local inspector.

● If this appliance is not properly installed, operated and maintained, a serious house re could result. Makeshift materials during installation could also result in a serious house re.

● HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING, AND FURNITURE AWAY. CONTACT MAY CAUSE SKIN BURNS.

● Operate only with the door and ash plug tightly closed and burn wood directly on the stove hearth. Do not operate if the door glass is broken or a gasket is missing or damaged. Do not alter the combustion air control valves. Dangerous overring could occur which could ignite creosote in the chimney or cause a house re.

● At least 12 square inches (77.4 cm to the stove through a 4 inch (10.16 cm) diameter pipe. For the stove to operate combustion-air must be supplied through either the bottom or the back of the unit.

● Do not burn coal or charcoal as there is danger of carbon monoxide being produced. DO NOT USE CHEMICAL FLUIDS TO START OR RE-FRESH THE FIRE. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH AS GASOLINE, GREASE, NAPHTHA OR ENGINE OIL. Never let the stove become hot enough to get any part red or glowing red.

) of fresh outside air should be admitted into the room or directly

● Burning wet, unseasoned wood could cause excessive creosote accumulation in the ue pipe. When ignited, it could cause a chimney re that could result in a serious house re.

● Do not use grates, andirons or any other methods to support or raise the re up off the hearth of the appliance.

● This appliance is tested to ULC-S627-00 Standard for Space Heaters for Use with Solid Fuel & UL 1482

-10 Standard for Safety for Solid-Fuel Type Room Heaters.

● In Canada the existing chimney must be lined to the termination for all masonry installs.

● A chimney connector shall not pass through an attic or roof space, closet or similar concealed space,

or a oor, or ceiling.

● Where passage through a wall, or partition of combustible construction is desired, the installation shall

conform to CAN/CSA-B365.

● DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

● In the event of component failure, only manufacturer specied replacement parts may be used.

● DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

● Ensure that the ash plug is installed over the ash dump hole.

● Do not open the ash pan compartment while the unit is burning. Allow unit to fully cool before touching

the ash pan latch.

Page 4

Operating Instructions

FIRST START

When rst installed, the chimney, rebricks and steel are cold and it usually takes several hours on a fairly high burn for them to become hot and dry enough for the stove to function well. We recommend during the unit’s rst burn that a door and window are opened to vent the smoke and fumes created from the unit’s paint curing. The paint will smell a little for the rst burn or two as it cures.

DISPOSAL OF ASHES:

The Boston freestanding models are equipped with an ash plug in the rebox and an ash drawer. Lift the ash plug out and push the ashes that have accumulated into the hole; the ashes will then drop into the Ash Pan. Ensure that the ash plug is seated properly before relighting the unit. When the Ash Pan is ready to be emptied, fully open the main door on the unit and then open the lower latch on the Cast Ash Drawer. The Cast Ash Drawer will lower down and the Ash Pan will be accessible (see Figure 1). Ashes should be placed in a steel container with a tight tting lid. The closed container of ashes should be placed on a noncombustible oor or on the ground, well away from all combustible materials, pending nal disposal. If the ashes are disposed of by burial in soil or otherwise locally disposed, they should be retained in the closed container until all cinders have thoroughly cooled. Other waste shall not be placed in this container. Prior to burning the unit, re-insert the Ash Pan into the unit and close the Cast Ash Drawer, ensuring that the latch is closed securely.

FAN OPERATION:

This unit has been approved for operation with or without the optional fan supplied by the manufacturer. On medium or high burns, using a fan will increase the heat transfer slightly. Route the power supply cord along the oor behind the stove where it will remain cool.

1. Plug the fan assembly into a standard three prong grounded electrical receptacle.

2. Turn the rotary fan controller to the desired setting. Once operating temperature is reached, the fan temperature sensor will turn the fan on. When the unit cools down, the fan temperature sensor will shut the fan off automatically.

Figure 1: Ash Pan Removal

Page 5

Operating Instructions

REPLACING THE GLASS:

Never strike or slam the door, hit the glass or let burning wood rest against it. If the glass cracks when the re is burning, do not open the door until the re is out and do not operate the stove again until the glass has been replaced. If the glass is damaged in any way, a factory replacement is required (see “

Parts List”). To replace the glass, remove the steel retaining clips and all loose glass. Replace only with

Neoceram 5 mm glass 16.61” (422 mm) x 10.63” (270 mm) and wrap the edges with 0.125” (3.2 mm) x

0.5” (13 mm) self-adhesive berglass gasket.

Wear gloves when handling damaged glass door assembly to prevent personal injury. When the glass door assembly is being transported, it must be wrapped in newsprint and tape and/or a strong plastic bag.

The glass must be purchased from an ENVIRO dealer. No substitute materials are allowed.

FIRE EXTINGUISHER AND SMOKE DETECTION:

All homes with a solid fuel burning stove should have at least one re extinguisher in a central location known to all in the household and a smoke detection device in the room containing the stove. If it sounds the alarm, correct the cause but do not deactivate. You may choose to relocate the smoke detection device within the room; DO NOT REMOVE THE SMOKE DETECTOR FROM THE ROOM.

CREOSOTE - FORMATION AND NEED FOR REMOVAL:

When wood is burned slowly, it produces tar and other organic vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively cool chimney of a slow-burning re. As a result, creosote residue accumulates on the ue lining. When ignited this creosote makes an extremely hot re. The chimney connector and chimney should be inspected bi-weekly during the heating season to determine if a creosote buildup has occurred. If creosote has accumulated (3mm or more) it should be removed to reduce the risk of a chimney re.

MAINTENANCE:

At the end of each heating season clean the chimney and the smoke pipe. If soot has accumulated above the top bafe bricks, remove, clean, and then replace them. If a secondary air tube is badly corroded, replace it. Replace worn door gaskets and broken bricks as needed.

FAILURE TO INSPECT AND CLEAN YOUR CHIMNEY SYSTEM REGULARLY CAN RESULT IN A CHIMNEY FIRE, WHICH COULD DAMAGE THE CHIMNEY OR CAUSE A HOUSE FIRE.

CHIMNEY OR RUN AWAY FIRE:

1. Call local re department (or dial 911)

2. Close the draft fully

3. Examine the ue pipes, chimney, attic, and roof of the house, to see if any part has become hot

enough to catch re. If necessary, spray with re extinguisher or water from the garden hose.

4. Do not operate the stove again until you are certain the chimney and its lining have not been damaged.

Page 6

Operating Instructions

Building Your Fire:

Proper operation of your stove will help to ensure safe, efcient heating. Please take a few moments to review these simple operating procedures.

IMPORTANT: Please be aware when loading your stove that the air tubes in the rear are lower.

1. Fuel Selection:

This stove is designed to burn natural wood only. Higher efciencies and lower emissions generally result when burning air-dried seasoned hardwoods, as compared to softwoods or too green or freshly cut hardwoods. DO NOT BURN the following: treated wood, coal, garbage, solvents, colored papers or trash. Burning these may result in the release of toxic fumes and may poison or render the secondary air tubes ineffective. Burning coal, cardboard or loose paper can produce soot, or large akes of char or y ash that can coat the combustor, causing smoke spillage into the room, and rendering the combustor ineffective.

2. Building/Maintaining a Fire:

a) Open the primary air slide by pulling it all the way to the right.

b) Place a base of crumpled uncolored newspaper in the bottom of the stove. Lay pieces of kindling on

top of the newspaper and light it.

CAUTION: “Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid,

or similar liquids to start or “freshen up” a re in this heater. Keep all such liquids well away from heater while it is in use.

c) As the kindling begins to burn, add several larger pieces of wood until the re is burning well. At this

point, regular size logs may be added.

NOTE: Until the re is burning well, leave the air controls fully open.

d) Regulate the heat output of the stove by adjusting the air controls to allow a larger re and vice versa.

A short period of experimentation with the control settings will allow you to regulate the heat output to keep your home comfortable.

Do not use a grate or elevate the re. Build wood re on the stove rebox hearth oor.

3. Refueling the Stove:

Use a long pair of gloves (barbecue gloves) when feeding the re because these stoves burn at the front. They are clean and efcient but they are also very hot and gloves are useful. Keep a small steel shovel and whisk nearby for moving a log or lifting a fallen ember and for keeping the hearth clean.

a) Before attempting to add fuel to the stove, OPEN the damper control fully by pulling it all the way out. This allows the chimney to carry away the additional smoke, which occurs when the door is open.

b) DO NOT OVERLOAD THE STOVE. Normally, three or four logs will provide heat for several hours. Never operate this stove where portions glow red hot.

c) DO NOT OVERFIRE. If the heater or chimney connector glows, you are overring. Overring could ignite creosote in the chimney and cause a house re.

d) CAUTION: DO NOT PLACE FUEL OR COMBUSTIBLE MATERIAL WITHIN SPACE HEATER INSTALLATION CLEARANCES OR WITHIN THE SPACE REQUIRED FOR CHARGING AND ASH REMOVAL. LOGS SHOULD BE KEPT IN A BIN OR CONTAINER TO REDUCE THE RISK OF LOGS ROLLING INTO THE UNIT’S CLEARANCES. e) KEEP THE ASH LIP CLEAR OF EMBERS AND ASH. If the door is closed with debris in the way, the door gasket seal could be compromised.

Page 7

Operating Instructions

4. For Maximum Efciency:

When the stove is hot, load it fully to the top of the door opening and burn at medium low settings. When the fuel is mostly consumed, leaving a bed of red coals, repeat the process. Maximum heat for minimum fuel occurs when the stove top temperature is between 250°F (120°C) and 550°F (290°C). The most likely causes of dirty glass are: not enough fuel to get the stove thoroughly hot, burning green or wet wood, closing the draft until there is insufcient air for complete combustion, or a weak chimney draw. Indeed, the cleanness of the glass is a good indicator of the stove operating efciently.

Helpful Hints Worth Repeating

1. Helpful advice on the correct way to start your re.

a) You will need small pieces of dry wood, called kindling, and paper. Use only newspaper or paper

that has not been coated or had other materials glued or applied to it. Never use coated (typically

advertising yers) or coloured paper. b) Always open the door of the wood stove slowly to prevent suction and drawing smoke into the room. c) Crumple several pieces of paper and place them in the center of the rebox and directly onto the

rebricks of the wood stove. Never use a grate to elevate the re. d) Place small pieces of dry wood (kindling) over the paper in a “teepee” manner. This allows for good

air circulation, which is critical for good combustion. e) Light the crumpled paper in 2 or 3 locations. Note: It is important to heat the air in the stovepipe for

draft to start. f) Fully open the air controls of the wood stove and close the door until it is slightly open, allowing for

much needed air to be introduced into the rebox. Never leave the door fully open, as sparks from

the kindling may y out of the stove, causing damage or injury. As the re begins to burn the kindling,

some additional kindling may be needed to sustain the re. DO NOT add more paper after the re has

started. g) Once the kindling has started to burn, add some smaller pieces of seasoned, dry rewood. Note:

Adding large pieces at the early stages will only serve to smother the re. Continue adding small pieces

of seasoned dry rewood, keeping the door slightly open until each piece starts to ignite. Remember

to always open the door slowly between placing wood into the re. h) Once the wood has started to ignite and the smoke has reduced, close the wood stove door fully. The

reduction of smoke is a good indication that the draft in the chimney has started and good combustion

is now possible. Larger pieces of seasoned, dry rewood can now be added when there is sufcient

space in the rebox. Adjust the air control setting to desired setting. Note: The lower the air control

setting, the longer the burn time of your rewood.

2. What type of wood is best to use as rewood?

Both hardwood and softwood burn well in this stove. Both woods contain about 8,000 BTU/lb (18,570 KJ/Kg), but hardwood is generally more dense, will weigh more per cord, and burns a little slower and longer. Cutting rewood so that it will t horizontally, front to back, makes it easier loading and less likely for the fuel to roll on the glass. Except for a cold start, there is no need to crisis-cross the logs. Ideal length for the logs used in the 1200-C would be about 16“ (381 mm) but it can burn pieces up to 18” long. Ideal length for the logs used in the 1700-C would be about 18“ (381 mm) but it can burn pieces up to 20” long logs. Burn only dry, seasoned wood. It produces more heat and less soot or creosote. Freshly cut wood has about 50% moisture. A 10 pound (4.5 Kg) log contains 5 pounds (2.3 Kg) of water. To season rewood, split and stack it so that air can get to all parts of the wood. Burn beach wood only if its salt content has been washed away in a season of rain and then the wood dried. To prevent smoke

Page 8

Operating Instructions

spillage when refueling, open the door slowly.

3. What does dry, seasoned wood mean?

Wood that has been dried for a period of one year in a well-ventilated and sheltered area would be considered dry, seasoned wood. Wood from slow-growing trees is generally considered better than wood from fast-growing trees. To season rewood, split and stack it so that air can get to all parts of the wood.

4. Will following the above-listed steps for starting a re mean perfect results every time?

The quick answer is ‘most of the time’. There are many variables that may affect your success when starting a re. Most of those variables and how to deal with them will be learned through experience. Your ability to start a good re will signicantly increase with time and patience. Some of the reasons for poor stove performance will be covered in the next section of these instructions.

5. Why can’t I get the re lit?

Damp or wet wood and poor drafts are the main reasons for poor results in starting a re. Always use dry, seasoned wood for your re. Even wood dried for two years will be difcult to ignite if it has become wet.

6. Is it normal for soot to cover the glass at the beginning of a re?

Your stove has been built with an air-wash system that will help keep the glass clear when the rebox has reached a good operating temperature and has a good draft. Normally, a hot stove will keep the glass clean, but if you must clean the glass, use a soft cloth with no abrasive and clean only when the unit is cold. Cold rebox temperature and poor draft cause sooting of the glass. Once the rebox temperature and the draft increase, the soot will burn off.

7. What is draft?

Draft is the ability of the chimney to exhaust or draw smoke produced during the normal combustion process. Too much draft may cause excessive temperatures in the appliance and may damage the appliance. Inadequate draft may cause backpufng or “plugging” of the chimney. There is a certain amount of draft that is required to allow for your stove to function at its’ highest efciency. A water column gauge can be used to reference this amount.

8. What can cause a poor draft?

The most common factors for poor draft are: a) Air supply

b) Environmental conditions c) Cold chimney temperature d) Poor chimney installation and maintenance e) Atmospheric pressure

a) Air supply – Inside the home, normal household appliances such as clothes dryers and forced-air

furnaces compete for air, resulting in air starvation to the re. This creates a condition in the house known as negative pressure. When a house experiences negative pressure, the combustion gases can be drawn from the chimney and into the house. This condition is commonly referred to as down-

Page 9

Operating Instructions

drafting. Increased amounts of insulation, vinyl windows, extra caulking in various places and door

seals can all keep heat in but may also make a home too airtight. An easy way to stop negative

pressure in a home is to crack a window in the room containing the stove.

b) Environmental Conditions - High trees, low-lying house location such as in a valley, tall buildings or

structures surrounding your house and windy conditions can cause poor draft or down-drafting.

c) Cold Chimney Temperature - Avoid cold chimney temperatures by burning a hot re for the rst fteen

to forty minutes, being careful not to over-re the stove. If any part of the chimney or parts of the

stove start to glow, you are over-ring the stove. Where possible, install a temperature gauge on the

chimney so temperature drops can be seen.

d) Chimney Installation and Maintenance - Avoid using too many elbows or long horizontal runs. Too short

a chimney can cause difcult start-up, dirty glass, back smoking when door is open, and even reduced

heat output. Too tall a chimney may prompt excessive draft, which can result in very short burn times

and excessive heat output. If in doubt, contact a chimney expert and/or chimney manufacturer for

help. Clean chimney, rain caps and especially the spark arrestor regularly, to prevent creosote build-

up, which will signicantly reduce chimney draw and possibly a chimney re.

Note: These instructions are intended as an aid and do not supercede any local, provincial or state

requirements. Check with ofcials or authorities having jurisdiction in your area.

Air Control:

The air wash and pilot air (control the amount of air to the re) are controlled by the rod located on the right side of the unit. To increase your air, pull the rod out and to decrease, push the rod in. All the units have a secondary air that ows through the tubes at the top of the rebox, just below the bafes.

Pull this control all the way out when rst starting the stove. Once the re has been established you may adjust this control to set the burn rate of the re. If this damper is closed at rst start-up, the re will burn very slowly and could soot the appliance.

When shutting down the stove, fully open the air control. This allows the chimney temperatures to remain as high as possible for as long as possible. Cold chimney temperatures create creosote. Warning - This adjustment should not be altered for increased ring for any reason.

Increase air - pull rod out

Decrease air - push rod in

Figure 2: Air Control Rod.

Page 10

How it works:

Operating Instructions

Figure 3: 1200 Air Flow Path.

Page 11

1200 speCiFiCAtions:

Specifications

Model 1200 Freestanding

Width x Depth

Height with legs

Fire box size (depth x width x height)

Capacity

* Approximate heating area

**E.P.A. output rating

*Duration on low burn 6 -10 hours

30” x 25” (762 mm

x 635 mm)

31.75”

(806mm)

16.1” x 18.25” x

11.15”

(409 mm x 464 mm

x 283 mm)

1.85 feet

(0.0526 meter3)

800 - 1,500 feet

(74.3 - 139.4

meter2)

11,479 to 34,196

BTU/hour

(3,361 to 10,013

watt)

Weight with packaging

E.P.A. Emissions

Rating Label Location Back of Unit

335 lb

(151.95 Kg)

3.3 grams/hour

(0.116 oz/hour)

Table 1: 1200 General Information.

Page 12

Specifications

CleArAnCes to ComBustiBles - 1200 FreestAnding:

MAINTAIN THESE MINIMUM CLEARANCES TO UNSHIELDED COMBUSTIBLES*

Back wall

Side wall

Alcove (48” [1220 mm] Deep)

I Total Width 55” (1397 mm)

J Total Height 78” (1981 mm)

K Top of stove to ceiling 49” (1245 mm)

L Side wall to stove 15” (381 mm)

M Side wall to pipe 24” (610 mm)

N Back wall to unit 12” (305 mm)

O Back wall to pipe 15” (381 mm)

Front

From side wall to side of unit

From rear wall to back of unit

From adjacent wall to corner of unit

From side wall to collar

From rear wall to collar

From adjacent wall to collar

† From door opening to edge of hearth pad

† From side/back of unit to edge of hearth pad

Adjacent wall

Table 2: 1200 Freestanding Clearance to Combustibles.

Front

Single Wall Pipe Double Wall Pipe** Double Wall Pipe

(330 mm)

(279 mm)

(229 mm)

(559 mm)

(356 mm)

(445 mm)

USA 16” (406 mm)

CND 18” (450 mm)

USA 6” (152 mm) CND 8” (200 mm)

13”

11”

9”

22”

14”

17½”

Front

Hearth

13”

(330 mm)

10”

(254 mm)

8”

(203 mm)

22”

(559 mm)

13”

(330 mm)

16½”

(419 mm)

USA 16” (406 mm) CND 18” (450 mm)

USA 6” (152 mm) CND 8” (200 mm)

Alcove Back wall

Alcove Side wall

Front

with Heat Efciency

Shield 50-1088 (Flat

top model only)

13”

(330 mm)

8”

(203 mm)

6½”

(165 mm)

22”

(559 mm)

11”

(279 mm)

15”

(368 mm)

USA 16” (406 mm)

CND 18” (450 mm)

USA 6” (152 mm) CND 8” (200 mm)

Alcove

Top vent out back wall with min. 24” (610 mm) vertical

rise; double wall

14”

(356 mm)

12”

(305 mm)

23”

(584 mm)

15”

(381 mm)

USA 16” (406 mm) CND 18” (450 mm)

USA 6” (152 mm) CND 8” (200 mm)

CAUTION: An uninsulated smoke pipe must not pass through an attic, roof space, closet or similar concealed

space, or through a oor, ceiling, wall, or partition, or any combustible construction.

Page 13

Specifications

† FLOOR PROTECTION: If a stove is installed on a combustible oor, it must have a leg kit with ash box attached

and be on a NON-COMBUSTIBLE hearth pad (see below).

If unit is raised: 0” - 2” (0mm - 51mm); 1” (25mm) non-combustible material with k value = 0.84 or equivalent 2” - 8” (51mm - 203mm); ½” (13mm) non-combustible material with k value = 0.84 or equivalent Greater than 8” (203 mm); Any non-combustible material

* ALL CLEARANCES CAN BE REDUCED WITH SHIELDING ACCEPTABLE TO THE LOCAL AUTHORITY. **DOUBLE WALL: IN CANADA: Any ULC-S629 listed chimney system with the accompanying listed double wall vent connector. IN U.S.A.: Any UL 103 HT listed chimney system with the accompanying listed double wall vent connector.

dimensions - 1200 FreestAnding:

5.50"

(140mm)

25.00"

(635mm)

22.25"

(565mm)

17.00"

(432mm)

31.75"

(806mm)

(254mm)

30.50"

(775mm)

30.00"

(762mm)

10.00"

16.00"

(406mm)

29.125"

(740mm)

Figure 4: 1200 Freestanding Step Top Dimensions.

Page 14

Installation

removAl From pAllet:

• Remove the screws which are securing the shipping brackets to the unit.

• Remove the lag bolts and discard the brackets.

Figure 5: Bolts to remove.

Page 15

Installation

HeArtH proteCtion exAmples:

Table 3: Examples of Hearth Pad Sizing Using Clearances From Table 2 (refer to Figures 6).

Canada USA

1200 1700 1200 1700

(A) Minimum Width 40½” (1028mm) 36½” (926mm)

(B) Minimum Depth

Adjacent

(D) Maximum Back Corners -

Adjacent

(E) Maximum Front Corners -

Diagonal

(F) Maximum Back Corners -

Diagonal

(G) Minimum Width remaining

without corners - Front

(H) Minimum Width remaining

without corners - Back

46”

(1168mm)

OPTIONAL - Corner removal

8¾” (314mm) 6¾” (171mm)

6¼” (160mm) 5⅛” (130mm)

12⅜” (314mm) 9½” (242mm)

8⅞” (227mm) 7¼” (185mm)

23” (583mm) 23” (583mm)

27⅞” (707mm) 26⅛” (665mm)

50½”

(1283mm)

42”

(1067mm)

46½”

(1181mm)

Table 4: Examples of Parallel Installation Using Clearances From Tables 2 (refer to Figure 6).

Model Country

Single Wall Pipe 1200

Double Wall Pipe 1200

Double Wall Pipe with Heat Efciency Shield 50-1088 (Flat top model only)

Top vent out back wall with min. 24” (610mm) vertical rise; double wall

1200

(I) Far Edge of Hearth Pad

to Side Wall - Minimum

Canada 45½” (1156mm) 49¼” (1252mm)

USA 43½” (1104mm) 47¼” (1201mm)

Canada 45½” (1156mm) 48¼” (1226mm)

USA 43½” (1104mm) 46¼” (1175mm)

Canada 45½” (1156mm) 46¼” (1175mm)

USA 43½” (1104mm) 44¼” (1125mm)

Canada 46½” (1181mm) 50¼” (1277mm)

USA 44½” (1129mm) 48¼” (1226mm)

(J) Front of Hearth Pad to

Back Wall - Minimum

Non combustible oor protection must be under the chimney connector and 2 inches (50.8 mm) beyond each side.

Page 16

USA 6"

(152mm)

CND 8"

(203mm)

Installation

H D

USA 6" (152mm)

CND 8" (203mm)

Door Opening

USA 16" (406mm) CND 18" (457mm)

(152mm)

(203mm)

Coverage

USA 6"

CND 8"

Optional

Figure 6: General Parallel Installation

(refer to Tables 11 & 12).

Optional

Coverage

USA 6" (152mm) CND 8" (203mm)

Door Opening

USA 16" (406mm)

CND 18" (457mm)

Optional

Coverage

Figure 7: General Corner Installation (refer to Tables 11 & 13).

Page 17

Installation

3¼”

8⅞”

7⅛”

Diagonal

Removed -

(P) Back Corner

1¼”

(32mm)

(182mm)

(83mm)

(227mm)

4⅞”

Adjacent

Removed -

(O) Back Corner

Pad

30⅝”

(N) Width at

back of Hearth

29⅛”

(M) Edge of

Adjacent Wall

Hearth Pad to

Wall

57⅝”

(L) Adjacent

⅞”

(23mm)

(124mm)

34⅝”

(881mm)

(779mm)

29⅛”

(738mm)

54⅞”

(1393mm)

(1465mm)

2¼”

6¼”

(160mm)

31⅞”

27⅞”

(707mm)

28⅛”

(713mm)

53⅞”

56⅝”

(1439mm)

(59mm)

(809mm)

(713mm)

(1368mm)

Corner

(K) Front of

Hearth Pad to

Table 5: Examples of Corner Installation Using Clearances From Table 2 (refer to Figures 7).

1200 Canada 61⅜”

Single

(1507mm)

(1558mm)

USA 59⅜”

Wall Pipe

1200 Canada 59⅞”

Double

(1471mm)

(1522mm)

USA 57⅞”

Wall Pipe

Page 18

Installation

outside Air kit:

It is mandatory to use outside air for installations in mobile homes. A 4” (10.2 cm) fresh air adaptor kit is available. This kit can be installed on

the back of the Ash Box. If outside air is to be used in conjunction with the convection fan kit, there is a separate outside air adapter which connects to the bottom of the Ash Box. Refer to the Parts List.

Place the ¼” mesh screen behind the fresh air adaptor (as shown to right).

Fresh air connection to the unit must be a non-combustible pipe Example: 4” (10.2 cm) single wall aluminum ex pipe.

Figure 8: Fresh Air Adaptor

reCommended HeigHts And diAmeters For Flue pipe:

The minimum ue pipe height at sea level is 12 feet (3.7 m) straight up from top of the unit. For every 1000 feet (305 m) above sea level, 4% could be added to the overall height. Use Tables 14, 15, and 16 to calculate the required vertical rise required.

Table 6: Recommended Height for Flue Pipe.

Elevation

above sea level

feet 0 2 x 15° 4 x 15° 2 x 30° 4 x 30° 2 x 45° 4 x 45°

0-1000 12.0 12.7 13.3 13.3 14.7 14.0 16.0 1000-2000 12.5 13.2 13.8 13.8 15.3 14.6 16.6 2000-3000 13.0 13.7 14.4 14.4 15.9 15.1 17.3 3000-4000 13.4 14.2 14.9 14.9 16.5 15.7 17.9 4000-5000 13.9 14.7 15.4 15.4 17.1 16.2 18.6 5000-6000 14.4 15.2 16.0 16.0 17.6 16.8 19.2 6000-7000 14.9 15.7 16.5 16.5 18.2 17.4 19.8 7000-8000 15.4 16.3 17.0 17.0 18.8 17.9 20.5 8000-9000 15.8 16.8 17.6 17.6 19.4 18.5 21.1

9000-10000 16.3 17.3 18.1 18.1 20.0 19.0 21.8

meters 0 2 x 15° 4 x 15° 2 x 30° 4 x 30° 2 x 45° 4 x 45°

0-305 3.7 3.9 4.1 4.1 4.5 4.3 4.9 305-610 3.8 4.0 4.2 4.2 4.6 4.4 5.1 610-915 4.0 4.2 4.4 4.4 4.8 4.6 5.3

915-1220 4.1 4.3 4.6 4.6 5.0 4.8 5.5 1220-1525 4.2 4.5 4.7 4.7 5.2 4.9 5.7 1525-1830 4.4 4.6 4.9 4.9 5.4 5.1 5.9 1830-2135 4.5 4.8 5.0 5.0 5.5 5.3 6.0 2135-2440 4.7 4.9 5.2 5.2 5.7 5.5 6.2 2440-2745 4.8 5.1 5.4 5.4 5.9 5.6 6.4 2745-3050 5.0 5.3 5.5 5.5 6.1 5.8 6.6

Minimum recommended ue pipe height for # of elbows

(Note: No more than 2 offsets (4 elbows) can be used. 2x45°=1x90°

We recommend the use of a 6” (150mm) diameter ue pipe. However, the CSA-B365 and the WETT Training Manual state that the ue pipe may be reduced in cross-sectional area provided that the installer ensures sufcient draft is available at the appliance.

Table 7: Distance to add to

overall vertical height.

Part used feet meters

45° elbow 1.0 0.3

90° elbow 2.0 0.6

“T” 3.0 0.9

1 ft (0.3m) of horizontal run

Table 8: Examples of calculating

overall vertical height required.

sea level with 2

x 30° elbows

one “T” 3.0 ft (0.9 m)

1½ ft (0.6 m) horizontal run

Total 1 19.3 ft (5.9 m)

4000-5000 ft

(1220-1525 m)

above sea level

one “T” 3.0 ft (0.9 m)

2 ft (0.6 m)

horizontal run

Total 2 20.9 ft (6.3 m)

Rear of Ash Box

Distance to add

2.0 0.6

Height

13.3 ft (4.1 m)

3.0 ft (0.9 m)

13.9 ft (4.2 m)

4.0 ft (1.2 m)

Page 19

Installation

CHimneY instAllAtion tHrougH wAll:

Here are four (4) methods of combustible wall chimney connector pass-throughs. Information was provided from NFPA 211.

Minimum chimney clearance to brick and combustibles 2 inches (50.8 mm)

Minimum clearance 12 inches (304.8 mm) of brick

Chimney connector

Fire clay liner

Minimum 12 inches (304.8 mm) to combustibles

Chimney Flue

Masonry chimney

Figure 9: Chimney Through Wall - Method A.

Minimum chimney clearance from masonry to sheet steel supports and combustibles 2 inches (50.8 mm)

Non-soluble

Factory-built chimney length

Air space 9 inches (228.6 mm) minimum

refractory cement

Chimney length flush with inside of flue

Masonry chimney

Chimney

flue

Sheet steel supports

Minimum clearance 9 inches (228.6 mm)

Chimney connector

Use chimney manufacturer’s parts to attach

connector securely Solid-insulated, listed factory-built chimney length

Figure 10: Chimney Through Wall - Method B.

Method A. 12” (304.8 mm) Clearance to Combustible Wall Member:

Using a minimum thickness 3.5” (89 mm) brick and a ⅝” (15.9 mm) minimum wall thickness clay liner, construct a wall pass-through. The clay liner must conform to ASTM C315 (Standard Specication for Clay Fire Linings) or its equivalent. Keep a minimum of 12” (305 mm) of brick masonry between the clay liner and wall combustibles. The clay liner shall run from the brick masonry outer surface to the inner surface of the chimney ue liner but not past the inner surface. Firmly grout or cement the clay liner in place to the chimney ue liner.

Method B. 9” (229 mm) Clearance to Combustible Wall Member: Using a 6” (152 mm) inside diameter, factory-built Solid-Pak chimney section with insulation of 1” (25.4 mm) or more, build a wall pass-through with a minimum 9” (229 mm) air space between the outer wall of the chimney length and wall combustibles. Use sheet metal supports, fastened securely to wall surfaces on all sides, to maintain the 9” (229 mm) air space. When fastening supports to chimney length, do not penetrate the chimney liner (the inside wall of the Solid-Pak chimney). The inner end of the Solid-Pak chimney section shall be ush with the inside of the masonry chimney ue and sealed with a non-water soluble refractory cement. Use this cement to also seal to the brick masonry penetration.

Minimum chimney clearance from masonry to sheet steel supports and combustibles 2 inches (50.8 mm)

Two air channels each 1 inch (25.4 mm)

Chimney connector

Minimum 6 inches

Two ventilated air channels each 1 inch (25.4 mm). Construction of sheet steel

Chimney flue

Masonry chimney

(152.4 mm) glass fiber insulation

Sheet steel supports

Figure 11: Chimney Through Wall - Method C.

Method C. 6” (152.4 mm) Clearance to Combustible Wall Member:

Starting with a minimum 24 gauge (.024” [0.6 mm]) 6” (152.4 mm) metal chimney connector and a minimum 24 gauge ventilated wall thimble which has two air channels of 1” (25.4 mm) each, construct a wall pass-through. There shall be a minimum 6” (152.4 mm) separation area containing berglass insulation, from the outer surface of the wall thimble to wall combustibles. Support the wall thimble and cover its opening with a 24 gauge minimum sheet metal support. Maintain the 6” (152.4 mm) space. There should also be a support sized to t and hold the metal chimney connector. See that the supports are fastened securely to wall surfaces on all sides. Make sure fasteners used to secure the metal chimney connector do not penetrate chimney ue liner.

Method D. 2” (50.8 mm) Clearance to Combustible Wall Member: Start with a solid-pak listed factory-built chimney section at least 12” (304 mm) long, with insulation of 1” (25.4 mm) or more, and an inside diameter of 8” (2” [51 mm] larger than the 6” [152.4 mm] chimney connector). Use this as a pass-through for a minimum 24 gauge singlewall steel chimney connector. Keep solid-pak section concentric with and spaced 1” (25.4 mm) off the chimney connector by way of sheet metal support plates at both ends of chimney section. Cover opening, and support chimney section on both sides, with 24 gauge minimum sheet metal supports. See that the supports are fastened securely to

Figure 12: Chimney Through Wall - Method D.

wall surfaces on all sides.

Make sure fasteners are used to secure

chimney ue liner.

NOTES:

1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall pass-through system and the chimney wall, to but not past the inner ue liner face.

2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a oor, or ceiling.

Page 20

Installation

Roof

Ridge

2 ft (0.6 m)

Minimum

3 ft (0.9 m)

Minimum

Within10 ft (3 m)

instAllAtion oF A listed, FACtorY Built CHimneY - FreestAnding:

This is a generic set of instructions; always follow the chimney manufacturer’s instructions explicitly. Also refer to “reCommended HeigHts For Flue pipe”.

1. Set non combustible oor protector and stove in location in accordance with the “ CombustibLes - 1200 Freestanding”.

2. Mark the position for the ceiling hole by suspending a plumb bob from the ceiling over the exact center of your stove ue and mark a spot on the ceiling to indicate the center of the chimney.

3. Move this location, if necessary, to avoid oor joists, ceiling rafters, electrical wiring and plumbing while still maintaining required clearances. If oor joists or ceiling rafters must be cut they must be made structurally sound again. Install chimney according to chimney manufacturers instructions. A chimney connector cannot pass through an attic or roof space, closet or similar

Figure 13: Roof Clearances.

Rain cap/

Spark arrestor cap

Storm Collar

Roof flashing

concealed space, or a oor, ceiling, wall or partition of combustible construction. In Canada, if passage through a wall or partition of combustible construction is

Insulated chimney

Attic radiation shield

desired, the installation shall conform to CAN/CSA-B365 Installation Code for SolidFuel Burning Appliances and Equipment and NFPA 211 Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances.

4. Mark the hole for the outside air kit.

5. Move the stove out of the way.

6. Cut a pilot hole in the ceiling.

Ceiling

Minimum air space in

accordance with

chimney manufacturer.

Radiation shield

Ceiling support

Chimney

connector

7. Cut a hole for the ceiling penetration components and frame in the sides of the hole in both the ceiling and roof. Check, and follow chimney manufacturer’s instructions for all of these steps.

8. Install the support box and chimney through the roof. Install the slip section for the chimney connector.

9. Slip the roof ashing over the chimney and

secure to the roof, being careful to keep the pipe centered in the opening. To meet the code, the chimney must extend above the roof penetration at least 3 feet (91.4 cm), and in any area within 10 feet (304.8 cm) of the

Outside air connection

through wall or floor

Figure 14: Standard Vertical Installation.

CLearanCes to

Roof

Woodstove

Hearthpad

Floor

Page 21

Installation

roof ridge, the chimney must be 2 feet (60.9 cm) above the ridge. Refer to Figure 13.

Note: Increasing the chimney

height above the roof may

Roof radiation

shield (if required)

help your unit to draft better. This greater draft can decrease

Insulated chimney

problems such as difcult start-ups, smoke coming out when door is open, and dirty glass. You may initially try

Ceiling

Minimum

18" (475 mm)

the minimum required height and if problems do arise, add additional height later.

10. Slide the roof ashing over your chimney and seal the ashing to the roof with a

Chimney

connector

roong compound. Secure the roof ashing to your roof with nails or screws.

Woodstove

11. Place the storm collar over the ashing and seal the joints with silicone caulking.

Hearthpad

12. Fasten the rain cap / spark arrestor cap to the top of your chimney.

13. Place the stove back into position.

Floor

Figure 15: Standard Horizontal Installation.

Outside air connection

through wall or floor

14. Install the chimney connector pipe with the lower (crimped) edge of the pipe inside the ue collar. Any creosote formed will then run

back down into the stove. All connections must be tight and secured with three sheet metal screws equally spaced. Double wall pipe is recommended over single wall.

15. Also install an outside air ex pipe to the stove.

Rain cap/

Spark arrestor cap

Storm Collar Roof flashing

Roof

Minimum air space in accordance with chimney manufacturer.

Insulated corner

Wall support

Chase

(optional)

IMPORTANT: When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You must also purchase and install the ceiling support package or wall pass-through and “T” section package, restops (where needed), insulation shield, roof ashing, chimney cap, etc. Maintain proper clearance to the structure as recommended by the manufacturer. The chimney must be the required height above the roof or other obstructions for safety and proper draft operation.

Note: If you are using a horizontal connector (refer to Figure 15), the chimney connector

should be as high as possible while still maintaining the 18” (475 mm) minimum distance from the horizontal connector to the ceiling.

Page 22

Installation

mAsonrY CHimneY instAllAtion - FreestAnding:

DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

A non-combustible oor protector is required under all freestanding units; refer to “CLearanCes to CombustibLes - 1200 Freestanding”. When venting into a masonry chimney, the oor protector must be

installed directly below the chimney vent and 2” (50.8 mm) on either side of the chimney vent.

Vent the stove into a clean, lined, approved masonry chimney in good condition, conforming to local building codes and meeting the minimum standards of the National Fire Protection Association (NFPA). Make sure there are no cracks, loose mortar or other signs of deterioration and blockage. Have the chimney cleaned before the stove is installed and operated, or vent with a listed 6” (150 mm) factorybuilt chimney suitable for use with solid fuels and conforming to ULC-S629 Standard for 650°C factoryBuilt Chimneys in CANADA or UL 103 HT Factory-Built Chimneys for Residential Type and Building Heating Appliances in the U.S.A. Connect the stove to this chimney with a short and straight 6” (150 mm), 24 gauge or heavier, single-wall black or blued steel smoke pipe. Connection to all masonry chimneys must be a metal or masonry thimble cemented in place. All smoke pipes must slope upwards, all connections must be tight and secured with three sheet metal screws equally spaced. The smoke pipe length should not exceed 40% of the chimney height above the stove.

When connecting the stove through a combustible wall to a masonry chimney, additional steps are required. Consult the chimney connector manufacturer and refer to Figure 17.

All chimneys in Canada must be fully lined with a 6" (150 mm) stainless steel liner from the chimney connector to the top of the chimney.

Chimney thimble; non-combustible (cement or metal) and must be cemented in place.

Single or listed double wall chimney connector.

Woodstove

Hearth pad.

Outside air connection

through wall or floor.

Figure 16: Installation into a masonry chimney.

Floor.

Figure 17: Installation into chimney through a

combustible wall.

Page 23

Installation

mAsonrY FireplACe instAllAtion - FreestAnding:

Rain Cap

Chimney

Support and Clamp

Rigid Stainless

Steel Liner

Listed Liner

Stove pipe must

end higher than liner

Flexible Stainless

Steel Section

Steel Plate or Flashing

Damper Removed

or Fastened Open

Unless you are experienced, we recommend installation by your dealer or a professional installer.

Many venting manufacturers have listed kits available to connect a stove to a masonry replace. Always follow the vent manufacturer’s installation instructions.

The existing damper may have to be removed to allow installation.

Stainless Steel Connector Pipe

Clean-out tee

Clean-out

cover

Figure 18: Freestanding Installation into existing replace.

Masonry Fireplace

Floor Protection

Combustible Floor

moBile Home instAllAtion:

SPECIAL REQUIREMENTS: All freestanding installation requirements in “

Factory Built Chimne

y”, must comply with all local codes that may apply, and the following must be met:

VENTING: In Canada: Any ULC-S629 listed chimney system with the accompanying double-wall vent connector. In U.S.A. Any UL-103-HT listed chimney system with the accompanying double-wall vent connector.

Do not connect a listed chimney of one manufacturer with a listed double wall connector from another manufacturer.

These connectors must be installed in accordance with the manufacturer’s instructions. Use only specied components. The chimney and pipe must extend at least 10 feet (2.4 m) above the stove and 3 feet (0.9 m) above the highest point of the roof. Install a rain cap with spark arrestor at the top that will not impede the smoke exhaust. The chimney must be supported at the ceiling or roof so that its weight will not sit on the stove. Seal with silicone to maintain vapor barrier at the chimney and outside air penetrations.

Installation Of A Listed,

Page 24

Installation

Chimney must be removable to allow for transportation of the mobile home.

CAUTION: THE STRUCTURAL INTEGRITY OF THE MOBILE HOME FLOOR, WALL, AND CEILING/ROOF MUST BE MAINTAINED.

OUTSIDE AIR :

Connection from the stoves air intake to the outside is mandatory, (MOBILE HOMES ONLY) either through a hole in the wall not higher than the stoves bottom or through a hole in the oor, using the fresh air adaptor. Avoid cutting any oor joists, wall studs, electrical wiring or plumbing. Seal around the outside air pipe with insulation to prevent drafts. Also install a ¼” mesh rodent or pest screen in the end of fresh-air pipe. Fresh-air connection must be of a non-combustible material, example: 4” (10.16 cm) exible aluminum single wall pipe.

Fresh air could also be supplied from a vented

crawlspace.

The legs must be rmly bolted to the oor using four ¼” bolts. Be sure to replace any insulation or panels removed when fastening the bottom nuts.

If room air starvation occurs because the air intake is blocked with ice, leaves etc., or because the stove door was left open, or due to a strong exhaust fan operating, dangerous fumes could be sucked into the room.

IN SOME AREAS IT MAY BE REQUIRED TO ELECTRICALLY GROUND THE STOVE TO THE STEEL CHASSIS OF THE MOBILE HOME.

When this unit is installed in a Mobile Home it must be grounded to the steel chassis or connected to a grounding rod.

Spark arrestor cap

At least

3 feet (914 mm)

Insulated

chimney

Ceiling

Outside air connection

through wall or floor

Figure 19: Freestanding installation into mobile home.

Roof flashing

Roof

Radiation Shield

Ceiling support

Double wall pipe

Woodstove

Hearthpad

Floor

Bolt stove to floor

Manufactured (Mobile) home installation must be in accordance with the Manufactured Home Construction and Safety Standard, UL 307B, Title 24 CFR, Part 3280 and/or The Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A.

WARNING: DO NOT INSTALL IN SLEEPING ROOM.

Page 25

Installation

model 1200 BriCk plACement & tuBe loCAtions:

COMPLETE THE STOVE AND SMOKE PIPE INSTALLATION BEFORE PLACING THESE BRICKS.

Tube E

Tube D

Tube A

1. Place the three (3) full size bricks along each side of the rebox and one (1) full size brick on either side of the back of the rebox.

2. To place the oor bricks, lay the two (2) partial bricks along the back of the oor. Then on the left, lay two (2) full size

bricks and on the right, lay a full size brick in the center and the half brick in the front (for the ash dump). The spaces between the bricks will soon ll with ashes.

Figure 20: Brick Placement for 1200 shown with Secondary Air Channel

and Tubes.

When replacing bricks, use only pumas type re bricks.

TOTAL BRICKS:

11 - Full size bricks 9” long x 4.5” wide x 1.25” thick (22.9 cm long x 11.4 cm wide x 3.2 cm thick)

2 - Partial bricks 9” long x 3” wide x 1.25” thick (22.9 cm long x 7.6 cm wide 3.2 cm thick)

1 - Half brick 4.5 “ long x 4.5” wide x 1.25” thick (11.43 cm long x 11.43 cm wide x 3.175 cm thick)

Removing Air Tube: If a secondary air tube needs to be removed, place a screwdriver (any style except at head) into one of the air holes and tap it with a hammer/mallet to the left until the right end of the tube is freed. To install a secondary air tube, reverse the above instructions.

IMPORTANT: All secondary air tubes must be in place for proper operation.

Page 26

Installation

C-CAst CerAmiC BAFFle instAllAtion:

1. Slide the right C-Cast Ceramic Bafe in over the secondary air tubes at the top of the rebox. The tab must be on the top and pointing towards the center and the smooth side is to face down.

2. Hook the outside edge of the bafe over the top of the secondary air chamber. This will make room to for the installation of the left C-Cast Ceramic Bafe.

3. Slide the left C-Cast Ceramic Bafe in over the secondary air tubes. The tab must be on the bottom and pointing towards the center and the smooth side is to face down.

4. Pull the bafes together in the middle so the right tab rests on top of the left tab. Ensure the bafes are ush with the back and both sides of the rebox.

Right Ceramic Baffle

Left Ceramic Baffle

Figure 21: Installation of C-Cast Ceramic Bafe.

FAn wiring diAgrAms:

This appliance, when installed, must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.1 CANADIAN ELECTRICAL CODE. Part 1, SAFETY STANDARDS FOR ELECTRICAL INSTALLATIONS, or THE NATIONAL ELECTRICAL CODE ANSI / NFPA 70 in the USA.

CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors

can cause improper and dangerous operation. Verify proper operation after servicing.

DO NOT oil the fan bearings. DO NOT cut or remove the grounding prong from the plug. DO NOT route the power cord beneath the heater.

WARNING: This appliance is equipped with a three-prong (grounding) plug for your protection against

shock hazard and should be plugged into a properly grounded three-prong receptacle.

Page 27

White

Black

White

Installation

Fan

Black

Fan

temperature

sensor

Power Supply

Figure 22: Freestanding Fan Kit Wiring Diagram.

optionAl FAn instAllAtion - FreestAnding:

Refer to Fan Wiring diagram before installing your optional fan kit.

1. Remove the fan assembly from the box and inspect for any damage to the assembly. If damage is noticed call your dealer, distributor or courier company and have components replaced before installing kit.

2. Install the four #10 screws loosely into the bottom of the air cabinet.

3. Align the keyslots of the fan assembly with four screws. Fully bottom the keyslots before tightening the screws

Fan

controller

4. Plug the fan assembly in and check for proper operation.

Figure 23: Back View of Freestanding Unit

with Fan Kit.

Page 28

DISASSEMBLY

removAl oF CAst sides And door:

To remove the cast sides, lift off the Cast Top and then unscrew the slider knob and then remove the two top bolts using a 3/8” socket. The Cast Side may then be lifted up.

The door may be taken off by rst lifting off the Cast Top and then removing the two bolts from the top door hinge, using a 3/8” socket.

door lAtCH Adjustment:

Over time as the door gasket fully compresses to the face of the rebox, it may be necessary to adjust the door latch position to maintain a tight seal. Signs that the door latch may need adjusting are if the door handle feels overly loose when closed, or if you notice air leaks occurring during low burns.

1. Remove the right Cast Side (shown above)

2. Use a 3/8” socket to loosen the two 1/4” bolts and slide the latch slightly back. Retighten the bolts and latch the handle. The handle should provide a bit of resistance and close rmly.

Page 29

Rating Label

Tested & Listed By

Model / Modèle: Kodiak 1200 FS Kodiak 1200 FPI Kodiak 1700 FS Kodiak 1700 FPI

Certified for use in Canada & USA /

Certifié pour installation au Canada et aux Etats-Unis.

Models 1200 and 1700 Freestanding units: SUITABLE FOR MOBILE HOME INSTALLATION Tested to ULC-S627-00, ULC-S628-93 (FPI only), & UL-1482-10. US Environmental Protection Agency, certified to comply July 1, 1990, particulate emission standards.

Install and use only in accordance with the manufacturers installation and operating instructions. Contact local building or fire officials about restrictions and installation inspection in your area. Use 6” (150 mm) diameter minimum 24 MSG black or 25 MSG blued steel connector listed factory-built chimney suitable for use with solid fuels or masonry chimney. See local building code and manufacturer’s instructions for precautions required for passing a chimney through a combustible wall or ceiling. Do not pass chimney connector through a combustible wall or ceiling. Minimum clearances from horizontal connector and ceiling 18” (455 mm). Do not connect this unit to a chimney flue servicing another appliance.

Minimum Clearances to Combustible Materials / Espaces Libres Aux Materiax Combustibles.

Model / Modèle Sidewall to unit / De la paroi latérale au dispositif

Backwall to unit / De la paroi arrière au dispositif

Adjacent wall to corner of unit /

C 9” (229 mm) 6½" (165 mm)

De la paroi adjacent au coin de dispositif Sidewall to connector / De la paroi latérale au connecteur

Backwall to connector / De la paroi arrière au connecteur

Adjacent wall to connector/

De la paroi adjacent au connecteur

† Front of door opening to edge of hearth /

Le devant d'ouverture de porte au bord de coussin de coeur † Side/back of unit to edge of hearth /

Le latérale/arrière de dispositif au bord de coussin de coeur

CAUTION: An uninsulated smoke pipe must not pass through an attic, roof space, closet or similar concealed space, or through a floor, ceiling, wall, or partition, or any combustible construction. † FLOOR PROTECTION: If a stove is installed on a combustible floor, it must have the legs or pedestal attached and be on a NON COMBUSTIBLE hearth pad * ALL CLEARANCES CAN BE REDUCED WITH SHIELDING ACCEPTABLE TO THE LOCAL AUTHORITY. SINGLE WALL: IN CANADA: Any ULC-S629 listed chimney system with the accompanying listed single wall vent connector. IN U.S.A.: Any UL 103 HT listed chimney system with the accompanying listed single wall vent connector. **DOUBLE WALL : IN CANADA: Any ULC-S629 listed chimney system with the accompanying listed double wall vent connector. IN U.S.A.: Any UL 103 HT listed chimney system with the accompanying listed double wall vent connector. DOUBLEWALL IS REQUIRED FOR MOBILE HOME INSTALLATIONS.

**Alcove (Use double wall pipe) / Alcôve (Utilisant le double connecteur de mur)

I Total width / Largeur totale 55” (1397 mm)

J Total height / Hauteur totale 78” (1981 mm) K Top of stove to ceiling / Le sommet de poêle au plafond 49” (1245 mm) L Sidewall to unit / De la paroi latérale au dispositif

Sidewall to connector / De la paroi latérale au connecteur

M 24” (610 mm)

Backwall to unit / De la paroi arrière au dispositif

N 12” (305 mm)

Backwall to connector / De la paroi arrière au connecteur

O 15” (381 mm)

Maximum Depth / Profondeur maximumP 48” (1220 mm) 48” (1220 mm)

Report/Rapport no. 268-S-04b-2 268-S-05b-2 268-S-01-2 268-S-06b-2

Models 1200 and 1700 inserts may be installed as an insert in a masonry fireplace. / On peut encastrer le modèles 1200 et 1700 dans un foyer de maçonnerie.

Model / Modèle 1200 FPI 1700 FPI

A To unshielded side wall / aux mur non protegé 10” (254 mm) 10” (254 mm)

B To an unshielded 8” (203 mm) mantle / aux manteau 8“ non protegé 21” (533 mm) 24” (610 mm) C To top facing (protruding ¾” [19 mm]) clearance / aux revêtement supérieur 17½” (445 mm) 19½” (495 mm) D To side facing (protruding ¾” [19 mm]) clearance / aux revêtement a côté 1” (25 mm) 1” (25 mm)

E † From door opening of unit to edge of floor protection / De ouverture de la porte de l'unité à bord de la protection de plancher USA 16” (406mm) / CND 18” (450mm) F † From side of unit to edge of floor protection / Du côté de l'unité au bord de la protection de plancher USA 6” (152 mm) / CND 8” (200 mm)

OPERATE ONLY WITH DOORS CLOSED. Only open door to feed fire. For use with solid wood fuels only. Do not use any other type of fuel. Do not use grate or elevate-fire build wood fire directly on hearth. Do not overfire. Do not obstruct beneath the heater. If heater or chimney connector glows, you are overfiring. Inspect and clean chimney frequently-under certain conditions of use, creosote buildup may occur rapidly. The provided insulation materials are required for operation. Keep furnishing and other combustibles well away from heater. Replace glass only with 5 mm thick ceramic glass. Optional component for FS: fan, electrical rating 115V, 60 Hz 1 Amp (Part # EFW-261). Combustion air openings are not to be obstructed. Danger: Risk of electrical shock. Disconnect power before servicing unit. Route cord away from heater.

CAUTION:

DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURN. READ NAMEPLATE AND INSTRUCTIONS.

MADE IN CANADA /

FABRIQUE AU CANADA

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

LISTED SOLID FUEL SPACE HEATER / IDENTIFIE COMME UN FOYER A COMBUSTIBLE SOLIDE

Boston 1200 FS 268-S-04b-2

HOT WHILE IN OPERATION.

Venice 1200 FPI Boston 1200 FPI Venice 1700 FPI Boston 1700 FPI 268-S-05b-2 268-S-05b-2 268-S-06b-2 268-S-06b-2

Single wall pipe /

Seul connecteur de mur

1200 13” (330 mm) 14” (356 mm) 11” (279 mm) 8” (203 mm) 12” (305 mm)

22” (559 mm) 22” (559 mm) 23” (584 mm) 14” (356 mm) 11” (279 mm) 15” (381 mm)

17½” (445 mm) 16½” (419 mm)

20” (508 mm) 12” (305 mm)

10" (254 mm)

29” (737 mm) 15” (381 mm)

18½” (470 mm)

Model/Modèle 1200

15” (381 mm)

Modèles 1200 et 1700 items indépendants: UTILISABLES DANS LES MAISONS MOBILES. Testé selon ULC-S627-00, ULC-S628-93 (FPI seulement), & UL-1482-10. États-Unis Environnemental Protection Agence, a certifié pour conformer au Juillet 1, 1990, les normes de particules d'émission.

Ce dispositif doit entre installé et opéré conformément aux instructions d'installation et d'opération du manufacturier contactez le service local de l'inspection des bâtiments ou l'officier pompier concernant les restrictions et l'inspection d'installation dans votre localité. Utiliser des connecteurs répertoriés 24 MSG noir ou 25 MSG en acier bronzée de 6" (150 mm) minimum, et une cheminée de fabrication industrielle, appropriée pour utilisation avec des combustibles solides ou avec une cheminée de maçonnerie. Vérifiez les précautions a prendre exigées parle code local et les instructions du manufacturier concernant les conditions pour passer la cheminée a travers un mur ou un plafond combustible. Net pas installer le connecteur de la cheminée a travers un mur ou un plafond combustible. Espaces libres minimum d'un connecteur horizontal et plafond sont 18" (455 mm) ne pas connecter ce dispositif a un conduit de cheminée qui sert déjà un autre dispositif.

**Double wall pipe /

Double connecteur de mur

1700

1200 1700 1200 1700 1200 1700 13” (330 mm) 13” (330 mm) 13” (330 mm) 13” (330 mm) 10” (254 mm)

8” (203 mm)

22” (559 mm)

Model/Modèle 1700

51” (1295 mm) 72” (1829 mm) 44” (1118 mm)

13” (330 mm) 22” (559 mm)

8” (203 mm)

11” (279 mm)

Adjacent wall / Mur adjacent

L’OPERATION DU POELE DOIT SE FAIRE AVEC LA PORTE FERME. N'ouvrir la porte que pour alimenter le feu. N'utilisez que des combustibles solides. Ne pas utiliser un autre type de carburant. N'employez pas de grille de foyer ou ne surélevez pas le feu. Mettez le bois à brûler directement sur l'âtre. Pour éviter la surchauffeur, ne mettez pas trop de bois. N'obstruez pas les ouvertures d'air comburant. Si le poêle ou le connecteur commencent à luire, vous surchauffez le poêle. Inspectez et nettoyez la cheminée souvent. Dans certaines conditions, le créosoté peut s'accumuler rapidement. Les matériaux d'isolation fournis sont requis pour l'opération.Tenez loin les meubles et d'autres produits combustibles. Ne remplacez le verre qu'avec du verre céramique, 5mm

10” (254 mm)

8½" (216 mm)

22” (559 mm) 13” (330 mm)13” (330 mm)

17” (432 mm) 15” (381 mm)

MISE EN GARDE: Un uninsulated tuyau de fumée ne doit pas passer par un grenier, un espace de toit, le placard ou l'espace dissimulé similaire, ou par un plancher, un plafond, un mur, ou une cloison, ou une construction combustible. † PROTÉGER LE PLANCHER: Si une cuisinière est installée sur un sol combustible, il doit avoir un piédestal attache et être sur un coussinet non- combustible. TOUS “ESPACES LIBRES AUX MATERIAX COMBUSTIBLES” PEUVENT ÊTRE RÉDUITS AVEC PROTÉGEANT ACCEPTABLE À L’AUTORITÉ LOCALE. Seul Connecteur de Mur: Au Canada: Certifiée seul connecteur de mur avec toute systèmes de cheminée listée sous ULC-S629. Aux États-Unis: Certifiée seul connecteur de mur avec toute systèmes de cheminée listée sous UL 103 HT. **Double Connecteur de Mur: Au Canada: Certifiée double connecteur de mur avec toute systèmes de cheminée listée sous ULC-S629. Aux États-Unis: Certifiée double connecteur de mur avec toute systèmes de cheminée listée sous UL 103 HT.

Sid¸e wall / Mur a côté

épais. Équipement en option pour un FS: ventilateur caractéristiques assignées 115V, 60 Hz, 1 Amp (pièce # EFW-261) tenez le câble électrique loin du poêle. Danger: Le risque de choc électrique. Débrancher le dispositif avant d'entretenir. Ouvertures d'air de combustion ne doivent pas être obstrués.

TRÈS CHAUD QUAND ALLUMÉ.

MISE EN GARDE:

NE TOUCHEZ PAS. TENIR LOIS

Double wall pipe with efficiency

shield (Flat top model only) / Double connecteur de mur avec la protection d'efficacité (Le modèle plat seulement

7” (178 mm)

6” (152 mm)

22” (559 mm) 10” (254 mm)

14½” (368 mm)

USA 16” (406 mm) CND 18” (450 mm)

USA 6” (152 mm) CND 8” (200 mm)

DOUBLE CONNECTEUR DE MUR NÉCESSAIRES POUR INSTALLATION DANS LES MAISONS MOBILE.

Back wall/ Mur arrière

Front / Mur avant

† FLOOR PROTECTION / PROTÉGER LE PLANCHER: If unit is raised / Si l'appareil est soulevé: 0” - 2” (0mm - 51mm); 1” (25mm) non-combustible material with k value = 0.84 or equivalent /

1” (25mm) le matériel incombustible avec la valeur de k = 0.84 ou équivalent.

2” - 8” (51mm - 203mm); ½” (13mm) non-combustible material with k value = 0.84 or equivalent /

Greater than/Plus grand que 8” (203 mm) any non-combustible material /

n'importe quel type de matériel incombustible.

Adjacent wall / Mur adjacent

Floor Protection /

Front /

Mur avant

Protection du sol

½” (13mm) le matériel incombustible avec la valeur de k = 0,84 ou équivalent.

LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES. LE CONTACT PEUT CAUSER DES BRÛLURES. LISEZ ATTENTIVEMENT L’ÉTIQUETTE ET LES INSTRUCTIONS.

MANUFACTURED BY /

FABRIQUE PAR

: SHERWOOD INDUSTRIES LTD. 6782 OLDFIELD ROAD, SAANICHTON, BC CANADA

DATE OF MANUFACTURE /

DATE DE FABRICATION:

J F M A M J J A S O N D 2011 2012 2013 2014 2015

Serial No. / No. De Serié:

XXXXXXXXXXX

Top vent out back wall with min. 24” (610mm)

vertical rise; double wall pipe / Donné vent hors

de la paroi arrière avec le min. 24” (610 mm)

l'ascension verticale; double connecteur de mur

11” (279 mm) 13” (330 mm)

16” (381 mm) 15” (406 mm)

Alcove Back wall / Mur d’alcôve a l’arrière

Front / Mur avant

Front /

Alcove Side wall /

Mur d’alcôve a côté

Mur avant

Alcove / Alcôve

C-12430

Page 30

Parts List

Reference # Description Part #

1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001 2 Convection Blower 50-512 3 FPI Fan Controller - 115V EC-039 3 Fan Controller Knob EC-040 4 Domestic power cord - 115V EC-042 5 Boston FS Fan Kit 50-2417 6 Fresh Air Kit (for fan) 50-2440 7 Fresh Air Kit EF-186 8 Boston 1200 FS Cast Top 50-2441

9 Boston 1200 Cast Side Right 50-2443 10 Cast Leg Lip Right 50-2114 11 Boston 1200 FS Cast Side Left 50-2442 12 Side Shelves (Set of 2) 50-1991 13 Cast Leg Lip Left 50-2113 14 Cast Leg 50-2106 15 Boston 1200 Ash Pan 50-2446 16 Boston 1200 Cast Ash Drawer Cover 50-2444 17 1200 C-Cast Ceramic Bafe (1 Piece) 50-1146 18 1200 Secondary Air Tube Rear E 50-1102 19 1200 Secondary Air Tube Middle D 50-1103 20 1200 & 1700 Front Secondary Air Tube A 50-1099 21 Pumice Brick 4.5” x 9” 50-1105 22 Pumice Brick 3” x 9” 50-1104 23 Pumice Bricks - 4½” X 4½” 50-1106 24 1200 & 1700 Right Shield Assembly 50-1145 25 1200 & 1700 Left Shield Assembly 50-1144 26 1200 & 1700 Cast Ash Plug 50-1120 27 Door Gasket - 7 feet (2.13m) EF-168 28 Wood Door Glass Retainer Kit (With Screws) 50-1122 29 Glass with Tape 10-000 30 Boston 1200 Cast Front 50-2445 31 Boston Door Handle Complete 50-2393 32 Woodstove Poker 50-1816

Owner’s Manual 50-2439 Gloves 50-1525

Page 31

Parts Diagram - Freestanding

28 29

Page 32

Warranty

Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the nest materials and is backed by our Exclusive Lifetime Limited Warranty to the original purchaser. With Enviro, you’re not just buying a stove, you’re buying a company with years of unequalled performance and quality.

Limited Lifetime Warranty:

Under this warranty, Sherwood Industries Ltd. covers the stove body and accessories against defects in materials and workmanship, for part repair or replacement for the rst seven (7) years and limited labour for the rst two (2) years to the original purchaser. This Warranty covers: Firebox, Stainless Steel Secondary Air Tubes, Cabinet Sides, C-Cast Ceramic Bafe Bafe, Surround Panels, Pedestals, Legs, Ceramic Glass, Slider Control and Cast Iron Door Assembly against defects. Please see the exclusions and limitation section below as certain restrictions and exclusions apply to this warranty.

Limited Two (2) Year Warranty:

Under this warranty, Sherwood Industries Ltd. covers all electrical components against defects in materials and workmanship, for part repair or replacement for the rst two (2) years and limited labour for the rst two (2) years to the original purchaser. Please see the exclusions and limitation section below as certain restrictions and exclusions apply to this warranty.

Limited One (1) Year Warranty:

Under this warranty, Sherwood Industries Ltd. covers all exterior surface nishes against defects in materials and workmanship, for part repair or replacement and limited labour for the rst year to the original purchaser. Please see the exclusions and limitation section below as certain restrictions and exclusions apply to this warranty.

How the Warranty Works

1. All warranties by the manufacturer are set herein and no claim shall be made against the manufacturer on any oral warranty or representation. All claims under this Limited Warranty must be made in writing by your dealer.

2. Any stove or part thereof that is repaired or replaced during the Limited Warranty period will be warranted under the terms of the Limited Warranty for a period not exceeding the remaining term of the original Limited Warranty or six (6) months, whichever is longer.

3. For any part or parts of this stove, which in our judgment show evidence of defects, Sherwood Industries Ltd. reserves the option to repair or to replace the defective product through an accredited distributor or agent, provided the defective part is returned to the distributor or agent, transportation prepaid, if requested. Sherwood Industries Ltd. may chose to buy back the item at the cost the dealer was invoiced.

4. If you discover a problem that you think may be covered by the Limited Warranty, you MUST REPORT it to your Enviro dealer WITHIN 30 DAYS, giving them proof of purchase and the date of purchase. The dealer will investigate the problem and work with Sherwood Industries Ltd. to determine whether the problem:

a) Is covered by the Limited Warranty or b) Can be xed in your home or does the product need to be returned to Sherwood Industries Ltd.

for repair.

5. If Sherwood Industries Ltd. determines that the stove needs to be returned to Sherwood Industries

Ltd. for repair, the customer has the responsibility and the expense of removing it from their home and shipping it to Sherwood Industries Ltd. If the problem is covered by the Warranty, Sherwood Industries Ltd. will replace the item at their discretion and the customer will be responsible for return shipping and re-installation in their home.

Page 33

Warranty

6. If the problem is not covered by the Limited Warranty, the customer will be responsible for all repair costs, as well as all storage, shipping and the cost of removing and re-installing the stove.

If you are not satised with the service provided by the Enviro dealer, write to Sherwood Industries Ltd. at the address listed on the last page of the Owner’s Manual. Include the date you bought the product and a description of the problem.

Exclusions and Limitations:

1. This Warranty does not cover tarnish, discoloration or wear on the plating or paint.

2. This Warranty does not cover gasket material.

3. A qualied installer must install this stove. This Limited Warranty covers defects in materials and

workmanship only if the product has been installed in accordance with local building and re codes; in their absence refer to the owner’s manual. If the product is damaged or broken as a result of any alteration, willful abuse, mishandling, accident, neglect, or misuse of the product, the Limited Warranty does not apply.

4. The stove must be operated and maintained at all times in accordance with the instructions in the

Owner’s Manual. If the unit shows signs of neglect or misuse, it is not covered under the terms of this Warranty policy. Performance problems due to operator error will not be covered by the Limited Warranty policy.

5. As this is a heating appliance, some changes in colour of surface nishes may occur. This is not a aw

and as such is not covered under this warranty.

6. Some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and

not a defect and, therefore, is not covered under this Limited Warranty.

7. Misuse includes over-ring. This will result if the stove is used in such a way that one or more of the

plates glows red. Over-ring can be identied later by warped plates and paint pigment being burnt off. Over-ring this appliance can cause serious damage and will nullify the Limited Warranty.

8. The Limited Warranty will cover glass thermal breakage only and will not cover misuse of the stove

glass, including but not limited to: a) Glass that is struck, has surface contaminates or has had harsh or abrasive cleaners used on it. b) If the door is slammed or is closed while wood in the rebox is protruding out the stove opening thus

striking the glass.

9. This warranty does not cover products made or provided by other manufacturers and used in

conjunction with the operation of this stove without prior authorization from Sherwood Industries Ltd.

The use of such products may nullify the Limited Warranty on this stove. If unsure as to the extent of

this Limited Warranty, contact your authorized Enviro dealer before installation.

10. Sherwood Industries Ltd. will not be responsible for inadequate performance caused by environmental

conditions.

11. The Limited Warranty does not cover installation and operational related problems such as use of

downdrafts or spillage caused by environmental conditions. Environmental conditions include but are not limited to nearby trees, buildings, roof tops, wind, hills, mountains, inadequate venting or ventilation, excessive offsets, negative air pressures or other inuences caused by mechanical systems such as furnaces, fans, clothes dryers etc.

Page 34

Warranty

12. The Limited Warranty does not cover damage caused by burning salt-saturated wood, corrosive driftwood, chemically treated wood or any fuel not recommended in the Owner’s Manual (use cord wood only).

The Limited Warranty is void if: a) The stove has been operated in atmospheres contaminated by chlorine, uorine or other damaging

chemicals.

b) The stove is subject to submersion in water or prolonged periods of dampness or condensation. c) Any damage to the unit, combustion chamber or other components due to water, or weather

damage which is the result of, but not limited to, improper chimney/venting installation.

d) Salt air in coastal areas or high humidity can be corrosive to the nish; these environments can

cause rusting. Damage caused by salt air or high humidity is not covered by the Limited Warranty.

13. Exclusions to the Limited Warranty include: injury, loss of use, damage, failure to function due to accident, negligence, misuse, improper installation, alteration or adjustment of the manufacturer’s settings of components, lack of proper and regular maintenance, alteration, or act of God.

14. The Limited Warranty does not cover damage caused to the stove while in transit. If this occurs, do not operate the stove and contact your courier and/or dealer.

15. The Limited Warranty does not extend to or include paint, door or glass gaskets or rebricks damage caused by normal wear and tear, such as paint discoloration or chipping, worn or torn gaskets, chipped or cracked rebrick, etc.

16. The Limited Warranty does not include damage to the unit caused by abuse, improper installation, or modication of the unit.

17. Damage to plated surfaces caused by ngerprints, scratches, melted items, or other external scores and residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this warranty.

18. The Limited Warranty does not cover tarnish, discoloration or wear on the plated surfaces.

19. Sherwood Industries Ltd. is free of liability for any damages caused by the stove, as well as inconvenience expenses and materials. The Limited Warranty does not cover incidental or consequential damages.

20. The Limited Warranty does not cover any loss or damage incurred by the use or removal of any component or apparatus to or from the Enviro stove without the express written permission of Sherwood Industries Ltd. and bearing a Sherwood Industries Ltd. label of approval.

21. Any statement or representation of Enviro products and their performance contained in Enviro advertising, packaging literature, or printed material is not part of the Limited Warranty.

22. The Limited Warranty is automatically voided if the stove’s serial number has been removed or altered in any way. If the stove is used for commercial purposes, it is excluded from the Limited Warranty.

23. No dealer, distributor, or similar person has the authority to represent or warrant Enviro products beyond the terms contained within the Limited Warranty. Sherwood Industries Ltd. assumes no liability for such warranties or representations.

24. Sherwood Industries Ltd. will not cover the cost of the removal or re-installation of the stove, hearth, facing, mantels, venting or other components.

25. Labour to replace or repair items under this Limited Warranty will be covered per our warranty service fee reimbursement schedule. Labour rates are set per component and as such total labour costs may not be covered.

Page 35

Warranty

26. Sherwood Industries Ltd. is not liable for freight or labour on any stove replaced in-eld and is not liable for travel costs for service work. In the event of in-home repair work, the customer will pay any in-home travel fees or service charges required by the Authorized Dealer.

27. At no time will Sherwood Industries Ltd. be liable for any consequential damages which exceed the purchase price of the unit. Sherwood Industries Ltd. has no obligation to enhance or modify any stove once manufactured (example: as a stove evolves, eld modications or upgrades will not be performed).

28. This Limited Warranty is applicable only to the original purchaser and it is non-transferable.

29. This warranty only covers Enviro products that are purchased through an authorized Enviro dealer.

30. If for any reason any section of the Limited Warranty is declared invalid, the balance of the warranty remains in effect and all other clauses shall remain in effect.

31. The Limited Warranty is the only warranty supplied by Sherwood Industries Ltd., the manufacturer of the stove. All other warranties, whether express or implied, are hereby expressly disclaimed and the purchaser’s recourse is expressly limited to the Limited Warranty.

32. Sherwood Industries Ltd. and its employees or representatives will not assume any damages, either directly or indirectly, caused by improper usage, operation, installation, servicing or maintenance of this stove.

33. Sherwood Industries Ltd. reserves the right to make changes without notice. Please complete and mail the warranty registration card and have the installer ll in the installation data sheet in the back of the manual for warranty and future reference.

34. Sherwood Industries Ltd is responsible for stocking parts for a maximum of seven (7) years after discontinuing the manufacture or incorporation of the item into its products. An exception to this would be if an OEM supplier is not able to supply a part.

Page 36

Installation Data Sheet

The following information must be recorded by the installer for warranty purposes and future reference.

NAME OF OWNER:

_________________________________________

ADDRESS:

_________________________________________

PHONE:___________________________________

MODEL:___________________________________

SERIAL NUMBER:___________________________

DATE OF PURCHASE: ______________(dd/mm/yyyy)

NAME OF DEALER:

_________________________________________

ADDRESS:

_________________________________________

PHONE:___________________________________

NAME OF INSTALLER:

_________________________________________

DATE OF INSTALLATION:___________(dd/mm/yyyy)

INSTALLER’S SIGNATURE:

_________________________________________

MANUFACTURED BY:

SHERWOOD INDUSTRIES LTD.

6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3

www.enviro.com

May 26, 2011

ADDRESS:

_________________________________________

PHONE:___________________________________

C-12426

Enviro Boston 1200-C Free Standing, Boston 1200-C, Boston 1700C, Boston 1200FS, Boston 1700FS Owner's Manual

Specifications and Main Features

Frequently Asked Questions

User Manual