Enviro 1200 KI FPI, 1700 KI FPI Installation And Operation Manual

Download

INSTALLER: LEAVE THIS MANUAL WITH THE WOOD STOVE.

Tested & Listed By

Portland

Oregon USA

OMNI-Test Laboratories, Inc,

O-

T L

Version française: www.enviro.com/fr

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

WOOD STOVE INSERT

Models: 1200 KI FPI & 1700 KI FPI

INSTALLATION AND

OPERATION MANUAL

WARRANTY REGISTRATION

enviro.com/warranty

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS WOOD BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.

CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS, OR THE AUTHORITY HAVING JURISDICTION ABOUT RESTRICTIONS AND INSTALLATION INSPECTION REQUIREMENTS IN YOUR AREA.

THIS HEATER MEETS THE U. S. ENVIRONMENTAL PROTECTION AGENCIES EMISSION LIMITS FOR WOOD HEATERS SOLD AFTER JULY 1ST, 1990. UNDER SPECIFIC CONDITIONS THIS HEATER HAS BEEN SHOWN TO DELIVER HEAT AT RATES RANGING FROM 11,479 TO 34,196 BTU PER HOUR FOR THE 1200 AND FROM 9,425 TO 31,780 BTU PER HOUR FOR THE 1700. THESE STOVES HAVE BEEN

Report # 268-S-05-2, 268-S-06c-2

CERTIFICATION TESTED TO STANDARDS UL-1482-11, AND ULC-S628-93. CERTIFICATION TESTING AND LISTING COMPLETED BY OMNI TEST LABS.

50-2910

Table of Contents

Safety Precautions..........................................................................................3

Operating Instructions.....................................................................................4

Building Your Fire.................................................................................5

How It Works......................................................................................9

Speci• cations................................................................................................10

Air Control.........................................................................................10

General Speci• cations........................................................................10

Clearances To Combustibles - 1200 KI Insert.........................................11

Clearances To Combustibles - 1700 KI Insert.........................................12

Dimensions - 1200 KI Insert.................................................................13

Dimensions - 1700 KI Insert.................................................................14

Installation...................................................................................................15

Removal From Pallet..........................................................................15

Modi• cations For Installation with 19” (483mm) High Lintel...........15

Masonry Fireplace Installation.............................................................16

Installation Using A Block-Off Plate For USA Only..................................19

Model 1200 KI Brick Placement & Tube Locations.................................21

Model 1700 KI Brick Placement & Tube Locations..................................22

C-Cast Ceramic Baf• e Installation........................................................23

Fan Wiring Diagrams..........................................................................24

Fan Removal......................................................................................24

Removal of Top..................................................................................25

Installation Of The Surround Panel......................................................25

Rating Label.................................................................................................26

Parts List......................................................................................................27

Parts Diagram...............................................................................................28

Warranty......................................................................................................29

Installation Data Sheet...................................................... ............................30

Safety Precautions

PLEASE READ THIS ENTIRE MANUAL BEFORE YOU INSTALL AND USE OF YOUR NEW WOOD BODILY INJURY OR EVEN DEATH. BE AWARE THAT LOCAL CODES AND REGULATIONS MAY OVERRIDE SOME ITEMS IN THIS MANUAL. PLEASE CHECK WITH YOUR LOCAL BUILDING

OR FIRE AUTHORITY.

• This appliance becomes extremely hot when in use and can cause burns if contacted.

•

• Make sure you have incorporated proper safety measures to protect infants/toddlers from touching hot surfaces.

• Even after the appliance is out, the ! rebox and glass will remain hot for an extended period of time.

• If this appliance is not properly installed, operated, and maintained a serious house ! re could result.

• Installation of appliance must be completed by a certi! ed installer.

• Wear protective gloves and safety glasses during installation, sheet metal edges may be sharp.

• Do not operate without fully assembling all components.

• Do not use any makeshift materials during installation, maintenance, or replacement.

• Any changes or alterations to this appliance are dangerous and prohibited.

• This appliance has been designed to burn dried and seasoned hardwoods.

• Do not use chemical " uids to start or re-fresh the ! re.

• Do not burn coal, charcoal, or treated wood as there is danger of carbon monoxide being produced.

• Do not burn garbage or " ammable " uids such as gasoline, grease, naphtha or engine oil.

• Never let the stove become hot enough to get any part glowing red.

• Do not operate with door open, door must be tightly closed.

• Do not strike or slam shut the ceramic glass door, if the door glass is broken or a gasket is missing or damaged

• At least 12 square inches (77.4 cm2) of fresh outside air should be admitted into the room or directly to the

• Do not burn wet unseasoned wood, this can causes excessive creosote accumulation. When this is ignited it

• Do not use grates, andirons or any other methods to support or raise the ! re up off the ! re bricks.

• Do not place clothing, furniture, draperies, or any other "ammable materials on or near the appliance.

• Objects placed in front of the appliance must be kept at least of 48” away from the front face of the appliance.

• Do not connect appliance to a chimney "ue pipe servicing another solid fuel burning appliance.

• Do not install in a mobile home this appliance is not Certi! ed for that application.

• Do not attach to any kind of heat distribution ducting system.

• The chimney must be sound and free of cracks. Clean your chimney a minimum of twice a year and as required.

• Your appliance requires periodic maintenance and cleaning. Failure to maintain your appliance may lead to

• A chimney connector shall not pass through an attic, roof space, " oor, ceiling, closet or similar concealed space.

• Do not store wood within appliance installation clearances or within the space required for refueling and ash

• Ashes must be disposed in a metal container with a tight lid and placed on a non-combustible surface well away

• Ensure proper clearances to combustibles are maintained when building a mantel or shelves above the appliance.

STOVE. FAILURE TO FOLLOW INSTRUCTIONS MAY RESULT IN PROPERTY DAMAGE,

Young children should be carefully supervised when they are in the same room as the appliance.

appliance must be repair by a quali! ed service technician before resuming use.

stove through a 4 inch (10.16 cm) diameter pipe.

can cause a chimney ! re that may result in a serious house ! re.

smoke spillage in your home.

removal.

from the home or structure until completely cool.

IMPORTANT: The following must be done to ensure proper operation. Failure to do so will cause extreme overheating and possible personal injury or property damage. If an outside air supply has not been added to this appliance, please ensure that the 4” inch fresh air inlet on the back of the pedestal is removed. Also ensure the ash plug is installed in the ﬁ rebox.

Operating Instructions

FIRST START

When • rst installed, the chimney, • rebricks and steel are cold and it usually takes several hours on a high burn for them to become hot and dry enough for the stove operate at maximum ef• ciency. We recommend during the • rst burn that a door or window is opened to vent the smoke and fumes created while the paint cures. The paint should be completely cured after the • rst few burns.

DISPOSAL OF ASHES:

If you let the ashes accumulate two or three inches on the ﬂ oor of the Firebox they tend to burn themselves up. Fireplace inserts do not have an ash drawer so eventually the ashes will need to be scooped into a metal container with a tightly ﬁ tting lid. Place the closed container on a non-combustible surface, well away from combustible materials.

If the ashes are to be buried in soil or otherwise locally dispersed, keep them in a closed container until all cinders have completely cooled. Small amounts of wood ash can be used in the garden or compost.

FAN OPERATION:

All insert models have been approved for operation with the fans supplied by the manufacturer. During a medium or high burn, using a fan will increase the heat transfer and circulation. Route the power supply cord along the ﬂ oor behind or away from the stove where it will remain cool.

1. Plug the fan assembly into a standard three (3) prong grounded electrical receptacle.

2. There is a three position switch located on the fan pod. The auto/off/manual rocker switch allows the fan to be turned on manually, or automatically. When this switch is up it is set to the manual position. The center position is off. When the switch is pushed down it is set to the automatic position.

3. In the manual position the Rotary Rheostat knob is used to turn the fan on and off as well as adjust the ﬂ ow.

4. In the automatic position the fan will automatically turn on once the fan temperature sensor reaches the operating temperature. When the unit cools down, the fan temperature sensor will shut the fan off. You should set the desired ﬂ ow while in the manual position.

REPLACING THE GLASS:

Never strike or slam the door, hit the glass or let burning wood rest against it. If the glass cracks when the ﬁ re is burning, do not open the door until the ﬁ re is out. Do not operate the stove again until the glass has been replaced. If the glass is damaged in any way, a factory replacement is required (see “PARTS LIST”). To replace the glass, remove the steel retainer and all loose glass. Replace only with Neoceram

mm glass 16 ⅝” (422 mm) x 10 ⅝” (270 mm) and wrap the edges with ⅛” (3.2 mm) x ½” (13 mm)

5 self-adhesive ﬁ berglass gasket, see parts list for part number.

Wear protective gloves when handling damaged glass door assembly to prevent personal injury. When the glass door assembly is being transported, it must be wrapped in newsprint and tape and/or a strong plastic bag. Replacement glass must be purchased from an ENVIRO dealer. No substitute

materials are allowed.

FIRE EXTINGUISHER AND SMOKE DETECTION:

All homes with a solid fuel burning stove should have at least one ﬁ re extinguisher in a central location known to all in the household and a smoke detection devise in the room containing the stove. If it sounds the alarm, correct the cause but do not deactivate. You may choose to relocate the smoke detection devise within the room; DO NOT REMOVE THE SMOKE DETECTOR FROM THE ROOM.

Operating Instructions

CREOSOTE - ITS FORMATION AND REMOVAL:

When wood is burned slowly, it may produce tar and other vapors that, combined with moisture, form

creosote. These creosote vapors condense in the relatively cool chimney • ue of a slow burning • re and, if ignited, make an extremely hot • re. Therefore, the smoke pipe and chimney should be inspected at least once every two months during the burning season. If creosote has accumulated it should be removed to reduce the risk of a chimney • re.

MAINTENANCE:

At the end of each heating season your chimney and the smoke pipe will need to be professionally cleaned. If soot has accumulated above the top baf• e they will need to be removed and cleaned. If Baf• es are damaged they need to be replaced. If the secondary air tubes are badly eroded or warped, replace them. Replace worn door gaskets and broken bricks as needed.

FAILURE TO INSPECT AND CLEAN YOUR CHIMNEY SYSTEM REGULARLY CAN RESULT IN A CHIMNEY FIRE, WHICH COULD DAMAGE THE CHIMNEY OR CAUSE A HOUSE FIRE.

CHIMNEY OR RUN AWAY FIRE:

1. Alert and evacuate all people inside the home. You should an evacuation plan in place for such an

event as well as a safe place to meet.

2. Fully close the Air Damper to limit oxygen to the • re.

3. Call local • re department (or dial 911). Have a • re extinguisher and a garden hose ready, your local

• re authority will provide you with instructions to handle the situation.

4. Once the • re is out examine the • ue pipes, chimney, attic, and roof of the house, to see if any part has become damaged by the • re.

4. Do not operate the stove again until the chimney and its lining have been cleaned and you are certain they have not been damaged. We strongly recommend inspection by a WETT (Wood Energy Technical Training) certi• ed installer in Canada or a HEARTH (Hearth Education Foundation) certi• ed installer in the U.S.A. before starting another • re.

BUILDING YOUR FIRE:

Proper operation of your stove will help to ensure safe, ef• cient heating. Please take a few moments to review these simple operating procedures.

IMPORTANT: Please be aware when loading your stove that the air tubes in the rear are lower than the front.

1. Fuel Selection:

This stove is designed to burn natural wood only. Higher ef• ciencies and lower emissions generally result when burning air dried seasoned hardwoods, as compared to softwoods or to green freshly cut hardwoods. Wood should be properly air dried (seasoned) for at least six months, a year is preferred. Wet or freshly cut wood will cause the • re to smolder creating creosote. Wet wood also creates very little heat and • res tend to go out.

DO NOT BURN: treated wood, salt water wood, coal, charcoal, garbage, plastic, solvents, or colored papers. These material contain chlorides which will rapidly corrode and warp metal surfaces which voids warranty.

Operating Instructions

2. Building/Maintaining a Fire:

a) Open the primary air slide by pulling it all the way to the right. b) Place a base of crumpled uncolored paper in the bottom of the stove. Lay pieces of kindling on top of

the newspaper and light it.

CAUTION: “Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter ! uid,

or similar liquids to start or “freshen up” a " re in this heater. Keep all such liquids well away from heater while it is in use.

c) As the kindling begins to burn, add several slightly larger pieces of wood until the ! re is burning well.

Once a coal bed had been established regular size logs may be added. NOTE: Until the ! re is burning well, leave the air control fully open.

d) Regulate the heat output and duration of burn by adjusting the air controls to allow a larger ! re and

vice versa. A short period of experimentation with the control settings will allow you to regulate the

heat output to keep your home comfortable.

Do not use a grate or elevate the " re. Build " re on top the bricks inside the " rebox.

3. Refueling the Stove:

Use a long pair of ! reproof gloves to protect your arms from burns when loading wood. Keep a small steel shovel and poker nearby for moving a log, lifting a fallen ember, and for keeping the hearth clean.

a) Before attempting to add fuel to the stove fully open the damper by pulling it all the way to the right and slowly open the door. This allows the chimney to carry away the additional smoke and keep it from entering the house.

b) DO NOT OVERLOAD THE STOVE. Normally, three or four logs will provide heat for several hours. There should never be any part of the stove glowing red hot when operating properly.

c) DO NOT OVERFIRE. If any part of the stove or chimney connector glows, you are over! ring. ww) CAUTION: DO NOT PLACE FUEL WITHIN SPACE HEATER INSTALLATION CLEARANCES OR WITHIN

THE SPACE REQUIRED FOR ASH REMOVAL.

4. For Maximum Ef" ciency:

When the stove is hot, load it fully to the top of the door opening and burn at medium low settings. When the fuel is mostly consumed, leaving a bed of red coals, repeat the process. Maximum heat for minimum fuel occurs when the stove top temperature is between 250°F (120°C) and 550°F (290°C).

Helpful Hints Worth Repeating

1. Helpful advice on the correct way to start your " re.

a) You will need small pieces of dry wood, called kindling, and paper. Use only newspaper or paper

that has not been coated or had other materials glued or applied to it. Never use coated (typically advertising " yers) or coloured paper.

b) Always fully open the air control damper and slowly open wood stove door to prevent suction and

drawing smoke into the room.

c) Crumple several pieces of paper and place them in the center of the ! rebox directly onto the ! rebricks.

Never use a grate or andirons to elevate the ! re.

Operating Instructions

d) Place small pieces of dry wood (kindling) over the paper in a criss cross manner. This allows for good

air circulation, which is critical for good combustion.

e) Light the crumpled paper in 2 or 3 locations.

Note: It is important to heat the air in the stovepipe for draft to start.

f) Fully open the air controls of the wood stove and close the door until it is slightly open, allowing for

much needed combustion air to be introduced into the ! rebox. Never leave the door fully open, as sparks from the kindling may " y out of the stove, causing damage or injury. As the ! re begins to burn the kindling, some additional kindling may be needed to sustain the ! re. DO NOT add more paper after the ! re has started.

g) Once the kindling has started to burn, add some smaller pieces of seasoned ! rewood. Note: Adding

large pieces at the early stages will only serve to smother the ! re. Continue adding small pieces of seasoned dry ! rewood, keeping the door slightly open until each piece starts to ignite. Remember to always open the door slowly when placing wood into the ! re.

h) Once the wood has started to ignite and the smoke has reduced, close the wood stove door fully. The

reduction of smoke is a good indication that the draft in the chimney has started and good combustion is now possible. Larger pieces of seasoned, dry ! rewood can now be added when there is suf! cient space in the ! rebox. Adjust the air control setting to desired setting.

Note: The lower the air control setting, the longer the burn time of your ﬁ rewood.

2. What type of wood is best to use as ﬁ rewood?

Both hardwood and softwood burn well in this stove. Both woods contain about 8,000 BTU/lb (18,570 KJ/Kg), but hardwood is generally more dense, will weigh more per cord, and burns a little slower and longer. Cutting ! rewood so that it will ! t horizontally, front to back, makes it easier loading and less likely for the fuel to roll on to the glass. Except for a cold start, there is no need to crisis-cross the logs. Ideal length for the logs used in the 1200 would be about 16“ (381 mm) but it can burn pieces up to 18” long. Ideal length for the logs used in the 1700 would be about 18“ (381 mm) but it can burn pieces up to 20” long logs. Burn only seasoned wood, It produces more heat and less soot or creosote. Freshly cut wood has about 50% moisture. A 10 pound (4.5 Kg) log contains 5 pounds (2.3 Kg) of water. Burn beach wood only if its salt content has been washed away in a season of rain and then the dried again.

3. What does dry, seasoned wood mean?

Wood that has been dried for a period of one year in a well-ventilated and sheltered area would be considered dry, seasoned wood. Wood from slow-growing trees is generally considered better than wood from fast-growing trees. To season ! rewood, split and stack it so that air can get to all parts of the wood.

4. Will following the above-listed steps for starting a ﬁ re mean perfect results every time?

The quick answer is ‘most of the time’. There are many variables that may affect your success when starting a ! re. Most of those variables and how to deal with them will be learned through experience. Your ability to start a good ! re will signi! cantly increase with time and patience. Some of the reasons for poor stove performance will be covered in the next section of these instructions.

5. Why won’t my ﬁ re light?

Damp or wet wood and a poor draft are the main reasons for poor results in starting a ! re. Always use dry, seasoned wood for your ! re. Even wood dried for two years will be dif! cult to ignite if it has become wet from rain.

Operating Instructions

6. Is it normal for soot to cover the glass at the beginning of a • re?

Your stove has been built with an air-wash system that will help keep the glass clear when the ! rebox has reached a good operating temperature and has a good draft. Normally a hot stove will keep the glass clean. If you must clean the glass, use a soft non abrasive cloth and clean with water when unit is cold. Cold ! rebox temperature and poor draft cause sooting of the glass. Once the ! rebox temperature and the draft increase, the soot should burn off.

7. What is draft?

Draft is the ability of the chimney to exhaust or draw smoke produced during the normal combustion process. Too much draft may cause excessive temperatures in the appliance and may damage the appliance. Inadequate draft may cause back puf! ng or “plugging” of the chimney. There is a certain amount of draft that is required to allow for your stove to function at its’ highest ef! ciency. A water column reading of 0.1” or more is recommended.

8. What can cause a poor draft?

The most common factors for poor draft are: a) Lack of supply air

b) Environmental conditions c) Cold chimney temperature d) Poor chimney installation and maintenance e) Atmospheric pressure

a) Air supply – Inside the home, normal household appliances such as clothes dryers and forced-air

furnaces compete for air, resulting in air starvation to the wood stove. This creates a condition in the house known as negative pressure. When a house experiences negative pressure, the combustion gases can be drawn from the chimney and into the house. This condition is commonly referred to as down-drafting. Increased amounts of insulation, vinyl windows, extra caulking in various places and door seals can all keep heat in but may also make a home too airtight. An easy way to stop negative pressure in a home is to crack a window in the room containing the stove.

b) Environmental Conditions - High trees, low-lying house location such as in a valley, tall buildings or

structures surrounding your house and windy conditions can cause poor draft or down drafting.

c) Cold Chimney Temperature - Avoid cold chimney temperatures by burning a hot ! re for the ! rst ! fteen

to forty minutes, being careful not to over-! re the stove. If any part of the chimney or parts of the stove start to glow, you are over-! ring the stove. If possible,

d) Chimney Installation and Maintenance - Avoid using too many elbows or long horizontal runs. If your

chimney is too short it can cause dif! cult start-up, dirty glass, reduced heat, and down drafting when door is open. Too tall a chimney may prompt excessive draft, which can result in very short burn times and excessive heat output. If in doubt, contact a chimney expert and/or chimney manufacturer for help. To reduce the chance of draw issues and chimney ! res regularly clean the chimney, rain cap, and spark arrestor.

Note: These instructions are intended as an aid and do not supercede any local, provincial or state

requirements. Check with of! cials or authorities having jurisdiction in your area.

HOW IT WORKS:

Exhaust Smoke

/2" Ceramic baffle;

reflects heat down

to burn the particles

in the smoke.

Secondary air tubes; creates a second burn on the particles in the

smoke for a more efficient

& cleaner burn.

Convection Heat

Radiant Heat

Primary air; window

air wash (cooler air to

keep the glass clean).

Pilot air through

Twin pilot

injection ports.

Slider plate; used

for air flow control.

Intake air.

Seasoned Firewood

Exhaust Smoke

/2" Ceramic baffle;

reflects heat down

to burn the particles

in the smoke.

Secondary air tubes; creates a second burn on the particles in the

smoke for a more efficient

& cleaner burn.

Convection Heat

Radiant Heat

Primary air; window

air wash (cooler air to

keep the glass clean).

Pilot air through

Twin pilot injection ports.

Slider plate; used

for air flow control.

Intake air.

Seasoned Firewood

Operating Instructions

Figure 1: 1200 KI Air Flow Path.

Figure 2: 1700 KI Air Flow Path.

Specifications

AIR CONTROL:

The amount of combustion air going to the air wash and pilot is controlled by the air control rod located on the right side of the unit. To increase your air pull the rod out, and to decrease push the rod in. All

Enviro wood stoves have a secondary air that ! ows through the stainless tubes at the top of the " rebox just below the baf! es.

Pull this control all the way out when " rst starting the stove. Once the " re has been established you may adjust this control to set the burn rate of the " re. If this damper is closed at " rst start-up, the " re will burn very slowly and could soot the appliance.

When shutting down the stove, fully open the air control. This allows the chimney temperatures to remain as high as possible for as long as possible. Cold chimney temperatures create creosote.

Figure 3: Air Control Rod.

Pull out - Increase Push in - Decrease

GENERAL SPECIFICATIONS:

Table 1: 1200 KI & 1700 KI General Information.

Model 1200 Insert 1700 Insert

Width x Depth

Height of body 19” (483 mm) or 19.5” (495 mm)

Fire box size (depth x width x height)

Capacity

* Approximate heating area

(409 mm x 464 mm x 283 mm)

27” x 22.5”

(686 mm x 572 mm)

16.1” x 18.25” x 11.15”

1.85 feet

(0.0526 meter3)

2200 feet

(205 meter2)

20.65” x 18.25” x 11.95”

(525 mm x 464 mm x 304 mm)

2.5 feet3 (0.0708 meter3)

27” x 27”

(686 mm x 686 mm)

3000 feet

(280 meter2)

**E.P.A. output rating

*Duration on low burn 6 -10 hours 8 - 12 hours

Weight with packaging 335 lb (151.95 Kg) 390 lb (176.90 Kg)

E.P.A. Emissions

Surround Panels

Standard (width x height) 46” x 28.25” (1166 mm x 711 mm)

Oversized (width x height) 47.5” x 33” (1207 mm x 838 mm)

Rating Label Location Side of Unit; Behind Right Shroud

11,479 to 34,196 BTU/hour

(3,361 to 10,013 watt)

3.3 grams/hour

(0.116 oz/hour)

9,425 to 31,780 BTU/hour

(2,760 to 9,306 watt)

4.48 grams/hour (0.158 oz/hour)

Specifications

Adjacent wall

CLEARANCES TO COMBUSTIBLES - 1200 KI INSERT:

Table 2: 1200 KI Insert Clearance to Combustibles.

A Minimum clearance to an unshielded side wall 10” (254 mm) B Minimum clearance to an unshielded 8” (203

mm) mantel

C Minimum top facing (protruding ¾” [19 mm])

clearance

D Minimum side facing (protruding ¾” [19 mm])

clearance

E † From front of door opening to edge of ! oor

protection

F † From side/back of unit to edge of ! oor

protection

† FLOOR PROTECTION: If unit is raised 0” - 2” (0mm-51mm); 1” (25mm) non-combustible material with k value = 0.84 or equivalent. If unit is raised 2” - 8” (51mm-203mm); ½” (13mm) non-combustible material with k value = 0.84 or equivalent. If unit is raised greater than 8” (203 mm) or more; any non-combustible material can be used.

Table 3: Reduction in (B) Minimum Clearance from 1200 KI to 8” (203 mm) Mantel.

Type of protection Modiﬁ ed Clearance

A minimum of .013” (0.33mm) sheet metal spaced out 1” (25mm) by noncombustible spacers.

Ceramic tiles, or equivalent non-combustible material on non-combustible supports and spaced out 1” (25mm) by non-combustible spacers.

Ceramic tiles, or equivalent non-combustible material on non-combustible supports with a minimum of .013” (0.33mm) sheet metal spaced out 1” (25mm) by non-combustible spacers.

NOTES:

(1) Mantel protection must have at least 3” (75mm) edge clearance on all sides, except as provided in Note 4. (2) If an adhesive is used to support non-combustible material, it shall not lose adhesive qualities at temperatures likely to be encountered and shall not contribute a signi" cant combustible load. (3) Heat shield mounting hardware attached to combustible materials must be placed at the lateral extremities of the shield.

(4) Minimum clearance to unprotected walls and ceilings must be maintained.

21” (533 mm)

17½” (445 mm)

1” (25 mm)

USA 16” (406 mm)

CND 18” (450 mm)

USA 6” (152 mm)

CND 8” (200 mm)

10½” (267 mm)

14” (357 mm)

10½” (267 mm)

Minimum Depth 13½” (343 mm) 14” (279 mm)

Minimum Width at back of " replace 22#” (568 mm) 23” (584 mm)

Minimum Width at front of " replace 27” (686 mm) 27¼” (692 mm)

Minimum Width at front of " replace to include shroud 36” (915 mm) 36” (915 mm)

Minimum Height

** If the masonry lintel height is only 19¼” (489 mm) to 19¾” (502 mm) refer to INSTALLATION - MODIFICATIONS FOR INSTALLATION WITH 19¼” (489 MM) HIGH LINTEL - INSERT

Table 4: 1200 KI Insert Minimum Fireplace Size.

Masonry Zero Clearance

19¼” (489 mm)** or 19¾” (502 mm)

20” (508 mm)

Specifications

Adjacent wall

CLEARANCES TO COMBUSTIBLES - 1700 KI INSERT:

Table 5: 1700 KI Insert Clearance to Combustibles.

A Minimum clearance to an unshielded side wall 10” (254 mm) B Minimum clearance to an unshielded 8” (203

mm) mantel

C Minimum top facing (protruding ¾” [19

mm]) clearance

D Minimum side facing (protruding ¾” [19

mm]) clearance

E † From front of door opening to edge of ! oor

protection

F † From side/back of unit to edge of ! oor

protection

Table 6: Reduction in (B) Minimum Clearance from 1700 KI to 8” (203 mm) Mantel.

Type of protection Modiﬁ ed Clearance

A minimum of .013” (0.33mm) sheet metal spaced out 1” (25mm) by noncombustible spacers.

Ceramic tiles, or eqivalent non-combustible material on non-combustible supports and spaced out 1” (25mm) by non-combustible spacers.

Ceramic tiles, or eqivalent non-combustible material on non-combustible supports with a minimum of .013” (0.33mm) sheet metal spaced out 1” (25mm) by non-combustible spacers.

NOTES:

(1) Mantel protection must have at least 3” (75mm) edge clearance on all sides, except as provided in Note 4. (2) If an adhesive is used to support non-combustible material, it shall not lose adhesive qualities at temperatures likely to be encountered and shall not contribute a signi# cant combustible load. (3) Heat shield mounting hardware attached to combustible materials must be placed at the lateral extremities of the shield.

(4) Minimum clearance to unprotected walls and ceilings must be maintained.

24” (610 mm)

19½” (495 mm)

1” (25 mm)

USA 16” (406 mm)

CND 18” (450 mm)

USA 6” (152 mm)

CND 8” (200 mm)

12” (305 mm)

16"” (408 mm)

12” (305 mm)

Table 7: 1700 KI Insert Minimum Fireplace Size.

Minimum Depth 18” (457 mm) 18½” (470 mm)

Minimum Width at back of # replace 22$” (568 mm) 23” (584 mm)

Minimum Width at front of # replace 27” (686 mm) 27¼” (692 mm)

Minimum Width at front of # replace to include shroud 36” (915 mm) 36” (915 mm)

Minimum Height

** If the masonry lintel height is only 19¼” (489 mm) to 19¾” (502 mm) refer to INSTALLATION - MODIFICATIONS FOR INSTALLATION WITH 19¼” (489 MM) HIGH LINTEL - INSERT

Masonry Zero Clearance

19¼” (489 mm)** or 19¾” (502 mm)

20” (508 mm)

IMENSIONS - 1200 KI INSERT:

715

46"

1166

850

20"

508

472

22"

561

27"

687

36"

916

336

573

514

493

[483]

19"

497

529

128

400

Specifications

Figure 4: 1200 KI Insert Dimensions.

IMENSIONS - 1700 KI INSERT:

715

20"

508

472

850

46"

1166

526

[483]

19"

497

450

27"

686

515

126

36"

916

22"

561

27"

687

Specifications

Figure 5: 1700 KI Insert Dimensions.

Installation

Insert Cabinet Top

Air Deflector

EMOVAL FROM PALLET:

• Remove the bricks from the unit before starting.

• Remove the two (2) lag bolts (shown in Figure 6) that secure the unit to the pallet from inside the

• rebox.

Note: Before the bricks are re-installed, rivets (Figure 7)

must be placed in the two holes where the lag bolts were removed in the • rebox . This is done to make unit burn more ef• ciently.

Figure 7: Rivet.

Figure 6: Bolts to remove.

MODIFICATIONS FOR INSTALLATION WITH 19” (484MM) HIGH LINTEL:

The KI has a factory height of 19½” (496mm) and it can be

reduced to 19” (483mm) by modifying the cabinet

top and mounting position

Insert Unit:

1. Remove the thirteen T-20 screws holding the cabinet top in place (refer to Figure 8).

2. Remove the cabinet top and ! ip it onto its top.

3. Remove the Air De! ector (shown in Figure 9) by removing the two (2) T-20 screws.

4. Re-install the cabinet top onto the unit. The screw holes along the top of the unit should now line up with the top set of holes on the cabinet top.

Figure 8: Removing Cabinet Top from Unit.

Figure 9: Removing Air De! ector onto Cabinet Top.

Installation

Floor

Protection

Combustible Floor

Masonry Fireplace

(203 mm)

Rain Cap

Steel Plate or Flashing

Flexible or Rigid 6"

Stainless Steel Liner

Mantel

Top Facing

Damper Removed or Fastened Open

Sheet Metal Screws

Fastening Collar to

Stainless Steel Liner

Surround Panel

USA 16” (406 mm)

CND 18” (450 mm)

MASONRY FIREPLACE INSTALLATION:

Installation must be completed by a certiﬁ ed professional in order for warranty to

be valid.

Install only in a masonry • replace with a good-condition chimney at least 15 ft (4.6 m) high, both of which have been constructed in accordance with the building code. Refer to Tables 4 and 7 for minimum masonry • replace dimensions. Be sure the • replace and chimney are clean and sound without any cracks or loose mortar. Do not remove any bricks or mortar from the • replace.

If there is a combustible ! oor in front of the

masonry • replace, the • replace insert must be 8” (203 mm) above the combustible ! oor, and ! oor protection must be provided 18” (457 mm) in front of the • replace insert and 8” (203 mm) to each side of the unit. Refer also to SPECIFICATIONS - CLEARANCES TO COMBUSTIBLES - 1200 KI INSERT and SPECIFICATIONS

- CLEARANCES TO COMBUSTIBLES - 1700 KI INSERT.

Figure 10: Insert Installation into existing ﬁ replace with

hearth.

1. Remove any • replace damper or fasten

in a permanent open position.

2. (IN CANADA) The stove is vented with a 6” stainless steel liner that goes directly to the top of the chimney and is covered with a rain cap. The chimney top is sealed with a ! ashing or steel plate that supports the weight of the chimney liner. The installation must conform to the liner’s manufacturer’s instructions.

This • replace must be installed with a continuous liner of 6” diameter (CANADA ONLY) extending from the • replace insert to the top of the chimney. The chimney liner must conform to the class 3 requirements of ULC-S635 Standard for Lining Systems for Existing Masonry or Factory-Built Chimneys and Vents, or ULC-S640 Standard for Lining Systems for New Masonry Chimneys.

(IN U.S.A.)The appliance when installed, must follow local building codes, in the absence of local building codes, with the current NFPA 211 Standard for Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances.

Combustible Floor

Masonry Fireplace

USA 16” (406 mm) CND 18” (450 mm)

1" (25mm)

Non-Combustible Board (K 0.84)

Installation

Floor Protection

Combustible Floor

Masonry Fireplace

(203 mm)

USA 16” (406 mm)

CND 18” (450 mm)

Firebox Top

Cut-away

Vent pipe

Removable

Flue Collar

Collar Puller

Gasket

Flue Collar Clamp

Washer

Nut

Figure 11: Insert Installation into existing " replace without

hearth.

The •

ue collar is removable for installations

into • replaces with low openings.

a) Remove the rear two (2) secondary

air tube and C-Cast Ceramic Baf• es, if installed (see C-CAST CERAMIC BAFFLE INSTALLATION). Remove the secondary air

by placing a screwdriver (any style

tubes except • at head) into one of the air holes and tapping it with a hammer/mallet to the left.

b) Unscrew the two (2) nuts on top of the

inside of the • rebox, using a 9/16” wrench or socket (see Figure 13). The Flue Collar Clamps will slide off the bolts.

c) Pull the removable • ue collar off the top

of the unit.

d) Attach the • ue collar to the venting pipe

using sheet metal screws.

e) Push the unit into place while trying to

keep the collar attached to venting close to the opening on the top of the unit.

Figure 12: Insert Installation into existing ! oor level

masonry " replace.

f) Place the Collar Puller, over the two bolts of the Flue

Collar and pull it into place (see Figure 14). Ensure that the bolts are to the left and right of the hole. If they are not, the front secondary air tube will need to be removed in order to install or remove the C-Cast Ceramic Baf• es.

g) Slide the Flue Collar Clamps and washers over the bolts,

and screw the nuts back onto the bolts.

h) Re-install C-Cast Ceramic Baf• es and the rear two

(2) secondary air tube (see C-CAST CERAMIC BAFFLE INSTALLATION).

There are four (4) leveling legs (shown in Figure 15), two

(2) on each side, one at the back and one at the front of the unit. Adjust the legs using a ⅜” wrench to ensure the unit is

stable.

Figure 13: Attaching removable ! ue collar.

Installation

Masonry Fireplace

Mantel

Damper Removed or Fastened Open

Surround Panel

USA 16” (406 mm)

CND 18” (450 mm)

Insulation Around the

Back of the Face Plate

NOTE: To use this type of installation we recommend your chimney have a minimum cross-sectional area of 28 and a maximum of 144 square inch. If it is not within this range your chimney may not have sufficient draw for the fireplace to operate correctly. The required cross-section may vary depending on climate and if the chimney is inside (better) or outside.

Figure 14: Removable ﬂ ue collar in place.

4. Screw or nail the provided metal plate with the

wording “THIS FIREPLACE HAS BEEN ALTERED TO ACCOMMODATE A FIREPLACE INSERT AND SHOULD BE INSPECTED BY A QUALIFIED PERSON PRIOR TO THE RE-USE AS A CONVENTIONAL FIREPLACE.” to the inside of the ! replace.

SURROUND PANEL SEALED INSTALLATION FOR USA ONLY:

Figure 15: Leveling legs.

Note: Though this is an allowable installation, we do not recommend it because of the possibility of poor

draft, and therefore poor stove performance.

Before starting this type of installation refer to INSTALLATION - MASONRY FIREPLACE INSTALLATION

- INSERT for additional information. For ances refer to S

clear

O COMBUSTIBLES - 1200 KI INSERT and

T SPECIFICATIONS - CLEARANCES TO COMBUSTIBLES 1700 KI INSERT.

Before the face plate is installed onto

the unit, glue a 6” (150mm) wide R20 ! berglass insulation strip around the perimeter of the back of the panels using RTV silicon or stove gasket cement. When the face plate is installed onto the unit the insulation must overlaps the ! replace opening to form a seal between

PECIFICATIONS - CLEARANCES

the masonry ! replace and the unit’s face plate. Let the silicon or cement dry.

2. To make the installation of the surround

panel onto the unit easy have the unit 6” (150mm) out from the ! replace,

3. Push the insert into the ! replace, allowing

the insulation to form a seal between the panels and the ! replace. Tuck any exposed insulation behind the face plate.

Figure 16: Installation with Surround Sealed.

Installation

Front of fireplace opening.

INSTALLATION USING A BLOCK-OFF PLATE FOR USA ONLY:

If this unit is to be installed into a masonry ! replace or a zero-clearance ! replace with a direct connection you must install a non-combustible seal-off device such as a block-off plate or damper adapter. By installing a block-off plate you seal the chimney, ensuring that no smoke enters the home and sealing the chimney to encourage draft. To construct a block-off plate follow the below steps.

1. Determine where the block-off plate will be installed; above the top of the ! rebox (it must be high enough to easily install the connection pipe) but below the damper area. Look for a location that is level and in an area where the plate can be mounted easily.

The measurement that will be needed are as followed (refer

to Figure 17 and 18):`

A - The width at the front of the ! rebox at the height where

the block-off plate will be installed.

B - The width at the back of the ! rebox at the height where

the block-off plate will be installed.

C - Then depth of the block-off needed (the distance

between A and B).

D - The distance of the center of the " ue to the front of the

! replace opening. Refer to Step 3.

NOTE: In general masonry ! replaces have square ! reboxes

while zero-clearance (metal) ! replaces have domed ! rebox tops. Therefore zero-clearance block-off plates may be more dif! cult to install. Insulation may be used around the edges to simplify sealing the plate.

2. Create a cardboard template of the dimensions with 2” (51 cm) wide " anges on each side. These " anges will be used to mount the block-off plate to the inside of the ! rebox. Bend the " anges downwards on the template and place it inside the ! replace. Continue on if the template ! ts correctly in its planned location. If the template does not ! t, make a new template with the required corrections until it does ! t correctly.

3. With the template in place, mark the location for the center of the " ue pipe when the unit is in place. If installing a 1200 KI the distance will be approximately 8¼” or 9 15/16”

from the ! replace opening. If installing a 1700 KI the

back distance will be approximately 12¾” or 14 7/16” back from the ! replace opening. Remove the template and cut a 6¼” diameter hole centered on this mark.

Figure 17: 3D of Dimensions needed from

the Fireplace.

4. Using the template make the block-off plate of 24 gauge or thicker steel. Drill two (2) holes in each " ange for mounting the plate.

Figure 18: Layout of the Block-Off Plate.

5. Mount the block-off plate

Masonry Fireplace

Mantel

Damper removed

or fastened open

Surround Panel

USA 16” (406 mm)

CND 18” (450 mm)

Block-off plate or damper adaptor.

The stainless steel chimney connector must extend 12" (305mm) past the block-off plate.

Mantel

Surround Panel

USA 16” (406 mm)

CND 18” (450 mm)

Block-off plate or damper adaptor.

Stainless steel chimney connector must extend 12" (305mm) past the block-off plate.

Damper must be removed

Zero-clearance (metal) firebox

IMPORTANT: DO NOT modify

any part of the ZC fireplace

using masonry screws in a masonry • replace and sheet metal screws on a zeroclearance • replace (screws need only be long enough to penetrate the • rst layer of metal).

6. Insulate the block-off plate using high - temperature

• berglass insulation and furnace cement.

Installation

Figure 20: Masonry Fireplace Direct Connection Insert Install.

Figure 19: Insert Install into a Zero-Clearance Fireplace.

7. After installing the unit into place and the pipe through the block-off plate, use high - temperature • berglass insulation and furnace cement to seal any gaps between the pipe and blockoff plate (allow the cement to dry for at least 24 hours before burning).

Before starting this type of installation refer to I

NSTALLATION - INSERT for additional

ormation. For clearances refer to

inf

NSTALLATION - MASONRY FIREPLACE

SPECIFICATIONS - CLEARANCES TO COMBUSTIBLES

- 1200 KI INSERT and SPECIFICATIONS -

CLEARANCES TO COMBUSTIBLES - 1700 KI INSERT. See Figure 19 and 20 for examples of a masonry • replace and a zero-clearance

• replace with a direct connection

Installation

Tube A

Tube E

Tube D

ODEL 1200 KI BRICK PLACEMENT & TUBE LOCATIONS:

COMPLETE THE STOVE AND SMOKE PIPE INSTALLATION BEFORE PLACING THESE BRICKS.

1. Place the three (3) full size bricks along each side of the

ﬁ rebox and one (1) full size brick on either side of the back of the ﬁ rebox.

2. To place the ! oor bricks, lay the two (2) partial bricks along the back of the ! oor. Then on the left, lay two (2) full size bricks and on the right, lay a full size brick in the center and the half brick in the front (for the ash dump). The spaces between the bricks will soon

ﬁ ll with ashes.

Figure 21: Brick Placement for 1200 KI shown with Secondary Air

When replacing bricks, use only pumice type ﬁ re bricks.

Channel and Tubes.

TOTAL BRICKS:

12 - Full size bricks 9” long x 4.5” wide x 1.25” thick (22.9 cm long x 11.4 cm wide x 3.2 cm thick)

2 - Partial bricks 9” long x 3” wide x 1.25” thick (22.9 cm long x 7.6 cm wide 3.2 cm thick)

Removing Air Tube: If a secondary air tube needs to be removed, place a screwdriver (any style except

! at head) into one of the air holes and tap it with a hammer/mallet to the left until the right end of the tube is freed. To installation a secondary air tube reverse the above instructions.

IMPORTANT: All secondary air tubes must be in place for proper operation.

Installation

Tube A

Tube C

Tube B

ODEL 1700 KI BRICK PLACEMENT & TUBE LOCATIONS:

COMPLETE THE STOVE AND SMOKE PIPE INSTALLATION BEFORE PLACING THESE BRICKS.

1. Place the four (4) full size bricks along each side of the ﬁ rebox and one (1) full

size brick on either side of the back of the ﬁ rebox.

2. To place the ! oor bricks, lay the two (2) partial bricks along the back of the ! oor. Then on the left, lay three (3) full size bricks and on the right, lay two (2) full size bricks in the center and the half brick in the front (for the ash dump). The spaces between the bricks

will soon ﬁ ll with ashes.

Figure 22: Brick Placement for 1700 KI shown with Secondary Air Channel

and Tubes.

When replacing bricks, use only pumice type ﬁ re bricks. TOTAL BRICKS:

16 - Full size bricks 9” long x 4.5” wide x 1.25” thick (22.9 cm long x 11.4 cm wide x 3.2 cm thick)

2 - Partial bricks 9” long x 3” wide x 1.25” thick (22.9 cm long x 7.6 cm wide 3.2 cm thick)

Removing Air Tube: If a secondary air tube needs to be removed, place a screwdriver (any style except

! at head) into one of the air holes and tap it with a hammer/mallet to the left until the right end of the tube is freed. To installation a secondary air tube reverse the above instructions.

IMPORTANT: All secondary air tubes must be in place for proper operation.

Left Ceramic Baffle

Right Ceramic Baffle

Installation

C-CAST CERAMIC BAFFLE INSTALLATION:

1. Slide the right C-Cast Ceramic Baf! e in over the secondary air tubes at the top of the " rebox. The tab

must be on the top and pointing towards the center and the smooth side is to face down.

2. Hook the outside edge of the baf! e over the top of the secondary air chamber. This will make room to for the installation of the left C-Cast Ceramic Baf! e.

3. Slide the left C-Cast Ceramic Baf! e in over the secondary air tubes. The tab must be on the bottom and pointing towards the center and the smooth side is to face down.

4. Pull the baf! es together in the middle so the right tab rests on top of the left tab. Ensure the baf! es are ! ush with the back and both sides of the " rebox.

Note: If the bolts on the ! ue collar are not to the left and right of the hole, the front secondary air tube will need to be removed in order to install or remove the C-Cast Ceramic Baf! es. To remove the front secondary air tube place a screwdriver (any style except ! at head) into one of the air holes and tapping it with a hammer/mallet to the left.

Figure 23: Installation of C-Cast Ceramic Baf! e.

FAN WIRING DIAGRAMS:

This appliance, when installed, must be electrically connected and grounded in accordance with local codes or in the absence of local codes, with the current CSA C22.1 CANADIAN ELECTRICAL CODE. Part 1, SAFETY STANDARDS FOR ELECTRICAL INSTALLATIONS, or THE NATIONAL ELECTRICAL CODE ANSI / NFPA 70 in the USA.

CAUTION Label all wires prior to disconnection when servicing controls. Wiring errors

can cause improper and dangerous operation. Verify proper operation after servicing.

DO NOT oil the fan bearings. DO NOT cut or remove the grounding prong from the plug. DO NOT route the power cord beneath the heater or away from the heat.

WARNING: This appliance is equipped with a three-prong (grounding) plug for your protection against

shock hazard and should be plugged into a properly grounded three-prong receptacle.

Fan

White

Black

Fan Temp Sensor

Fan Controller (Rheostat)

Power Supply

Ground

Rocker Switch

WIRE B (Black) - 12”

WIRE A (Black) - 26”

WIRE C (Black) - 14” + 14”

AUTO

OFF

MANUAL

Installation

FAN REMOVAL:

The KI Insert comes with the fan assembled and installed in the left shroud.

1) Remove fan shourd, there are two 8-32 T-20 screws mounting it to the ! rebox, there are two ½” hole in the cabinet side to access screws.

2) Disconnect all electrical connections to the fan.

3) Remove the four 8-32 X ¾” hex head screws that hold the fan mounting plate to the shroud.

4) Remove the fan control knob and nut from the front of the shroud and pull the controls out the back.

5) Install the fan kit into the new shroud by following reversing steps 1 to 3. Refer to F

WIRING DIAGRAM to ensure the fan is reconnected

operly.

Figure 24: KI Fan Wiring Diagram.

Figure 25: Left Fan Shroud Assembly

REMOVAL OF TOP:

Installation

1. To remove the top from the unit lift up and pull forward.

Figure 26: Removal of Top.

INSTALLATION OF THE SURROUND PANEL:

1. You will need to remove the top as shown above before installing the surround panel.

2. Once the top has been removed slide the surround panel over the unit.

3. The surround will hook on to the side shrouds.

4. Re-install the top once the surround is in place.

Figure 27: Installation of Surround Panel.

Rating Label

**Alcove (Use double wall pipe) / Alcôve (Utilisant le double connecteur de mur)

I Total width / Largeur totale 55” (1397 mm)

Model/Modèle 1200

J Total height / Hauteur totale 78” (1981 mm) K Top of stove to ceiling / Le sommet de poêle au plafond 49” (1245 mm) L Sidewall to unit / De la paroi latérale au dispositif

Sidewall to connector / De la paroi latérale au connecteur Backwall to unit / De la paroi arrière au dispositif Backwall to connector / De la paroi arrière au connecteur

15” (381 mm) M 24” (610 mm) N 12” (305 mm) O 15” (381 mm)

51” (1295 mm)

Model/Modèle 1700

72” (1829 mm) 44” (1118 mm)

13” (330 mm) 22” (559 mm)

8” (203 mm)

11” (279 mm)

Maximum Depth / Profondeur maximumP 48” (1220 mm) 48” (1220 mm)

Single wall pipe /

Seul connecteur de mur

**Double wall pipe /

Double connecteur de mur

Top vent out back wall with min. 24” (610mm)

vertical rise; double wall pipe / Donné vent hors

de la paroi arrière avec le min. 24” (610 mm)

l'ascension verticale; double connecteur de mur

13” (330 mm) 14” (356 mm)

11” (279 mm) 8” (203 mm) 12” (305 mm)

C 9” (229 mm) 6½" (165 mm)

22” (559 mm) 22” (559 mm) 23” (584 mm)

14” (356 mm) 11” (279 mm) 15” (381 mm)

11” (279 mm)

16” (381 mm) 15” (406 mm)

17½” (445 mm) 16½” (419 mm)

10” (254 mm)

8½" (216 mm)

22” (559 mm)

17” (432 mm) 15” (381 mm)

7” (178 mm)

6” (152 mm)

22” (559 mm) 10” (254 mm)

14½” (368 mm)

† Front of door opening to edge of hearth / Le devant d'ouverture de porte au bord de coussin de coeur

USA 16” (406 mm) CND 18” (450 mm)

USA 6” (152 mm) CND 8” (200 mm)

Sidewall to unit / De la paroi latérale au dispositif

Sidewall to connector / De la paroi latérale au connecteur

Backwall to unit / De la paroi arrière au dispositif

Backwall to connector / De la paroi arrière au connecteur

Adjacent wall to corner of unit / De la paroi adjacent au coin de dispositif

Adjacent wall to connector/ De la paroi adjacent au connecteur

1200

20” (508 mm) 12” (305 mm)

10" (254 mm)

29” (737 mm) 15” (381 mm)

18½” (470 mm)

1700

1200 1700 1200 1700 1200 1700

Double wall pipe with efficiency

shield (Flat top model only) / Double connecteur de mur avec la protection d'efficacité (Le modèle plat seulement

Model / Modèle

Minimum Clearances to Combustible Materials / Espaces Libres Aux Materiax Combustibles.

13” (330 mm) 13” (330 mm) 13” (330 mm) 13” (330 mm)

13” (330 mm)

13” (330 mm)13” (330 mm)

22” (559 mm)

10” (254 mm)

8” (203 mm)

† Side/back of unit to edge of hearth / Le latérale/arrière de dispositif au bord de coussin de coeur

Front / Mur avant

Floor Protection / Protection du sol

Back wall/ Mur arrière

Sid¸e wall / Mur a côté

Alcove Back wall / Mur d’alcôve a l’arrière

Alcove Side wall /

Mur d’alcôve a côté

Front /

Mur avant

Adjacent wall / Mur adjacent

Alcove / Alcôve

Front / Mur avant

Certified for use in Canada & USA /

Certifié pour installation au Canada et aux Etats-Unis.

Adjacent wall / Mur adjacent

CAUTION: An uninsulated smoke pipe must not pass through an attic, roof space, closet or similar concealed space, or through a floor, ceiling, wall, or partition, or any combustible construction. † FLOOR PROTECTION: If a stove is installed on a combustible floor, it must have the legs or pedestal attached and be on a NON COMBUSTIBLE hearth pad * ALL CLEARANCES CAN BE REDUCED WITH SHIELDING ACCEPTABLE TO THE LOCAL AUTHORITY. SINGLE WALL: IN CANADA: Any ULC-S629 listed chimney system with the accompanying listed single wall vent connector. IN U.S.A.: Any UL 103 HT listed chimney system with the accompanying listed single wall vent connector. **DOUBLE WALL : IN CANADA: Any ULC-S629 listed chimney system with the accompanying listed double wall vent connector. IN U.S.A.: Any UL 103 HT listed chimney system with the accompanying listed double wall vent connector. DOUBLEWALL IS REQUIRED FOR MOBILE HOME INSTALLATIONS.

† FLOOR PROTECTION / PROTÉGER LE PLANCHER: If unit is raised / Si l'appareil est soulevé: 0” - 2” (0mm - 51mm); 1” (25mm) non-combustible material with k value = 0.84 or equivalent /

1” (25mm) le matériel incombustible avec la valeur de k = 0.84 ou équivalent.

2” - 8” (51mm - 203mm); ½” (13mm) non-combustible material with k value = 0.84 or equivalent /

½” (13mm) le matériel incombustible avec la valeur de k = 0,84 ou équivalent.

Greater than/Plus grand que 8” (203 mm) any non-combustible material /

n'importe quel type de matériel incombustible.

DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE

LISTED SOLID FUEL SPACE HEATER / IDENTIFIE COMME UN FOYER A COMBUSTIBLE SOLIDE

Serial No. / No. De Serié:

Models 1200 and 1700 Freestanding units: Room Heater, Solid Fuel Type, Also For Use In Mobile Homes. Tested to ULC-S627-00, ULC-S628-93 (FPI only), & UL-1482-10.

Install and use only in accordance with the manufacturers installation and operating instructions. Contact local building or fire officials about restrictions and installation inspection in your area. Use 6” (150 mm) diameter minimum 24 MSG black or 25 MSG blued steel connector listed factory-built chimney suitable for use with solid fuels or masonry chimney. See local building code and manufacturer’s instructions for precautions required for passing a chimney through a combustible wall or ceiling. Do not pass chimney connector through a combustible wall or ceiling. Minimum clearances from horizontal connector and ceiling 18” (455 mm). Do not connect this unit to a chimney flue servicing another appliance.

Modèles 1200 et 1700 items indépendants: Chauffage pièce, le type de combustible solide, également pour une utilisation dans les maisons mobiles. Testé selon ULC-S627-00, ULC-S628-93 (FPI seulement), & UL-1482-10.

Ce dispositif doit entre installé et opéré conformément aux instructions d'installation et d'opération du manufacturier contactez le service local de l'inspection des bâtiments ou l'officier pompier concernant les restrictions et l'inspection d'installation dans votre localité. Utiliser des connecteurs répertoriés 24 MSG noir ou 25 MSG en acier bronzée de 6" (150 mm) minimum, et une cheminée de fabrication industrielle, appropriée pour utilisation avec des combustibles solides ou avec une cheminée de maçonnerie. Vérifiez les précautions a prendre exigées parle code local et les instructions du manufacturier concernant les conditions pour passer la cheminée a travers un mur ou un plafond combustible. Net pas installer le connecteur de la cheminée a travers un mur ou un plafond combustible. Espaces libres minimum d'un connecteur horizontal et plafond sont 18" (455 mm) ne pas connecter ce dispositif a un conduit de cheminée qui sert déjà un autre dispositif.

DATE OF MANUFACTURE /

DATE DE FABRICATION:

J F M A M J J A S O N D 2014 2015 2016 2017 2018

C-14290

MANUFACTURED BY /

FABRIQUE PAR

: SHERWOOD INDUSTRIES LTD. 6782 OLDFIELD ROAD, SAANICHTON, BC CANADA

MADE IN CANADA /

FABRIQUE AU CANADA

HOT WHILE IN OPERATION.

DO NOT TOUCH. KEEP CHILDREN,

CLOTHING AND FURNITURE AWAY. CONTACT MAY CAUSE

SKIN BURN. READ NAMEPLATE AND INSTRUCTIONS.

CAUTION:

TRÈS CHAUD QUAND ALLUMÉ. NE TOUCHEZ PAS. TENIR LOIS LES ENFANTS, LES VÊTEMENTS ET LES MEUBLES. LE CONTACT PEUT CAUSER DES BRÛLURES. LISEZ ATTENTIVEMENT L’ÉTIQUETTE ET LES INSTRUCTIONS.

MISE EN GARDE:

OPERATE ONLY WITH DOORS CLOSED. Only open door to feed fire. For use with solid wood fuels only. Do not use any other type of fuel. Do not use grate or elevate-fire build wood fire directly on hearth. Do not overfire. Do not obstruct beneath the heater. If heater or chimney connector glows, you are overfiring. Inspect and clean chimney frequently-under certain conditions of use, creosote buildup may occur rapidly. The provided insulation materials are required for operation. Keep furnishing and other combustibles well away from heater. Replace glass only with 5 mm thick ceramic glass. Optional component for FS: fan, electrical rating 115V, 60 Hz 1 Amp (Part # EFW-261). Combustion air openings are not to be obstructed. Danger: Risk of electrical shock. Disconnect power before servicing unit. Route cord away from heater.

Models 1200 and 1700 inserts may be installed as an insert in a masonry fireplace. / On peut encastrer le modèles 1200 et 1700 dans un foyer de maçonnerie.

L’OPERATION DU POELE DOIT SE FAIRE AVEC LA PORTE FERME. N'ouvrir la porte que pour alimenter le feu. N'utilisez que des combustibles solides. Ne pas utiliser un autre type de carburant. N'employez pas de grille de foyer ou ne surélevez pas le feu. Mettez le bois à brûler directement sur l'âtre. Pour éviter la surchauffeur, ne mettez pas trop de bois. N'obstruez pas les ouvertures d'air comburant. Si le poêle ou le connecteur commencent à luire, vous surchauffez le poêle. Inspectez et nettoyez la cheminée souvent. Dans certaines conditions, le créosoté peut s'accumuler rapidement. Les matériaux d'isolation fournis sont requis pour l'opération.Tenez loin les meubles et d'autres produits combustibles. Ne remplacez le verre qu'avec du verre céramique, 5mm

MISE EN GARDE: Un uninsulated tuyau de fumée ne doit pas passer par un grenier, un espace de toit, le placard ou l'espace dissimulé similaire, ou par un plancher, un plafond, un mur, ou une cloison, ou une construction combustible. † PROTÉGER LE PLANCHER: Si une cuisinière est installée sur un sol combustible, il doit avoir un piédestal attache et être sur un coussinet non- combustible. TOUS “ESPACES LIBRES AUX MATERIAX COMBUSTIBLES” PEUVENT ÊTRE RÉDUITS AVEC PROTÉGEANT ACCEPTABLE À L’AUTORITÉ LOCALE. Seul Connecteur de Mur: Au Canada: Certifiée seul connecteur de mur avec toute systèmes de

cheminée listée sous ULC-S629. Aux États-Unis: Certifiée seul connecteur de mur avec toute systèmes de cheminée listée sous UL 103 HT. **Double Connecteur de Mur: Au Canada: Certifiée double connecteur de mur avec toute systè

mes de cheminée listée sous ULC-S629.

Aux États-Unis: Certifiée double connecteur de mur avec toute systèmes de cheminée listée sous UL 103 HT.

DOUBLE CONNECTEUR DE MUR NÉCESSAIRES POUR INSTALLATION DANS LES MAISONS MOBILE.

Tested & Listed By

Model / Modèle 1200 FPI 1700 FPI

A To unshielded side wall / aux mur non protegé 10” (254 mm) 10” (254 mm)

B To an unshielded 8” (203 mm) mantle / aux manteau 8“ non protegé 21” (533 mm) 24” (610 mm) C To top facing (protruding ¾” [19 mm]) clearance / aux revêtement supérieur 17½” (445 mm) 19½” (495 mm) D To side facing (protruding ¾” [19 mm]) clearance / aux revêtement a côté 1” (25 mm) 1” (25 mm)

E † From door opening of unit to edge of floor protection /

De ouverture de la porte de l'unité à bord de la protection de plancher USA 16” (406mm) / CND 18” (450mm) F † From side of unit to edge of floor protection / Du côté de l'unité au bord de la protection de plancher USA 6” (152 mm) / CND 8” (200 mm)

épais. Équipement en option pour un FS: ventilateur caractéristiques assignées 115V, 60 Hz, 1 Amp (pièce # EFW-261) tenez le câble électrique loin du poêle. Danger: Le risque de choc électrique. Débrancher le dispositif avant d'entretenir. Ouvertures d'air de combustion ne doivent pas être obstrués.

Model /

Modèle:

Report/Rapport no.

Kodiak 1200 FS 268-S-04b-2

Venice 1200 FPI 268-S-05b-2

KI 1200 FPI 268-S-05b-2

Boston 1200 FPI 268-S-05b-2

Kodiak 1700 FS 268-S-01b-2

Venice 1700 FPI 268-S-06b-2

KI 1700 FPI 268-S-06b-2

Boston 1700 FPI 268-S-06b-2

Boston 1200 FS 268-S-04b-2

Boston 1700 FS 268-S-01b-2

ype de mat

riel incombustible.

Le risque de choc électrique. Débrancher le

(25mm) non-combustible material with k value = 0.84 or equivalent /

(25mm) le mat

½”

(13mm) non-combustible material with k value = 0.84 or equivalent /

½”

(13mm) le mat

(203 mm) any non-combustible material /

Floor Protection /

Front /

Mur avant

Back wall/

Mur arrière

Adjacent wall /

Mur adjacent

e double connecteur de mur avec toute syst

DOUBLE CONNECTEUR DE MUR N

MOBILE.

e double connecteur de mur avec toute syst

tre sur un coussinet non- combustible.

½”

MISE EN GARDE: Un uninsulated tuyau de fum

l'espace dissimul

†

PROTÉGER LE PLANCHER:

tre sur un coussinet non- combustible.

TOUS

ESPAC

ACCEPTABLE

Seul Connecteur de Mur:

Au Canada: Certifi

Aux

(330 mm)

(279 mm)

(229 mm)

Parts List

Reference # Description Part #

1 120F (49C) Ceramic Fan Temperature Sensor EC-001 2 Insert Burner Switch EC-026 3 FPI Fan Controller 115V EC-039 4 Domestic Power Cord 115V EC-042 5 Heyco Strain Relief EC-044 6 Wood Door Gasket EF-168 7 Glass with Tape 10-000 8 Enviro Logo Gel Decal 50-322

9 1200 & 1700 Front Secondary Air Tube A 50-1099 10 1700 Rear Secondary Air Tube C 50-1100 11 1700 Middle Secondary Air Tube B 50-1101 12 1200 Secondary Air Tube Rear E 50-1102 13 1200 Secondary Air Tube Middle D 50-1103 14 Pumice Brick 3” x 9” 50-1104 15 Pumice Brick 4.5” x 9” 50-1105 16 Glass Retainer Kit (With Screws) 50-1122 17 1200 & 1700 Left Shield Assembly 50-1144 18 1200 & 1700 Right Shield Assembly 50-1145 19 1200 Ceramic Bafﬂ e - L/R Set 50-1146

20 1700 Ceramic Bafﬂ e - L/R Set 50-1147 21 FPI Flue Collar Assembly 50-1148 22 FPI Angled Flue Collar Assembly 50-1565 23 1200 & 1700 Ceramic Flue Gasket 50-1413 24 1200 & 1700 Cast Latch 50-1381 25 1200 & 1700 Insert Replacement Fan 50-2204 26 1200/1700 KI Formed Surround Panel 50-2893 27 Fireplace Insert Base Shelf 50-1986 28 KI Formed Top 50-2911 29 KI Left Fan Shroud 50-2912 30 KI Right Shroud 50-2913

31 KI Left Fan Shroud Complete 50-2914 32 Wood Handle w/ Hardware 50-2909 33 Painted Cast Door Complete 50-2897 34 Trimmable Oversize Panel 50-2896 35 1200/1700 KI OS Surround Panel 50-3015

KI Owners Manual 50-2910

Parts Diagram

Jan 2013

Sher wood Industries Ltd. (“Sherwood”) hereby warrant

s, subject to the terms and conditions herein set for th, this product against defects in material and workmanship during the specified warranty period starting from the date of original purchase at retail. In the event of a defect of material or workmanship during the specified warranty period, Sherwood reserves the right to make repairs or to assess the replacement of a defective product at Sherwood’s factory. The shipping costs are to be paid by the consumer. All warranties by Sherwood are set forth herein and no claim shall be made against Sherwood on any oral warranty or representation.

Conditions

 A completed warranty registration must be submitted to Sherwood within 90 days

of original purchase via the online warranty registration page or via the mail-in warranty registration card provided. Have the installer fill in the installation data sheet in the back of the manual for warranty and future reference.

 This warranty applies only to the original owner in the original location from date of

install.

 The unit must have been properly installed by a qualified technician or installer, and

must meet all local and national building code requirements.

 The warranty does not cover removal and re-installation costs.

 Sherwood Industries Ltd. reserves the right to make changes without notice.

 Sherwood Industries Ltd. and its employees or representatives will not assume

any damages, either directly or indirectly caused by improper usage, operation, installation, servicing or maintenance of this appliance.

 A proof of original purchase must be provided by you or the dealer including serial

number.

Exclusions

An expanded list of exclusions is available at www.enviro.com/help/warranty.html

This warranty does not cover:

 Damage as a result of improper usage or abuse.

 Damage caused from over-firing due to incorrect setup or tampering.

 Damage caused by incorrect installation.

To the Dealer

 Provide name, address and telephone number of purchaser and date of purchase.

 Provide date of purchase. Name of installer and dealer. Serial number of the

appliance. Nature of complaint, defects or malfunction, description and part # of any parts replaced.

 Pictures or return of damaged or defective product may be required.

To the Distributor

 Sign and verify that work and information are correct.

Sherwood Industries Ltd.

6782 Oldfield Road, Victoria, BC . Canada V8M 2A3

Online warranty registration: www.enviro.com/warranty/

Warranty for Enviro Wood Products

Category One Year Two Year Limited Lifetime (7yr)

Parts

(unit s erial n umber required)



Firebox

(excluding bri cks)



Ceramic Baffle



Secondary Air Tubes



Surround Panels

(excluding fin ish)



Pedestals / Legs

(excluding fin ish)



Ceramic Glass



Door Assembly

(excluding gas ket)



Slider Control



Shield Assembly



Electrical Components



Convection Fan



Exterior Surface Finishing



Gasket



Labour



Whereas warranty has expired, replacement parts will be warrantied for 90 days from par t purchase date. Labour not included.

Unit serial number required.

Warranty does not cover damage caused from burning artificial/firest

arter log varieties.

Excludes damage caused by loading wood, cleaning or service.

Glass is covered for thermal breakage. Photos of box, inside of door, and unit s

erial # must be supplied for breakage due to shipping.

Exterior Surface finishing covers Plating, Enamel or Paint and exclude

s colour changes, chipping, and fingerprints.

Travel costs not included.

No warranty on replacement firebricks

Installation Data Sheet

The following information must be recorded by the installer for warranty purposes and future reference.

NAME OF OWNER:

_________________________________________

ADDRESS:

_________________________________________

PHONE:___________________________________

MODEL:___________________________________

SERIAL NUMBER:___________________________

DATE OF PURCHASE: ______________(dd/mm/yyyy)

NAME OF DEALER:

_________________________________________

ADDRESS:

_________________________________________

PHONE:___________________________________

NAME OF INSTALLER:

_________________________________________

DATE OF INSTALLATION:___________(dd/mm/yyyy)

INSTALLER’S SIGNATURE:

_________________________________________

MANUFACTURED BY:

SHERWOOD INDUSTRIES LTD.

6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3

www.enviro.com

Jan. 14th 2014

ADDRESS:

_________________________________________

PHONE:___________________________________

C-14287

Enviro 1200 KI FPI, 1700 KI FPI Installation And Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual