Entryvue VD-950 Instruction Manual

Door Station A Door Station B Door Station C Door Station F Door Station G

The design and specications of this manual can be changed without notication
to the user. All copyrights and interpretation rights are reserved to Evervue.

1

2

ON

DPS

Basic instructions:

1. Check the contents of your order. To be able to set up a system,
you must have at least the following:

*One Door station
*One Monitor
*DPS Box (Power distributor Box)
*Power Supply (PS-50 or PS-55)

2. Recommended wires are:

*14 gauge 2 conductor stranded wire.
*CAT5 (MUST use a pair of wire for
each conductor)
Strip the ends of the wires about 1/3”. If using stranded wires or CAT5,
solder the ends to ensure a good connection. Do Not use wire nuts to
connect wires(wire nuts are for power and solids wires).

3. If multiple door stations and monitors are used, you can con nect
them in series (daisy chain) or in parallel.

4. Connect the wire to the BUS connection
on the Door Station ( 2 connections on the
left ). Then connect the other end of that
same wire to the left connectionon the DPS
box.

4.1 Connect the wire to the right side of
the DPS Box. Then connect the other
end of that same wire to the green plug
and then to the back of the monitor.
Make sure that these wires do not twist
too much, and that they are well isolated
from each other.

5. Door Strike/Magnetic lock

5.1 Door Lock controlled by Dry Contact:
If you have a large system, it is not recommended to have the Door
Station providing the power for the lock, so use a separate power
supply for the door lock.

The unlock setting on monitor:
8010 - lock mode to 0 - Normally open
8011 - lock mode to 1 - Normally closed

*Use Exit Bottom with magnetic lock only.

good

wrong

well twisted and soldered

Connect one lock

lock lock 1

lock 2

Remove jumper

Connect two locks

Remove jumper

*Exit Button
( Magnetic lock only )

*Exit Button
( Magnetic lock only )

Page 01

4.2. Connect the Red Wire of
the DPS Box to the Positive
(24V) of the power supply,
usually the
V+ or the Red connection. The
black wire should connect to the
V- or the black connection of
the power supply.

4.3. Plug in the power supply. Connect the terminal L and N to 110 ­240V input. This can be hardwired, or you can connect a cable w ith a
plug. If you have a PS-55, make sure that the voltage switch in the unit
is set to 110V or 220V before turning ON (depending the country you
live).

5.2 Door Lock controlled with Internal Power - Door strike:

Recommended only for 1 Door Station + 1 Monitor

-The door lock is limited to 12V, 250mA

-The Unlock Setting of monitor must be set to 0 (by default).

6. Ensure to set the Dip Switches of the Door Stations and Monitors
correctly. Refer to the next page.

7. Unlock Setting (set in monitor)

-You must connect the system correctly before programming the unlock
setting.

-It will be saved automatically, so you only need to set in one monitor.

1. Press the “EntryVue” logo located on the bottom left of the screen.

2. Press the screen for 3 seconds,then select “Installer’s Menu .”

3. Then enter one of the following codes:
8021# : 1 second
8022# : 2 seconds
8023# : 3 seconds
8024# : 4 seconds
8025# : 5 seconds
8026# : 6 seconds
8027# : 7 seconds
8028# : 8 seconds
8029# : 9 seconds

8.Innercall Feature;

There are 2 ways to set up the intercom function, and you need to decide
which one you want during the set up.

1. You can call a specic monitor. This is the standard defau lt.

2. You can innercall up to 4 monitors. In this case, you need t o set all 4
monitors with the same dip switches and one of them needs to be set as
“master”. The other 3 must be set as “slave” in the “Installer’ s Menu”
(Press the “EntryVue” logo located on the bottom left of the sc reen).

Jumper position in 1-2

Lock

9. Showing video on multiple monitors:

You can have up to 3 or 4 monitors (depending on the distance) showing
video when the door bell is pressed. Default setting is to one monitor
showing video.
On the monitor that you want to show video, press the “EntryVue” Logo,
then press the screen for 3 seconds, and then enter the code 8006#.

10. Maximum distance:

Wire used

CAT5 or CAT6

18/2 speake wire
(stranded,not
shielded)

14/2 speake wire
(stranded,not
shielded)

Maximum distance
between door station
and monitor

Use 1 pair for each
conductor. Solder
the ends of the
pair together

Solder connections
together. Set voltage
between 25-27 volt
(can be adjusted on
the power supply)

300 feet (100 meters)

Comment

300 feet (100 meters)

500 feet (150 meters)

Page 02