Entrematic OBBI3BH, OBBI3BFCH Original Instruction

Ditec OBBI

Swing gates automation

(Original instruction)

www.ditecentrematic.com

IP1639EN

Technical manual

24

IP1639EN - 2015-05-13

25

IP1639EN - 2015-05-13

Index

Caption

Subject Page

1. General safety precautions 26

2. Declaration of incorporation of partly completed machinery 27

2.1 Machinery Directive 27

3. Technical specifications 28

3.1 Operating instructions 28

4. Standard installation 29

5. Geared motor references 30

6. Installation 31

6.1 Preliminary checks 31

6.2 Geared motor installation 31

7. Electrical connections 35

7.1 OBBI3BFCH limit switch adjustment 36

8. Ordinary maintenance program 37

User instructions 39

i

This symbol indicates instructions or notes regarding safety, to which special atten­tion must be paid.

This symbol indicates useful information for the correct functioning of the product.

26

IP1639EN - 2015-05-13

1. General safety precautions

This installation manual is intended for qualified personnel only.

Installation, electrical connections and adjustments must be performed in ac­cordance with Good Working Methods and in compliance with the present standards.
Read the instructions carefully before installing the product.
Bad installation could be dangerous.

The packaging materials (plastic, polystyrene, etc.) should not be discarded in

the environment or left within reach of children, as these are a potential source
of danger.
Before installing the product, make sure it is in perfect condition.
Do not install the product in explosive areas and atmospheres: the presence of inflam­mable gas or fumes represents a serious safety hazard.
Before installing the motorisation device, make all the necessary structural modi­fications in order to create safety clearance and to guard or isolate all the crushing,
shearing, trapping and general hazardous areas.
Make sure the existing structure is up to standard in terms of strength and stability.
The motorisation device manufacturer is not responsible for failure to observe Good
Working Methods when building the frames to be motorised or for any deformation
during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed
taking into account: applicable laws and directives, Good Working Methods, installa­tion premises, system operating logic and the forces developed by the motorised door.

The safety devices must protect the crushing, cutting, trapping and general

hazardous areas of the motorised door.
Display the signs required by law to identify hazardous areas.
Each installation must bear a visible indication of the data identifying the motorised
door.
When requested, connect the motorised door to an effective earthing system that
complies with current safety standards.
During installation, maintenance and repair operations, cut off the power supply before
opening the cover to access the electrical parts.
The automation protection casing must be removed by qualified personnel only.

The electronic parts must be handled using earthed antistatic conductive arms.

The manufacturer of the motorisation declines all responsibility in the event
of component parts being fitted that are not compatible with the safe and correct
operation.
Use original spare parts only for repairs or replacements of products.
The installer must supply all information on automatic, manual and emergency opera­tion of the motorised door and must provide the user with the operating instructions.

27

IP1639EN - 2015-05-13

2. Declaration of incorporation of partly
completed machinery

2.1 Machinery Directive

(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB with headquarters in Lodjursgatan 10, SE-261 44 Land­skrona, Sweden, declares that the automation for Ditec OBBI type swing gate:

- has been constructed to be installed on a manual door to construct a machine pursuant to the

Directive 2006/42/EC. The manufacturer of the motorised door shall declare conformity pursu­ant to the Directive 2006/42/EC (Annex II-A), prior to the machine being put into service;

- conforms to the applicable essential safety requirements indicated in ANNEX I, Chapter 1 of the

Directive 2006/42/EC;

- conforms to the Low Voltage Directive 2006/95/EC;

- conforms to the Electromagnetic Compatibility Directive 2004/108/EC:

- the technical documentation conforms to Annex VII-B of the Directive 2006/42/EC;

- the technical documentation is managed by Marco Pietro Zini with headquarters in Via Mons.

Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY;

- a copy of technical documentation will be provided to national competent authorities, following

a suitably justified request.

Lan dskr ona, 06-05-2013 Marco Pietro Zini
(President)

Pursuant to Machinery Directive (2006/42/EC) the installer who motorises a door or gate has the
same obligations as the manufacturer of machinery and as such must:

- prepare the technical file which must contain the documents indicated in Annex V of the Machinery

Directive;

(The technical file must be kept and placed at the disposal of competent national authorities for

at least ten years from the date of manufacture of the motorised door);

- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery Direc-

tive and deliver it to the customer;

- affix the EC marking on the motorised door in accordance with point 1.7.3 of Annex I of the

Machine Directive.

arc

o P

iet

ro

Zin

i

(Pre

sid

ent

ent

ent

ent

en

en

)))

28

IP1639EN - 2015-05-13

3. Technical specifications

Ditec OBBI3BH Ditec OBBI3BFCH

Power supply 24 V= 24 V=
Absorption 3 A 3 A
Thrust 1500 N 1500 N
Max run 350 mm 350 mm
Opening time 25 s / 90° 25 s / 90°
Service class 3 - FREQUENT 3 - FREQUENT

Intermittence

S2 = 30 min
S3 = 50%

S2 = 30 min
S3 = 50%

Temperature

min -20° C
max +55° C

min -20° C
max +55° C

Degree of protection IP54 IP54
Control panel E2HOB E2HOB
Limit switch - Magnetic

Applications

m = leaf width
kg = leaf weight

Limit dimensions

Recommended
dimensions

500 kg

400 kg

300 kg

200 kg

100 kg

m12345

3.1 Operating instructions

Service life: 3 (minimum 10÷5 years of working life with 30÷60 cycles a day)
Applications: FREQUENT (For vehicle or pedestrian accesses to town houses or small condo­miniums with frequent use).

- Performance characteristics are to be understood as referring to the recommended weight
(approx. 2/3 of maximum permissible weight). When used with the maximum permissible weight
a reduction in the above mentioned performance can be expected.

- Service class, running times, and the number of consecutive cycles are to be taken as merely
indicative Having been statistically determined under average operating conditions, and are
therefore not necessarily applicable to specifi c conditions of use.

- Each automatic entrance has variable elements such as: friction, balancing and environmental
factors, all of which may substantially alter the performance characteristics of the automatic
entrance or curtail its working life or parts thereof (including the automatic devices themselves).
The installer should adopt suitable safety conditions for each particular installation.