Entre Matic NES600EH, NES300EHP, NES400EH, NES400EHP, NES400EHJ Technical Manual
...
Ditec NeoS / NeoS+
Sliding Gates
(Original instructions)
www.entrematic.com
IP2160EN
Technical Manual
28
IP2160EN - 2017-04-12
Contents
Key
Subject Page
1. General safety precautions 29
General safety precautions for the user 30
2. Declaration of incorporation of partly completed machinery 31
2.1 Machinery Directive 31
3. Technical specifications 32
3.1 Operating instructions 33
4. Standard installation 34
5. Dimensions 35
6. Main components 35
7. Installation 36
7.1 Preliminary checks 36
7.2 Base plate position 37
7.3 Gearmotor installation 38
7.4 Rack installation 39
7.5 Operation with encoder 40
7.6 Magnetic limit switch installation and adjustment 40
7.7 Chain drive kit installation 41
8. Electrical connections 43
8.1 Installation of internal photocell 44
9. Routine maintenance plan 44
Operating instructions 45
i
This symbol indicates instructions or notes regarding safety, to which special attention must be paid.
This symbol indicates useful information for the correct functioning of the product.
All the rights concerning this material are the exclusive property of Entrematic Group AB.
Although the contents of this publication have been drawn up with the greatest care, Entrematic Group AB
cannot be held responsible in any way for any damage caused by mistakes or omissions in this publication.
We reserve the right to make changes without prior notice.
Copying, scanning and changing in any way are expressly forbidden unless authorised in writing by Entrematic
Group AB.
29
IP2160EN - 2017-04-12
1. General safety precautions
This installation manual is intended for qualified personnel only.
Installation, electrical connections and adjustments must be performed by qualified personnel, in accordance with Good Working Methods and in compliance with the current regulations.
Read the instructions carefully before installing the product.
Bad installation could be dangerous.
The packaging materials (plastic, polystyrene, etc.) should not be discarded in the environ-
ment or left within reach of children, as they are a potential source of danger.
Before installing the product, make sure it is in perfect condition.
Do not install the product in explosive areas and atmospheres: the presence of inflammable
gas or fumes represents a serious safety hazard.
Before installing the motorisation device, make all the necessary structural modifications to
create safety clearance and to guard or isolate all the crushing, shearing, trapping and general
hazardous areas.
Make sure the existing structure is up to standard in terms of strength and stability. The motorisation device manufacturer is not responsible for failure to observe Good Working Methods
when building the frames to be motorised, or for any deformation during use.
The safety devices (photocells, safety edges, emergency stops, etc.) must be installed taking into
account: applicable laws and directives, Good Working Methods, installation premises, system
operating logic and the forces developed by the motorised door or gate.
The safety devices must protect against crushing, cutting, trapping and general danger areas
of the motorised door or gate.
Display the signs required by law to identify hazardous areas.
Each installation must bear a visible indication of the data identifying the motorised door
or gate.
When necessary, connect the motorised door or gate to an effective ear thing system that complies with the current safety standards.
During installation, maintenance and repair operations, cut off the power supply before
opening the cover to access the electrical parts.
The automation protection casing must be removed by qualified personnel only.
The electronic parts must be handled using earthed antistatic conductive arms. The manufacturer of the motorisation declines all responsibility if component parts not compatible with safe
and correct operation are fitted.
Only use original spare parts for repairing or replacing products.
The installer must supply all information concerning the automatic, manual and emergency operation of the motorised door or gate, and must provide the user with the operating instructions.
Failure to respect the information given in this manual
may cause personal injury or damage to the device.
Keep these instructions for future reference
30
IP2160EN - 2017-04-12
These precautions are an integral and essential part of the product
and must be supplied to the user.
Read them carefully since they contain important information on safe
installation, use and maintenance.
These instructions must be kept and forwarded to all possible future
users of the system.
This product must only be used for the specific purpose for which it
was designed.
Any other use is to be considered improper and therefore dangerous.
The manufacturer cannot be held responsible for any damage caused
by improper, incorrect or unreasonable use.
Avoid operating in the proximity of the hinges or moving mechanical
parts. Do not enter within the operating range of the motorised door
or gate while it is moving.
Do not obstruct the motion of the motorised door or gate, as this may
cause a dangerous situation.
The motorised door or gate may be used by children over the age of 8
and by people with reduced physical, sensorial or mental abilities, or
lack of experience or knowledge, as long as they are properly supervised
or have been instructed in the safe use of the device and the relative
hazards.
Children must be supervised to make sure they do not play with the
device, nor play/remain in the sphere of action of the motorised door
or gate.
Keep remote controls and/or any other command devices out of the
reach of children, to avoid any accidental activation of the motorised
door or gate.
In the event of a product fault or malfunction, turn off the power supply
switch. Do not attempt to repair or intervene directly, and contact only
qualified personnel.
Failure to comply with the above may cause a dangerous situation.
Any repair or technical intervention must be carried out by qualified
personnel.
Cleaning and maintenance work must not be carried out by children
unless they are supervised.
To ensure that the system works efficiently and correctly, the manufacturer’s indications must be complied with and only qualified personnel
must perform routine maintenance on the motorised door or gate. In
particular, regular checks are recommended in order to verify that the
safety devices are operating correctly.
All installation, maintenance and repair work must be documented and
General safety precautions for the user
31
IP2160EN - 2017-04-12
2. Declaration of incorporation of partly completed machinery
2.1 Machinery Directive
(Directive 2006/42/EC, Annex II-B)
The manufacturer Entrematic Group AB, with headquarters in Lodjursgatan 10, SE-261 44 Landskrona, Sweden, declares that the automation for Ditec sliding gates NES300EH, NES300EHP,
NES400EH, NES400EHP, NES600EH, NES600EHP, NES1000EHP:
- is designed to be installed on a manual gate to form a machine pursuant to Directive 2006/42/
EC. The manufacturer of the motorised gate must declare conformity with Directive 2006/42/
EC (annex II-A) prior to initial machine start-up;
- conforms to the applicable essential safety requirements indicated in ANNEX I, Chapter 1 of the
Directive 2006/42/EC;
- conforms to the Low Voltage Directive 2006/95/EC;
- conforms to the Electromagnetic Compatibility Directive 2004/108/EC:
- conforms to the R&TTE Directive 1999/5/EC;
- the technical documentation conforms to Annex VII-B of the Directive 2006/42/EC;
- the technical documentation is managed by Marco Pietro Zini with headquarters in Via Mons.
Banfi, 3 - 21042 Caronno Pertusella (VA) - ITALY;
- a copy of technical documentation will be provided to national competent authorities, following
a suitably justified request.
Lan dskr ona, 01-07-2014 Matteo Fino
(Chairman)
Pursuant to Machinery Directive (2006/42/EC) the installer who motorises a door or gate has the
same obligations as the manufacturer of machinery and as such must:
- prepare the technical data sheet which must contain the documents indicated in Annex V of the
Machinery Directive;
(The technical data sheet must be kept and placed at the disposal of competent national authori-
ties for at least ten years from the date of manufacture of the motorised door);
- draw up the EC Declaration of Conformity in accordance with Annex II-A of the Machinery Direc-
tive and deliver it to the customer;
- affix the EC marking on the motorised door or gate, in accordance with point 1.7.3 of Annex I of
the Machinery Directive;
- ensure compliance of the motorised door or gate with safety regulations, by installing the neces-
sary safety devices;
- carry out the safety test
, modifying parameters and (if used) from the menu;
- refer to the installation manual of the CS12E - CS12M control panel for the operating force
adjustments, in compliance with EN12453 and EN12445.
made available to the user.
Only lock and release the door wings when the motor is switched off.
Do not enter within the operating range of the wing.
To dispose of electrical and electronic equipment correctly, users
must take the product to special "recycling centres" provided by
the municipal authorities.
(
Chahh
32
IP2160EN - 2017-04-12
3. Technical specifications
Ditec NES300EH Ditec NES300EHP
Power supply 230 V~ 50/60Hz 230 V~ 50/60Hz
Absorption 1,2 A 1,2 A
Fuse F1,6A F1,6A
Thrust 300 N 300 N
Wing speed 0,1÷0,25 m/s 0,1÷0,25 m/s
Max stroke 12 m 12 m
Max wing weight 300 kg 300 kg
Service class 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min - S3 = 50% S2 = 30 min - S3 = 50%
Ambient
temperature
-20° C +55° C -20° C +55° C
Degree of protection IP24 IP24
Control panel CS12E CS12M
Ditec NES400EH Ditec NES400EHP Ditec NES400EHJ
Power supply 230 V~ 50/60Hz 230 V~ 50/60Hz 120 V~ 50/60Hz
Absorption 1,2 A 1,2 A 2,4 A
Fuse F2A F2A F4A
Thrust 400 N 400 N 400 N
Wing speed 0,1÷0,25 m/s 0,1÷0,25 m/s 0,1÷0,25 m/s
Max stroke 12 m 12 m 12 m
Max wing weight 400 kg 400 kg 400 kg
Service class 4 - INTENSE 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min - S3 = 50% S2 = 30 min - S3 = 50% S2 = 30 min - S3 = 50%
Ambient
temperature
-20° C +55° C -20° C +55° C -20° C +55° C
Degree of protection IP24 IP24 IP24
Control panel CS12E CS12M CS12E
Ditec NES600EH Ditec NES600EHP Ditec NES600EHJ
Power supply 230 V~ 50/60Hz 230 V~ 50/60Hz 120 V~ 50/60Hz
Absorption 1,5 A 1,5 A 3 A
Fuse F2A F2A F4A
Thrust 600 N 600 N 600 N
Wing speed 0,1÷0,24 m/s 0,1÷0,24 m/s 0,1÷0,24 m/s
Max stroke 20 m 20 m 20 m
Max wing weight 600 kg 600 kg 600 kg
Service class 4 - INTENSE 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
Ambient
temperature
-20° C +55° C -20° C +55° C -20° C +55° C
Degree of protection IP24 IP24 IP24
Control panel CS12E CS12M CS12E
33
IP2160EN - 2017-04-12
3.1 Operating instructions
Service class: 4 (minimum 10-5 years of working life with 100-200 cycles per day).
Applications: INTENSE (for apartment block, industrial and commercial entrances and car parks
with vehicle access or access for intense pedestrian use).
- Performance characteristics are to be understood as referring to the recommended weight (ap-
prox. 2/3 of maximum permissible weight). When used with the maximum permissible weight
a reduction in the above mentioned performance can be expected.
- Service class, running times, and the number of consecutive cycles are to be taken as merely
indicative, having been statistically determined under average operating conditions, and are
therefore not necessarily applicable to specific conditions of use.
- Each automatic entrance has variable elements such as: friction, balancing and environmental
factors, all of which may substantially alter the performance characteristics of the automatic
entrance or curtail its working life or parts thereof (including the automatic devices themselves).
The installer should adopt suitable safety conditions for each particular installation.
Ditec NES1000EHP Ditec NES1000EHPJ
Power supply 230 V~ 50/60Hz 120 V~ 50/60Hz
Absorption 2 A 4 A
Fuse F2,5 A F6,3A
Thrust 1000 N 1000 N
Wing speed 0,1÷0,19 m/s 0,1÷0,19 m/s
Max stroke 20 m 20 m
Max wing weight 1000 kg 1000 kg
Service class 4 - INTENSE 4 - INTENSE
Intermittence S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
Ambient
temperature
-20° C +55° C -20° C +55° C
Degree of protection IP24 IP24
Control panel CS12M CS12M
34
IP2160EN - 2017-04-12
4. Standard installation
Ref. Code Description
1 NES300
NES400
NES600
NES1000
300 kg gearmotor with control panel
400 kg gearmotor with control panel
600 kg gearmotor with control panel
1000 kg gearmotor with control panel
2 ZEN2 / ZEN4
ZEN2C / ZEN4C
Remote control
3 FL24 Flashing light
4 XEL5
LAN4
GOL4M
Key selector switch
Keypad
Wireless keypad
5 LIN2
XEL2
LAB4
Photocells
IP55 photocells
6 SOFA-SOFB
GOPAV
Safety edge
Radio system for safety edges
7 LAB9 Magnetic loop detector for passage control
A Connect the power supply to a type-approved omnipolar switch, with a contact opening distance of at
least 3 mm (not supplied).
The connections to the mains and low voltage wires (230V) must be made on an independent channel
separated from the connections to the command and safety devices (SELV = Safety Extra Low Voltage).
1 A
4
7
2
6
3
5
5
Loading...