Page 1
Swing Door Operator
EM EMSW EMO
User Manual
Original instructions
Page 2
CONTENTS - Original instructions
3Instructions for safe operation .......................................................................................................
4Congratulations on your new automatic door! ........................................................................
4Electronic equipment reception interference ...........................................................................
4Environmental requirements ..........................................................................................................
4Product liability ...................................................................................................................................
5Service .....................................................................................................................................................
5Intended use .........................................................................................................................................
5Technical specification ......................................................................................................................
6How the EM EMSW EMO works .....................................................................................................
7Regular safety checks .........................................................................................................................
10General accessories ............................................................................................................................
10Safety accessories ................................................................................................................................
10Troubleshooting ..................................................................................................................................
11Service/Maintenance .........................................................................................................................
11Other products from Entrematic Nordic .....................................................................................
12Declaration of conformity ................................................................................................................
© All rights in and to this material are the sole property of Entrematic Nordic AB. Copying, scanning, alterations
or modifications are expressly forbidden without the prior written consent of Entrematic Nordic AB. Rights
reserved for changes without prior notice.
Backtrack information: folder:Workspace Main, version:a328, Date:2016-06-21 time:08:19:27, state: Frozen
1005099-EMEI-9.0Issue 2016-06-212
Page 3
Instructions for safe operation
• Failure to observe theinformation in this manual may
result in personal injury or damage to equipment.
• To reduce the risk of injury to persons - use this operator with single or double pedestrian swinging or
folding doors only.
• Do not use the equipment if repair or adjustment is
necessary.
• Disconnect supply when cleaning or other maintenance is to be carried out.
• The operator can be used by childrenage8 andabove,
and persons with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, if
they have been given supervision or instruction by a
person responsible for their safety concerning safe
operator use and the possible hazards involved.
This does not however prevent those persons to use
the door where the operator is installed.
• Cleaning and user maintenance shall not be made by
children without supervision.
• Do not let children climb on or play with the door or
the fixed/remote controls.
• The doorset can beoperated automatically by sensors
or manually byactivators. It can alsobe used manually
as a door closer.
3Issue 2016-06-211005099-EMEI-9.0
Page 4
Congratulations on your new automatic door!
Entrematic Nordichas developedautomatic doorsfor morethan 50years. State-of-the-arttechnology
and carefully tested materials and components provide you with a superior product.
As withall othertechnical products,your automaticdoor requiresperiodic maintenanceand service.
It is essential that you know your automatic door (system) and that you recognize the importance
of maintaining it in compliance with applicable standards for safety.
Your local Entrematic Nordic-authorized representative is familiar with these standards, as well as
all applicable local codes and Entrematic Nordic recommendations forpower-operated pedestrian
doors. Service and adjustments performed by your Entrematic Nordic-authorized representative,
will ensure safe and proper operation of your automatic door unit.
Electronic equipment reception interference
The equipmentcomplies withthe EuropeanEMC directive(US marketFCC Part15), providedinstalled
according to Installation and Service manual.
The equipmentmay generate anduse radio frequencyenergy and ifnot installed andused properly,
it may cause interference to radio, television reception or other radio frequency type systems.
If other equipment does not fully comply with immunity requirements interference may occur.
There is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Re-orient the receiving antenna.
• Relocate the receiver with respect to the equipment.
• Move the receiver away from the equipment.
• Plug the receiver into a different outlet so that equipment and receiver are on different branch
circuits.
• Check that protective earth (PE) is connected.
If necessary,the usershould consult thedealer oran experiencedelectronics technicianfor additional
suggestions.
Environmental requirements
Entrematic Nordicproducts are equippedwith electronicsand may alsobe equipped with batteries
containing materials which are hazardous to the environment. Disconnect power before removing
electronics and battery and make sureit is disposed ofproperly according tolocal regulations (how
and where) as was done with the packaging material.
Product liability
According to regulations, the following are the responsibility of the owner or caretaker of the
equipment
• that the equipment operates correctly, so that it gives sufficient protection in regard to safety
and health
• that the equipment is operated and regularly maintained, inspected and serviced by someone
with documented competence in the equipment and in applicable regulations
• that theprovided “ServiceLog Book”and “SiteAcceptance Testand RiskAssessment” documents
are kept available for maintenance and service records
• that inspection covers the emergency opening function (when applicable)
• that the closing force is appropriate for the door size on fire-approved door systems (when ap-
plicable)
1005099-EMEI-9.0Issue 2016-06-214
Page 5
Service
Regular inspections bya trainedand qualifiedperson, and thefrequency ofservice occasions,should
at minimum be made according to national regulations or industry standard, in the absence of a
national regulation.This isespecially importantwhen the installation concerns a fire-approved door
or a door with an emergency-opening function. To extend the life of your investment and ensure
safe and reliable operation of the door, we recommend a minimum of 2 visits per year or more, depending on usage and operating conditions. Environmental aspects shall also be considered.
Talk to your Entrematic Nordic representative to learn more about our service offering.
Intended use
The EM EMSWEMO is an automatic swingdoor operator developed to make life easier for everyone
who can benefit from automatic doors. The EM EMSW EMO is a low-energy operator using a DC
motor anda gear-reductionsystem todrive anarm system,which opensthe door. It is to be installed
indoors where it is suitablefor almostall typesof externaland internalswing doors.This widely-used
operator can be found in applications in health care, residential, office and public buildings.
The door is designed to offer continuous use, a high degree of safety and maximum lifetime. The
system is self-adjusting to the effects caused by normal variations in the weather conditions and to
minor friction changes caused by e.g. dust and dirt.
For escape in emergency situations the doorset is opened manually.
For installation and maintenance see Installation and Service manual 1005088.
Save these instructions for future reference.
Technical specification
Entrematic Nordic ABManufacturer:
Lodjursgatan 10, SE-261 44 Landskrona, SwedenAddress:
EM EMSW EMOType:
100-240 V AC +10/-15%, 50/60 HzMains power supply:
Max. 75 WPower consumption:
IP20Class of protection:
Third party approvals from established certification organizations valid
for safety in use, see Declaration of Incorporation.
Approvals:
5Issue 2016-06-211005099-EMEI-9.0
Page 6
How the EM EMSW EMO works
The swing door operator EM EMSW EMO uses a DC motor and a gear-reduction system to drive an
arm system which opens the door. Closing power is provided by a motor and a closing spring. A
highly sophisticated electronic control unit uses a motor encoder and a microprocessor to control
the door’s movement.
To activate the operator you can use a manual activator (elbow switch) or an automatic activator
(radar device). It is also possible – where local standards allow – to activate the operator by just
pushing the door, if Push & Go is selected.
After the door has been activated it will open and stay open for a specified Hold Open Time (HOT).
When the HOT has elapsed the door will close.
The EM EMSW EMO can be set in three or four different modes, depending on programme selector
type, see table below.
In fully manual use (or in case of a power failure) the EM EMSW EMO acts as a normal door closer.
FunctionPosition
The door can be opened with the inner and outer manual and/or automatic activators. The electric strike, if fitted, is open.
AUTO
Normal
position
The door is closed. The door cannot be opened with inner and outer activation
units. The door is locked if an electromechanical locking device has been fitted.
The door can be opened with a key switch (if fitted).
OFF
The door is held permanently open and the motor is inactivated.OPEN
Passage from inside only. The door is normally locked if an electromechanical
locking devicehas beenfitted. Thedoor canonly beopened withthe inneractivation unit and with a key switch (if fitted).
EXIT
1005099-EMEI-9.0Issue 2016-06-216
Page 7
Regular safety checks
To help you fulfil the national/international requirements and to avoid malfunction and risk for injuries, we have provided the following checklist.
Do not use if repair or adjustment is necessary.
Disconnect supply14when cleaning or other maintenance is to be carried out.
If problem
occurs
Daily Action
Activate your operator and check visually, fastening and any damage of
•
operator
1
•
arm system
2
•
cables
3
•
hinges
5
•
door and glass
6
Also inspect your operator and check visually for
•
sharp edges on the door leaf and door frame (if any)
7
•
condition of door seals
8
•
finger protection
9
• and finally that the complete door runs properly and closes slowly in a smooth way
Set the programme selector to OFF and check that the operator and electromechanical lock
(if fitted) work together. Also check that the lock10really secures the door.
Activate the manualactivation units11, if any, andwalk towards the door. Checkthat the door
has opened appropriately while you pass the entrance/exit.
Then proceed with the automatic activation units12in the same way.
Check the non-monitored safety sensors13if any, by standing in the swing path and activate
the operator. The door must not hit you when opening nor when closing.
If you are unsureof which type of sensoryou have, please contact your EntrematicNordic representative.
Set theprogramme selector inAUTO mode.Push the doormanually
in escape direction and make sure that no object or function will
prevent the door from opening. Also make sure the escape route is
free for use.
By law, these tests must be performed
regularly by trained personnel.
Escape
doors
Let the door close after an impulse ensuring nothing prevents the
door from closing and locking (if regulations require it).
Fire
doors
Take appropriate measures.=
Contact your Entrematic Nordic representative. For contact information, see last page.=
7Issue 2016-06-211005099-EMEI-9.0
Page 8
FUNCTION AND VISUAL INSPECTION
6
7
10
12
8
3
3
4
3
11
13
9
5
1
2
4
3
14
CLEANING
The best way to remove dust and dirt from the EM EMSW EMO is to use water and a soft cloth or a sponge.
A gentle detergent may be used. To maintain the quality of the enamel layer, the surfaces should be cleaned
once/four months period. The cleaning should be documented. To avoid damages to the profiles the
brushes/weather stripping must be vacuum-cleaned weekly.
• Do not expose windows, doors or profiles to alkalis. Both aluminium and glass are sensitive to alkalis.
• Do not clean with high pressure water. Operator, programme selector and sensor may be damaged and
water may enter the profiles.
• Do not use polishing detergent.
• Do not scrub with materials like Scotch-brite, as this will cause mechanical damage.
1005099-EMEI-9.0Issue 2016-06-218
Page 9
SIGNAGE
Entrematic Group AB
LODJURSGATAN 10
LANDSKRONA SWEDEN
FACTORY NO. X
1004197
DESIGNATIONART. NO.
YEAR+WEEK
XXXXXXX XXXXXXXXXXXXX
TYPE
XXXXXXXXXX
TEMPERATURE
XXXXXXXXXXXXXXX
LOAD
XXXXX
PROD. ORDER
XXXXXXX
XXXXXX
XX/XX
Hz
PROJECT/SERIAL NO.
XXXXXXXXXXWXXXX
AVAC
xxxxxxx
xxxxxxx
1002
SÜD
1 2 3 4 5 6 7 8
CLASSIFICATION DIN 18650
SITAC XXXX
TG XXXXXX
Ersätter lås med fallkolv till
typgodkända
slagdörrar enl. förteckning
Skydd mot olyckor vid
rörliga anordningar
Click!
Click!
800 mm
F
E
B
C
G
D
A
No entry
1000 mm
No entry
H
If problem
occurs
Action
Check that all required signage isapplied and intact. Mandatory indicates that the signage is required by European directives and equivalent national legislation outside the European Union.
Product label: Mandatory
A
Emergency break-out: Mandatory, if approved for escape route.
B
Entrematic Nordic door sticker: Mandatory, if applicable to highlight the presence of the
glass (applied to all glass sections that are moving).
C
Supervision of child: Mandatory, if applicable (applied to both sides of the door). To be
placed on entrances where the risk analysis shows use by children, elderly and disabled.
D
Operator designed for disabled people:
Recommended, if applicable (applied to both sides of the door).
E
Activation by disabled people: Recommended, if applicable.
F
SITAC label: Mandatory in SE
G
No entry, identifying one-way traffic: Mandatory in GB and US, if applicable, not included
in the product.
H
Contact your Entrematic Nordic service representative. For contact information, see last page.=
9Issue 2016-06-211005099-EMEI-9.0
Page 10
General accessories
Your EM EMSW EMO can be further improved with the following add-ons (please contact your local
Entrematic Nordic dealer for detailed description).
•
Position switch4, see page 8
•
Electrical lock10, see page 8
•
Key switch11, see page 8
•
Elbow switch11, see page 8
•
Radar12, see page 8
• Wireless transmitters (not illustrated)
• Access control (not illustrated)
• Door stop (not illustrated)
Safety accessories
Even though the EM EMSW EMO is installed to comply with all applicable safety regulations, it is
possible toenhance safety/comfortwith thefollowing add-ons(please contactyour local Entrematic
Nordic company for detailed description).
•
Safety sensors13, see page 8.
•
Finger protection9, see page 8.
Troubleshooting
RemediesWhat´s wrong?
The door does not open
Change the setting of the program selector.
(See page 6).
The motor does not start
Check that there are no objects in the detection zone if a sensor is
fitted.
Check the mains switch and fuse in the building.
Unlock the mechanical locks.The motorstarts butdoor(s)
will not open
Check that nothing is jammed beneath the door.
Change the setting of the program selector.
(See page 6).
The door does not close
Check that there are no objects in the detection zone if a sensor is
fitted.
Check that nothing is jammed beneath the door.
Check that there are no moving objects within 1-1.5 m (39"-59")
from the door if an automatic activation unit is fitted.
The door opens and closes
continuously
If the problem continues, please contact your Entrematic Nordic representative.
1005099-EMEI-9.0Issue 2016-06-2110
Page 11
Service/Maintenance
Service andadjustments performedby yourEntrematic Nordic-authorizedrepresentative willensure
safe and proper operation of your automatic door unit.
Remember to keep “Service Log Book” and “Site Acceptance Test and Risk Assessment” documents
available. These are used together.
The tablebelow showsthe recommendedinterval inmonths, whento replaceparts duringpreventive
maintenance.
Abusive
Environment
Cycles/hour in operation
Part numberPart
>100<100<10
High
traffic
Medium
traffic
Low
traffic
661224330000485BK/SIPUSH/PUSH-335 service kit
661224330000486BK/SIPULL/PULL-220 service kit
661224331003887ST-V/H service kit
24242424331003567Battery backup unit *
60606060331003532CU-ESD control unit
Other products from Entrematic Nordic
• Door Systems
• Sliding doors
• Automatic and manual activation units
11Issue 2016-06-211005099-EMEI-9.0
Page 12
We
Entrematic Group AB
Lodjursgatan 10
SE-261 44 Landskrona
Sweden
declare under our sole responsibility that the type of equipment:
EM EMSW EMO
complies with the following directives:
2014/30/EU ElectroMagnetic Compatibility Directive (EMCD)
2006/42/EC Machinery Directive (MD)
Harmonized European standards which have been applied:
EN 60335-2-103:2003+A11:2009EN 60335-1:2012
EN 61000-6-3:2007+A1:2011EN 61000-6-2:2005
EN 16005:2012EN ISO 13849-1:2008
Other standards or technical specifications, which have been applied:
BVLBBR
UL 325FCC 47 CFR Part 15 B
IEC 60335-1:2010 ed. 5IEC 60335-2-103:2002 ed. 1/2011 ed. 2.1
EN 1634-1:2008DIN 18650-1/-2:2010
EC type examination or certificate issued by a notified or competent body (for full address, please contact Entrematic
Group AB) concerning the equipment:
TÜV B 11 08 74969 003SC0840-09
The manufacturing process ensures the compliance of the equipment with the technical file. The manufacturing
process is regularly assessed by 3rd party.
Compilation of technical file:
Email: christian.trobro@entrematic.comChristian Trobro
Entrematic Group AB
Lodjursgatan 10
SE-261 44 Landskrona
Sweden
PositionSignatureDatePlace
Product Safety & Liability ManagerChristian Trobro2016-04-20Landskrona
Declaration of conformity
DoC 1006796-EMEI-9.0
1005099-EMEI-9.0Issue 2016-06-2112
Page 13
Page 14
Entrematic Nordic AB, Lodjursgatan 10, SE-261 44 Landskrona, Sweden
Tel: +46 10 47 48 300
www.entrematic.com • info.em@entrematic.com
Loading...