Entrelec TS 32 Catalog Page
508
160T11050 060112
J
2
BADL 9 mm
PEAD
RCPEAD 29 x 9 mm
EPR2
PIE24
(1) 37 x 24 mm
PEB 35 x 17 mm
PEB 35 x 17 mm
PIB3 35 x 17 mm
PIB 35 x 17 mm
EPR1
P
EBM
PEH
RPEH 40 x 5 mm
RC810 8 mm
R
C1010 10 mm
RPA
PEAD PIE24
PEB - PIB...
RC...
BAM2 10 mm
BAM2 10 mm
BAM2 10 mm
BADL
BAM2
PEH
BADL
BAM2
Characteristics
Description Type Order P/N
PackagingWeight
kg
Screwless snap on end stop
grey (same colour as spring, ADO System
®
and ATEX blocks)
Selection
Accessories
Screwless, snaps on rail without tool. V0 grey polyamide for DIN 3 rail. Maintained in place and locked on the rail with metal grips.
To reposition, do not slide on the rail. Withdraw and snap again (screwdriver DIA. 6,5 mm .256" max.)
Thickness : 9 mm .354"
End stops
Adjustable marker-holder for end stop
grey
Card of 40 blank markers for
PEAD
Card of 20 transparent protection
markers for PEAD
Marker-holder, white engraving on black
background, screw mounting on BADL
Marker-holder snapped on end stop
(no marker included)
(screw range) gris
(Atex-Spring-ADO) gris
Strip of 7 markers for PEB, to be
printed with AMS500
Marker for PEB, white marking on
black background
Protection for PIB... marker
PEB marker holder with marker to be written by
hand or marking system, protection included
Horizontal marker-holder, slide mouting
on top of end stop
Card of 120 blank precut markers for
PEH
Markers see marking section
Characteristics
Description Type Order P/N
PackagingWeight
kg
End stop equipped with a steel clamp
grey (same colour as screw blocks)
grey (same colour as spring, ADO System
®
and ATEX blocks)
beige (same colour as railway blocks)
Selection
End stop of polyamide, equipped with a steel clamp allows mounting on PR3, PR4 and PR5 (DIN 3) rails.
Recommended screwdriver : DIA. 5,5 mm .217"
Recommended torque : Min. 0,8 mN - Max. 1 mN Min. 7.1 lb.in - Max. 8.9 lb.in
Thickness : 10 mm .394"
center of rail
(1) For BADL only
1SNA 399 903 R0
200
1SNA 206 351 R1
600
1SNA 399 967 R0
100
1SNA 296 351 R0
000
1SNA 399 719 R1
000
1SNA 399 725 R0
600
1SNA 399 726 R0
700
1SNA 007 871 R2
400
1SNA 113 077 R1
100
1SNA 195 077 R1
400
1SNA 235 462 R2
200
1SNA 173 812 R1
300
1SNA 178 431 R2
200
1SNA 113 084 R0
100
1SNA 163 211 R2
600
1SNA 163 007 R2
600
Type P/N Type P/N
Type P
/N
Mounting rails
Asymmetrical - D
IN 1
Symmetrical - D
IN 2
The “Series 5000” terminal blocks
snap onto the PR1 asymmetrical
D
IN 1 rails described here.
T
he “Series DR” terminal blocks snap
o
nto the PR2 symmetrical DIN 2 rail
d
escribed here.
T
hese rails are often used as
g
rounding bars. The current carrying
c
apacity of these rails and the copper
w
ire sizes required to carry that
c
urrent are given below.
TS 32 ALU
6F/23ST23ST
Asymmetrical 32 mm 1.26" G rail in
compliance with EN 50035 standard
(DIN
46277-1 - NFC 63018) DIN 1
Asymmetrical 32 mm 1.26" G rail in
compliance
with EN 50035 standard
(DIN
46277-1 - NFC 63018) DIN 1
Symmetrical
rail 15 mm .59" in
compliance
with EN 50045 standard
(DIN
46277.2)
TS 15/F
Current Wire size
Rail M
aterial (A) AWG mm
2
TS 32 Steel 143 2 35
TS 32 ALU A
luminum 265 000 95
TS 32/F6 S
teel 100 4 25
TS 15/F S
teel 35 12 4
TS 15 S
teel 47 10 6
PR1.Z2 (TS 32)
White passivated galvanized steel.
Length 2 m 6'6" (78") approx.
0163 050.04
Length 1 m 3'3" (39") approx.
0101 596.14
PR1.A2 (TS 32 ALU)
Aluminum alloy
Length 2 m 6'6" (78") approx.
0167 120.23
Length 1 m 3'3" (39") approx.
0101 603.07
PR2 (TS 15/F) 0101 673.00
Prepunched white passivated
galvanized steel.
Length 1 m 3'3" (39") approx.
PR2 (TS 15) 0101 674.01
Zinc bichromate plated steel.
Not prepunched.
Length 1 m 3'3" (39") approx.
PR1 (TS 32/F6)
Prepunched white passivated
galvanized steel.
Length 2 m 6'6" (78") approx.
0101 501.25
Length 1 m 3'3" (39") approx.
0101 511.16
One meter only.
Rail tolerances
Symmetrical - DIN 3
Rail length: supplied in lengths of 1 or 2 meters or in
custom cut lengths. Allow 3 mm for the rail cutting
b
lade thickness.
S
hown for DIN rails 35 mm wide and either 7.5 mm or
1
5 mm high. For other rail tolerances, contact Entrelec.
D
imensions apply over the whole length of the DIN rail,
b
ut shall not be verified anywhere less than 10 mm
f
rom the ends.
A
ll dimensions in millimeters.
Asymmetrical - DIN 1
Rail length: supplied in lengths of 1 or 2 meters or in
custom cut lengths. Allow 3 mm for the rail cutting
b
lade thickness.
Shown for DIN 1 rails 32 mm wide and 15 mm high.
D
imensions apply over the whole length of the DIN rail,
b
ut shall not be verified anywhere less than 10 mm
f
rom the ends.
A
ll dimensions in millimeters.
Loading...