Entrelec D 4/6.T3.P Catalog Page

T01046 001229

Triple-deck
terminal blocks

+ ground protection

Compression clamp

DIN 3

End stop th. 12 mm
End stop th. 9,1 mm
End stop th. 9,1 mm

Other end stops : see Accessories section

Rail 0164 800.03
Rail
Rail
Rail
Rail

35 x 7,5 x 1 PR3G2
35 x 7,5 x 1 PR3Z2 0174 300.17
35 x 7,5 x 1 PR30 0173 220.05
35 x 15 x 2,3 PR4 0168 500.12
35 x 15 x 1,5 PR5

Other rails : see Accessories section
Other accessories : see Accessories section

Notes

Block for three phase motor supply

or for connection of 4 wire sensors.

Accessories

2

3

4

5

BADH V2 0116 900.27
BAMH V0 0194 836.01
BAMH V2 0114 836.00

prepunched

prepunched

1 End section
2 Circuit separator white
3 Test socket
4 Test plug
5 Assembled jumper bar 32A

6

6 Comb type jumper bar
7 IDC jumper 24A

0101 598.26

M

3~

D 4/6.T3.P

Spacing 6 mm (.238")

Standard 6 mm block + ground protection.

Color Type Part numbers

3 "feed-through" circuits
1 clamp (4th level) electrically connected to the mounting rail
Grey V0

D 4/6.T3.P 0299 684.02

Characteristics

Wire size

IEC UL CSA

NFC DIN

Compression
clamp

Solid wire
Stranded wire

Voltage

Rated
Pulse
Pollution degree

Current

Rated / Short circuit

Wire size

Rated/gauge

Wire stripping Recommended Recommended Protection

length screwdriver torque

9,5 mm 4 mm 0,5-0,8 Nm IP 20

.37 " .16" 4.4-7 lb.in NEMA 1

Type Part numbers

No end section needed : closed block

SCD (3) V2 0103 189.26
AL2 (2) (3) 0167 319.06
FC2 (1) (3) 0007 865.26
BJM62 (3) 0173 217.26
BJM62 (3) 0173 218.07

32A

BJM62 (3) 0173 219.00

32A

BJM62 (3) 0173 221.22

32A

BJM62 (3) 0174 112.16

32A

BJM62 (3) 0174 113.17

32A

BJM62 (3) 0174 114.10

32A

BJM62 (3) 0174 115.11

32A

BJM62 (3) 0173 226.27

32A

PC61 0163 311.22
AD2,5 V2 0114 205.20

0,2-4 mm² 24-10 AWG 24-10 AWG

0,22-4 mm² 24-10 AWG 24-10 AWG

500 V 300 V 300 V

6 kV

3

32A - 480A/1s 20 A 20 A

4 mm² / A4 10 AWG 10 AWG

DIA. 2,0 mm
DIA. 2,0 mm

2 poles
3 poles
4 poles
5 poles
6 poles
7 poles
8 poles

9 poles
10 poles
10 poles

56

7

R

R See section on markers

marking method

5 RC65

Note : (1) For block equipped with AL2. (2) A circuit separator SCD is required with the use of these accessories.

blank (white, red, blue)

(3) Only for upper deck.