enTourage Pocket eDGe Quick Start Guide
Welcome to the digital version of the
Pocket eDGeTM Quick-Start Guide.
CONTENTS
Before you begin .................................................................................... 2
Unpack your Pocket eDGe .................................................................. 3
Turn on your Pocket eDGe .................................................................. 3
Set up your Pocket eDGe .................................................................... 3
In the box .................................................................................................. 4
What’s where ........................................................................................... 5
Frequently Asked Questions .............................................................. 6
Try these apps on the Pocket eDGe ................................................ 8
Tips for using apps ................................................................................ 9
FCC Notice ................................................................................................ 9
Quick-Start Guide
Welcome to your new Pocket eDGe! Follow these steps to get started.
Before You Begin
To set up your Pocket eDGe, you’ll need to have the following information on
hand. To save time, you can write it down here rst.
Your wireless network name (SSID): _______________________________________________
Your wireless network name is known as the SSID. This uniquely identies a network. This was
assigned when the wireless network was rst installed. The Pocket eDGe will automatically scan for
all networks and offer you a list of networks to connect to during Setup. If you are uncertain which
is your network please contact the installer of the wireless equipment.
Wireless security password: ________________________________________________________
Your wireless network might be password protected so others cannot connect to your network. If
your network is protected you will need to know the security password. Often this information is
located on or in the wireless router. If you don’t know your password please contact the installer of
the wireless equipment.
Your email address: _________________________________________________________________
The registration process requires an email address to register your product with enTourage
Systems and create a user account for purchasing books and backing up les. Use a valid email
address. This will not affect your email account.
A new password: ____________________________________________________________________
The password you create must be at least 8 characters long and include at least one number and
one letter. You will need it to use the enTourage eDGe Store.
Do you already have an account with Adobe? If so, record your account info
here. Otherwise, leave this section blank.
Adobe account email: ______________________________________________________________
Adobe account password: __________________________________________________________
You might have an Adobe account if you have downloaded some of their products. If you have an
existing Adobe account, you may want to link that account to your Pocket eDGe. During registration, touch the checkbox labeled “Use a different Username and Password for Adobe.” You will be
prompted for that account information.
Once you have recorded the information above, turn the page to continue.
Unpack your Pocket eDGe
Locate the AC adapter, the stylus (stored inside the tablet side of the Pocket
eDGe), and the mini-USB cable. Remove the lm from both screens, and also
the lm over the camera.
NOTE: The mini-USB cable is only for transferring les to your Pocket eDGe. You cannot use the miniUSB cable to charge your Pocket eDGe or connect it to the Internet.
Turn on your Pocket eDGe
You can start using your Pocket eDGe as soon as you plug it in, but you should
leave it plugged in for 4-6 hours the rst time to charge it completely. Connect
it to the AC adapter and connect the AC adapter to a wall outlet. To turn the
power on, slide the power switch. See the image on the back of this guide to
nd the power switch. The Power LED should light. (To turn the Pocket eDGe off
later, slide the power switch again and touch “Power off” on the tablet screen.)
Set up your Pocket eDGe
When you turn on your device for the rst time, the tablet screen will display
a welcome message. Touch anywhere on the tablet screen to begin the Setup
process. You can see your progress at the bottom of the tablet screen.
Anytime you see the icon, you can touch it to nd out more information.
If you have problems with any step, click here for Setup FAQs. If you still have
difculty, touch “Skip” to move to another step.
NOTE: If you do not have the latest software, you may not see a “Skip” button during Setup. If this is
the case and you need to break out of Setup, follow the instructions at this link.
1-2. CONNECT TO WI-FI
The rst step will help you connect to a Wi-Fi (wireless Internet) connection
if one is available. If you do not have a Wi-Fi connection available, or you
don’t know the password, touch Skip. If you have selected Skip, continue
reading below at Personalize Reader Screen.
NOTE: If you receive an error message, go to enTourageeDGe.com/support from a computer, and type
the message in the “Search Questions & Answers” bar. If you do not have a wireless network available,
you will need to connect to a wired network after you set up your Pocket eDGe. You can do so using an
Ethernet adapter purchased from enTourage Systems. See www.enTourageeDGe.com/accessories.html
for more information. You must connect to a network to register to buy books.
3. SET TIME ZONE
Select your time zone from the list. If your time zone is not listed, touch
“More Time Zones” for a complete list.
4-5. UPDATE
If you connect to Wi-Fi, your Pocket eDGe will automatically check for software updates. If there is an update available it will automatically download.
This can take some time depending on the speed of your connection. After
Loading...