Entone Hydra HD – B Serie, Hydra HD – Serie User Manual

Download

Page 1

Hydra High Definition

Multi-Television Video Gateway

User’s Guide

P/N: 95-82xxxx-xx

Page 2

©2007 Entone, Inc. All rights reserved. This document contains proprietary information protected by copyright. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Entone, Inc., 2755 Campus Drive, Suite 235, San Mateo, CA 94403. U.S.A.

DISCLAIMER

IF THIS PRODUCT DIRECTS YOU TO COPY MATERIALS, YOU MUST HAVE PERMISSION FROM THE COPYRIGHT OWNER OF THE MATERIALS TO AVOID VIOLATING THE LAW WHICH COULD RESULT IN DAMAGES OR OTHER REMEDIES.

TRADEMARKS

Entone and the tagline “Connecting the Home” are trademarks of Entone, Inc. All other trademarks or registered trademarks belong to their respective owners.

CHANGES

The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, Entone, Inc. assumes no liability resulting from the use of the information contained herein.

Entone, Inc. reserves the right to make changes in the product design without reservation and without notification to its users.

P/N: 95-82xxxx-xx August 2007

CUSTOMER SUPPORT AND CONTACT INFORMATION

For Customer Support please call: 650.572.7000

Customer Contact Information:

Entone, Inc. 2755 Campus Drive Suite 235 San Mateo, CA 94403 U.S.A. Tel: 650.572.7000

www.entone.com

Page 3

Table of Contents

Declaration of Conformity ................................................................................................................................................ 3

Preface............................................................................................................................................................................. 6

Introducing Hydra HD ...................................................................................................................................................... 6

TYPOGRAPHICAL CONVENTIONS................................................................................................................. 6

OVERVIEW OF THIS USER’S GUIDE..............................................................................................................6

1.1 Safety Precautions............................................................................................................................................... 7

OPERATION AND CARE.................................................................................................................................. 7

2.1 Index to Parts and Controls .................................................................................................................................8

CONTENTS IN THE BOX..................................................................................................................................8

FRONT PANEL AND REAR PANEL ................................................................................................................. 9

REMOTE CONTROL.......................................................................................................................................10

3.1 Hydra HD Introduction .......................................................................................................................................11

ABOUT THE HYDRA HIGH DEFINITION MULTI-TELEVISION VIDEO GATEWAY ..................................... 11

4.1 Connecting the Primary TV................................................................................................................................13

CONNECTING THE PRIMARY TV USING COAXIAL CABLE ....................................................................... 14

CONNECTING THE PRIMARY TV USING RCA COMPOSITE OR S-VIDEO ............................................... 15

CONNECTING THE PRIMARY TV USING HDMI OR COMPONENT............................................................17

SETTING HDMI AND COMPONENT OUTPUT RESOLUTION .....................................................................19

5.1 Connecting TV(s) In Other Rooms ....................................................................................................................20

CONNECTING TV(S) IN ANOTHER ROOM(S) USING CATV CABLING SYSTEM...................................... 21

SETTING UP TV TO USE CATV..................................................................................................................... 21

6.1 Connecting Audio System .................................................................................................................................22

7.1 Caller ID Display................................................................................................................................................24

8.1 Connecting eSATA Hard Drive..........................................................................................................................25

9.1 Powering-Up Hydra ........................................................................................................................................... 27

10.1 Remote Controls................................................................................................................................................ 29

LOADING BATTERIES.................................................................................................................................... 29

CONTROLLING THE HYDRA HD...................................................................................................................30

ATTACH THE RF REMOTE CONTROL ANTENNA....................................................................................... 31

REMOTE CONTROL REGISTRATION...........................................................................................................32

CONTROLLING YOUR TELEVISION AND OTHER A/V DEVICES ............................................................... 34

11.1 Closed Captioning .............................................................................................................................................35

12.1 Aspect Ratio....................................................................................................................................................... 36

13.1 User Menu......................................................................................................................................................... 37

USING USER MENU .......................................................................................................................................38

SETTING CHANNEL ID................................................................................................................................... 42

SETTING HDMI AND COMPONENT OUTPUT RESOLUTION .....................................................................42

Page 4

Hydra HD – B Series User’s Guide

SETTING CLOSED CAPTIONING..................................................................................................................42

SETTING FAN SPEED....................................................................................................................................42

SETTING HPNA...............................................................................................................................................43

SETTING TIVO IR KEYCODE......................................................................................................................... 43

14.1 Specifications.....................................................................................................................................................44

15.1 Troubleshooting the Hydra ................................................................................................................................ 46

Page 5

Declaration of Conformity

To ensure proper use of this product, please read this manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service location.

WARNING: This symbol indicates the presence of uninsulated dangerous voltage within the product's enclosure that constitutes a risk of electric shock. Do not open the product's case.

CAUTION: This symbol indicates you must take care; there is risk of damage to the equipment or to yourself.

To prevent fire or shock hazard, do not expose this product to rain or moisture. To reduce the risk of electric shock, DO NOT remove the cover or back. No user serviceable parts are inside. For servicing refer to qualified personnel.

Declaration of Conformity (United States Only)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communication Commission (FCC) Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the

receiver.

• Connect the equipment to a different circuit from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Page 6

Hydra HD – B Series User’s Guide

Part 68 - Compliance Registration

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. A label on the bottom of this equipment contains, among other information, the Ringer Equivalence Number (REN) and the product identifier. For products approved after July 23, 2001 the product identifier is in the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g. 03 is a REN of 0.3). The REN is used to determine the number of devices that may be connected to a telephone line. For earlier products, the REN is separately shown on the label. If requested, this number must be provided to the telephone company. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. This equipment is designed to connect to the telephone network or premises wiring using a compatible modular jack that is Part 68 compliant. An FCC compliant telephone cord and modular plug is provided with the equipment. If this terminal equipment causes harm to the telephone network, the telephone company may request you to disconnect the equipment until the problem is resolved. The telephone company will notify you in advance if temporary discontinuance of service is required. If advance notification is not practical, the telephone company will notify you as soon as possible. You will be advised of your right to file a complaint with the FCC if you believe such action is necessary. If you experience trouble with this equipment, do not try to repair the equipment yourself. The equipment cannot be repaired in the field. Contact your ISP for further instructions. The telephone company may make changes to their facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice in order for you to make the modifications necessary to maintain uninterrupted service. If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. This equipment cannot be used on public coin phone service provided by the telephone company. Connection of this equipment to party line service is subject to state tariffs.

Declaration of Conformity (Europe Only)

This product is in conformity with the Council Directives:

• EMC Directive 89/336/EEC

• Low voltage Directive 73/23/EEC

Entone products are designed and tested to meet IEC00065, the standard for the Safety of Information Technology Equipment. This is the international standard for these types of products to reduce the risk of product damage and of personal injury. The standard protects against the following hazards:

• Electric shock

• Hazardous voltage levels

• Fire — Overload, temperature, material flammability

• Energy — Circuit with high energy or potential as burn hazards

• Heat — Accessible part of the product at high temperatures

• Radiation

• Noise

Page 7

Hydra HD – B Series User’s Guide

Canada Certification Notice The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operations and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The department does not guarantee the equipment will operate to the user’s satisfaction. This equipment meets the applicable Industry Canada Terminal Equipment Technical Specification. This is confirmed by the registration number. The abbreviation, IC, before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. The Ringer Equivalence Number (REN) is 0.0. The Ringer Equivalence Number that is assigned to each piece of terminal equipment provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed

5.0. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local Telecommunication Company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Connection to a party line service is subject to state tariffs. Contact the state public utility commission, public service commission, or corporation commission for information. If your home has specially wired alarm equipment connected to the telephone line, ensure that the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. If you experience trouble with this equipment, do not try to repair the equipment yourself. The equipment cannot be repaired in the field and must be returned to the manufacturer. Repairs to certified equipment should be coordinated by a representative, and designated by the supplier. Users should ensure, for their own protection, that the electrical ground connections of the power utility, telephone lines, and internal, metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. CAUTION: Users should not attempt to make such connections themselves, but should contact the appropriate electrical inspection authority, or electrician, as appropriate.

Page 8

Hydra HD – B Series User’s Guide

Preface

Introducing Hydra HD

TYPOGRAPHICAL CONVENTIONS

The following typographic conventions are used in this manual to provide visual clues as to the purpose or specific features of the IOM application.



Bold text describes menu options and selections displayed on the screen.



Italics emphasize statements and points to reference documentation.



Ellipses (…) indicate truncated text for long examples depicting output that is too long to be shown in its entirety.



NOTE/TIP: A note or a tip describes actions or conditions that can help you obtain optimum performance from IOM.



WARNING: A caution or a warning describes conditions that can result in an error.



IMPORTANT: An important note.

OVERVIEW OF THIS USER’S GUIDE

This User’s Guide provides generic information about connecting Hydra HD to your audio and video equipments. Some of the topics covered in this guide are:



Safety and regulatory information



Setup



Connecting Hydra HD to your audio and video equipment



Connecting Hydra HD to the network



Powering Hydra HD



Using the Remote Controls



Troubleshooting

For a full listing of all of the topics covered in this User’s Guide, see the Table of Contents.

Page 9

Chapter

1.1 Safety Precautions

Before installing Hydra HD, be sure to unplug Hydra HD, your TV and any other audio-video equipment you are using. This precaution will help to prevent danger of electrical shock and damage to Hydra HD and your equipment.

Be careful when moving your television to avoid accidental tipping or movements that might cause injury to you or those around you.

To ensure proper use of this product, please read this user manual carefully and retain for future reference. Should the unit require maintenance, contact your service provider.

OPERATION AND CARE



To prevent fire or shock hazard, do not expose this product to rain or moisture.



To reduce the risk of electric shock, DO NOT remove cover or back. No user serviceable parts inside. Refer servicing to qualified personnel.



To help prevent electric shock, plug the power cable into properly grounded sources. Use only properly grounded extension cords and adaptors, if they are needed.



Make sure nothing is lying on any of the cables.



Be sure the cables are located where they will not be stepped on or tripped over.



Do not spill food or liquids onto the unit.



Do not push any objects into the free slots. Doing so will damage the unit, can cause fire or electrical shock, and can short out interior components.



Keep the equipment away from heat sources and radiators.



Do not block cooling vents.



Do not place the equipment in a closed-in wall unit.



When you disconnect a cable, pull on its connector or on its strain relief loop, not on the cable itself. Some cables have a connector with locking tabs; if you are disconnecting this type of cable, press in on the locking tabs before disconnecting the cables.



When you connect a cable, make sure both connectors are correctly oriented and aligned before connecting to avoid bending connector pins.

Page 10

Chapter

2.1 Index to Parts and Controls

CONTENTS IN THE BOX

Item Picture Quantity

Hydra High Definition Multi-Television Video Gateway (Hydra HD)

RF Remote Control Antenna

RF Cable (with F type connectors) (6 feet)

RJ11 Telephone Wire (15 feet)

RJ45 Ethernet Cable (10 feet)

3 Color RCA A/V Cable (6 feet)

3 Color Component Cable (6 feet)

Power Supply with 6 feet power cord (100-240V, output 12V/2A; 5.2V/5A)

URC PLUS Remote Control (Universal Remote Control)

Battery (AA-size)

Page 11

Hydra HD – B Series User’s Guide

FRONT PANEL AND REAR PANEL

Figure 2-1 Hydra HD Front Panel

Part Name Description

1. Standby Switch Power up or put Hydra HD in standby mode

2. Smart Card Slot For future use

3. Standby / On Indicator Orange in standby mode and starting Green when started

4. IR receiver Remote control IR receiver

5. Arrow Keys UP arrow for setting HDMI and Component resolution Other usage according to middleware

6. Front Panel Display Start-up messages Clock after starting

7. OK Button Trigger remote registration mode Other usage according to middleware

8. Reset Pin Hole Restart Hydra HD

Figure 2-2 Hydra Rear Panel

Part Name Description

1. SATA eSATA port for connecting to external SATA hard drive for DVR and PLTV

2. DIGITAL AUDIO S/PDIF digital coaxial RCA audio output for decoder 1

3. S-VIDEO S-Video output for decoder 1

4. OPTICAL AUDIO S/PDIF digital optical audio TOSLINK output for decoder 1

5. HDMI HDMI output for decoder 1

6. AUDIO LEFT / RIGHT Composite audio output for decoder 1

7. VIDEO Composite video output for decoder 1

8. Y Pb Pr Component video output for decoder 1

9. TV OUT RF Type-F connector for decoder 1 (factory set to channel 10)

10. ATSC IN Optional RF Type-F connector for ATSC coaxial input

11. MATV OUT RF Type-F connector for decoder 1, 2 and 3 (factory set to channel 10, 23 and 39)

12. Caller ID RJ11 plug for connecting to telephone line for caller ID display

13. USB x 2 2 x USB port for future use

14. ETHERNET RJ45 plug for connecting to ADSL modem or network access equipment

15. REMOTE ANTENNA RF Type-F connector for connecting the RF remote control antenna

16. DC INPUT DC power jack

Page 12

Hydra HD – B Series User’s Guide

REMOTE CONTROL

Figure 2-3 Remote Control

NOTE: Please refer to your service

operator or middleware vendor for detailed functions and usages.

Part Name Description

1. SETUP Special Key reserved for remote programming functions.

2. INPUT Changes the current A/V input of the selected device. INPUT + MENU triggers STB User Menu.

3. POWER Switches the power on/off for the currently selected device. Switches STB to power on/standby mode.

4. STB Puts remote control in STB mode. Presses for more than 5s will trigger remote control registration mode.

5. TV Selects to control TV

6. LANG Toggles closed captioning on or off on decoder 1.

7. GUIDE Displays electronic program guide.

8. VOL + /- Raises or lowers volume of the currently selected device.

9. LAST Changes channel to the most recently viewed channel.

10. PAUSE Pause button for VOD or live channel.

11. PREVIOUS / NEXT

CHAPTER

Goes to previous or next movie chapter for VOD.

12. FAST REVERSE /

FORWARD

Starts fast reverse or fast forward for VOD or live channel.

13. RED *

14. GREEN *

15. NUMBER KEYS Allows direct access to specific channels and menu items.

16. ENTER *

17. DTV Returns to live programming.

18. Movies Displays the VOD menu.

19. Record-it Displays the digital recorder menu.

20. Promos Displays the promotion menu.

21. AUX Selects to control AUX device.

22. INFO Displays on-screen information about the current television program.

23. MENU Displays the on-screen menu. INPUT + MENU triggers STB User Menu.

24. EXIT Exits the current menu item.

25. CH UP / DOWN Changes channel up or down.

26. RECORD Records live channel.

27. STOP Stop button for VOD or live channel.

28. ARROW KEYS Navigates right, left, up, down in the on-screen guide.

29. OK Executes the currently selected menu option.

30. PLAY Play button for VOD or live channel.

31. BLUE *

32. YELLOW *

33. MUTE Turns the volume of the currently selected device off.

34. Media Displays the web menu.

35. Music Displays available music channels.

36. Help Displays the help menu.

37. Phone Displays the Caller ID menu.

Page 13

Chapter

3.1 Hydra HD Introduction

ABOUT THE HYDRA HIGH DEFINITION MULTI-TELEVISION VIDEO GATEWAY

Hydra HD is part of Entone’s Connected Home Solution. By leveraging existing in-home coax cabling, the Hydra HD offers consumers the ability to share electronics across multiple televisions, thus eliminating the need for multiple set-top boxes and new home wiring. It provides three streams of fully independent video with any combination of SD/HD, MPEG-2, and MPEG-4 (AVC/H.264) signals, over a single DSL, HomePNA, or Ethernet connection.

Hydra HD can support up to three concurrent streams playing on different TVs. The Hydra HD can be connected to a nearby TV and TV(s) located in another room(s). You can tune your TV to one of the 3 decoders. Each remote control can be registered for one decoder. You use the registered remote control to control the decoder.

Figure 3-1 Hydra HD Connecting the Home

Page 14

Hydra HD – B Series User’s Guide

Hydra HD comes with integrated Caller ID and optional features such as an integrated ATSC/DVB-T tuner for receiving over-the-air broadcast programming, and an integrated HomePNA interface for high-speed broadband Internet service over existing in-home coax and phone line. It supports interoperability and IP networking standards and protocols. Hydra HD helps protect service operators from service theft and content piracy by providing security features such as integrated DVB/DES descrambling, conditional access and, optionally, Macrovision’s anti-taping support.

Hydra HD supports full digital video recording capabilities, such as fast forward, rewind, and pause with an optional internal or external SATA hard drive. This enables service operators to deliver whole-home DVR services without having to install a set-top box at each television. Hydra HD offers a modular DVR with storage capacity of up to one terabyte.

Page 15

Chapter

4.1 Connecting the Primary TV

Hydra HD offers several options for connecting audio and video to popular TV and audio equipment.

You can connect Hydra HD to the primary TV using composite, component, S-Video or HDMI connection. You may also connect the Hydra HD to the primary TV using coaxial cable connection.

If your TV supports 480p, 720p or 1080i pictures, use the HDMI or the component output jacks to connect to your primary TV. HDMI stands for High Definition Multimedia Interface. HDMI transfers digital audio and uncompressed digital video on a single cable. As a result, audio cables and video cables do not need to be connected separately. The HDMI output jack is designed to HDMI version 1.1 specifications.

HDMI and component video output support high definition video signal. They will provide the best quality video signal for HD ready TV sets.

S-Video output will provide the best quality video signal for late-model TV sets. The RCA A/V composite, SVideo and TV OUT RF output jacks only support 480i pictures.

The following table shows the video and audio output jacks and their supported video formats:

Table 4-1 Video Format

Video Output Audio Output Format

HDMI No separate audio output

required

1080i60, 720p60, 480p60, 480i60 (Selectable and default to 720p60. Please refer to section Setting

HDMI and Component Output Resolution)

Component RCA Audio 1080i60, 720p60, 480p60, 480i60

(Selectable and default to 720p60. Please refer to section Setting

HDMI and Component Output Resolution)

S-Video, RCA Composite

RCA Audio 480i60

TV OUT/MATV OUT No separate audio output

required

480i60

Page 16

Hydra HD – B Series User’s Guide

CONNECTING THE PRIMARY TV USING COAXIAL CABLE

1. Use the coaxial cable that comes packaged with Hydra HD to connect your TV’s antenna input to the Hydra HD’s “TV OUT”.

2. Tune your TV to channel 10 to view the output.

NOTE:



In the “TV OUT”, it is always hooked to decoder 1 and factory set to use channel 10.



To set “TV OUT” to another channel ID, please refer to section Setting Channel ID.

Figure 4-1 Connecting Primary TV using Coaxial Cable

Page 17

Hydra HD – B Series User’s Guide

CONNECTING THE PRIMARY TV USING RCA COMPOSITE OR S-VIDEO

1. Acquire the required cable. RCA cable comes packaged with the Hydra HD. S-Video cable is not

packaged with the Hydra HD. Before purchasing the cable, consult your TV owner’s manual to confirm that your TV supports the video signal output that you plan to use.

2. Connect the video and audio cables to the Hydra HD.

3. Connect the opposite end of the video and audio cables to the matching input in the TV.

4. Plug in your TV and turn on the power using your TV remote control. Use your TV remote control to

select the respective video input that has connected to the Hydra HD. Consult your TV owner’s manual for instructions as required.

5. Plug in your Hydra HD and turn on the power.

6. You should now see the output from the Hydra HD on your TV screen.

Figure 4-2 Connecting Primary TV using RCA Composite Video/Audio

Page 18

Hydra HD – B Series User’s Guide

Figure 4-3 Connecting Primary TV using S-Video and Composite Audio

NOTE:



All the A/V outputs are always hooked to decoder 1.



Composite and S-Video outputs are always set to 480i.

Page 19

Hydra HD – B Series User’s Guide

CONNECTING THE PRIMARY TV USING HDMI OR COMPONENT

1. Acquire the required cable. Component cable comes packaged with the Hydra HD. HDMI cable is not

packaged with the Hydra HD. Before purchasing the cable, consult your TV owner’s manual to confirm that your TV supports the video signal output that you plan to use.

2. Connect the video and audio cables to the Hydra HD. (HDMI does not require separate audio cable

connection.)

3. Connect the opposite end of the video and audio cables to the matching input in the TV.

4. Plug in your TV and turn on the power using your TV remote control. Use your TV remote control to

select the respective video input that has connected to the Hydra HD. Consult your TV owner’s manual for instructions as required.

5. Plug in your Hydra HD and turn on the power.

6. You should now see the output from the Hydra HD on your TV screen.

Figure 4-4 Connecting Primary TV using Component and Composite Audio

Page 20

Hydra HD – B Series User’s Guide

Figure 4-5 Connecting Primary TV using HDMI

NOTE:



All the A/V outputs are always hooked to decoder 1.



HDMI is an evolving technology, so it is possible that some TVs may not operate properly with Hydra HD. Component output is the preferred way to connect to your HD TV.



When the HDMI connection cannot be verified by your TV, disconnect the HDMI cable and then connect it again, or turn off the TV and then turn it on again.



Analog DVI is not supported. If your TV supports digital DVI but not HDMI, you can use an HDMI to DVI convector cable or adaptor to connect the Hydra HD HDMI to the TV DVI. In this case, you need to connect the audio cable separately.



Be sure to use an HDMI cable with the HDMI logo.



If your TV does not support multi-channel audio, the Hydra HD will output PCM audio only.



Please refer to the next section to set the Component and HDMI output resolution.

Page 21

Hydra HD – B Series User’s Guide

SETTING HDMI AND COMPONENT OUTPUT RESOLUTION

You can select 1080i, 720p, 480p or 480i on the HDMI and Component output. When you set the output, both HDMI and Component outputs are set to the selected resolution. The S-Video, RCA Composite and RF outputs are always set to 480i and will not be affected by the HDMI and Component resolution setting.

To select the HDMI and Component output resolution:

1. Press and hold the Hydra HD front panel “UP” arrow for 5 seconds.

2. Keep on pressing the “UP” arrow, the resolution indicator in the Hydra HD front panel display will

illuminate in a round robin manner from “1080i -> 720p -> 480p -> 480i”.

3. When your desired resolution is illuminated, release the “UP” arrow. Then, both the HDMI and

Component outputs will be set to the selected resolution.

Figure 4-5 Setting HDMI and Component Output Resolution

NOTE: If your TV does not display the video or error message is displayed after you have selected a new resolution, your TV may not support the selected resolution. Refer to your TV owner’s manual for verification. Repeat the above procedures again to find a resolution supported by your TV.

Page 22

Chapter

5.1 Connecting TV(s) In Other Rooms

This section describes how to connect the Hydra HD to the cable-ready remote TV(s) located in another room(s) away from the Hydra HD. This installation uses your in-home TV cabling system. If your house does not have built-in TV cabling, it will be necessary to run cables from the Hydra HD to each remote TV. Due to the difficulty of this installation, you should consider having this professionally installed.

NOTE: When connecting to the in-home cabling system, you must meet the FCC requirements. To meet these requirements, an in-line coaxial attenuator may need to be installed using the following guidance:



If connecting to your in-home cabling system to distribute the signal to TV(s) in other rooms, in most cases you will not have to install the attenuator on the “MATV OUT” port for typical in-home cabling systems.



If connecting directly to a TV tuner port, you must install the attenuator in the cable between the “MATV OUT” port and the TV tuner.

Figure 5-1 Connecting Attenuator

Page 23

Hydra HD – B Series User’s Guide

CONNECTING TV(S) IN ANOTHER ROOM(S) USING CATV CABLING SYSTEM

Follow these steps to use the in-home cabling system:

1. Connect “MATV OUT” to the main video source of your in-home cabling system using the RF cable

provided.

2. Connect the tuner input of the remote TV(s) in other rooms to an existing wall cable outlet using a RF

cable.

3. Plug in your Hydra HD and turn on the power using your remote control.

4. Plug in your TV.

5. Tune the other TV sets to channel 10 for decoder 1, channel 23 for decoder 2 and channel 39 for

decoder 3.

NOTE: In the “MATV OUT”, the Hydra HD is factory set to use channel 10 for decoder 1, channel 23 for decoder 2 and channel 39 for decoder 3.

Figure 5-2 Connecting TV(s) in Another Room(s)

SETTING UP TV TO USE CATV

In order for the Hydra HD to feed video signal to TV using “TV OUT” or “MATV OUT”, your TV must be configured to receive signal from CATV rather than from the antenna.

Most TVs use either a physical switch located on the rear of the TV or with on-screen programming to configure to use CATV. Consult your TV owner’s manual for instruction if required.

Page 24

Chapter

6.1 Connecting Audio System

Your Hydra HD supports AC-3 (Dolby Digital 5.1 channel). To enjoy multi-channel surround-sound, the content source must carry multi-channel AC-3 signal. Please refer to your service provider for availability of AC-3 5.1 programs.

You can enjoy multi-channel surround-sound such as 5.1 channel by connecting the Hydra HD to an amplifier compatible with Dolby Digital. You can connect to your amplifier by either using the 75ohm digital audio coaxial output or the digital optical audio output.

Figure 6-1 Connecting Hydra HD to Audio System

Consult your audio system user guide for connection. Take necessary precautions when working with electric equipment. Remove the devices from wall power and be sure to use caution when moving equipment to prevent injury.

If your connected TV or A/V equipment does not support AC-3, you can disable AC-3. You can enable or disable AC-3 per decoder.

Enabling or disabling AC-3 is controlled by the IPTV middleware. For details of enabling and disabling AC-3, please refer to usage instruction provided by your service operator.

Page 25

Hydra HD – B Series User’s Guide

Please refer to the following table for details of audio output used when AC-3 is enabled or disabled.

Table 6-1 Audio Format

Audio Track

Decoder 1 HDMI

Decoder 1 Digital Coaxial and Optical Audio Output

RCA Audio Output

TV OUT and MATV OUT

AC-3 Enable

With AC3 Track

AC-3 track selected and output in AC-3

AC-3 track

selected and down-mixed to analog audio

AC-3 track selected and down-mixed to analog audio

AC-3 Enable

Normal Audio Track Only

PCM PCM Analog audio Analog audio

AC-3 Disable

With Normal Audio Track

Normal audio track selected and output in PCM

Normal audio

track selected and output in Analog audio

Normal audio track selected and output in Analog audio

AC-3 Disable

AC-3 Track Only

Down-mixed PCM

Down-mixed

analog audio

Down-mixed analog audio

WARNING: When connecting via the digital coaxial or optical audio output to a TV or A/V decoder that does not have Dolby Digital decoding capability, be sure to set AC-3 off to avoid damage to equipment.

Page 26

Chapter

7.1 Caller ID Display

The Hydra HD can display caller ID information of telephone incoming call on TV. In order to enjoy this service, your telephone line and TV service must have caller ID already set up. Check with your telephone and TV service provider on how to enable caller ID service.

To get ready your Hydra HD to enable caller ID service:

1. Connect the telephone line to the “CALLER ID” jack on the rear panel. Telephone wire comes

packaged with the Hydra HD. You may connect directly to the telephone line socket if there is one available. If your telephone line socket is already connecting to an existing phone, use a splitter.

2. For details of setting up and using the caller ID service, consult your TV service user guide.

Figure 7-1 Connecting Hydra HD for Caller ID Display

Page 27

Chapter

8.1 Connecting eSATA Hard Drive

Hydra HD supports DVR (Digital Video Recording) and PLTV (Pause Live TV) by using an internal or external eSATA (External Serial Advanced Technology Attachment) hard drive. This section applies when you need to install an external eSATA hard drive.

DVR allows you to record live or scheduled channel programs into the hard drive and view those recorded programs as VOD at later times. PLTV allows you to pause and fast track live programs. For details of DVR and PLTV service availability and operation usage, please refer to your network and TV service provider.

eSATA hard drive is an optional item. eSATA is an external interface for SATA technologies. The SATA interface is more streamlined than ATA and provides serial architecture for greater speed than the older parallel technology.

To get ready your Hydra HD to enable DVR and PLTV service:

1. Connect the external hard drive using eSATA cable.

2. The eSATA hard drive requires separate power supply. Connect the eSATA hard drive power supply to

the power source.

Figure 8-1 Connecting eSATA hard drive

Page 28

Hydra HD – B Series User’s Guide

When you connect a new hard drive for the first time, hard drive formatting is required. After hard drive formatting, all existing data in hard drive will be erased. When Hydra HD boots up, a confirming message will be displayed for 30s before formatting. If you decide not to proceed the formatting, power off Hydra HD and remove the hard drive.

Figure 8-2 Confirming eSATA hard drive formatting

Message will be showing when the hard drive is being formatted. The hard drive formatting may take up to 10 min depending on the hard drive size. Do not power off Hydra HD and hard drive during disk formatting.

Figure 8-3 eSATA hard drive formatting

ATTENTION: Connect power to the hard drive before powering up Hydra HD. If you power up Hydra HD before powering up the hard drive, the DVR and PLTV service will not be available.

ATTENTION: When you connect a new hard drive for the first time, Hydra HD will display message saying the hard drive is being formatted when it boots up. The hard drive formatting may take up to 10 min depending on the hard drive size. Do not power off Hydra HD and hard drive during disk formatting.

Page 29

Chapter

9.1 Powering-Up Hydra

Follow these steps to power up the Hydra HD:

1. Follow your TV/Network service provider’s instruction to connect the Hydra HD to your network modem

or network access unit using the Ethernet cable comes packaged with the Hydra HD.

Figure 9-1 Connecting Hydra HD

2. Plug the socket end of the AC/DC adapter into the wall socket and the DC jack into the power

connector on the Hydra HD.

3. The Hydra HD front panel power indicator will illuminate in orange color.

4. Within 10 seconds the Hydra HD front panel will display “BOOT” and then “WELCOME”.

Figure 9-2 Hydra HD Starting

Page 30

Hydra HD – B Series User’s Guide

5. Within 60 seconds splash screen will appear on the TV.

Figure 9-3 Hydra HD Boot-up Splash Screen

6. The total boot-up time may vary depending on the middleware application and the service provider

environment.

ATTENTION: If you have eSATA hard drive, connect power to the hard drive before powering up Hydra HD. If you power up Hydra HD before powering up the hard drive, the DVR and PLTV service will not be available. Please refer to previous section Connecting eSATA Hard Drive for details.

Page 31

Chapter

10.1 Remote Controls

LOADING BATTERIES

The remote controls come with AA-size batteries, which need to be installed when you first receive your system. When you replace old batteries, you should replace all of the batteries. Use batteries of the same kind, for example alkaline or carbon zinc, and do not mix batteries of different kinds. Alkaline batteries last longer than carbon zinc.

WARNING: Mixing old and new batteries or different types of batteries poses a fire hazard.

To load batteries to remote control:

1. Press down on the battery cover’s top latch and slide the cover off.

2. If you are changing out batteries, take out all of the old batteries.

3. Put the new batteries in. Make sure you match the plus ( “+” ) ends with the plus markings on the

battery case.

4. Slide the cover back into place.

Figure 10-1 Loading Batteries to Remote Control

Page 32

Hydra HD – B Series User’s Guide

CONTROLLING THE HYDRA HD

Hydra HD is equipped with specially designed remote controls. The remote controls use radio signals to control the Hydra HD operations. These radio signals travel over long distances and go though walls and other solid objects.

Your Hydra HD comes with 3 remote controls. (Additional remote controls can be purchased separately.) Your remote controls must be registered to one of the 3 decoders before it can be used. One remote control can only be registered to one decoder. However, you can register at most 3 remote controls to a decoder. After registration, you need to use the corresponding remote controls to control the decoders.

Figure 10-2 Controlling Hydra HD using RF Remote Control

ATTENTION: Hydra HD B-Series boxes must use new URC PLUS remote controls. Old remote controls without the “URC PLUS” logo do not work with Hydra HD B-Series boxes.

Page 33

Hydra HD – B Series User’s Guide

ATTACH THE RF REMOTE CONTROL ANTENNA

You need to attach the RF Remote Control Antenna to the Hydra HD’s rear panel “REMOTE ANTENNA” input in order to use the radio control remotes.

Figure 10-3 Attaching Remote Control Antenna

NOTE: Be sure to set the antenna straight up so that you can use the remote control from as far away as possible. Don’t let the antenna touch anything.

ATTENTION: If your remote control isn’t working very well from far away, you may be experiencing interference from objects near your receiver. To improve your remote control’s range, try any or all of the followings:

1. Place the receiver higher than all of the other equipment in your entertainment center.

2. Provide room above the receiver so that the antenna can be installed straight up. If this is not possible,

tilt the RF Antenna at about a 30° angle.

3. Place the RF antenna outside the entertainment center by using a coaxial cable to connect the antenna

to the Hydra HD.

4. Try moving the Hydra HD to other locations.

Page 34

Hydra HD – B Series User’s Guide

REMOTE CONTROL REGISTRATION

You must install the RF remote control antenna before doing the registration.

1. Press and hold the “OK” button on the Hydra front panel for approx. 5 seconds. When releasing the

“OK” button, the Hydra front panel will display “RC REG”. The Hydra is now in remote registration mode.

Figure 10-4 Hydra in Remote Registration Mode

2. On the URC PLUS, press and hold the “STB” button for approx. 5 seconds. The “STB” button backlight

will illuminate.

Figure 10-5 URC PLUS in Remote Registration Mode – Step 1

On the URC PLUS, press “STB” once again. Both the “STB” and “AUX” button backlight will illuminate.

Figure 10-6 URC PLUS in Remote Registration Mode – Step 2

Figure 10-7 URC PLUS in Remote Registration Mode – Step 3

Now the URC PLUS is in registration mode.

Page 35

Hydra HD – B Series User’s Guide

3. Select the decoder to register by:



Press “1” to register URC PLUS to decoder 1.



Press “2” to register URC PLUS to decoder 2.



Press “3” to register URC PLUS to decoder 3.

After you enter a registration event, the “STB” button backlight on the URC PLUS will blink twice to indicate that the registration process was successful.

The Hydra HD front panel will display “RC REG Dx” to indicate that the registration process was successful.

Figure 10-8 Remote Registration Successful

Pressing a key other than “0”, “1”, “2”, “3” or a button is not pressed within 10 seconds, the “STB” backlight will extinguish and the URC PLUS registration process will be terminated.

4. If the Hydra HD does not receive any URC PLUS registration event within 30 seconds, the process will

be terminated.

The Hydra HD front panel displays the following messages during remote control registration:

Table 10-1 Remote Registration Messages

Front Panel Message Description

RC REG TO Registration times out RC REGERR Registration error RC REG In registration mode RC REGEND Registered to IR only mode RC REG D1 Registered to decoder 1 RC REG D2 Registered to decoder 2 RC REG D3 Registered to decoder 3

Here are some principles of the remote registration method:



Each decoder allows a maximum of 3 remote controls to be registered and a registration list is maintained. If the user has registered 3 remote controls and tries to register another remote control, the first registered remote control will be removed from the registration list. This works as a first-in-first-out fashion.



Each remote control can only be registered for one decoder. If user tries to register a remote control which is already registered to another decoder, that remote registration will be removed from the original registration list.



The registration list is maintained in order. If the secondly registered remote control is removed from the list, the third entry will move forth to the second and the third will be blank for a new remote control to be registered.

Page 36

Hydra HD – B Series User’s Guide

CONTROLLING YOUR TELEVISION AND OTHER A/V DEVICES

The Hydra HD remote controls can also be used to control TVs and other A/V devices such as DVD players and recorders. The remote controls use infrared (IR) light signals to control other devices that the remote is programmed to control. IR signals travel only short distances (40 feet or less), and cannot go through walls or other solid objects. You must point the remote control directly at these devices, with no objects blocking the line of sight.

Figure 10-9 Controlling Devices using IR Remote Control

For details of how to program the Hydra remote controls and the supported devices, please refer to the Hydra HD Quick Reference Guide or URC PLUS User’s Guide.

Page 37

Chapter

11.1 Closed Captioning

The Hydra HD supports closed captioning. You can control captioning on decoder 1, 2 and 3 separately. To inquire closed captioning support of TV programs, please refer to your TV service provider.

Closed captioning on decoder 1 is controlled by the Hydra HD. To turn on or off closed captioning on decoder 1, press the “LANG” button on the remote control. The “LANG” button will toggle captioning on and off alternatively. For decoder 1, you cannot control the captioning through your TV.

Figure 11-1Controlling Decoder 1 Closed Captioning

NOTE: Captioning on “TV OUT”, “MATV OUT”, HDMI, Component, S-Video, Composite outputs of decoder 1 is toggled on or off at the same time.

Closed captioning on decoder 2 and 3 are controlled by the TVs. Your TV must have closed captioning feature in order to display captioning. Refer to your TV owner’s manual for details of captioning support and operation control of captioning.

NOTE: Control of captioning may vary for different service providers. For detailed usage of captioning, please refer to the service provider.

Page 38

Chapter

12.1 Aspect Ratio

Hydra HD supports display of both standard definition content which is traditionally filmed in 4:3 aspect ratio and high definition content filmed in 16:9 aspect ratio to both 4:3 or 16:9 TV.

Setting of aspect ratio is provided by middleware. Please refer to your service provider for options available and detailed operation. Typically, aspect ratio is provided in following 3 modes:

1) Mode 4:3 - You choose this mode when your TV is a traditional 4:3 TV.

4:3 Content 16:9 Content

4:3 TV Normal

Left and Right are cropped

2) Mode 4:3 Letter Box (4:3 LB) - You choose this mode when your TV is a traditional 4:3 TV.

4:3 Content 16:9 Content

4:3 TV

Normal

Letter Box with black bar on top and

bottom

3) Mode 16:9 - You choose this mode when your TV is a 16:9 TV.

4:3 Content 16:9 Content

16:9 TV Panorama – Stretched

Normal

Page 39

Chapter

13.1 User Menu

The Hydra HD User Menu is an on-screen setup menu to set up your Hydra HD features. You need to connect the TV properly before using the User Menu.

Each decoder has its own User Menu. The User Menu provides the following setup features:

Table 13-1 User Menu Features

Decoder 1 Decoder 2 Decoder 3

TV 1 Channel ID

 CATV Channel ID

N/A N/A

TV 2 Channel ID

 CATV Channel ID

N/A N/A

TV 3 Channel ID

 CATV Channel ID

N/A N/A

Resolution

 1080i  720p  480p  480i

N/A N/A

Closed Captioning

 Enable  Disable

N/A N/A

Fan Speed

 High  Middle  Low  Off

N/A N/A

HPNA Mode

 Coax  Phone

N/A N/A

TiVo IR Key Code

 MAGNAVOX

10224-B

 CENTURION

00092-B

N/A N/A

NOTE: The features available in User Menu may vary in different middleware. Some of the features can also be set up through the user menu of the middleware.

Page 40

Hydra HD – B Series User’s Guide

USING USER MENU

To start the User Menu:

1. Use the corresponding remote control of the decoder.

2. Press “INPUT” and then “MENU” in sequence within 1 second.

Figure 13-1 Triggering the User Menu

Figure 13-2 Decoder 1 User Menu

Figure 12-3 Decoder 2, 3 User Menu

Page 41

Hydra HD – B Series User’s Guide

To set up a feature:

1. Use remote control “UP” and “DOWN” arrow to select the feature you want to set. The selected feature

will be highlighted by a red rectangle.

2. Press “OK”, the feature will be highlighted in navy blue color.

Figure 13-4 User Menu - Feature in Focus

Figure 13-5 User Menu - Feature selected for choice selection

3. Use remote control “UP” and “DOWN” arrow to loop through available choices.

4. Press “OK’ again when your choice is selected.

5. If you have other features to set up, repeat the above procedures.

Page 42

Hydra HD – B Series User’s Guide

To save your setup or exit:

1. If you have made any setup and want to save the settings, select “SUBMIT” in the User Menu. You will

be notified the saving of your settings.

Figure 13-6 User Menu - SUBMIT highlighted for saving changes

Figure 13-7 User Menu - Changes successfully saved

2. Select “EXIT” to quit the User Menu.

Page 43

Hydra HD – B Series User’s Guide

Figure 13-8 User Menu – Exit User Menu

ATTENTION: If you exit the User Menu without doing the “SUBMIT”, your changes will be lost and will not take effect.

NOTE: If you want to give up the changes, simply select “EXIT”.

Page 44

Hydra HD – B Series User’s Guide

SETTING CHANNEL ID

In “TV OUT”, decoder 1 by default is set to channel 10. In “MATV OUT”, decoder 1, 2 and 3 by default are set to channel 10, 23 and 39 respectively.

You can change the channel ID used by decoder 1, 2 or 3 by using the decoder 1 User Menu.

Follow procedures in section Using User Menu, to make the changes.

NOTE:



Decoder 1 channel ID in “TV OUT” and “MATV OUT” cannot be set separately. They can only be set together.



You can only set the channel ID by using decoder 1 User Menu.



The new channel ID will only take effect after rebooting the Hydra HD.



Do not set decoders to use the same channel ID.



It is recommended to use channel IDs farther apart for the 3 decoders to minimize inter-modulation interference. For example, do not use consecutive channel ID 10, 11 and 12 for decoder 1, 2 and 3. Use channel ID 10, 23 and 39 instead.

SETTING HDMI AND COMPONENT OUTPUT RESOLUTION

You can use decoder 1 User Menu to set the HDMI and Component output resolution. You can also use the Hydra HD front panel “UP” arrow to set the resolution. The setting made in both ways is the same.

To use User Menu to set the output resolution, follow procedures in section Using User Menu, to make the changes.

Please refer to section Setting HDMI and Component Output Resolution for details of setting resolution.

SETTING CLOSED CAPTIONING

You can use decoder 1 User Menu to control decoder 1 closed captioning. You can also use remote control “LANG” button to control decoder 1 closed captioning. The setting made in both ways is the same.

To use User Menu to set closed captioning for decoder 1, follow procedures in section Using User Menu, to make the changes.

Please refer to section Closed Captioning for details of controlling closed captioning.

SETTING FAN SPEED

You can use decoder 1 User Menu to control the fan speed or turn off the fan at all. 3 fan speeds; high, middle and low are provided. You can control the fan speed with fan noise level which is acceptable to you. To ensure good heat dissipation, it is not recommended to turn off the fan.

Follow procedures in section Using User Menu, to make the changes.

Page 45

Hydra HD – B Series User’s Guide

SETTING HPNA

HomePNA is a relatively new technology, which allows you to network your home computers much like a LAN using your existing coaxial or telephone wiring. The Hydra HD is also equipped with HomePNA capability. You can use coaxial or telephone wiring to connect your Hydra HD to your home network. For detailed availability, setup and usage of HomePNA, please refer to your network and TV service provider.

You can select to use telephone wire or coaxial cable for HomePNA network access. Follow procedures in section Using User Menu, to make the selection.

SETTING TIVO IR KEYCODE

Hydra HD is equipped with an IR receiver at the front panel. If you have TiVo or Sling box, you can use the IR blaster provided by TiVo or Sling to control Hydra HD for actions such as channel switching for recording or remote network viewing.

Hydra HD has implemented the following 2 IR keycodes. You can configure TiVo or Sling, and your Hydra HD to use the same keycode in order to complete the setup.

 MAGNAVOX 10224-B  CENTURION 00092-B

Follow procedures in section Using User Menu, to make your IR keycode selection in Hydra HD.

Please refer to the TiVo or Sling user’s manual for configuration and setup of the TiVo and Sling box keycode.

Page 46

Chapter

14.1 Specifications

Main components

Decoders 3 decoders per box

3 decoding and middleware running concurrently Main CPU 300MHz MIPS (per decoder) Memory 256MB SDRAM, 62MB Flash (per decoder) Software Real-time, multi-threaded embedded OS, Java Virtual Machine with

MHP APIs, HTML 4 compliant browser with JavaScript RF Universal Remote Control

3 remote controls come with the box

Additional units can be purchased separately

Max 3 remote controls per decoder

IR carrier frequency is 36KHz using RC6 protocol

Graphics

Color True-color OSD support (up to 1920x1080 pixels)

Programmable OSD scaler, flicker filter

Alpha blending over video (8-bit)

Picture in graphics with scaling

2-D graphic accelerator

Audio and video

Video Input Formats MPEG-1, MPEG-2 MP@HL

MPEG-4.2 ASP@L5

MPEG-4.10 BP@L3, MP@L4.0 and HP@L4.0. Video Output Formats NTSC/PAL composite, S-video and analog YpbPr component with

optional Macrovision v7.1 L1 protection

SDTV or HDTV resolution (1080i60, 720p60, 480p60, 480i60) Audio Input Formats MPEG-1 Layers I & II mono, stereo, joint stereo and dual channel

MPEG-2 5.1; Dolby digital 5.1 channel AC-3 6-channel Audio Output Formats Dolby Digital 5.1 channel AC-3 6-channel PCM and S/PDIF (IEC-

1937/IEC-958)

Dolby Digital or MPEG-2 5.1 down mixed to Dolby Prologic or 2-channel

PCM Analog stereo Closed Captioning CEA-608, EIA-708

Captioning format – ATSC, SCTE and Divicom Connectors 1 x RF TV OUT type-F connector for 1 modulated channel

1 x RF MATV OUT type-F connector for 3 modulated channels

1 x RCA composite video output

1 x RCA composite audio output

1 x S-Video output

1 x YpbPr Component output

1 x HDMI (HDMI 1.1)

1 x S/PDIF digital coaxial audio RCA output

1 x S/PDIF digital optical audio TOSLINK output

1 x RF remote control antenna type-F connector Tuner Optional ATSC/DVB-T tuner

Network interfaces

Page 47

Hydra HD – B Series User’s Guide

Ethernet Ethernet (10/100Base-T auto-sensing) Caller ID Bell 202 and ITU-T V.23 FSK Demod, Bellcore GR-30-CORE & SR-

TSV-002476

(CND, CNAM, VMWI, CIDCW) Home networking Optional HPNA 3.0 (Telephone wire / Coaxial Cable)

Physical and

mechanical

Dimensions 350 x 50 x 310mm (WxHxD) Weight 1.5 kg Operating voltage 100-240VAC RMS Operating current 1.5A RMS, max. Operating frequency Range ~47-63Hz Output voltage 12V/2A; 5.2V/5A Operating temperature 10° to 35° C (50° to 95° F) Relative Humidity non-condensing Regulatory compliance UL, CE, IEC65, FCC part 15 (pending) Security controls Anti-Taping Macrovision (optional) Parental Controls Provided through middleware partner integration

NOTE: Above specification for reference only.

Page 48

Chapter

15.1 Troubleshooting the Hydra

This section describes some of the most common problems that might be encountered when installing Hydra HD, and the solutions to those problems.

Symptom Remedy Reference

Remote controls do not work

• Check batteries are correctly loaded.

• Check that new URC PLUS remote control is

used.

• Check remote control is registered. In case of doubt, register the remote control again.

• You may be experiencing interference from objects near the remote control antenna. Follow instruction in section 9.3 for improvements.

Section 10 – Remote

Controls

Remote controls cannot control the programmed devices

• Device manufacturers may change their device codes or no device code can be found in the Universal Remote Control User’s Guide. Try searching the device code according to the procedures listed in the Universal Remote Control User’s Guide.

Hydra HD Quick Reference Guide Universal Remote Control User’s Guide

Standby indicator at the front panel not lit

The power supply to the box is probably not

working:

• Check that the AC/DC adapter is connected properly to the DC INPUT connector.

• Check that there is power from the power source.

• Make sure you have pressed the Standby button at the top of the box and that the Standby / On light is green.

Section 9 – Powering up

Hydra

Standby indicator on the front panel stays orange for more than 60 seconds

• Check that the ADSL cable is properly connected between the ADSL connector and the ADSL modem. The ADSL Link indicator should be orange and steady.

• Check that the ADSL modem is properly connected to the telephone socket.

Section 7 – Powering up

Hydra

Standby indicator turns green; no picture on the primary TV

• Check that the video output connector of the Hydra HD is properly connected to the input connector of the primary TV.

• “TV OUT” or “MATV OUT” (coaxial connection): the TV set should be set to channel 10.

• Composite, S-VIDEO, Component or HDMI connection: the TV set should be set to the correct input mode for the signal.

• Component or HDMI connection: the resolution selected in Hydra HD is supported

Section 4 – Connecting

the Primary TV

Page 49

Hydra HD – B Series User’s Guide

by your TV.

Picture shows on the primary TV but not any other TV

• Check that the RF cable is properly connected between the “MATV OUT” and the main video source socket.

• Check that the TV is set to the proper channel (10, 23, or 39) and in CATV mode.

Section 5 – Connecting

TV(s) in Another Room(s)

No sound

• Check that the audio cable is connected to the correct input in your device.

• Is the volume of the device turned down to the minimum level?

• If HDMI or component is used. Try disabling AC-3.

• If HDMI is used, check the resolution and try to use the composite audio output.

Section 6 – Connecting

to Audio System

Multi-channel sound not working

• Check with service provider that programs contain multi-channel AC-3 signal.

• Check that AC-3 is enabled in the Hydra HD.

• Check your TV or A/V equipment for AC-3

multi-channel setup.

Section 6 – Connecting

to Audio System

No sound, poor sound or popping noise on HDMI

• HDMI is an evolving technology, so it is possible that some TVs may not operate properly with Hydra HD. In case of problem, use component video output and composite audio output to connect your primary TV.

Section 4 – Connecting

the Primary TV

Entone Hydra HD – B Serie, Hydra HD – Serie User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual