EnOcean PTM 535, PTM 535U, PTM 535J User Manual

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

Patent protected:

WO98/36395, DE 100 25 561, DE 101 50 128, WO 2004/051591, DE 103 01 678 A1, DE 10309334, WO 04/109236, WO 05/096482, WO 02/095707, US 6,747,573, US 7,019,241

Observe precautions! Electrostatic sensitive devices!

PTM 535 / PTM 535U / PTM 535J

EnOcean Transmitter Module

21.09.2020

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

REVISION HISTORY

The following major modifications and improvements have been made to this document:

Version

Author

Reviewer

Date

Major Changes

1.0

MKA

23 May 2018

Initial Release

1.1

MK/CB

CB

02 Aug 2018

Configuration set and functional block diagram updated, additional minor changes e.g. ARIB ID added, Tx range free field 300m

1.2

MK/CB

CB

14 Sep 2018

Renamed Pad 13 from VCC to VCC_MODE, V+ for configuration only, hint for PTM Config help

1.3

MK/CB

CB

21 Nov 2018

4.4 added strict sequence and tool requirements for configuration change,

2.3 added CFG test pin

1.4

MK/CB

CB

27 May 2019

Document branding changed, 2.2 pin out image corrected

1.5

MKA

21 Sep 2020

FCC / ISED added

Published by EnOcean GmbH, Kolpingring 18a, 82041 Oberhaching, Germany www.enocean.com, info@enocean.com, phone +49 (89) 6734 6890

Important!

This information describes the type of component and shall not be considered as assured characteristics. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For the latest product specifications, refer to the EnOcean website: http://www.enocean.com. As far as patents or other rights of third parties are concerned, liability is only assumed for modules, not for the described applications, processes and circuits. EnOcean does not assume responsibility for use of modules described and limits its liability to the replacement of modules determined to be defective due to workmanship. Devices or systems containing RF components must meet the essential requirements of the local legal authorities. The modules must not be used in any relation with equipment that supports, directly or indirectly, human health or life or with applications that can result in danger for people, animals or real value. Components of the modules are considered and should be disposed of as hazardous waste. Local government regulations are to be observed. Packing: Please use the recycling operators known to you.

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

TABLE OF CONTENT

1 General description ........................................................................................ 5

1.1 Product description ........................................................................................ 5

1.2 Product variants ............................................................................................ 5

1.3 Technical data ............................................................................................... 6

1.4 Maximum ratings for input signals ................................................................... 6

1.5 Physical dimensions ....................................................................................... 6

1.6 Device drawing ............................................................................................. 7

1.7 Environmental conditions ............................................................................... 8

1.8 Ordering information ..................................................................................... 8

2 Functional description .................................................................................... 9

2.1 Functional Principle ........................................................................................ 9

2.2 Block diagram ............................................................................................... 9

2.3 Interface pin layout ..................................................................................... 10

2.4 Interface pin functionality ............................................................................. 11

3 Radio telegram format ................................................................................. 12

3.1 Standard mode ........................................................................................... 12

3.2 Enhanced security mode .............................................................................. 14

3.3 Switching between operation modes .............................................................. 15

3.4 Transmission timing ..................................................................................... 15

4 PTM 535 configuration ................................................................................. 16

4.1 PTM 535 configuration parameters ................................................................ 16

4.2 PTM 535 configuration interface .................................................................... 17

4.3 PTM 535 test point location ........................................................................... 17

4.4 Connection between Segger J-Link and PTM 535 ............................................. 18

4.4.1 Segger power supply (6-Pin interface) .................................................... 18

4.4.2 External power supply (4 pin configuration interface) ............................... 19

4.5 Required tools ............................................................................................. 20

4.6 Configuration setup ..................................................................................... 21

4.7 User Interface ............................................................................................. 21

4.8 Execution sequence ..................................................................................... 22

5 Application information ................................................................................ 23

5.1 Connection to ECO 200 energy harvester ....................................................... 23

5.2 How to populate a teach-in button (for enhanced security mode) ...................... 23

5.3 Antenna specification ................................................................................... 24

5.4 Layout recommendations ............................................................................. 25

5.5 Transmission range ..................................................................................... 26

6 Regulatory information ................................................................................. 27

6.1 RED (European Union) ................................................................................. 27

6.2 FCC (United States) ..................................................................................... 28

6.2.1 FCC grant of equipment authorization .................................................... 28

6.2.2 FCC regulatory statement ..................................................................... 29

6.3 ISED (Canada) ............................................................................................ 30

6.3.1 ISED technical acceptance certificate...................................................... 30

6.3.2 ISED regulatory statement .................................................................... 32

6.3.2.1 English version ................................................................................. 32

6.3.2.2 French version .................................................................................. 33

6.4 ARIB (Japan) .............................................................................................. 34

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

6.4.1 ARIB (Japan) certificate ........................................................................ 34

6.4.2 ARIB (Japan) regulatory requirements .................................................... 35

7 Product history ............................................................................................ 36

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1 General description

1.1 Product description

The radio transmitter module PTM 535, PTM 535U and PTM 535J from EnOcean enable the implementation of wireless sensors and switches without batteries.

Key applications are handheld remote controls or industrial switches.

1.2 Product variants

The following product variants are offered:

◼ PTM 535

Operating frequency 868.300 MHz

◼ PTM 535U

Operating frequency 902.875 MHz

◼ PTM 535J

Operating frequency 928.350 MHz

All three variants contain a pre-installed whip antenna, support enhanced security and are delivery in a cardboard box. The term “PTM 535” is subsequently used to describe all three product variants unless otherwise noted.

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1.3 Technical data

Power supply ECO 200 or equivalent energy pulse

Antenna Pre-installed whip antenna

Frequency / Modulation / Transmission power PTM 535 868.300 MHz / ASK / +5 dBm PTM 535U 902.875 MHz / FSK / +4 dBm PTM 535J 928.350 MHz / FSK / +0 dBm

Data rate 125 kbps

Telegram type RPS Type 2

SEC (Encrypted and authenticated transmission)

Digital inputs 4 (2 of those also usable via meander contacts)

Mode selection (standard / enhanced security) 3 pins / LRN Button

Transmission range up to 300 m free field, up to 30 m indoor

1.4 Maximum ratings for input signals

Symbol

Parameter

Min

Max

Units

AC1, AC2

Supply voltage operation

0

6.0

V

V+

Supply voltage configuration

0

5.5

V

GND

Voltage on GND pin

0 0 V

A0, A1, B0, B1, SECURE, STANDARD, CFG

Voltage on digital input pins

0

3.6

V

1.5 Physical dimensions

PCB dimensions 26.2 x 21.15 x 3.5 mm

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1.6 Device drawing

Figure 1 – PTM 535 outline

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

1.7 Environmental conditions

Operating temperature -25 °C … +65 °C

Storage temperature -40 °C … +85 °C

Storage temperature in Tape & Reel -20 °C … +50 °C

Humidity 0% … 93% r.h., non-condensing

1.8 Ordering information

Type

Ordering Code

Frequency

Note

PTM 535

S3001-A535

868.300 MHz

Whip antenna, Delivered in cardboard box

PTM 535U

S3051-A535

902.875 MHz

Whip antenna, Delivered in cardboard box

PTM 535J

S3061-A535

928.350 MHz

Whip antenna, Delivered in cardboard box

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

2 Functional description

2.1 Functional Principle

PTM 535 is designed to be powered by an ECO 200 kinetic energy harvester from EnOcean. PTM 535 can be mechanically connected to the contact springs of ECO 200 by means of its integrated PCB contacts.

PTM 535 provides 4 digital input pads and two PCB meander structures allowing the implementation of push button functions either via external connection or via conductive rubber pads.

When the ECO 200 harvester generates an energy pulse or when power is supplied by another source then PTM 535 determines the polarity of the energy pulse (push or release direction), and the operating status of the digital inputs and encodes this information in an RF telegram.

The communication mode (enhanced security communication or standard communication) can be selected using the SECURE and STANDARD input pins or the LRN button (which is not mounted by default). Default communication mode is STANDARD.

2.2 Block diagram

Figure 2 below shows the block diagram of PTM 535.

Figure 2 – PTM 535 functional block diagram

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

2.3 Interface pin layout

Figure 3 below shows the pin out and external interfaces of PTM 535 as seen from the top (component side). Items marked in green are on the component side while items in grey are on the bottom side.

In addition to the 16 boundary contacts, PTM 535 provides the following contact points:

◼ Meander contact A0

◼ Meander contact A1

◼ Connection for whip antenna RF_WHIP

◼ Footprint for LEARN button (connecting VCC and SEC)

◼ AC1 / AC2 power supply connection to ECO 200 harvester

(two contact pairs at the PCB bottom side to support different ECO 200 orientation)

Figure 3 – PTM 535 pin-out and external interfaces

USER MANUAL

PTM 535 / PTM 535U / PTM 535J – ENOCEAN TRANSMITTER MODULE

2.4 Interface pin functionality

Table 1 below describes the PTM 535 interface pin functionality.

Function

Characteristics

GND

Ground connection

Must be connected to GND

VCC_MODE

Internal Operating voltage with 1k

Connect externally to SECURE or STANDARD pin to change operation mode. Also connected to LEARN button pad.

SECURE

Mode change pin

Connect this pin to VCC_MODE and press the ECO 200 harvester to change operation mode to enhanced security. Then disconnect. Also connected to LEARN button footprint.

STANDARD

Mode change pin

Connect this pin to VCC_MODE and press the ECO 200 harvester to change operation mode to standard. Then disconnect.

B0

O-Button Rocker B

Digital input, leave open or connect to GND Internal pull-up

B1

I-Button Rocker B

Digital input, leave open or connect to GND Internal pull-up

A0

O-Button Rocker A

Digital input, leave open or connect to GND Internal pull-up, Connected to meander contact

A1

I-Button Rocker A

Digital input, leave open or connect to GND Internal pull-up, Connected to meander contact

AC1

ECO 200 Input 1

ECO 200 or equivalent energy pulse

AC2

ECO 200 Input 2

ECO 200 or equivalent energy pulse

RF_WHIP

RF output

Output for whip antenna

RF_50

RF output

50 Ohm output for external antenna

CFG

Test pin

Do not connect

Table 1 – PTM 535 interface pin functionality

EnOcean PTM 535, PTM 535U, PTM 535J User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1 General description

1.1 Product description

1.2 Product variants

1.3 Technical data

1.4 Maximum ratings for input signals

1.5 Physical dimensions

1.6 Device drawing

1.7 Environmental conditions

1.8 Ordering information

2 Functional description

2.1 Functional Principle

2.2 Block diagram

2.3 Interface pin layout

2.4 Interface pin functionality