LT0003400A20000000
Door Switch Sensor
Installation Guide
Enlogic Door Switch Sensor
SKU: EA9109
The Critical Component
Enlogic’s Door Switch Sensor is designed to send an alarm or notification signal
when the door on which is installed had been opened more than 10mm. This
provides added security. You can extend the length of the sensor cable up to 30.5
m (100 ft) using the RJ-45 coupling and standard CAT-5 cabling.
Note: The Enlogic Door Switch Sensor is only designed to connect to an Enlogic PDU or Inline
Energy Meter. Connecting it to another device may result in damage.
www.enlogic.com
LT-00034-A4
Inventory
Door Switch Sensor Assembly
RJ45 Quick Disconnect
Coupler
Tap Screw
(quantity: 4)
Adhesive Backed Mount
(quantity: 5)
Standard Ethernet Extension Cable
1.8m in length
Double-sided Tape
(quantity: 2)
Cable Ties
(quantity: 5)
Installation Instructions
Top Door Mounting Option
1. Attach the Door Switch Assembly to the top of the rack using the adhesive backed mount and cable
ties.
2. Attach the Switch Sensor to the top corner of the rack (on the side that the rack door will close) using
double-sided tape. Secure the cable to the top of the rack using cable ties.
3. Attach the Magnetic Sensor to the rack door using double-sided tape.
4. Thread the sensor connection cable through the rack. Secure the cable with cable ties. Plug the cable
into a sensor port on the PDU.
Door Switch Assembly
Magnetic Sensor
5. Log into the Web Interface, Telnet, or Serial to manage the Door Sensor alarm and notification
settings. The sensor is designed to alarm if the door is opened more than 10mm.
Switch Sensor
Connection cable
plugged into PDU
Inside Door Mounting Option
1. Attach the Door Switch Assembly to the top of the rack using the adhesive backed mount and cable
ties.
2. Attach the Switch Sensor to the inside of the rack (on the side that the rack door will close) using 4
screws (FS00041). Secure the cable to the top of the rack using cable ties.
3. Attach the Magnetic Sensor to the rack door using screws.
4. Thread the sensor connection cable through the rack. Secure the cable with cable ties. Plug the cable
into a sensor port on the PDU.
5. Log into the Web Interface, Telnet, or Serial to manage the Door Sensor alarm and notification
settings. The sensor is designed to alarm if the door is opened more than 10mm.
The Enlogic Door Switch Sensor is now installed and ready to use. For more information, contact your
regional sales oce or go to www.enlogic.com.
Door Mounting Option
1. Attach the Door Switch Assembly to the top of a door jamb using the adhesive backed mount and
cable ties.
2. Attach the Switch Sensor to the door (on the side that the rack door will close) using the 4 screws
(FS00041). Secure the cable to the top of the rack using cable ties.
3. Attach the Magnetic Sensor to the rack door using screws. (See below.)
4. Thread the sensor connection cable through the rack. Secure the cable with cable ties. Plug the cable
into a sensor port on the PDU.
5. Log into the Web Interface, Telnet, or Serial to manage the Door Sensor alarm and notification
settings. The sensor is designed to alarm if the door is opened more than 10mm.
The Enlogic Door Switch Sensor is now installed and ready to use. For more information, contact your
regional sales oce or go to www.enlogic.com.
Installation Notes:
• APC Rack models can only use the Door Switch Sensor in the top-mounted orientation.
• The top-mounted orientation is more reliable than the door-mounted orientation.
• The cable for the Door Switch Sensor can be extended using RJ45 coupling.
Enlogic Systems, LLC
Wildwood
Missouri 63040 United States
sales@amer.enlogic.com
Enlogic Systems Europe, Ltd.
Worcester
United Kingdom WR1 2PG
sales@emea.enlogic.com
Enlogic Systems Asia Pacic, Ltd.
Tsim Sha Tsui
Kowloon, Hong Kong
sales@apac.enlogic.com
Loading...