enlighted GW-2-01 Installation Instructions Manual

Page 5 Page 6

Page 1

Copyright© 2015 Enlighted Inc. All rights reserved.

All other brandor product names are trademarks of

their respective companies or organizations.

TechnicalSupport

For questions regarding the installation or operation of
this product, contact Enlighted

Technical Support: [e-mail]

Company Contact Information

Location: 930 Benecia Ave, Sunnyvale, CA 94085
Phone: [phone]
Web: enlightedinc.com

FCC and Canada Compliance Information

This device complies with Part 15 of the FCC Rules and with Industry
Canada license-exempt RSS standards. Operation is subject to the
following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept a ny int er f er en c e received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by Enlighted Inc. c ould void the user's
authority to operate the equipment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,
et (2) l'utilisateurde l'appareil doitaccepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.

Under Industry Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to
other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communicat ion.

Conformément à la réglementation d'Industrie Canada, le présentémetteur radio
peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur)
approuvé pour l'émetteur par Industrie Canada. Dans le but de réduireles risquesde
brouillage radioélectriqueà l'intention des autres utilisateurs, il faut choisirle type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépassepas l'intensité nécessaireà l'établissementd'une communication
satisfaisante.

This radio transmitter IC: 10138A-GW2 has been approved by Industry
Canada to operate with the antenna types listed below with the maximum
permissible gain and required antenna impedance for each antenna type
indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for
use with this device.

Le présent émetteur radio IC: 10138A-GW2 a été approuvépar Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible
maximal et l'impédancerequise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont
strictement interdits pour l'exploitation de l'émetteur.

CE

This device complies with the essential requirements and other relevant
requirements of the R&TTE Directive (1999/5/EC). The product is compliant
with the following standards and/or other normative documents -EN 62479,
ETSI EN 301 489-1-17, EN 300 328 and EN 60950-1

•The equipment is Class 1 radio equipment which can be placed on the
market and be put into service without restrictions in accordance with
article 1(3) of Commission Decision 2000/299/EC (Version July 2014).

Gateway (GW)

Model GW-2-01

Installation Instructions

Figure 1: Gateway Unit (front and back)

Shipped Components

• Enlighted Gateway

• Two #6 - 1” screws with standoffs

• Antenna: Nearson S151AH-07826 2.4GHz Swivel

Antenna with 5dBi, 50 Ohm

Tools You May Need

• #2 Philips screwdriver

Supplies You May Need

• Cat-5e or Cat-6 data cable with RJ45 (conforming to
TIA/EIA 568-B) connectors between the gateway
(GW) and PoEEthernet switch

Model: GW-2-01
FCC ID: AQQ-GW2
IC: 10138A-GW2

93-01246-01-01 Rev04 081215

Page 2

Page 3

Page 4

Caution

• Disconnect all power before installationor service.

• Installationandmaintenancemustbeperformedbya qualified

electricianinaccordancewithlocal, state,and national electrical
codes (NEC) and requirements.

Problem Solution

No LED on the
Gateway (GW) is
on or blinking.

• Verify the Cat-6 cable

between the PoE port on
the Ethernet switch and
the Enlighted Gateway
has not been damaged.

• Check that the RJ45

connectors on each end
of the Cat-6 cable are
completely inserted.

• Verify that the PoE

Ethernet switch is powered
and functioning properly.

Red LED on the GW
is on continuously.

Replace the Gateway.

Red LED on the
GW is blinking at
a slow rate and
the green LED is
off.

This is the expected blink
pattern before the
Energy Manager is
connected to the PoE
Ethernet Switch and
made operational.

Red LED on the GW
is off and the green
LED is blinking
rapidly.

This is the expected blink
pattern after the Energy
Manager is connected to
the PoE Ethernet Switch
and made operational,
and before the GW is
commissioned.

Troubleshooting

Figure 2: Attach the unit to the wall on screws

with the antenna pointing up

Figure 4: Wiring Diagram for PoE switch and GW

Step Description

1

Determine a location for the GW. The Cat-5e
or Cat-6 data cable from the PoE Ethernet
switch MUST be less than 300 feet. Ideally, the
GW will be at the same elevation as the
sensors it communicates with. It MUST be
visible so that it’s LEDs can be seen for
troubleshooting. Because it uses wireless
communication with sensors, it SHOULD be
placed to maximize the number of sensors
that are near it.

2

Select a location for the RJ45 connector
(conforming to TIA/EIA 568-B) of the data
cable to exit the wall or ceiling. Make a small
circular cut (roughly 11/16

th

of an inch in
diameter) in the wall or ceiling for the RJ45
connector.

3 Install the two #6, 1” screws two inches apart.
4 Slide the GW onto the screwsas shown in

Figures 2 and 3.

5 If on the wall, point the antenna straight up.

If on the ceiling, point antenna straight down.

6 Insert the RJ45 connector on one end of the

data cable into the GW.

7 Route the data cable to the PoE Ethernet

switch and insert the RJ45 connector into a
powered PoE port (see Figure 4).

8 Power on the PoE Ethernet switch and check

for the “PoE Active” LED to be green for the
port connecting the GW.

Installation Steps (both wall & ceiling mounts)

Note: After a Gateway has been commissioned, the red
LED is off and the green LED blinks at a slow rate.

Figure 3: Attach the unit to the ceiling on screws

with the antenna pointing down

PoE Active

LEDs