Engineered Comfort CTE-5201W16 Operation And Users Instructions

OPERATION AND USERS INSTRUCTIONS
ACN ANALOG THERMOSTAT (CTE-5201)
FAN COIL UNITS

Model CTE-5201W16 Thermostat:

Model CTE-5201-16 (LCD analog thermostat) (Figure 2) - single
output with limits, PI function is designed to be used with the
CEE-5201 Fan Coil Unit controller (Figure 1). Model CTE-5201-16
Thermostat comes with the following factory default settings:

Set Point (Default): 70°F
MAX: 100%
MIN: 20%
F/C Mode: Degrees F
UNOCC Mode: OFF
PROP: 4ºF

NT: 30 Minutes

I

To change any one of these values, except the F/C Mode, first
push the button to display the value to be changed. Use the Up /
Down buttons to change the value. Then hold down the
corresponding button for approximately 10 seconds until the display
begins to flash. The new value has now been written into memory.

To change to degrees C mode simply press and hold the F/C
button down for 10 seconds until the display begins to flash. To
change back to degrees F repeat the procedure.

Set Point (Normal)

The set point range is 60 – 85°F (15.6 – 29.4°C). To change the
set point, push the SET POINT button to display the current value.
Use the Up / Down buttons to change the value. The display will
time out and revert back to displaying the room temperature and
the thermostat will control to the new set point.

Set Point (Default)

If power is lost, when the unit is powered back up, the set point will
revert to the default value of 70°F (21.1 C). This default value can
be changed to any value in the set point range. This default set
point is also used in the dead band unoccupied mode.

MAX

This is the maximum value that the output can attain. It is
adjustable up to 100% (10 volts) and down to the MIN setting.

MIN

This is the min. value that the output can attain. It is adjustable
down to 0% (0 volts) and up to whatever the MAX is set for.

F/C Mode

The F/C button toggles the display between °F and °C. Room
temperature, set point, proportional band, dead band, and offset
will be displayed in the desired units.

UNOCC

Momentarily pressing this button will put the unit into the
unoccupied mode. It will stay in this mode until either the Set Point
or Up / Down buttons are pushed. There are two unoccupied
modes, OFF or DEADBAND.

OFF UNOCC Mode

The output voltage is forced to 0 volts (0%). A safety override will
bring the output up to 2 volts placing the unit in heating if the room
temperature falls below 50°F. The output will return to 0 volts
when the room temperature reaches 55°F.

DEADBAND UNOCC Mode

In this mode the set point is set to 70°F, the integral action is
disabled, and a dead band of +/- 10°F is set around the set point.
As long as the room temperature is within the dead band the fan

will run at MIN conditions.

PROP

The proportional band is the temperature band around the set
point over which the output will vary from MIN to MAX due to the
proportional action alone. The proportional band is adjustable from

– 6°F (1.1 – 3.3°C).

2

INT

As long as there is a difference between room temperature and
set point, the integral action will cause the output to integrate up
or down. The integral time is the time it takes the integral action to
repeat the effect of the proportional action. The integral time is
adjustable from 15 to 30 minutes. Setting the integral time to 0 will
disable the integral action.

Temperature Offset

By pressing both MIN and INT together it is possible to offset the
internal temperature sensor by +/- 2°F (+/- 1.1°C). After using the
Up / Down buttons to change the offset both the MIN and INT
buttons must be held down together for 10 seconds until the
display begins to flash in order to write the new offset into memory.

Figure 1. CEE-5201 Analog Controller Card

Supply Voltage: 24 VAC +20/-15% 50/50Hz
Supply Power: 1 VA plus output loads
Discharge Temp Input: 10K OHM@25ºC, NTC 4.37% / ºC
Fan Output: Min Adjustable 0–10 VDC

CWV Output: Max adjustable from 0 to 10 VDC
Heat Stage 1 & 2 Outputs: Triac outputs 10VA Max @ 24VAC

Thermostat connector: PIN 1 NC

Connections: Plated screw terminals 14 to 22 AWG Cu

Ambient Limits: Operating 0 to 120ºF (-18 to 49ºC)

Mounting: Open Board / Snaptrack supplied

Stage 1 Max adjustable from Min to 10 VDC
Stage 2 Max adjustable from stage 1 Max to 10VDC

Cooling Max adjustable from Min to 10 VDC

PIN 2 DC COM
PIN 3 Supply Output 16 VDC +/-10% 10mA
PIN 4 Tin 1-10 VDC 100 KOHM
PIN 5 DC COM
PIN 6 NC

RJ-11 thermostat jack

Shipping -40 to 140ºF (-40 to 60ºC)

Engineered Comfort reserves the right to change any information concerning product or specification without notice or obligation.

Page 1 of 22/14/11 EC-IOM-ACN

3

1/8" (79)

5

"

(

127)

7

/8"

(

22)

3

/8"

(

10)

SETPOINTROOM TEMP

VIEW WITH COVER OPENED

S

ET

P

OINT

SET

POINT

DOWN BUTTON

UP BUTTON

SET POINT

BUTTON

MAX F/C PROG

MIN UNOCC INT

ACCESSORIES
HMO-1161W: 4" x 4" wallplate, White

HPO-0044: Replacement allen screws
HSO-5013-50: 50' plenum cable w/conn.
HSO-5013-03: 3' plenum cable w/conn.

T

HERMOSTAT TO BASE
MOUNTING SCREWS (2)
(

1/16" ALLEN SOCKET)
TURN IN TO REMOVE
THERMOSTAT FROM BASE

P

IN1

P

IN6

3 1/4"

(83)

2

4/7"

(65)

ø .15

Figure 2. Model CTE-5201W16 (Fan Coil Unit LCD analog thermostat)

Supply Voltage: 14 -19 VDC
Set Point Range: 60 – 85°F (15.6 – 29.4°C)

(Power On Default: 70°F / 21.1°C)

Temperature Sensor Type: Thermistor
Accuracy: +/- 0.36–F (0.2°C)
Display Degrees F or C: Selectable (Factory Setting: Degrees F)
Direct Acting Output: 0 – 10 VDC
MIN / MAX Limits: Adjustable 0 – 100%

(Factory Settings: MIN=20, MAX =100)

Proportional Band: 2 – 6°F (1.1 – 3.3°C) (Factory Setting: 4°F)
Integration Time: 15 – 60 Minutes (0=OFF)

Unoccupied Setpoint Modes: OFF or Deadband

(Factory Setting: 30)

(Factory Setting: OFF)

OFF Mode: Output Voltage = 0.0 Volts

(Safety Override: Output Cycles 0.0 Volts to

2.0 Volts. To Maintain 50°F to 55°F)

F a n C o i l U n i t s

Deadband Mode: Integral Action Disabled & Set Point.

Temperature Offset: Adjustable +/-2°F (+/- 1.1°C)

Operating Ambient: 34 – 125°F (1.1 – 51.6°C)
Shipping Ambient: -40 – 140°F (-40 – 60°C)
Humidity: 0 – 95% Non Condensing
Case Material: White ABS.

Houston, Texas

Tel: [phone]

Fax: [phone]

Set to Default +/- 10°F Deadband.
Deadband Output Midway between Max &
Min.

(Press MIN & INT together)

UL Frame Class 94HB.
RJ-11 Female Connector.
PIN1 NC PIN2 COM PIN3 SUPPLY
PIN4 OUT PIN5 COM PIN6 NC

Las Vegas, Nevada

Tel: [phone]

Fax: [phone]

www.engineered-comfort.com

Toronto, Canada

Tel: [phone]

Fax: [phone]

2/14/11 EC-IOM-ACNPage 2 of 2

Calgary, Canada

Tel: [phone]

Fax: [phone]