EnGenius DuraFon-SIP User Manual

~2~

Table of Contents

User Manual

DuraFon-SIP System

Durable, Long-Range Cordless Phone

EnGenius Customer Service

http://www.engeniustech.com/

Safety Instructions ........................................................................................ 5

General Safety Instructions ...................................................................... 5

Product Safety Instructions ...................................................................... 5

Battery Safety Instructions ...................................................................... 7

Regulatory Information ................................................................................ 8

Equipment Checklist ................................................................................... 11

Handset Illustration .................................................................................... 12

Basic Handset Features .......................................................................... 13

Additional Handset Features ................................................................. 15

Base Illustration ..................................................................................... 21

Base Features ............................................................................................. 22

Basic Base Station Features ................................................................... 22

Charger Illustration .................................................................................... 23

Charger Features ........................................................................................ 24

Getting Started ........................................................................................... 25

Base Station Installation ........................................................................ 25

Handset and Charger Installation .......................................................... 26

Basic Operations ......................................................................................... 27

Operation Modes ................................................................................... 27

A. Base Operation Modes .................................................................. 27

B. Handset Operation Modes ............................................................ 27

Making a Telephone Call ........................................................................ 29

Making a 2-Way/ Intercom Call ............................................................. 30

Making a Broadcast................................................................................ 30

Handset-to-Handset Calls .................................................................. 30

Redial ..................................................................................................... 31

Receiving a Telephone Call .................................................................... 32

Receiving an Intercom Call ..................................................................... 32

Ending a Call ........................................................................................... 33

Adjusting Handset Receiver (Earpiece) Voice Volume .......................... 33

Adjusting Handset Speakerphone Voice Volume .................................. 33

Placing a Call On Hold ............................................................................ 34

Mute ....................................................................................................... 34

Do Not Disturb (Silent Ring) ................................................................... 34

Key Guard ............................................................................................... 35

Battery Recharge and Replacement ...................................................... 35

~3~

Advanced Operations ................................................................................. 36

~4~

Handset Registration ............................................................................. 36

Handset Group Subscription .................................................................. 37

Call Transfer ........................................................................................... 38

Phonebook Operations .......................................................................... 40

Programmable Feature Call ................................................................... 43

Caller ID .................................................................................................. 45

Call Manager .......................................................................................... 46

Incoming ................................................................................................ 47

Outgoing ................................................................................................ 47

Call Barring ............................................................................................. 48

Visual Message Waiting Indicator (VMWI) ............................................ 49

Adjust Handset Microphone Gain .......................................................... 49

Adjust Headset Ring ............................................................................... 50

SIP Configuration ........................................................................................ 51

Introduction ........................................................................................... 51

Application ............................................................................................. 51

VoIP Features ......................................................................................... 51

Registration Handsets ............................................................................ 51

Default Settings ................................................................................. 52

Web Configuration ............................................................................ 52

LAN Configuration ............................................................................. 53

Base Settings ...................................................................................... 53

Phone Book ........................................................................................ 54

SIP Configuration ................................................................................... 55

SIP Server ........................................................................................... 55

SIP Account ........................................................................................ 56

Individual Account ............................................................................. 56

Group Account ................................................................................... 57

Audio Setting ..................................................................................... 59

Auto-Provision ................................................................................... 59

Tools ....................................................................................................... 60

Admin ................................................................................................ 60

Time ................................................................................................... 61

Ping Test ............................................................................................ 61

Firmware ............................................................................................ 62

Back-up .............................................................................................. 62

Reset/Reboot/Registration ................................................................ 62

Menu Operations ....................................................................................... 64

Technical Specifications ............................................................................. 69

Base Station ................................................................................................ 71

Index ........................................................................................................... 76

~5~

Safety Instructions

~6~

Caution: Your wireless telephone gives you freedom and flexibility to stay in touch while you move around. However, when using your phone equipment, safety instructions should be followed to avoid the risks of fire, electric shock, injury to person, and damage to property.

General Safety Instructions

1. When using your wireless phone, ensure your safety and the safety of others:

a. Always watch where you are walking and standing.

b. Do not let a phone call distract you from working safely.

c. If power goes out, your phone will not work. Backup power is

recommended.

2. In an emergency:

a. If an emergency occurs, dial the emergency phone number. Remember: if

you are in an area where your phone does not have a clear signal from the base, it is highly probable that the call may not go through. Locate the nearest landline telephone or other communications device to call for help.

b. Emergency calls may not automatically provide emergency personnel with

your name, phone number or location.

3. Notice to Hearing Aid Users: This phone system is compatible with inductively

coupled hearing aids.

4. Notice to Cardiac Pacemaker Users: Preliminary studies done by the US FDA

and others have shown that, although interference to the implanted cardiac pacemaker may occur when operating very closely, wireless telephones “do not seem to pose a significant problem for pacemaker wearers.” However, until more is known, the FDA suggests that people with pacemakers may want to take precautions when using or carrying a wireless telephone to ensure that there is ample distance between the telephone and the pacemaker. Do not carry the handset in a breast pocket. If you have any reason to suspect that interference is taking place, turn off your handset immediately.

Product Safety Instructions

1. Read and understand all instructions.

2. Follow all warnings and instructions including those marked on the product.

3. Changes or modifications to this product not expressly approved by the

manufacturer will void the warranty and the FCC authorization to operate the equipment. Use only manufacturer provided accessories.

4. Do not use the telephone near water. Never spill liquid of any kind on this

product.

5. Unplug the product from the wall telephone jack and power outlet before

cleaning. Do not use liquid or aerosol cleaners. Use damp cloth for cleaning.

6. Do not place this product on an unstable cart, stand, or table. The product may

fall and cause personal injury or damage to the product or other property.

7. Power Outage: In the event of a power outage, your handset charger will not

recharge the handset battery, and the base station will not allow you to make an outgoing call or take an incoming call. Both the charger and the base station require electricity for operation. You should have a telephone that does not require electricity available for use during power outages, or have a temporary backup power supply.

8. Slots or openings in the product’s housing are provided for ventilation. These

openings must not be blocked or covered. Placing the product on a bed, carpeting, or other similar surface may block these openings and should be avoided. This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.

9. Never push objects of any kind into this product through housing

slots/openings as they may damage the product, touch dangerous voltage points or short out parts that could result in fire, electric shock, or injury.

10. This product should be operated only from the type of power source indicated

on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

11. Do not overload wall power outlets and extension cords as this may result in

fire or electric shock.

12. To avoid electric shock or burn, do not disassemble this product. Send this

product to an authorized service center when service or repair work is required. Call Customer Service for locations near you. Opening or removing covers may expose you to dangerous voltages, electrical currents or other risks. Incorrect re-assembling of the product may cause electric shock when the product is subsequently used.

13. Avoid using the product during a storm. There may be a risk of electric shock

from lightning.

14. Do not place the product where persons can step, trip, or fall on it.

15. Do not place conductive objects over or near the antenna.

16. Do not use the product to report a gas leak while in the vicinity of the leak.

~7~

17. Do not install the base station or the handset charger near microwave ovens,

~8~

radios, TV sets, speakers, or other electrical equipment. These appliances may cause interference to the product or experience interference from the product.

18. Unplug the base station or the charger adaptor from the power outlet and refer

to an authorized service center under the following conditions:

a. If liquid has been spilled into the product. b. When the power supply cord or plug is damaged or frayed. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the operating

instructions.

e. If the product has been dropped or housing has been damaged. f. If the product shows a distinct change in performance.

Battery Safety Instructions

1. Use only manufacturer approved Li-Ion rechargeable batteries and charger. Do

not use other types of rechargeable batteries or non-rechargeable batteries. The batteries could short-circuit, and the battery enclosure may be damaged causing a hazardous condition.

2. Follow the charging instruction in this manual and instruction labels and

markings in the handset and charger compartments.

3. Battery must be recycled or disposed of properly. Do not dispose the battery in

a fire. The cells may explode.

4. Do not dispose of the battery in municipal waste. Check with local codes for

disposal instructions.

5. Exercise care in handling the batteries so you do not short-circuit the battery

with conductive materials such as rings, bracelets, keys, pocketknives, and/or coins. The battery or conductive material may overheat and cause burns or fire.

6. Do not expose batteries to rain or water.

7. Do not open or mutilate the battery. Released electrolyte is corrosive and may

cause injury to eyes or skin. The electrolyte may be toxic if swallowed.

8. During charging, the battery heats up. This is normal and is not dangerous.

Regulatory Information

DuraFon-SIP System FCC ID: A8J-SP935 IC: 10103A-SP935

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received, including

interference that may cause undesired operation.

Privacy of communications may not be ensured when using this phone.

Base Station

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

~9~

~10~

IMPORTANT NOTE: FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Statement:

This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE: Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

This device has been designed to operate with an antenna having a maximum gain of 2 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

Portable Handset

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

IMPORTANT NOTE: Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Statement:

IMPORTANT NOTE: Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with IC RF exposure compliance requirements, please follow operation instruction as documented in this manual.

This device has been designed to operate with an antenna having a maximum gain of 2.5dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The required antenna impedance is 50 ohms.

~11~

Equipment Checklist

~12~

Antenna

Travel charger jack

Battery pack

4-line LCD

TALK/FLASH/



Microphone

1. In a Base + Handset package, please find the following components: a. Base Station x 1 (antenna installed) b. Base AC/DC Adapter x 1 c. Handset x 1 (antenna installed) d. Handset Antenna x 1 (Long ×1) e. Desktop Charger x 1 f. Charger AC/DC Adapter x 1 g. 1700mA Li-Ion Battery Pack x 1 h. Telephone Cord x 1 i. Quick Guide j. RJ45 cable x 1

2. In a Handset package, please find the following components: a. Handset x 1 (antenna installed) b. Handset Antenna x 1 (Long ×1) c. 1700mA Li-Ion Battery Pack x 1 d. Desktop Charger x 1 e. Charger AC/DC Adapter x 1 f. Quick Guide

3. Optional Accessory a. Outdoor Antenna Kit (including antenna and cable) b. High-Gain Handset Antenna c. Headset

Handset Illustration

Belt Clip Holder

Receiver

Volume control / Scrolling

Broadcast key

END & Power ON/OFF key

2-WAY/ INTERCOM

(For SIP)

Headset jack (2.5mm)

~13~

Handset Features

characters

~14~

2. Ringer

Rings to an incoming ca

ll and intercom call

Distinctive alert sounds indicating various events:

Places or answers a telephone or intercom call

compan

ies during a call.

during incoming, outgoing or intercom call.

or all registered handsets.

assistance

of the base

station

Half duple

x broadcasting to handsets for immediate announcement

Half duplex broadcasting to base stations

Make menu selection.

Basic Handset Features

1. 4-Line LCD (Liquid Crystal Display) a. The LCD display has LED (Light Emitting Diode) for backlighting. b. The 1st line of LCD consists of icons. c. Icons explanation from left to right

(1) RSSI level (Receive Signal Strength Indicator)

During a call, the number of bars is proportional to

the radio signal strength received.

(2)

(3) Line, Sound and Indication

Link mode (2.1) Call in-progress (ON/OFF-Hook)

Indicates if the phone line is in the OFF-Hook status.

(2.2) Intercom in-progress

Indicates if Intercom mode is active. Indicates the Handset ID that is sending the intercom call.

(3.1) Line Indicator

Indicates when using line 1 or the incoming call from FXO line.

(3.2) SIP Indicator

Indicates when using SIP or the incoming call from SIP.

e. The last line displays the left and right soft keys.

(1) Single beep: successful key entry. (2) Double beep: indicates power on/off. (3) Triple beep: failed operation. (4) Periodic 1-Long 2-Short beeps (every 1 minute): low battery warning; out of

range; call on hold.

Re: No beep: invalid key entry.

3. TALK/FLASH ( )

b. Sends a Flash signal to the phone line to retrieve a dial tone after the call

ends, or to perform the Call Waiting feature provided by local phone

4. SPEAKERPHONE ( )

Press and hold the key for over 2-seconds to enable/disable the speakerphone

(3.3) Enable ringer

(4) Disable PA and indicate speaker phone

(5)

(6)

(3.4) Disable ringer

(3.5) Ringer and vibrate mode

(3.6) Vibrate mode

(3.7) Message waiting indicator

(4.1) Indicates if the incoming broadcast is disabled.

(4.2) Speaker indicator

Indicates if the speakerphone is active.

Two-Digit Handset ID

Displays the 2-digit Handset ID of owner.

Battery Strength

Number of bars is proportional to the amount of battery time remaining.

d. The 2nd and 3rd lines of the LCD, maximum 16-characters each, display

status, message, menu selections, or user-editable alphanumerical

2-WAY INTERCOM (( ))

a. Places an intercom call to another handset, a group handset (group paging)

b. Intercom calls are digital, full duplex, and are conducted without the

6. BROADCAST ( )

Re：Press the key on the left top corner of the handset to activate the broadcast function.

7. Left/Right Soft Keys ( )

~15~

Scroll through records and menu selections.

Adjust rec

eiver voice volume when in

the

Talk mode

Leaves current menu

operation, up one level

Press for 3

seconds to

turn

off the power

1. Multiple

andsets

egistration

ID 10-19: Individual Handset ID

Group ID

2. Ringer

Vibrator

Two (2) options for Line (incoming call) ringing

and i

ntercom ringing.

(

Off/Low/Medium/H

igh/Vibrate/

ibrate

& High

) for each opti

on.

3. Caller ID

service from local telephone company)

4. Call Waiting with

Caller ID

company)

5. Name

agging with

aller ID

Caller ID

service from local tel

ephone company)

~16~

DND (Do Not Disturb, i.e., Silent Ring)

Up ( ) /Down ( ) Scrolling Keys

Press to enter received call log when in the Standby mode.

Press to enter phonebook when in the Standby mode.

END; On/Off Key ( )

Ends a call.

Additional Handset Features

c. ID 1~7: Group IDs. Handsets can “subscribe” from the handset menu to

b. Six (6)-level ringer volume selections

Displays incoming call phone number and name on the LCD (needs Caller ID

Displays 2nd incoming call information on the same phone line when 1st call is in

Match the Caller ID with the phone book entries; once matched, the LCD

Up to 10 handsets can be registered to a base station.

group(s) and be paged when a landline caller or an intercom caller enters a

Eight (8) ringer type selections for each option.

progress (needs Call Waiting with Caller ID service from local telephone

screen will display the name or nickname instead of pure Caller ID info (needs

7. Call Logs

a. Redial: Stores 10 phone numbers (up to 26-digits each) dialed most

recently. Can perform last-number redial on all 10 numbers.

b. Received and New Call Log: Total 50-entries (16-digit phone number, 16-

character names, and Date/Time stamp), needs Caller ID service from local telephone company.

c. Phone numbers and names can be saved into phone book while in display.

8. Call Manager: Includes: blocking incoming call, outgoing call and assign line dedication, line selection.

a. Incoming Call: a-1. PA On/Off: Enable or disable the Broadcast feature from other

handsets or the base station. When PA is Off, the handset cannot receive Broadcast calls from the base station or other registered handsets, but it can Broadcast to the base station or other registered handsets.

a-2. Line On/Off: Enable or disable the ability to receive incoming calls

from telephone line call. When Line is Off, the handset cannot receive incoming calls from a telephone line call, but it can still make outgoing calls.

a-3. Int. On/Off: Enable or disable the Intercom from other handsets or the

base station. When Int. is Off, the handset cannot receive Intercom calls from the base station or other registered handsets, but it can Intercom to the base station or other registered handsets.

b. Outgoing Call Select the mode of line selection (Auto/Manual/Predefine line/Off) when

you make a line call. b-1. Auto: A handset will select one of available lines from subscribed bases before making an outgoing call. (Default)

b-2. Manual: A handset will be prompted to select from a list of available

lines before making an outgoing call. (1 for telephone line, 5 for SIP call)

~17~

c-1.

Block

users from dialing long distance or international calls

hanging

requires

you

to enter the “Call Settings

” (

-4-3).

feature

. The default password is

“

0000

.”

10. Key-G

uard

Press

UNLOCK

(Left) soft key followed by

release

it.

mode

for 15-

seconds

11.

Dialing Prefix

when dialing from call logs, phone

book, and dial

and-send dialing.

12.

Call Hold

Places call on hold

13. Mute

ress

UNMUTE

(Left) soft key to release it.

14.

Phone

Book

name (up to

16-character

s).

Alphabetically sorted display

and search

by letter.

Dial from display

~18~

Phone

ook transfer via air

i. Transfer

specific

hone

Book to one handset or all registered

handsets

ii. Tran

sfer all

hone

Books to one handset or all registered handsets

15. Key Tone

Four-level

Key Tone volume selections (

Off/Low/Medium/High

Four

Key Tone type selections

16. Call Timer

the call

the DuraFon

SIP, which is adjunct to the PBX system.

those functions during the call by pressing

the OPTION

soft key.

18. Menu Display

8), the defaul

t handset password is “0000

.”

abled by entering Menu Display

again.

Enable or disable the

roadcast function.

20.

Group Setting

Re: U

p to 7

groups

(1~7) can be subscribed.

a. Chang

e the “

DuraFon

SIP” screen to the desired wording or info, such as

b-3. Off: Disable the capability to make an outgoing call.

c. Call Barring

c-2. Up to 5-digits of each Call Barring setting, up to 5-entries allowed.

Note: You must key in the accurate user ID and password to perform this

Any Key Answer (except and SILENT soft Key)

9. a.

If you enable Any Key Answer while you have two incoming line calls

simultaneously, you can answer the SIP call or PSTN call by pressing

the scrolling key.

a. Displays call time duration for current call, during and immediately after

17. Programmable Feature Call

a. Allows user to pre-program the most frequently used Feature codes into

b. Up to 10-entries can be saved. c. Once the feature code has been programmed, you can quickly perform

a. When the Key-Guard is selected, all keys will be locked.

＊

b. The Key-Guard will be automatically enabled once returning back to idle

a. Up to 14-digits, including pause(s), one access code can be pre-

programmed to be added automatically in front of the dialed number

a. Press MUTE (Left) soft key during talk, the handset microphone will be

muted.

a. 50-entries, each stores a phone number or handset ID (up to 26-digits) and

d. During the stand-by mode, you can enter the phone book by pressing

a. To avoid mis-setup in the “Call Settings”(MENU-4), “Phone Settings”

(MENU-5), and “Base Settings” (MENU-6), these settings can be hidden.

b. The Handset password is required before entering Menu Display (MENU-

c. When disabling the settings, they will no longer be displayed unless

19. PA On/Off

a. Allows the handset to subscribe to one or several groups.

21. Custom Name

When PA is Off, the handset cannot receive Broadcast from the base station or other registered handsets; but it can broadcast to other registered handsets.

~19~

the handset user’s name.

Re: Up to 32

characters can be entered.

(

-4-

3) and Menu Display

(MENU

8).

23. DTMF

Duration

(from web

)

24. P

rogrammable Flash

Key Timing

(from web

)

25. Assign

ext Handset ID for

ew Handset

new handset.

handset ID to a new handset.

When entering the

ase Setting

s, a

PIN is required.

The

Default is “0000

.”

26. Clear Handset

handset, in case the

other registered handset is defected.

new handset

in its place

When entering the

ase Setting

s, the

PIN is required. Default is “0000

.”

27. Change PIN

To c

hang

e the base PIN

, enter

the “Base Settings” (

-6-3).

a. Us

e a registered handset to change

the

PIN from

-6-3.

The d

efault PIN is “0000

.”

“0000

.”

28.

Auto Hang Up

Feature

(from web)

hang up feature.

when the far

end ha

ngs up

its call.

29.

Mic Gain

environment

s – Quiet, Normal and Noisy environment.

~20~

This requires enter

ing the “Phone Settings

” (

-5-

1).

30.

Headset Ring

This requires entering the “Phone Settings

” (

-5-8).

31 Base

ntercom Auto

Answer (

from w

eb)

On/O

ff the

ntercom

uto-A

nswer feature

22. Change Pwd a. Change the handset password, which requires entering the Call Barring

Re: Default PIN is “0000.”

a. Use a registered handset from MENU-6-1 to assign a Next Handset ID to a

b. If you do not assign Next Handset ID, the system will automatically assign a

a. Use a registered handset from MENU-6-2 to remove the other registered

b. Once the other registered handset is clear, the user is able to register a

Change the ringer emitting either from the handset speaker or the headset

receiver.

a. From Web, “System-Base Settings-Base Intercom Auto-Answer” to turn

Default is ON, If turning OFF the feature, you will need to press the base Intercom or Broadcast key to answer handset Intercom calls to the base.

c. When entering the Base Settings, the PIN is required. The default PIN is

a. From Web, “System-Base Settings-Auto Hang up” to turn On/Off this auto

b. If turning On the feature, the handset will automatically hang up the call

Change the handset microphone gain based on the handset’s use in different

~21~

GROUND

DC In

UDIO IN

CONSOLE

INE

EGISTER

ESET LAN

Broadcast

Intercom

Volume

Antenna

Receiver

Microphone

~22~

Audio

-In Jack

(3.5mm)

FXO Jack (L1)

Standard

RJ-11 connector

to plug in the telephone line

Ethernet Jack

Standard

RJ-45 connector

to plug in the

Ethernet

(LAN)

line.

Console

ack

Jack for

console

(Type

B USB connector)

GND

Connecting the ground cable

REG button for Registration and Page

enter registration mode

handset to stop.

7. RESET Button

Restores base station to factory settings

Reset button is in

ended to preve

nt accidental system reset.

to factory setting

DC In: to plug in the

12V DC

power adapt

er.

Base Illustration

Base Features

Basic Base Station Features

Connect to an external device for music on hold.

a. Press and hold this REG button until the “INTERCOM” LED flashes status to

b. To search for a misplaced handset; press “REG” button, all registered

handsets will beep for 30-seconds. Press “REG” again or any key on the

c. All handsets (including administrator) and additional base(s) need to be re-

registered after a base station reset. The web configuration is also to reset

~23~

~24~

1. DC In

Connects to Charger AC Adapt

er.

2. Handset Charging Slot

Charge

s handset battery when

handset is placed in

the

cradle.

Refer to the handset LCD for charging status

3. It is impossible to overcharge the battery using this charger.

on the LCD.

Charger Illustration

DC In

Spare Battery Charging Slot

Spare Battery Charging Indicator

Handset Charging Slot

Charger Features

(1) Charging: battery status bar is running and the LCD screen shows: “Charging.” (2) Fully Charged: battery status bar stands still and the LCD screen displays

“Charge Complete.”

(3) Charge Fail: If an error occurs during charging mode, the LCD screen will

display “Charge Fail.”

4. The charging station adapter can also be used as a travel charger. However, you cannot turn off the power while you charge the handset via the travel charger. A warning message, “Unplug Travel Charger then OFF” will be shown

Notes:

1. Fully charge battery packs before first use.

2. Handset will “power on” automatically when placed on the charging

slot.

3. However, if you drain the battery completely, it will take

approximately one minute for the handset to auto power on.

+ 27 hidden pages

EnGenius DuraFon-SIP User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual