ENFORCER MVE-AH010Q User Manual

ENFORCER HDMI Extender over Dual Cat5e/6

NOTICE

:

or in part, without the written

permission of SECO

-

LARM.

WARRANTY:

SECO

-

LARM

HDMI, the HDMI Logo and High

-

Definition Multimedia Interface are trademarks or registered trademarks of HDMI

Troubleshooting:

•

Also Available from

SECO

-

LARM

:

FORCER

AH010Q

Dual

•

resolutions from 480i to 1080p with zero signal loss

0m) at 1080p over two Cat

comes as a complete set

hrough for remote control extension

Up to

196ft

(60m)

1080p Resolution

Up to

and

Operation Dual Cables

Reduce the resolution of the source device

• Turn off deep color

• Use T568B wiring standard

• Make sure the Cat5e/6 cables are connected to the correct

HDMI Device does not function correctly

HDMI Switch HDMI Splitter High-Speed HDMI Cables

Extenders

for HDMI

Wireless Extender for HDMI HDMI Matrix

ports, and not to opposite ports

• Use solid core cable instead of stranded core cable

• Make sure the HDMI input device is turned on

• Make sure the HDMI output device is turned on

• Test the Cat5e/6 cable between the receiver and transmitter

to make sure it is operational

®

®

EN

MVE-

HDMI® Extender over

Manual

Cat5e/6

Licensing LLC in the United States and other countries.

normal service for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s
obligation is limited to the repair or replacement of any defective part if the unit is returned, transportation prepaid, to
SECO-LARM. This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or
abuse, neglect, repair or alteration, improper or abnormal usage, or faulty installation, or if for any other reason
SECO-LARM determines that such equipment is not operating properly as a result of causes other than defects in material
and workmanship. The sole obligation of SECO-LARM and the purchaser’s exclusive remedy, shall be limited to the
replacement or repair only, at SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral,
incidental, or consequential personal or property damage of any kind to the purchaser or anyone else.

SECO-LARM policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right
to change specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.
Copyright © 2016 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole

16842 Millikan Avenue, Irvine, CA 92606 Website: www.seco-larm.com

Tel: [phone] | [phone] Email: [e-mail]

4 SECO-LARM U.S.A., Inc.

This SECO-LARM product is warranted against defects in material and workmanship while used in

The information and specifications printed in this manual are current at the time of publication. However, the

®

U.S.A., Inc.

MI_MVE-AH010Q_151222.docx

PICHN3

Cat5e/6

Plug
Play

Extend HDMI over two Cat5e/6 cables

• Supports

• Transmits up to 196ft (6

• Plug and play operation –

• IR Pass-t

6 cables

ENFORCER HDMI Extender over Dual Cat5e/6

Introduction:

The ENFORCER HDMI Extender over Cat5e/6 extends the range of HDMI by using a transmitter

Features:

•

operation of devices.

Specifications:

Parts List:

1

x Transmitter (MVE

-

AH010Q

-

TQ)

1x Manual

Model Number

MVE-AH010Q

Input Video signal

3.3V

Input DDC signal

5Vp-p (TTL)

Maximum single link range

1080p

Deep color

24bit

Video formats supported

High-speed HDMI, HDCP 1.2

Audio formats supported

LPCM, Dolby

-

AC3, DTS7.1, DSD

Output video

HDMI

Resolutions supported

1080p/1080i/720p/576p/576i/480p/480i

Cat 6 Up to 196' (60m)

Cat5e Up to 98' (30m)

Video amplifier bandwidth

1.65Gbps

Video input connector

HDMI Type A 19

-

pin female

Maximum input cable length

24AWG (15m), 26AWG

(10m), 28AWG (5m)

Video output connector

HDMI Type A 19

-

pin female

Maximum output cable length

24AWG (15m), 26AWG (10m), 28AWG (5m)

Cat5e/6 Wiring standard

T-

568B

Operating voltage

5VDC

Power supply

1A@5VDC (1 adapter) (2.1mm plug)

ESD protection (human body model)

±8kV (air

-

gap discharge), ±4kV (contact discharge)

Transmitter

550mA@5VDC

Receiver

450mA@5VDC

Operating

temperature

32°~104° F (0°~40° C)

Operating humidity

20~90% RH (no condensation)

Dimensions

31/8”x15/8”x1” (81x49x25 mm)

Weight 5.3-oz (150g) (each)

Overview:

5VDC

Power Input

Installation:

1. Determine the location

s where the HDMI to Cat5

e/6 units will be

placed

as well as how much Cat5

e

/6 cable

Sample Application:

Transmitter

HDMI

C

at5e/6

Remote

Included 5VDC

IR Tx

Remote

IR Rx

Receiver

Status

LED

HDMI

put

Status

HDMI Extender over Cat5e/6

HDMI Extender over Cat5e/6

Receiver

Transmitter

Extender for HDMI over Cat5e/6

Extender for HDMI over Cat5e/6

ENFORCER HDMI Extender over Dual Cat5e/6

and an active receiver to send video and audio over two Cat5e/6 cables. HDMI Formats as high
as 1080p can be transmitted up to 196ft (60m) between the two units with zero signal loss.

Signal Strength –Transmitter ensures that the signal strength will remain strong over the length

of the cable.

• Distance – The HDMI Extender over Cat5e/6 is capable of providing a clear HDMI signal up to

196ft (60m).

• Formats Supported – The HDMI Extender over Cat5e/6 supports both progressive and

interlaced formats: 1080p/1080i/720p/576p/576i/480p/480i.

• Plug and Play – The HDMI Extender over Cat5e/6 comes as a complete set consisting of a

transmitter, receiver, and power supply. No adjustments or settings must be made, the unit is
ready to use right out of the box.

• Zero Signal Loss – Integrated circuits in the transmitter and receiver clean, buffer and amplify

the HDMI signal to prevent signal loss and ensure a clear signal regardless of the length of the
cable.

• IR Pass-Through – Send IR signals from the HDMI source to the HDMI monitor for discrete

Range – 1080p

IR-Tx Port

In

Cat5e/6 Ports

IR Tx Port

IR-Rx Port

Cat5e/6 Ports

Output

LED

will be necessary.

2. Connect the HDMI to cable to both the transmitter and source device.

3. Connect the HDMI cable to both the receiver and display.

4. Connect the Cat5e/6 cables to both the receiver and transmitter units. Make sure to connect the cables to

their respective ports, i.e. Cat5e/6-1 connected to Cat5e/6-1, and Cat5e/6-2 connected to Cat5e/6-2.

Note: For best results, use Cat6 cable.
Note: For best results, use solid core cable. Stranded core cable is not recommended.

5. Connect the 5VDC adapter to the receiver unit.

6. Switch on the HDMI source device and display to verify that the system is functioning properly.

7. Install the IR transmitter to the IR-TX port, pointing the IR transmitter at the device to be controlled. Install

the IR receiver to the IR-RX port of the other device, pointing the IR receiver to where the remote control
will be. Point the remote control at the IR receiver when in use.

Current draw

1x Receiver (MVE-AH010Q-RQ)
1x 5VDC Power adapter

1x IR Transmitter (w/ double sided tape)
1x IR Receiver (w/ double sided tape)

2 SECO-LARM U.S.A., Inc.

Cable Legend:

HDMI

HDMI Source

Power
IR

Power Adapter

Display

SECO-LARM U.S.A., Inc. 3