ENFORCER EV-1665-N2BQ User Manual

MANUAL

EV-1665-N2BQ

Wide Angle Bullet Camera

Note: Model numbers that end with “Q” or products that have a round green “Q” sticker signify RoHS compliance.

550 TV Lines

1/

3

”

Sony Super HAD II CCD

2.2mm Lens with a 170° Viewing Angle

ENFORCER WIDE ANGLE BULLET CAMERA

IMPORTANT

Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this
product in violation of any current laws or statutes.

WARNING

Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not
open the case of this device, as there are no field serviceable components inside.

FCC COMPLIANCE STATEMENT

Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communicati

ons.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.

WARRANTY: This SECO LARM product is warranted against defects in material and workmanship while used in normal service

for a period of one (1) year from the date of sale to the original consumer customer. SECO LARM’s obligation is limited to the
repair or replacem

ent of any defective part if the unit is returned, transportation prepaid, to SECO LARM.

This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, r

epair, or
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO LARM determines that such
equipment is not operating properly as a result of causes other than defects in material and workmanship.
The sole obligation of SECO LARM, and the purchaser’s exclus

ive remedy, shall be limited to replacement or repair only, at
SECO LARM’s option. In no event shall SECO LARM be liable for any special, collateral, incidental, or consequential personal or
property damages of any kind to the purchaser or anyone else.

NOTICE

The information and specifications printed in this manual are current at the time of publication. However, the SECO LARM policy
is one of continual development and improvement. For this reason, SECO

LARM reserves the right to change specifications
without notice. SECO LARM is also not responsible for misprints or typographical errors.
Copyright © 2009 SECO LARM U.S.A., Inc. All rights rese rved. This material may not be reproduced or copied, in whole or in
part, without the written permission of SECO LARM.

U.S.A., Inc.

16842 Millikan Avenue, Irvine, CA 92606

Website: www.seco larm.com

Tel: [phone] Fax: [phone] E mail: sales@ seco larm.com

mi EV 1645 N2BQ docx

PIKSR1

Troubleshooting

The screen is blank.

Check that the camera is powered up.

Check that the power supply’s polarity is

correct.

Check that the monitor is powered up.
Check that the video cable connecting the

camera to the monitor is connected properly.

The screen image is dim.

Clean the lens using a soft, clean cloth.
Check that the light source is adequate.

The screen image has poor
contrast.

Adjust the monitor’s contrast knob.
Change the position of the camera.

The screen image flickers.

Change the position of the camera.

The screen image is
distorted.

Change the position of the camera.

The camera case is hot.

Check that the correct power supply is in use.

ENFORCER WIDE ANGLE BULLET CAMERA

Installation:

1. Please read this manual carefully and keep it for

future reference.

2. Use the camera within given temperature and

electrical limits.

3.

Do not mount the camera where it is exposed to
rain or other moisture, or in humid or dusty
places.

4. Do not point the camera at the sun. Heat could

damage the camera, even when not in use.

5. Do not mount the camera in areas exposed to

radiation, strong magnetic fields, or strong
electrical signals.*

6. Do not open or disassemble the camera.

There are no field-serviceable parts inside.

7. Do not drop the camera or subject it to strong

vibrations.

Note: Many video monitors produce strong

electromagnetic fields close to the display
CRT, especially when the mon

itor is turned on
or during de-Gaussing, which occurs
automatically with many monitors when the
monitor is turned on.

Before Starting:

1. Run a 12VDC power supply wire and a video

cable with a male BNC connector through the
wall to where the camera is to
be mounted.

2. Temporarily connect the camera to the power

supply. Do not cut DC jack or female BNC

connector as warranty will be voided. If
needed, use the included pigtail connector.

3. Temporarily connect the camera’s female BNC

connector to the video cable’s male
BNC connector.

4. While watching the monitor, hold the camera

against the wall or ceiling by hand where it is to
be mounted, then turn the camera until it is
certain that this mounting location is correct.

Use a pencil to mark the location of the six
screw holes in the mounting plate.

5. Disconnect the power supply and video cable.

6. Mount the mounting plate to the wall or ceiling

using the six included mounting screws. If the
wall is made of dry wall, brick, or similar
material, it may be necessary to use screw
anchors (not included).

7.

Reconnect the power supply and video cable.
Turn the monitor on and make sure the camera
is sending the proper video signal.

8. Adjust the camera angle using the

adjustment nut.

9. Do a final test of the video camera and

monitor.

Overview:

Camera

Mounting holes

Adjustment nut

Important:

Do not cut DC jack or female BNC conn ector as warranty will be voided.

DC jack

Connect to video cable’s

male BNC connector

BNC connector

Pigtail connector

Mounting bracket

ENFORCER WIDE ANGLE BULLET CAMERA

Type

Wide-Angle Bullet Camera

CCD

1

/3” Sony Super HAD II Color CCD

Resolution

Color: 550 TV Lines

B/W: 590 TV Lines

Pickup elements

768x494 pixels

Video output format

NTSC

Video output

1.0Vp-p composite video, 75Ω

Lens

2.2mm

Viewing angle

170°

Minimum illumination

0.1-lux at F/1.4

S/N ratio

>48dB

Scanning frequency

15.734KHz x 59.94Hz

Sync

Internal

Gamma correction

0.45

Gain control

Auto

IP rating

IP66

Power source

12VDC

Current draw

83mA

Operating temperature

14°~122° F (-10°~50° C)

Dimensions

31/2”x17/16”x17/16” (90x37x37 mm)

Weight

6-oz (160g)

Specifications

31/2” (90mm)

19/16” (40mm)

19/16”

(40mm)

17/16”

(37mm)

Parts List:

Dimensions:

1 x Manual
6 x Mounting screws

51/2” (140mm)

1 x Pigtail connector

1 x Camera
1 x Mounting bracket