Enforcer EFI16EA, EFI16 User Manual

SAFETY DATA SHEET

A07250 ENF FLY INSCT EFI16 20N16

Version 1.1

Revision Date 06/07/2018

Print Date 04/24/2019

Material name

:

Enforcer Flying Insect Killer III

EPA ID Number:

40849-4
Material number

:

EFI16

Company

:

Zep Commercial Sales & Service, a unit of Zep, Inc.

Address

:

350 Joe Frank Harris Parkway, SE
Emerson, GA 30137
Telephone

:

404-352-1680

Emergency telephone numbers

For SDS Information

:

Compliance Services 1-877-428-9937

For a Medical Emergency

:

877-541-2016 Toll Free - All Calls Recorded

For a Transportation
Emergency

:

CHEMTREC: 800-424-9300 - All Calls Recorded.
In the District of Columbia 202-483-7616

Recommended use

:

Pesticide
Appearance

Aerosol containing a liquefied gas

Colour

clear

Odour

mild, characteristic

Flammable aerosols

:

Category 2

Gases under pressure

:

Liquefied gas

Hazard pictograms

:

Signal word

:

Warning

Hazard statements

:

H223 Flammable aerosol.
H280 Contains gas under pressure; may explode if heated.

Precautionary statements

:

Prevention:
P210 Keep away from heat, hot surfaces, sparks, open flames
and other ignition sources. No smoking.
P211 Do not spray on an open flame or other ignition source.

SECTION 1. PRODUCT AND COMPANY IDENTIFICATION

Manufacturer or supplier's details

Recommended use of the chemical and restrictions on use

SECTION 2. HAZARDS IDENTIFICATION

Emergency Overview

GHS Classification

GHS label elements

1 / 11

SAFETY DATA SHEET

A07250 ENF FLY INSCT EFI16 20N16

Version 1.1

Revision Date 06/07/2018

Print Date 04/24/2019

P251 Pressurized container: Do not pierce or burn, even after
use.
Storage:
P410 + P412 Protect from sunlight. Do not expose to
temperatures exceeding 50 °C/ 122 °F.
Disposal:
P501 Dispose of contents/container in accordance with local
regulation.
Substance / Mixture

:

Mixture

Chemical name

CAS-No.

Concentration [%]

butane

106-97-8

>= 10 - < 20

alkanes, C12-14-iso-

68551-19-9

>= 5 - < 10

propane

74-98-6

>= 1 - < 5

General advice

:

Move out of dangerous area.
Show this safety data sheet to the doctor in attendance.
Do not leave the victim unattended.
Get medical attention if symptoms occur.

If inhaled

:

If unconscious, place in recovery position and seek medical
advice.
If symptoms persist, call a physician.

In case of skin contact

:

Wash off immediately with plenty of water.
Remove contaminated clothing and shoes.
Wash contaminated clothing before reuse.
If skin irritation persists, call a physician.

In case of eye contact

:

Rinse immediately with plenty of water, also under the eyelids.
If eye irritation persists, consult a specialist.
Remove contact lenses.
Protect unharmed eye.
Keep eye wide open while rinsing.

If swallowed

:

Keep respiratory tract clear.
Never give anything by mouth to an unconscious person.
If symptoms persist, call a physician.
DO NOT induce vomiting unless directed to do so by a
physician or poison control center.

Most important symptoms
and effects, both acute and
delayed

:

Effects may be delayed, symptoms may include minor eye or
skin irritation.
Overexposure may cause mild eye or skin irritation.

SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS

Hazardous components

The exact percentages of disclosed substances are withheld as trade secrets.

SECTION 4. FIRST AID MEASURES

2 / 11

SAFETY DATA SHEET

A07250 ENF FLY INSCT EFI16 20N16

Version 1.1

Revision Date 06/07/2018

Print Date 04/24/2019

Notes to physician

:

Treat symptomatically. Symptoms may be delayed.

Suitable extinguishing media

:

Water spray jet
Carbon dioxide (CO2)
Alcohol-resistant foam
Dry chemical

Unsuitable extinguishing
media

:

High volume water jet

Specific hazards during
firefighting

:

Do not allow run-off from fire fighting to enter drains or water
courses.

Hazardous combustion
products

:

Carbon dioxide (CO2)
Carbon monoxide
Smoke

Specific extinguishing
methods

:

Use extinguishing measures that are appropriate to local
circumstances and the surrounding environment.

Further information

:

Collect contaminated fire extinguishing water separately. This
must not be discharged into drains.
Fire residues and contaminated fire extinguishing water must
be disposed of in accordance with local regulations.
Use a water spray to cool fully closed containers.

Special protective equipment
for firefighters

:

Wear self-contained breathing apparatus for firefighting if
necessary.

Personal precautions,
protective equipment and
emergency procedures

:

Use personal protective equipment.
Ensure adequate ventilation.
Remove all sources of ignition.
Evacuate personnel to safe areas.
Beware of vapours accumulating to form explosive
concentrations. Vapours can accumulate in low areas.

Environmental precautions

:

Prevent product from entering drains.
Prevent further leakage or spillage if safe to do so.
If the product contaminates rivers and lakes or drains inform
respective authorities.

Methods and materials for
containment and cleaning up

:

Soak up with inert absorbent material (e.g. sand, silica gel,
acid binder, universal binder, sawdust).
Sweep up or vacuum up spillage and collect in suitable
container for disposal.

SECTION 5. FIREFIGHTING MEASURES

SECTION 6. ACCIDENTAL RELEASE MEASURES

3 / 11

SAFETY DATA SHEET

A07250 ENF FLY INSCT EFI16 20N16

Version 1.1

Revision Date 06/07/2018

Print Date 04/24/2019

Advice on safe handling

:

Avoid exposure - obtain special instructions before use.
Avoid contact with skin and eyes.
For personal protection see section 8.
Do not breathe vapours or spray mist.
Take precautionary measures against static discharges.
Provide sufficient air exchange and/or exhaust in work rooms.
Dispose of rinse water in accordance with local and national
regulations.
Always replace cap after use.

Conditions for safe storage

:

BEWARE: Aerosol is pressurized. Keep away from direct sun
exposure and temperatures over 50 °C. Do not open by force
or throw into fire even after use. Do not spray on flames or
red-hot objects.
No smoking.
Observe label precautions.
Keep in a dry, cool and well-ventilated place.
Electrical installations / working materials must comply with
the technological safety standards.

Materials to avoid

:

Oxidizing agents

Components

CAS-No.

Value type
(Form of
exposure)

Control
parameters /
Permissible
concentration

Basis
butane

106-97-8

TWA

800 ppm
1,900 mg/m3

NIOSH REL

TWA

800 ppm
1,900 mg/m3

OSHA P0

PEL

800 ppm
1,900 mg/m3

CAL PEL
propane

74-98-6

TWA

1,000 ppm

ACGIH

TWA

1,000 ppm
1,800 mg/m3

NIOSH REL

TWA

1,000 ppm
1,800 mg/m3

OSHA Z-1

TWA

1,000 ppm
1,800 mg/m3

OSHA P0

PEL

1,000 ppm
1,800 mg/m3

CAL PEL

Engineering measures

:

effective ventilation in all processing areas

Respiratory protection

:

Use respiratory protection unless adequate local exhaust
ventilation is provided or exposure assessment demonstrates

SECTION 7. HANDLING AND STORAGE

SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Components with workplace control parameters

Personal protective equipment

4 / 11