Enernet 130 User Manual

Pub No. 13001-082207

ENERNET Corporation Copyright 2007

Model 130 User Guide

Communicating Thermostat Wireless RS485 Accessory

MODEL 13000 Application Guide

ENERNET CORPORATION IS NOT RESPONSIBLE FOR ANY
RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.

THIS EQUIPMENT COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE
THAT MAY CAUSE UNDESIRED OPERATION.

ENERNET CORPORATION PROVIDES THIS PUBLICATION “AS
IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE.

THIS MANUAL MAY CONTAIN TECHNICAL INACCURACIES
AND/OR TYPOGRAPHICAL ERRORS. CHANGES ARE
PERIODICALLY MADE TO THIS MANUAL, WHICH ARE
INCORPORATED IN LATER EDITIONS.

ENERNET CORPORATION MAY MAKE CHANGES AND
IMPROVEMENTS TO THE PRODUCT(S) AND/OR PROGRAMS
DESCRIBED IN THIS PUBLICATION AT ANY TIME WITHOUT
NOTICE.

IN NO EVENT WILL ENERNET CORPORATION BE LIABLE FOR
DAMAGES, INCLUDING LOST PROFITS, LOST SAVINGS OR
OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OF OR INABILITY TO USE SUCH
PRODUCT, EVEN IF ENERNET CORPORATION OR AN
APPROVED RESELLER HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES, OR FOR ANY CLAIM BY
ANY OTHER PARTY.

E NERNET

Corporation

307 Dewittshire Road, Syracuse, New York 13214

Phone: [phone] Fax: [phone]

MODEL 13000 Application Guide

ANTENNA

The wireless RF equipment described in this document may be
supplied with one of two possible antenna configurations.

Stick-On 1/2-wave Dipole Antenna:

Antenna Factor P/N ANT-916-MHW -RPS

PCB Mounted 12-Inch Coaxial Monopole:

ENERNET P/N 060-012

EQUIPMENT MANUFACTURER (OEM)

The Original Equipment Manufacturer (OEM) must ensure that
FCC labeling requirements are met. This includes a clearly visible
label on the outside of the final product enclosure that displays the
following:

CONTAINS FCC ID: TGD13000

MODEL 13000 Application Guide

1

Figure 1: Aprilaire 8870 Thermostat — Model 130 Remote Communication Node

PB1— SERIAL LOOP BACK TEST

A valid 8870 thermostat command is sent ov er the
RS485 interface. A valid return data string is
expected.

? Green LED (D5) flash = PASS
? Red LED (D4) flash = FAILED.

PB2 — RF COMMUNICATION TEST
Initiates a 5-second communication test with the
model 130 Master transceiver it has been linked to. .

? Green LED (D5) flash = PASS
? Red LED (D4) flash = FAILED

PB3 — CONFIGURATION SETUP
Holding PB3 down for 3-seconds places unit into
configuration setup (see Configuration Setup section
for details).

PB2 + PB3 — INSTALLATION MODE
Simultaneously pressing PB2 & PB3 places the
model 130 Remote Communication Node (RCN) into
Installation Ready mode for a 5-

second period during

which time it can be linked to a Master Transceiver.
The Yellow LED (D3) and Green LED (D2) will
simultaneously light to indicate the RCN is in
Installation Ready mode.

PB1 PB3 PB2

D1D2

D3

D5D4

RED ( R )

BLK ( C )

YEL (A+)

BLUE (A-)

WH (B+)

GRN (B-)

J2

Power Supply

Network

Processor

ANT

Thermostat

24VAC Power

Crystal

Serial Interface

8870 Thermostat

Communication Terminals

RF XCVR

RF Section