Energy Eye IR-05 Owner's Installation & Operations Manual

Energy Eye™ IR-05

Advanced Wireless RF PIR Motion Sensor

Installation & Operations Manual

For Use With:

EE-IR-05 Ceiling Mounted Wireless PIR Sensor

12/2006

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES AND INDUSTRY CANADA RSS REGULATIONS.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION

NOTICE: Changes or modificat ions not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the

device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure

requirements and void user’s authority to operate the device.

The term “IC:” before the radio certification number only signifies that Industry Canada Technical Specifications were met

1.0 IMPORTANT – PLEASE READ THIS SECTION FIRST

Please read through the important information below before getting started with the IR-05
WIRELESS CEILING MOUNTED PIR MOTION SENSOR

• Carefully follow the instructions in this manual when installing, setting up and
programming the IR-05 SENSOR. Failure to follow these directions and
recommendations may result in voiding your Limited Warranty

• Take special notice of any specified notes, bullet points, and so on throughout this
manual

• Please take the following precautionary measures while handling, using and
installing the IR-05 SENSOR:

1. Keep the SENSOR away from water or damp areas.

2. Do not install the SENSOR in direct sunlight or near extreme heat.

3. Do not install the SENSOR near strong electrical current or magnetic force.

4. Avoid dropping the SENSOR or placing it in an area with strong vibration.

5. Do not disassemble the product – Doing so will void the Limited Warranty.

6. USE ONLY APPROVED BATTERIES

7. The SENSOR should be installed by qualified personnel only.

8. The Energy Eye receiver and sensors contain sensitive electronic components, DO

NOT attempt to repair or clean with chemicals or abrasives.

9. Never remove components from their original packaging until you are ready for
installation. Doing so may cause damage that will VOID your Limited Warranty.

10. Be careful with any tools near or around your working/installation environment.

NOTE: The Manufacturer shall have no liability for any death, personal and/or bodily
injury and/or damage to property or other loss, whether direct, indirect, incidental,
consequential or otherwise, based on a claim that the Product failed to function.

1.1 Required Tools

• Philips Screwdrivers (various sizes)

• Flat head Screwdriver (small)

• Special Concrete Screws (Necessary ONLY for Mounting on a Concrete Surface)

• Tall ladder

NOTE: Additional tools might be required depending on property construction type,
local environment, accessibility etc…

1.2 Introduction

The Energy Eye IR-05 Wireless Ceiling Mounted PIR sensor has been created
using a proprietary design to appease the most discerning hotel operations. This Ceiling
mounted motion sensor features a wide coverage detection pattern to make sure that
guests are accurately detected within the room, even while in bed.

The special design has been created to replicate the standard smoke detector
found in hotel guestrooms. This design helps keep the Energy Management operation
discreet and reduces the incidence for guests discomfort or the possibility of confusing
the motion detector with a camera device.

This sensor has been designed with the same proprietary radio coding that is
found in other high quality Energy Eye wireless components and will not interfere with
other sensors or wireless devices within the guestroom. The sensor is designed solely
for use with the Energy Eye Controllers (EERX/EERXS) and does not function with any
other wireless components or security systems.

1.3 General Specifications

RF Transmitter 315 MHz
Voltage Input 4.4V ~ 6V
Current Draw (Sleep Mode) 115uA
Current (Transmit) 6mA
Transmission Range 30 Feet ~ 100 Feet
Transmission Encoding Internal IC w/ 4 Billion Combinations
Battery Specifications (2) X LiMn02 CR123A 1400mAH
Recommended Batteries Sanyo/Panasonic/Energizer
Calculated Battery Life 1 year @ 60 Tx/Hour
Dimensions (Diameter X
Height)

10.5 cm x 5 cm

Certifications FCC Part 15B, Industry Canada RSS