Energizer 10343-SS-10, 10343-GM-10, 10343-CO-10, 10343-BZ-10, 10343-BK-10 User Manual
10-PACK
SOLAR PATHWAY LIGHTS
MODEL # : 10343-CO-10 (COPPER) 10343-BZ-10 (BRONZE)
10343-GM-10 (GUNMETAL) 10343-SS-10 (STAINLESS STEEL)
10343-BK-10 (BLACK)
ASSEMBLY AND CARE INSTRUCTIONS
IMPORTANT: Retain for future reference. Read carefully.
Solar Top Housing x 10
A
B
Glass Lens x 10
C
Post x 10
D
Ground Stake x 10
Choosing the Right Location
Your solar lights should be installed in an area that gets DIRECT SUNLIGHT. Your
solar lights will produce more hours of operation when installed in an area which is
free from cover, shade or shadowing.
NOTE: If the ground is hard and packed, moisten the ground with water
before inserting the stake to avoid breakage.
How Solar Lights Work
Solar lights have a solar cell that converts sunlight into electricity. This electricity is
used to recharge the built-in battery each day. Since the solar lights are powered
entirely by the sunlight they receive each day, operating time will vary by specific
location, daily weather conditions, and season.
CARE AND USE
INSTRUCTIONS
For assistance with assembly or
installation, parts and customer
service, please call
1-800-711-1585
Monday thru Friday
9:00 AM to 5:00 PM (PST)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Assembly
Attaching the post to the ground stake
Remove inverted ground stake
stored inside the post.
Attach the post (C) to the ground stake (D)
by pushing the post (C) onto the top of the
ground stake (D).
Push the post-stake assembly into the ground.
CAUTION: The ground stake is sharp.
Be careful when handling to avoid injury.
Attaching the solar housing
Attach the solar top housing (A) on top of the glass lens (B) using a
clockwise twisting motion.
Removing the battery tab
If light is packaged with the solar top hat (A) attached to the glass (B),
remove using a counter-clockwise turning motion. If the solar top housing
is separate, proceed below.
Remove the battery tab from the battery compartment on the solar top
housing (A).
Made in China/Hecho en China/Fabriqué en Chine
A
N
a
n
e
d
i
2
t
h
a
0
e
r
1
e
r
9
A
u
E
l
s
p
n
e
a
e
d
n
r
g
u
L
i
n
z
i
g
d
e
h
r
e
.
t
r
i
n
l
i
c
g
E
e
n
P
n
e
r
s
r
o
g
e
d
i
b
z
u
e
y
c
t
A
s
l
,
p
I
a
n
c
.
n
o
11-800-7 1-1585
Use Rechargeable Battery Only
Sólo Use Batería Recargable
Utilisez La Pile Rechargeable Seulement
ANi-MH A 1.2V 800mAh
Manufacture Date : 11 / 2018
r
a
n
d
n
c
e
L
r
t
i
a
g
i
h
n
r
t
g
i
E
n
r
a
n
g
p
h
e
P
r
r
g
o
i
d
z
u
e
r
B
r
a
n
s
i
k
c
r
d
a
e
m
s
e
i
g
d
n
a
r
s
t
a
e
r
c
m
t
a
s
,
n
I
n
d
c
n
.
a
r
A
b
l
l
r
o
e
t
h
d
e
s
h
t
,
L
h
t
L
i
C
w
i
d
s
e
a
t
f
a
f
i
l
i
e
n
E
f
o
e
r
a
s
e
e
p
s
e
r
Remove Tab Before Use
Enlever Avant d'utiliser
Quitar La Lengueta Antes De Usar
C
L
L
,
s
d
h
t
n
f
a
r
o
B
s
r
f
k
e
r
o
z
a
i
s
g
m
r
r
e
e
d
n
a
r
w
t
o
e
v
i
t
c
s
e
i
r
a
i
d
i
s
.
b
s
u
r
s
e
n
d
e
w
t
o
a
l
e
e
v
r
.
i
t
s
d
c
k
n
e
r
a
a
p
s
m
e
e
r
d
r
i
a
e
r
t
r
i
e
h
t
Remove battery tab
Inserting the solar light assembly
Insert the solar light assembly on top of the post (C).
NOTE: Do not use a hammer.
If the ground is hard, use
water to soften.
C
IMPORTANT: Do not press down
on the solar panel on top of the
solar top housing (A). This can
damage the light.
© 2019 Energizer. Energizer and certain graphic designs are trademarks of Energizer Brands, LLC and related subsidiaries and are used under license by Alpan Lighting Products, Inc.
All other brand names are trademarks of their respective owners. Neither Alpan Lighting Products, Inc. nor Energizer Brands, LLC is affiliated with the respective owners of their trademarks.
Made in China
1
Care & Cleaning
Clean the solar panel with a damp cloth. Do not use any chemicals or abrasives.
Keep the solar panel free of snow and debris to allow the battery to charge
properly.
Battery Warnings
Do not use alkaline, standard (carbon-zinc) or Ni-Cd (nickel cadmium)
batteries in our solar lights.
Only use Nickel Metal Hydride rechargeable batteries (Includes 10
rechargeable batteries.)
Do not mix battery types. Only use Ni-MH (nickel metal hydride) batteries.
Adverse conditions of cold, extreme cold, extreme heat plus humidity and
dampness may affect battery performance.
Do not open, short circuit or mutilate batteries as injury may occur.
Batteries must be recycled or disposed of properly.
Always purchase the correct size and grade of battery most suitable for the
intended use.
Clean the battery contacts and also those of the device prior to battery
installation.
Ensure the batteries are installed correctly with regard to polarity (+ and -).
Remove batteries from equipment that will not be used for an extended period
of time.
Remove used batteries promptly.
R B R C
Ni-MH
CONTAINS NICKEL METAL HYDRIDE
RECHARGEABLE BATTERIES.
BATTERIES MUST BE RECYCLED
OR DISPOSED OF PROPERLY.
Maintenance
Replacing the battery
Remove the solar light assembly from
the post by gently pulling upwards.
Remove the solar top housing (A)
from the glass lens (B) using a
counter-clockwise twisting motion.
Remove the battery cover on the
bottom of the solar top housing (A)
and replace the battery.
Re-assemble the unit.
IMPORTANT: Use only
AA 800mAh Nickel Metal
Hydride (Ni-MH)
rechargeable batteries for
the solar lights. These are
available at most hardware
stores or through Alpan
Lighting Products at
1-800-711-1585.
Made in China/Hecho en China/Fabriqué en Chine
N
a
n
e
d
i
2
t
h
a
0
e
r
1
e
r
9
A
u
E
l
s
p
n
e
a
e
d
n
r
g
u
L
i
n
z
i
g
d
e
h
r
e
.
t
r
i
n
l
i
c
g
E
e
P
n
r
s
o
e
d
b
u
y
c
t
s
,
I
n
11-800-7 1-1585
Use Rechargeable Battery Only
Sólo Use Batería Recargable
Utilisez La Pile Rechargeable Seulement
ANi-MH A 1.2V 800mAh
Manufacture Date : 11 / 2018
n
e
r
g
i
z
e
r
A
a
l
n
p
d
a
c
n
c
e
.
L
r
n
t
i
a
g
o
i
n
h
r
t
g
i
E
n
r
a
n
g
p
h
e
P
i
c
r
r
d
g
o
e
s
i
d
i
g
a
z
n
r
t
s
e
a
u
r
e
c
t
r
s
,
B
I
n
c
r
.
A
a
b
l
r
l
e
o
h
t
n
d
s
,
L
L
C
d
i
s
e
t
a
a
f
i
f
l
i
Solar Top
Housing
s
e
i
r
a
i
d
i
s
.
b
s
u
r
s
e
n
d
e
w
t
o
a
l
e
e
v
r
.
i
t
s
d
c
k
n
e
r
a
a
p
s
C
m
e
L
e
r
L
d
r
i
,
a
e
s
r
t
h
d
t
r
n
i
f
a
e
r
o
h
B
t
s
r
f
k
r
e
o
z
a
i
s
g
m
r
r
e
e
e
n
d
n
E
a
r
f
w
t
o
o
e
s
r
k
e
r
a
a
v
m
i
s
e
t
d
e
c
m
e
a
n
p
d
s
n
a
e
r
r
e
h
t
h
t
i
w
Battery
Battery Cover
CAUTION: Do not dispose of battery in fire.
IMPORTANT: Dispose of the battery in accordance with
local, state and federal regulations.
Troubleshooting
Problem Solution
Light stops working after
period of working properly.
The lights only operate for a
short duration in the evening.
The battery is not adequately charged. Place the unit in direct sunlight for three sunny days.
The units are not getting sufficient sunlight. If the sunlight is blocked by a tree, house, or other objects, move the units
to a sunnier location. Note that lighting time will be shorter on overcast days.
The light level is too high for the solar lights to turn on. The solar lights are designed to turn on when it is dark outside.
Make sure the solar top housing is not under any direct light source when testing.
The battery may be weak or can no longer produce a charge. Replace the battery.
The units are not getting sufficient sunlight. If the sunlight is blocked by a tree, house, or other objects, move the units to
a sunnier location. Note that lighting time will be shorter on overcast days.
The battery may be weak or can no longer produce a charge. Replace the battery.
Two Year Limited Warranty
Alpan Lighting Products, Inc. warrants this product to be free for two (2) years against any defects that are due to faulty materials or workmanship. Alpan Lighting Products, Inc. shall promptly correct such
defects by repair or replacement, at its option. This warranty covers only product defects and shall expire two years after the date of purchase by the original purchaser. Proof of Purchase (Sales Receipt) is
required.
This warranty does not apply to (1) bulbs and batteries or (2) defects caused by and resulting from misuse, neglect, accident or improper operation, maintenance, storage, transportation handling of the
product. The warranty does not cover any transportation costs for return of the product or for reshipment of any repaired or replaced product, or cost associated with installation, removal or reinstallation of
the product. This warranty extends to the original purchaser only and is not transferable or assignable to subsequent purchasers. This warranty does not cover surface scratches, weathering, or natural aging
to the patina of fixture finishes as this is considered normal wear.
Alpan Lighting Products, Inc. shall have no responsibility for damage to persons or property or other loss or injury resulting from a defect in the product or from improper use or installation. UNDER NO
CIRCUMSTANCES SHALL ALPAN BE LIABLE SPECIAL OR CONSEQUENTIAL DAMAGES. ANY WARRANTIES IMPLIED BY LAW, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO TWO YEARS AFTER THE DATE OF THE ORIGINAL PURCHASE. In no event shall Alpan Lighting Product, Inc.’s liability under this warranty exceed
the cost of repair or replacing such defective product, and Alpan’s maximum liability under any warranty is in lieu of all other warranties expressed or implied.
Some states do not allow the exclusion or limitation of special or consequential damages or allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This
warranty gives you specific legal rights, and you may have rights that vary from state to state. If you feel you have a claim under this warranty, contact consumer service for advice on handling the claim.
Written notice of any defects must be given to Alpan Lighting Products, Inc. upon discovery.
Problem Solving
Made in China
2
Loading...