Energer ENB569DRL Safety And Operating Manual
SAFETY AND OPERATING MANUAL
Original Instructions 1 .0
750W ROTARY HAMMER ENB569DRL
Read all safety warnings and all instructions before use. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.
750W ROTARY HAMMER ENB569DRL
SPEICIAL WARNING FOR HAMMER
CAUTION
This is a very powerful Drill.
When using this drill it is essential that the following rules for use are followed!
1. When drilling it is common that the core / drill bit jams in the material being drilled. This will result
in the drill trying to rotate around the drill bit and potentially come out of your grip. This SDS Drill has
a safety clutch mechanism. This safety clutch mechanism will be activated and stop the drive to the
drill bit BUT only if you resist the initial forces caused by the jamming by securely holding the drill
with both hands. As this is a very powerful drill these forces are significant.
2. ALWAYS ensure that the front handle is firmly affixed and secure.
3. The Front and rear handle must be firmly held to resist any movement of the drill when the core
or drill
drill
4. ALWAYS use this drill when standing on a firm and secure platform or the ground. (DO NOT USE
ON LADDERS OR STEPS)
5. NEVER Start the Drill with the core or drill jammed in position.
6. DO NOT stretch to hold the drill. Do not drill above shoulder height or below Knee height, as the
drill cannot be securely held.
7. Never drill holes that are above the declared maximum size in the manual.
bit becomes jammed.
GENERAL SAFETY INSTRUCTIONS
WARNING. Read all safety warnings and instructions.
Failing to follow the warnings and instructions can result in an electric shock, a fire
and/or a serious injury.
Keep all warnings and all instructions to be able to refer to them later on.
The term “tool” in the warnings refers to your electrical mains powered tool (with power cord) or your battery
operated tool (without power cord).
1 Safety of the work area
a) Keep the work area clean and well lit. Cluttered and dark areas invite accidents.
b) Do not operate electric tools in explosive atmospheres, for example in the presence of flammable
liquids, gases or dust. Electric tools create sparks that can ignite the dust or fumes.
c) Keep children and bystanders away while operating the tool. Distractions can cause you to
of the tool.
2 Electrical safety
a) The electric tool plugs must match the outlet. Never modify the plug in any way. Do not use
adapters with earthed (grounded) tools. Unmodified plugs and matching outlets will reduce the risk of
electric shock.
b) Avoid any body contact with earthed or grounded surfaces such as pipes, radiators, cookers and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose tools to rain or wet conditions. Water entering a tool will increase the risk of electrical
shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the tool. Keep the
cord away from heat, lubricants, edges and moving parts. Damaged or entangled c
of electric shock.
e) When using a tool outside, use an extension cable suitable for outside use. Use of a cord suitable for
outside use reduces the risk of electric shock.
f) If use of a tool in a humid location is unavoidable, use a supply protected by a residual current
differential device (RCD). The use of an RCD reduces the risk of electric shock.
ords incre
control
lose
ase the risk
750W ROTARY HAMMER ENB569DRL
3 Personal safety
a) Stay alert, watch what you are doing and use common sense when operating the tool. Do not use
the tool when you are tired or under the influence of drugs, alcohol or medication. One moment of
carelessness while using a tool can result in serious personal injury.
b) Use safety equipment. Always wear eye protection. Safety equipment such as dust masks, non-slip
safety shoes, a hard hat and hearing protection used for appropriate conditions will reduce personal injuries.
c) Avoid unintentional starting. Make sure that the switch is in the off position before plugging the tool
into the mains and/or fitting the batteries, picking it up or carrying it. Carrying tools with your finger on
the switch or plugging in tools with the
d) Remove any adjustment key before operating the tool. A key left attached to a rotating part of the tool
can result in personal injury.
e) Do not overreach. Keep a proper position and balance at all times. This enables better control of the
tool in unexpected situations.
f) Dress in a suitable manner. Do not wear loose clothing or jewellery. Keep hair, clothing and gloves
away from moving parts. Loose clothing, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection equipment, make sure
that they are connected and used correctly. Using dust collectors can reduce the dust-related risks.
4 Use and maintenance of the tool
not force
a) Do
and safer in the conditions for which it was manufactured.
b) Do not use the tool if the switch does not make it possible to change from the operating condition to
stop and vice versa. Any tool which cannot be controlled by the switch is dangerous and should be repaired.
c) Disconnect the power cord before any adjustment, changing an accessory or before storing the
tool. Such preventive safety measures reduce the risk of starting the tool accidentally.
d) Keep idle tools out of the reach of children and do not allow persons unfamiliar with the tool or
these instructions to operate it. Tools are dangerous in the hands of untrained users.
e) Maintain the
parts or any other condition that could affect the operation of the tool. In the event of damage, have
the tool repaired before using it. Many accidents are due to badly maintained tools.
f) Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to
bind and are easier to control.
g) Use the tool, accessories and blades etc., in accordance with these instructions, while taking into
account the work conditions and the work to be done. The use of the tool for operations other than those
intended could result in dangerous situations.
the tool. Use the correct tool for your application. The correct tool will do the work better
tool. Check that there is no
switch in
the on position is a cause of accidents.
misalignment or obstruction of the moving parts, broken
5)Service
a) Have your power tool serviced by a qualified repair person using onl
This will
ensure that the safety of the power tool is maintained.
SPECIAL SAFETY INSTRUCTIONS
1.Wear ear protectors. Exposure to noise can cause hearing loss.
2.Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
3.Hold power tool by insulated gripping surfaces, when performing an operation where the cutting
accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could give the operator an electric shock.
4. Do not use the drill near water.
5. Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.
6. Fully unwind extension cords to avoid potential overheating.
7. When an extension cord is requir
that it is in a safe electrical condition.
8. Ensure the supply voltage is same as rating voltage.
9. The tool is double insulated for additional protection against a possible electrical insulation failure within the
tool.
10. Always check walls and ceilings to avoid hidden power cables and pipes.
750W ROTARY HAMMER ENB569DRL
ed, please ensure it has the correct ampe
y identical replacement parts.
re rating for the power tool and
11. After long working periods, external metal parts and accessories could be hot.
12. Wear eye protection when operating this tool.
ADDITIONAL SAFETY WARNING FOR CONSTRUCTION DUST
The updated Control of Substances Hazardous to Health Regulations 1st October 2012 now also targets to
reduce the risks associated with silica, wood and gypsum dusts.
Construction workers are one of the at-risk groups within this because of the dust that they breathe: silica dust
is not just a nuisance; it is a real risk to your lungs!
Silica is a natural mineral present in large amounts in things like sand, sandstone and granite. It is also
commonly found in many construction materials such as concrete and mortar. The silica is broken into very fine
dust (also known as Respirable Crystalline Silica or RCS) during many common tasks such as cutting, drilling
and grinding
Breathing in very fine particles of crystalline silica can lead to the development of:
Lung cancer
Silicosis
Chronic Obstructive Pulmonary Disorder (Chronic obstructive pulmonary disease (COPD))
And breathing in fine particles of wood dust can lead to the development of Asthma
The risk of lung disease is linked to people who regularly breathe construction dust over a period of time, not
on the odd occasion.
To protect the lung, the COSHH Regulations sets a limit on the amount of these dusts that you can breathe
(called a Workplace Exposure Limit or WEL) when averaged over a normal working day. These limits are not a
large amount of dust: when compared to a penny it is tiny – like a small pinch of salt:
This limit is the legal maximum; the most you can breathe after the right controls have been used.
How to reduce the amount of dust?
1 Reduce the amount of cutting by using the best sizes of building products.
2 Use a less powerful tool e.g. a block cutter instead of angle grinder.
3 Using a different method of work altogether – e.g. using a nail gun to direct fasten cable trays instead of
drilling holes first.
Please always work with approved safety equipment, such as those dust masks that specially designed to filter
out microscopic particles and use the dust extraction facility at all time.
For more information please see the HSE website:
http://www.hse.gov.uk/construction or http://www.hse.gov.uk/pubns/cis69.pdf
Warning: Some dust particles created by power sanding, sawing, grinding, drill
and other construction jobs contain chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
Lead from lead-based paints.
Crystalline silica from bricks and cement and other masonry products.
Arsenic and chromium from chemically treated timber.
Your risk from these exposures varies, depending upon how often you do this type of work. To
reduce your exposure to these chemicals:
Work in a well-ventilated area.
Work with approved safety equipment, such as those dust masks that are specially designed
to filter microscopic particles.
750W ROTARY HAMMER ENB569DRL
NOISE INFORMATION
Wear hearing protection!
Measured sound values determined according to EN 60745.
The noise figures quoted are emission levels and are not necessarily safe working levels. Whilst there is a
correlation between the emission and exposure levels, this cannot be used reliably to determine whether or
not further precautions are required. Factors that influence the actual level of exposure of work-force include
the characteristics of the work room, the other sources of noise, etc. i.e. the number of machines and other
adjacent processes, and the length of time for which an operator is exposed to the noise. Also the permissible
exposure level can vary from country. This information, however, will enable the user of the machine to make a
better evaluation of the hazard and risk.
VIBRATION
The European Physical Agents (Vibration) Directive has been brought in to help reduce hand arm vibration
syndrome injuries to power tool users. The directive requires power tool manufacturers and suppliers to
provide indicative vibration test results to enable users to make informed decisions as to the period of time a
power tool can be used safely on a daily basis and the choice of tool.
Further advice can be found at www.hse.gov.uk
Vibration total values (triax vector sum) determined according to EN 60745:
Hammer drilling into concrete (For main
handle)
Chiseling(For main handle)
Hammer drilling into concrete (For auxiliary
handle)
Chiseling(For auxiliary handle)
Vibration emission value a
Uncertainty K = 1.5 m/s
2
Vibration emission value a
Uncertainty K = 1.5 m/s
2
Vibration emission value a
Uncertainty K = 1.5 m/s
2
Vibration emission value a
Uncertainty K = 1.5 m/s
2
=15.810m/s
h,HD
= 15.668 m/s
h,Cheq
=14.092 m/s
h,HD
= 13.090 m/s
h,Cheq
2
2
2
2
The declared vibration emission value should be used as a minimum level and should be used with the current
guidance on vibration.
The declared vibration emission been measured in accordance with a standardised test stated above and may
be used to compare one tool with another tool.The declared vibration emission value may also be used in a
preliminary assessment of exposure.
WARNING!
The vibration emission value during actual use of the power tool can differ from the declared value depending
on the ways in which the tool is used dependent on the following examples and other variations on how the
tool is used:
How the tool is being used and the materials being cut or drilled.
The tool being in good condition and well maintained
The use the correct accessory for
the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles.
And the tool is being used as intended by its design and these instructions.
While working with this power tool, hand/arm vibrations occur. Adopt the correct working practices in order to
reduce the exposure to vibration.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
750W ROTARY HAMMER ENB569DRL
Loading...