Energer ENB522TCB Original Instructions Manual
Original instructions : MNL_ENB522TCB_V1
450W Tile Cutter
ENB522TCB
Barcode: 5052931248223
WARNING! Read the instructions before using the product!
02
03
ENB522TCB by Energer
Let’s
These instructions are for your safety. Please read through them thoroughly
before use and retain them for future reference.
Getting started...
In more detail...
Your product
Technical and legal information
Before you start
Product functions
Care and maintenance
Trouble shooting
Guarantee
EC declaration of conformity
get started...
03
04
05
14
15
Operation
16
18
19
Recycling and disposal
19
20
21
GB
IE
10
Thank you for choosing a product it will give you full satisfaction in your
craft in the work.
The band saw is a product easy to use, it comes with accessories. For best use,
you must read this noice. It will provide key information on the functions of the device
and the rules to follow for maintenance.
Please keep this manual for future reference later.
04
05
ENB522TCB by Energer ENB522TCB by Energer
Technical and legal
information
Your product
Your product
GB
IE
Getting started...
GB
IE
Getting started...
Technical data
7. Extension table
8. Fixing knob
9. Fixing knob
5. On/Off switch
6. Carry handle
1. Parallel cutting guide
2. Angle cutting guide
3. Wheel guard
4. Water reservoir lid
1
2
3
4
5
6
7
> Voltage/Frequency: 230-240V~ 50Hz
> Motor Power: 450W, S2:30min
> No-Load Speed: 5400/min
Blade size: ø110mm (D) - Bore ø22.23mm
Max. Cutting Thickness: To 90°:23mm – to 45°:16mm
Protection Degree (IP):
IP23
A weighted sound pressure KpA: 93dB(A)
Table size (Unextended ~ Extended): 332 ~ 395mm (L) x 305mm (W)
Weight: 3.7kg
>
>
>
>
> Uncertainty KpA: 3dB
>
>
A load factor of S2 30 min ( temporary duty ) means that you may operate
the motor continuously at its nominal power level (450W) for no longer than
the time stipulated on the specifications label (30minutes ON period). If you
fail to observe this time limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
> A weighted sound power KwA: 106dB(A)
> Uncertainty KwA: 3dB
８
９
> Vibration level: 2.5 m/s2
> Uncertainty K: 1.5m/s
2
Noise and Vibration Data
The declared vibration total value has been measured in accordance with a
standard test method and may be used for comparing one tool with another.
The declared vibration total value may also be used in a preliminary assessment
of exposure.WARNING: The vibration emission during actual use of the power
tool can differ from the declared total value depending on the ways in which the
tool is used. The need to identify safety measures and to protect the operator
are based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle, such as the times the tool is switched
off, when it is running idle, in addition to trigger time).
Getting
FR
IE
Getting started...
06 07
GB
IE
GB
IE
Getting started...
Getting started...
ENB539TAS by Energer ENB539TAS by Energer
Technical and legal
information
Technical and legal
information
Symbols
Read the instruction manual.
Wear respiratory protection.
Warning! Denotes risk of personal injury, loss of life, or damage
to the tool in case of non-observance
Wear protective gloves
The product complies with the applicable European directives
and an evaluation method of
conformity for this directives
was done.
Caution,risk of cutting.
yyWxx: Manufacturing date code; year of manufacturing (20yy)
and week of manufacturing (Wxx)
Wear ear protection.
Wear eye protection.
Switch the product off and disconnect it from the power
supply before assembly, cleaning, adjustments,
maintenance, storage and transportation.
General safety
WARNING: When using electric tools basic safety
precautions should always be followed to reduce the risk
of fire, electric shock and personal injury including the
following. Read all these instructions before attempting
to operate this product and save these instructions.
1 Keep work area clear
> Cluttered areas and benches invite injuries.
2 Consider work area environment
> Do not expose tools to rain.
> Do not use tools in damp or wet locations.
> Keep work area well lit.
> Do not use tools in the presence of flammable liquids or gases.
3 Guard against electric shock
> Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators,
ranges, refrigerators).
4 Keep other persons away
> Do not let persons, especially children, not involved in the work touch the tool
or the extension cord and keep them away from the work area.
5 Store idle tools
> When not in use, tools should be stored in a dry locked-up place, out of reach
of children.
6 Do not force the tool
> It will do the job better and safer at the rate for which it was intended.
7 Use the right tool
> Do not force small
tools to do the job of a heavy duty tool. Do not use tools for
purposes not intended; for example do not use circular saws to cut tree limbs
or logs.
8 Dress properly
> Do not wear loose clothing or jewellery, they can be caught in moving parts.
> Non-skid footwear is recommended when working outdoors.
> Wear protective hair covering to contain long hair.
9 Use protective equipment
> Use safety glasses.
> Use face or dust mask if working operations create.
10 Connect dust extraction equipment
> If the tool is provided for the connection of dust extraction and collecting equipment,
ensure these are connected and properly used.
IP23: Degree of protection provided by enclosure.
Use correct size of blades.
Do not use segmented blade.
Wet cut only.
Loading...