Energer ENB467HTG Safety And Operating Manual

SAFETY AND OPERATING MANUAL

Original Instructions 5.0

2000W HEAT GUN

ENB467HTG

Read all safety warnings and all instructions before use. Failure to follow the
warnings and instructions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference.

2000W HEAT GUN

ENB467HTG

GENERAL SAFETY INSTRUCTIONS

This appliance is not intended for use by persons (including children) with reduced physical, sen sory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

CAUTION!

If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in
order to avoid a safety hazard.

SPECIAL SAFETY INSTRUCTIONS

This product is not designed for industrial or trade applications. Do not use the appliance to perform
applications for which it is not designed.

1.A fire may result if the appliance is not used with care, therefore :

- be careful when using the appliance in places where there are combustible material s;

- do not apply to the same place for a long time;

- do not use in presence of an explosive atmosphere;

- be aware that heat may be conducted to combustible materials that are out of sight;

- place the appliance on its stand after use and allow if to cool down before storage;

- do not leave the appliance unattended when it is switched on.

2. Do not point the hot air steam at people or animals.

3. Do not touch the hot nozzle. Wear protective gloves.

4. Ensure that in all cases that the unit is completely cooled before storing.

5. Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.

6. Fully unwind extension cords to avoid potential overheating.

7.When an extension cord is required, please ensure it has the correct ampere rating for the power tool an d
that it is in a safe electrical condition.

8. Ensure the supply voltage is same as rating voltage.

9. The tool is double insulated for additional protection against a possible electrical insulation failure within
the tool.

2000W HEAT GUN

ENB467HTG

Emergency

Familiarise yourself with the use of this product by means of this instruction manual. Memorise the
safety directions and follow them to the letter. This will help to prevent risks and hazards.

1.Always be alert when using this product, so that you can recognise and handle risks early. Fast intervention
can prevent serious injury and damage to property.

2.Switch off and disconnect from the power supply if there is any malfunction. Have the product checked by a
qualified specialist and repaired, if necessary, before you put it into operation again.

Residual risks

Even if you are operating this product in accordance with all the safety requirements, potential risks of injury
and damage remain. The following dangers can arise in connection with the structure and design of this
product:

1. Health defects resulting from vibration emission if the product is being used over long perio ds of time or not
adequately managed and properly maintained.

2. Injuries and damage to property due to broken application tools or the sudden impact of hidden objects
during use.

3. Danger of injury and property damage caused by flying objects.

WARNING!

This product produces an electromagnetic field during operation! This field may under some circumstances
interfere with active or passive medical implants! To reduce the risk of serious or fatal injury, we recommend
persons with medical implants to consult their doctor and the medical implant manufacturer before ope rating
this product!

Important note

Be sure the supply is the same as the voltage given on the rating plate. Remove the mains plug before
carrying out any adjustment or servicing.

Intended use

The unit is intended for the forming and welding of plastic, removal of paint an d the warming of heat sh rinkable
tubing. It is also suitable for soldering and tinning, loosening of adhesive joints and the defrosting of water
lines.

2000W HEAT GUN

ENB467HTG

SYMBOLS

The symbols shown on the product has great significance for the safe use of the product.

WARNING - To reduce the risk of injury, user must read the instruction manual

Double insulation Class II

Conforms to all relevant safety standards.

Wear respiratory protection
Wear safety gloves

yyWxx Manufacturing date code:
Year of manufacturing (20yy) and week of manufacturing (Wxx);

2000W HEAT GUN

ENB467HTG