Eneo DLR-2104/1.0TBV, DLR-2108/1.0TBV Operating Instructions Manual
Operating Instructions
Digital Video Recorder, H.264
Models: DLR-2104/1.0TBV (4-Channel)
Models: DLR-2108/1.0TBV (8-Channel)
Digital Video Recorder
i
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated "dangerous voltage" within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the literature accompanying
the appliance.
COMPLIANCE NOTICE OF FCC:
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL
DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE
REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN
A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO
FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION
MANUAL, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS
EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE, IN WHICH CASE
USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR
COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE-
CAUSING EQUIPMENT REGULATIONS.
The information in this manual is believed to be accurate as of the date of publication. We are not responsible for any
problems resulting from the use thereof. The information contained herein is subject to change without notice. Revisions
or new editions to this publication may be issued to incorporate such changes.
The software included in this product contains some Open Sources. You may obtain the complete corresponding source
code from us. See the Open Source Guide on the software CD (OpenSourceGuide\OpenSourceGuide.pdf) or as a printed
document included along with the User's Manual.
User’s Manual
ii
Important Safeguards
1. Read Instructions
All the safety and operating instructions should be read before the
appliance is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future
reference.
3. Cleaning
Unplug this equipment from the wall outlet before cleaning it. Do
not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
4. Attachments
Never add any attachments and/or equipment without the approval
of the manufacturer as such additions may result in the risk of fire,
electric shock or other personal injury.
5. Water and/or Moisture
Do not use this equipment near water or in contact with water.
6. Placement and Accessories
Do not place this equipment on an unstable cart, stand or table. The
equipment may fall, causing serious injury to a child or adult, and
serious damage to the equipment.
This equipment and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the
equipment and cart combination to overturn.
Do not place this equipment on a closed space. Sufficient amount of
ventilation air is necessary to avoid increase of ambient temperature
which can cause improper operation or the risk of fire.
7. Power Sources
This equipment should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power,
please consult your equipment dealer or local power company.
8. Power Cords
Operator or installer must remove power and TNT connections before
handling the equipment.
9. Lightning
For added protection for this equipment during a lightning storm, or
when it is left unattended and unused for long periods of time, unplug
it from the wall outlet and disconnect the antenna or cable system. This
will prevent damage to the equipment due to lightning and
power-line surges.
10. Overloading
Do not overload wall outlets and extension cords as this can result
in the risk of fire or electric shock.
11. Objects and Liquids
Never push objects of any kind through openings of this equipment
as they may touch dangerous voltage points or short out parts that
could result in a fire or electric shock. Never spill liquid of any kind
on the equipment.
12. Servicing
Do not attempt to service this equipment yourself. Refer all servicing
to qualified service personnel.
13. Damage requiring Service
Unplug this equipment from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have fallen into the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the operating
instructions, adjust only those controls that are covered by the
operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a
qualified technician to restore the equipment to its normal operation.
E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance –
this indicates a need for service.
14. Replacement Parts
When replacement parts are required, be sure the service technician
has used replacement parts specified by the manufacturer or that have
the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
15. Safety Check
Upon completion of any service or repairs to this equipment, ask the
service technician to perform safety checks to determine that the
equipment is in proper operating condition.
16. Field Installation
This installation should be made by a qualified service person and
should conform to all local codes.
17. Correct Batteries
Warning: Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions.
18. Tmra
A manufacturer’s maximum recommended ambient temperature (Tmra)
for the equipment must be specified so that the customer and installer
may determine a suitable maximum operating environment for the
equipment.
WEEE (Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at
the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal,
please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product
should not be mixed with other commercial wastes for disposal.
Digital Video Recorder
iii
Table of Contents
Chapter 1 — Introduction ........................................................................................................... 1
Feature ................................................................................................................................... 1
Technical Overview ................................................................................................................ 1
Chapter 2 — Installation ............................................................................................................. 3
Package Contents .................................................................................................................. 3
Required Installation Tools .................................................................................................... 3
Video Input......................................................................................................................... 3
Alarm Input/Output ............................................................................................................ 3
RS485 Port ........................................................................................................................ 4
RS232 Port ........................................................................................................................ 4
Network Port ...................................................................................................................... 4
Video Out ........................................................................................................................... 5
Factory Reset Switch ......................................................................................................... 5
Power Cord Connector ...................................................................................................... 5
Chapter 3 — Configuration ........................................................................................................ 7
Front Panel Controls .............................................................................................................. 7
Camera Buttons ................................................................................................................. 7
HDD LED ........................................................................................................................... 7
Alarm LED ......................................................................................................................... 7
Arrow Buttons .................................................................................................................... 8
Play/Pause Button ............................................................................................................. 8
Menu Button ...................................................................................................................... 8
PTZ/Zoom Button .............................................................................................................. 8
Panic Button ...................................................................................................................... 8
Search Button .................................................................................................................... 9
USB Port ............................................................................................................................ 9
Remote Control Buttons......................................................................................................... 9
ID Button .......................................................................................................................... 10
Camera Buttons ............................................................................................................... 10
Sequence Button ............................................................................................................. 10
Freeze Button .................................................................................................................. 10
Arrow Buttons .................................................................................................................. 10
Menu Button .................................................................................................................... 10
Playback Buttons ............................................................................................................. 10
Panic Button .................................................................................................................... 10
Layout Button .................................................................................................................. 11
Zoom Button .................................................................................................................... 11
PTZ Button....................................................................................................................... 11
Enter Button ..................................................................................................................... 11
Alarm Button .................................................................................................................... 11
PTZ Control Button .......................................................................................................... 11
Backup Button ................................................................................................................. 11
Calendar Button ............................................................................................................... 11
Turning on the Power ........................................................................................................... 11
Initial Unit Setup ................................................................................................................... 11
Setup Screen ....................................................................................................................... 12
User’s Manual
iv
System Setup ....................................................................................................................... 13
General ............................................................................................................................ 13
Date/Time ........................................................................................................................ 20
User ................................................................................................................................. 22
Storage ............................................................................................................................ 24
System Event .................................................................................................................. 25
Recording Setup .................................................................................................................. 26
General ............................................................................................................................ 26
Schedule .......................................................................................................................... 27
Pre-Event ......................................................................................................................... 29
Event Setup ......................................................................................................................... 30
Motion .............................................................................................................................. 30
Alarm-In ........................................................................................................................... 31
Video Loss ....................................................................................................................... 32
Video Blind....................................................................................................................... 32
Text-In .............................................................................................................................. 33
Camera Setup ...................................................................................................................... 35
General ............................................................................................................................ 35
PTZ .................................................................................................................................. 36
Device Setup ........................................................................................................................ 37
Alarm-Out ........................................................................................................................ 37
Remote Control ............................................................................................................... 38
Network Setup ..................................................................................................................... 38
General ............................................................................................................................ 38
LAN .................................................................................................................................. 39
FEN .................................................................................................................................. 41
RTSP ............................................................................................................................... 42
WebGuard ....................................................................................................................... 43
VNC ................................................................................................................................. 43
Notification Setup ................................................................................................................. 44
Callback ........................................................................................................................... 44
Mail .................................................................................................................................. 45
SNS ................................................................................................................................. 47
Schedule .......................................................................................................................... 47
Display Setup ....................................................................................................................... 48
OSD ................................................................................................................................. 48
Main Monitor .................................................................................................................... 49
Chapter 4 — Operation ............................................................................................................ 51
Turning on the Power ........................................................................................................... 51
Live Monitoring ..................................................................................................................... 51
Live Monitoring Menu ...................................................................................................... 52
Active Cameo Mode ........................................................................................................ 54
Zoom Mode...................................................................................................................... 54
PTZ Mode ........................................................................................................................ 54
Event Monitoring .............................................................................................................. 55
Covert Camera ................................................................................................................ 55
Status Monitoring ............................................................................................................. 56
Recording Video .................................................................................................................. 57
Panic Recording .............................................................................................................. 57
Playing Recorded Video ...................................................................................................... 58
Digital Video Recorder
v
Searching Video ................................................................................................................... 59
Search Menu ................................................................................................................... 59
Event Log Search ............................................................................................................ 61
Record Table Search ....................................................................................................... 63
Motion Search ................................................................................................................. 64
Text-In Search ................................................................................................................. 66
Bookmarks ....................................................................................................................... 67
Clip-Copy ......................................................................................................................... 68
Print ................................................................................................................................. 69
Appendix .................................................................................................................................. 71
USB Hard Disk Drive Preparation ........................................................................................ 71
Text-In Search Examples..................................................................................................... 71
Search Example I ............................................................................................................ 71
Search Example II ........................................................................................................... 72
WebGuard ............................................................................................................................ 73
Web Monitoring Mode ..................................................................................................... 74
Web Search Mode ........................................................................................................... 75
Time Overlap ....................................................................................................................... 76
System Log Notices ............................................................................................................. 77
Error Code Notices .............................................................................................................. 78
Map of Screens .................................................................................................................... 79
Troubleshooting ................................................................................................................... 80
Specifications ....................................................................................................................... 80
List of Illustrations
Figure 1: Typical DVR installation. ............................................................................................................ 2
Figure 2: 8-Channel DVR rear panel. ........................................................................................................ 3
Figure 3: 8-Channel DVR front panel. ....................................................................................................... 7
Figure 4: Infrared remote control. .............................................................................................................. 9
Figure 5: Login screen. ........................................................................................................................... 12
Figure 6: Logout screen. ......................................................................................................................... 12
Figure 7: Setup screen. ........................................................................................................................... 12
Figure 8: System – General setup screen. .............................................................................................. 13
Figure 9: System – Date/Time setup screen. .......................................................................................... 20
Figure 10: System – User setup screen. ................................................................................................. 22
Figure 11: System – Storage setup screen. ............................................................................................ 24
Figure 12: System – System Event setup screen. .................................................................................. 25
Figure 13: Record – General setup screen. ............................................................................................ 26
Figure 14: Record – Schedule setup screen. .......................................................................................... 27
Figure 15: Schedule – Settings (Advanced Mode) setup screen. ........................................................... 28
Figure 16: Record – Pre-Event setup screen. ......................................................................................... 29
Figure 17: Event – Motion setup screen.................................................................................................. 30
Figure 18: Event – Alarm-In setup screen. .............................................................................................. 31
Figure 19: Event – Video Loss setup screen. .......................................................................................... 32
Figure 20: Event – Video Blind setup screen. ......................................................................................... 32
Figure 21: Event – Text-In setup screen. ................................................................................................ 33
Figure 22: Camera – General setup screen. ........................................................................................... 35
Figure 23: Camera – PTZ setup screen. ................................................................................................. 36
User’s Manual
vi
Figure 24: Device – Alarm-Out setup screen. ......................................................................................... 37
Figure 25: Device – Remote Control setup screen. ................................................................................ 38
Figure 26: Network – General setup screen. ........................................................................................... 38
Figure 27: Network – LAN setup screen. ................................................................................................ 39
Figure 28: Network – FEN setup screen. ................................................................................................ 41
Figure 29: Network – RTSP setup screen. .............................................................................................. 42
Figure 30: Network – WebGuard setup screen. ...................................................................................... 43
Figure 31: Network – VNC setup screen. ................................................................................................ 43
Figure 32: Notification – Callback setup screen. ..................................................................................... 44
Figure 33: Notification – Mail setup screen. ............................................................................................ 45
Figure 34: Notification – SNS setup screen. ........................................................................................... 47
Figure 35: Notification – Schedule setup screen. .................................................................................... 47
Figure 36: Display – OSD setup screen. ................................................................................................. 48
Figure 37: Display – Main Monitor setup screen. .................................................................................... 49
Figure 38: Live Monitoring menu. ............................................................................................................ 51
Figure 39: PTZ Select Camera menu. ...........................................................................................
......... 54
Figure 40: PTZ Preset menu. .................................................................................................................. 54
Figure 41: Event Status – Event Status screen. ...................................................................................... 56
Figure 42: Event Status – Storage screen. ............................................................................................. 57
Figure 43: Select Playback Camera menu. ............................................................................................. 58
Figure 44: Search menu. ......................................................................................................................... 59
Figure 45: Event Log Search screen. ...................................................................................................... 61
Figure 46: Record Table Search screen. ................................................................................................ 63
Figure 47: Motion Search screen. ........................................................................................................... 64
Figure 48: Text-In Search screen. ........................................................................................................... 66
Figure 49: Bookmarks screen. ................................................................................................................ 67
Figure 50: Clip-Copy screen. .................................................................................................................. 68
Figure 51: Print screen. ........................................................................................................................... 70
Digital Video Recorder
1
Chapter 1 — Introduction
Feature
Your color digital video recorder (DVR) provides recording capabilities for four or eight camera inputs. It provides
exceptional picture quality in both live and playback modes, and offers the following features:
4 or 8 Composite Video Input Connectors
Compatible with Color (NTSC or PAL) and B&W (CCIR and EIA-170) Video Sources
Auto Detection for NTSC and PAL
H.264 Codec
Monitor Connectors: 1 HDMI, 1 VGA
Multiple Search Engines (Date/Time, Calendar, Record Table, Event)
Real-time Recording (240/200 Images per Second (NTSC/PAL) with Very High (D1) Resolution)
Continuous Recording in Disk Overwrite Mode
2 USB 2.0 Ports
Continues Recording while Transmitting to Remote Site and during Playback
User-friendly Graphical User Interface (GUI) Menu System
Multiple Recording Modes (Time-lapse, Pre-event, Alarm, Motion and Panic)
Text Input for ATM and POS
Alarm Connections Include: Input and Output
Built-in Alarm Buzzer
Live or Recorded Video Access via Ethernet
Time Synchronization using industry standard protocol
IR Remote Control
Self-diagnostics with automatic notification including hard disk drive S.M.A.R.T. protocol
Technical Overview
In addition to replacing both a time-lapse VCR and a multiplexer in a security installation, your DVR has many features
that make it much more powerful and easier to use than even the most advanced VCR.
The DVR converts analog NTSC or PAL video to digital images and records them on a hard disk drive. Using a hard
disk drive allows you to access recorded video almost instantaneously; there is no need to rewind tape. The technology
also allows you to view recorded video while the DVR continues recording video.
Digitally recorded video has several advantages over analog video recorded on tape. There is no need to adjust tracking.
You can freeze frames, fast forward, fast reverse, slow forward and slow reverse without image streaking or tearing.
Digital video can be indexed by time or events, and you can instantly view video after selecting the time or event.
Your DVR can be set up for event or time-lapse recording. You can define times to record, and the schedule can change
for different days of the week and user defined holidays.
The DVR can be set up to alert you when the hard disk drive is full, or it can be set to record over the oldest video once
the disk is full.
Your DVR uses a proprietary encryption scheme making it nearly impossible to alter video.
You can view video and control your DVR remotely by connecting via Ethernet. There are two USB ports that can
be used to upgrade the system or copy video clips to external hard disk and flash drives.
User’s Manual
2
Figure 1: Typical DVR installation.
NOTE: This manual covers the 4- and 8-channel digital video recorders. The DVRs are identical except for the
number of cameras and alarms that can be connected and the number of cameras that can be displayed.
For simplicity, the illustrations and descriptions in this manual refer to the 16-camera model.
Digital Video Recorder
3
Chapter 2 — Installation
Package Contents
The package contains the following:
Digital Video Recorder
Power Adaptor and Power Cord
User’s Manual (This Document)
RAS Software CD and User’s Manual
Infrared Remote Control
Required Installation Tools
No special tools are required to install the DVR. Refer to the installation manuals for the other items that make up part
of your system.
Figure 2: 8-Channel DVR rear panel.
Video Input Alarm Input/Output RS485 Port RS232 Port
Network Port Video Out
Factory Reset Switch
Power Cord Connector
Your DVR can be used with either NTSC or PAL equipment.
NOTE: You cannot mix NTSC and PAL equipment. For example you cannot use a PAL camera and an NTSC
monitor.
Video Input
Alarm Input/Output
Connect the coaxial cables from the video sources to the BNC Video In connectors.
NOTE: To make connections on the Alarm Connector Strip, press and hold the button
and insert the wire in the hole below the button. After releasing the button, tug gently
on the wire to make certain it is connected. To disconnect a wire, press and hold the
button above the wire and pull out the wire.
User’s Manual
4
Alarm In 1 to 8: You can use external devices to signal the DVR to react to events. Mechanical or electrical switches
can be wired to the Alarm In and GND (Ground) connectors. The threshold voltage of electrical switches for NC
(Normally Closed) is above 2.4V and for NO (Normally Open) is below 0.3V, and should be stable at least 0.5 seconds
to be detected. The voltage range of alarm input is from 0V to 5V. See Chapter 3 ─ Configuration for configuring
alarm input.
GND (Ground): Connect the ground side of the Alarm input and/or alarm output to the GND connector.
NOTE: All the connectors marked GND are common.
NO (Normally Open): Connect the device to the COM and NO (Normally Open) connector. NO is a relay output
which sinks 1A@30VDC. See Chapter 3 ─ Configuration for configuring alarm output.
Connector Pin Outs:
Alarm In (1 to 8)
Alarm Inputs 1 to 8
GND
Chassis Ground
COM
Relay Common
NO
Relay Alarm Out (Normally Open)
RS485 Port
Connector Pin Outs:
Master Unit Slave Unit
+ → To → TX+/RX+
– → To → TX–/RX–
RS232 Port
Connector Pin Outs:
Master Unit Slave Unit
RX → To → TXD
TX → To → RXD
GND → To → GND
NOTE: Refer to the following for pin-out details for the 9-pin connector of the slave unit.
Male
Female
Pin 2
RXD (Receive Data)
Pin 3
TXD (Transmit Data)
Pin 5
GND (Ground)
Network Port
CAUTION: The network connector is not designed to be connected directly with cable or wire
intended for outdoor use.
The DVR can be controlled remotely by an external device or control system, such as a control keyboard,
using RS485 half-duplex serial communications signals. The RS485 connector can also be used to control
PTZ (pan, tilt, zoom) cameras. Connect RX+/TX+ and RX–/TX– of the control system to the + and –
(respectively) of the DVR. See Chapter 3 ─ Configuration and the PTZ camera or remote controller
manufacture’s manual for configuring the RS485 connection.
An RS232 port is provided to connect remote control devices such as a control keyboard. PTZ cameras or
text-in devices can also be connected to the RS232 port. See Chapter 3 ─ Configuration and the PTZ camera,
text-in device or remote controller manufacturer’s manual for configuring the RS232 connection.
The DVR can be networked using the 10Mb/100Mb/1Gb Ethernet connector. Connect a Cat5 cable
with an RJ-45 jack to the DVR connector. The DVR can be networked with a computer for remote
monitoring, searching, configuration and software upgrades. See Chapter 3 ─ Configuration for
configuring the Ethernet connections.
Digital Video Recorder
5
Video Out
A VGA connector is provided so that you can use a standard, multi-sync computer monitor
as your main monitor. Use the cable supplied with your monitor to connect it to the DVR.
An HDMI (High-Definition Multimedia Interface) connector is provided so that you can
use an HDMI monitor as your main monitor.
NOTE: Connect the monitor before the DVR boots so that video can be displayed on the monitor with the resolution
you have set during system setup. If you want to use both the HDMI and VGA Monitor connectors, one
of the monitors should be connected before the DVR boots, and the other monitor should be connected
after the DVR boots.
Factory Reset Switch
The DVR has a Factory Reset switch to the left of the HDMI connector on the rear panel. This
switch will only be used on the rare occasions that you want to return all the settings to the original
factory settings.
CAUTION: When using the Factory Reset, you will lose any settings you have saved.
To reset the unit, you will need a straightened paperclip:
1. Turn the DVR off.
2. Turn it on again.
3. While the DVR is initializing, the front panel LEDs will blink. When the front panel LEDs blink, poke the
straightened paperclip into the unlabeled hole to the left of the HDMI connector.
4. Hold the reset switch until the DVR’s internal buzzer sounds twice.
5. Release the reset switch. All of the DVR’s settings are now at the original settings it had when it left the factory.
Power Cord Connector
WARNING: ROUTE POWER CORDS SO THAT THEY ARE NOT A TRIPPING HAZARD. MAKE
CERTAIN THE POWER CORD WILL NOT BE PINCHED OR ABRADED BY FURNITURE.
DO NOT INSTALL POWER CORDS UNDER RUGS OR CARPET.
THE POWER CORD HAS A GROUNDING PIN. IF YOUR POWER OUTLET DOES NOT
HAVE A GROUNDING PIN RECEPTACLE, DO NOT MODIFY THE PLUG. DO NOT
OVERLOAD THE CIRCUIT BY PLUGGING TOO MANY DEVICES IN TO ONE CIRCUIT.
CAUTION: Ensure the DVR is not near any heat source that could cause overheating.
CAUTION: The DVR does not have an internal fan so leave a clearance of at least 6 inches near
ventilation hole areas on each side panel of the unit for proper ventilation.
Your DVR is now ready to operate. Refer to Chapter 3 ─ Configuration and Chapter 4 ─ Operation.
Connect the connector from the adaptor to the DVR, and connect the AC power cord to the adaptor and
then to the wall outlet.
User’s Manual
6
Digital Video Recorder
7
Chapter 3 — Configuration
NOTE: Your DVR should be completely installed before proceeding. Refer to Chapter 2 — Installation.
Front Panel Controls
Figure 3: 8-Channel DVR front panel.
Camera Buttons HDD LED Alarm Out LED Arrow Buttons
Play/Pause Button Menu Button PTZ/Zoom Button Panic Button
Search Button USB Connector
The front panel looks and operates much like a VCR combined with a multiplexer. Many of the buttons have multiple
functions. The buttons on the infrared remote control, while laid out differently, perform the same functions as those
on the front panel. The following describes each button and control. Take a few minutes to review the descriptions.
You will use these to initially set up your DVR and for daily operations.
NOTE: A separate Alarm button on the front panel is not provided. Pressing any button on the front panel resets
alarm output including the internal buzzer when the alarm is activated. However, when you are in the
menu or PTZ mode, you have to exit the menu or PTZ mode first to reset alarm output.
The infrared sensor on the DVR is just to the left of the HDD LED. Make certain that nothing blocks the
sensor, or the remote control will not function properly.
When you use wireless communication devices (such as Wi-Fi or Bluetooth) near the DVR, the remote
control might not function properly.
You can also use a USB mouse (not supplied) to navigate through the screens and menus much like
you would on a computer.
Camera Buttons
Pressing the individual camera buttons will cause the selected camera to display full screen, and pressing the button
again toggles between different display formats. The available formats are: PIP, 2x2, 1+5, 1+7 and 3x3. Buttons are
also used to enter passwords.
In the PTZ mode, pressing the button 1 zooms in the screen and the button 2 zooms out the screen, and pressing the
button 3 focuses near and button 4 focuses far.
HDD LED
The HDD LED flickers when the DVR is recording or searching video on the hard disk drive.
Alarm LED
The Alarm LED is lit when alarm output or internal buzzer is activated.
User’s Manual
8
Arrow Buttons
These buttons are used to navigate through menus and GUI. You can also use them to change numbers by highlighting
a number in the menu and using the Up and Down arrow buttons to increase or decrease the number’s value.
These buttons are also used to control Pan and Tilt when in the PTZ mode. When in the PIP display format, pressing
the Up and Down arrow buttons moves the position of the small screen counter-clockwise and clockwise, and pressing
the Left and Right buttons changes the PIP screen size.
In the playback mode, pressing the button plays video backward at high speed. Pressing the button again toggles
the playback speed from , and . The screen displays , and respectively. Pressing the
button plays video forward at high speed. Pressing the button again toggles the playback speed from , and
. The screen displays , and
respectively. When in the pause mode, pressing the
button moves
to the next image and pressing the
button moves to the previous image.
Play/Pause Button
In the live monitoring mode, pressing the
button freezes the current screen and the screen displays
icon. When
in the playback mode, pressing the
button plays back images at regular speed or pauses playing video.
Pressing the button selects a highlighted item or completes an entry that you have made during system setup.
When in one of the multi-view formats, pressing and holding the button for three seconds or longer enters the
cameo mode and allows you to change the screen layout. Refer to the following Live Monitoring – Active Cameo Mode
section for details.
Menu Button
In the Live Monitoring mode and Search mode, pressing the
MENU button displays the menu icons on the right edge
of the screen. Pressing the button again hides the menu icons. During menu setup, pressing the button closes the current
menu or setup dialog box.
When in the live mode, pressing and holding the MENU button for three seconds or longer displays live channels
sequentially.
PTZ/Zoom Button
In the live monitoring mode, pressing the PTZ/ZOOM button enters the zoom mode, and pressing the button again
exits the zoom mode. When in the zoom mode, a rectangle displays on the screen. A rectangle shows the area that
will be enlarged. You can move the rectangle around using the arrow buttons. Pressing the
(Play/Pause) button
enlarges the area in rectangle.
In the live monitoring mode, pressing and holding the PTZ/ZOOM button for three seconds or longer enters the PTZ
mode, and pressing and holding the button again for three seconds or longer exits the PTZ mode. When in the PTZ
mode, pressing the arrow buttons or MENU button allows you to control properly configured cameras.
Panic Button
Pressing the PANIC button starts panic recoding of all camera channels, and displays on the screen. Pressing the
button again will stop panic recording.
Digital Video Recorder
9
Search Button
Pressing the SEARCH button enters the search mode, and pressing the button again exits the search mode. When
entering the search mode, video is paused. Pressing the (Play/Pause) button plays back video at regular speed.
The screen displays
when the DVR is in the Pause mode and the screen displays when the DVR is playing back
video. The button is also used to load a Preset View in the PTZ mode.
In the Search mode, pressing and holding the SEARCH button for three seconds or longer allows you to copy video
clips.
When in one of the multi-view formats, pressing SEARCH button enters the Triplex mode. The DVR supports the
Triplex function: monitoring, recording and playing back at the same time.
USB Port
Two USB ports on the front panel are provided to connect external hard disk or flash drives for video clip copying or
system upgrades. Position external drives close enough to the DVR so that you can make the cable connections, usually
less than 6 feet. Use the USB cable provided with the hard disk drive to connect it to the DVR.
A USB mouse (not supplied) can be connected to one of the ports. You can use the mouse to navigate through the
screens and menus much like you would on a computer.
A PostScript™ USB printer (not supplied) can be connected to one of the ports. You can print selected images resulting
from a search. Refer to Chapter 4 — Operation, Searching Video.
A USB to Serial converter can be connected to the USB port. Multiple text-in devices can be used with a USB to Serial
converter.
Remote Control Buttons
ID Button
Camera Buttons
Sequence Button
Freeze Button
Arrow Buttons
Menu Button
Playback Buttons
Panic Button
Layout Button
Zoom Button
PTZ Button
Enter Button
Alarm Button
PTZ Control Buttons
Back Up Button
Calendar Button
Figure 4: Infrared remote control.
NOTE: For simplicity, the button descriptions in this manual refer to the front panel buttons.
User’s Manual
10
ID Button
If a DVR System ID is set to 0, the infrared remote control will control that DVR without any additional operations.
(Refer to the System – General setup screen in this chapter for further information on setting the System ID.) If the
system ID is 1 to 16, you must to press the ID button and then press the number button (1 to 16 (+10 & 6)) in order to
control that DVR. If the System ID of two or more DVRs is set to 0, those DVRs will react to the infrared remote
control at the same time.
Camera Buttons
Pressing the individual camera buttons will cause the selected camera to display full screen. Buttons are also used to
enter passwords.
Sequence Button
When in the Live Monitoring mode, pressing the SEQUENCE button displays live channels sequentially.
Freeze Button
Pressing the
FREEZE button freezes the current live screen.
Arrow Buttons
These buttons are used to navigate through menus and GUI. You can also use them to change numbers by highlighting
a number in the menu and using the Up and Down arrow buttons to increase or decrease the number’s value. These
buttons are also used to control Pan and Tilt when in the PTZ mode.
When in the PIP display format, pressing the Up and Down arrow buttons moves the position of the small screen
counter-clockwise and clockwise.
Pressing the Left and Right buttons moves through screen pages in the Live Monitoring mode and Search mode.
Menu Button
In the Live Monitoring mode and Search mode, pressing the
MENU button displays the menu icons on the right edge
of the screen. Pressing the button also hides the menu icons. During menu setup, pressing the button closes the current
menu or setup dialog box.
Playback Buttons
Rewind: Pressing the
button plays video backward at high speed. Pressing the button again toggles the playback
speed from
, and .
Play/Pause: Pressing the
button plays back video at regular speed. The screen displays
when the DVR is
in the Pause mode and the screen displays
when the DVR is playing back video.
Fast Forward: Pressing the
button plays video forward at high speed. Pressing the button again toggles the
playback speed from
, and .
Stop: Pressing the button stops playback and enters the Live Monitoring mode.
Backward: When in the pause mode, pressing the button moves to the previous image.
Forward: When in the pause mode, pressing the button moves to the next image.
In the Live Monitoring mode, pressing any playback button enters to the Search mode.
Panic Button
Pressing the
PANIC button starts panic recoding of all camera channels, and displays on the screen. Pressing the
button again will stop panic recording.
Digital Video Recorder
11
Layout Button
Pressing the LAYOUT button toggles between different display formats. The available formats are: 3x3, 1+7, 1+5,
2x2 and PIP.
Zoom Button
Pressing the ZOOM button zooms the current image on the screen. A PIP with a rectangle temporarily displays showing
what area of the screen has been enlarged. You can use the arrow buttons to move the rectangle to another area.
PTZ Button
Pressing the PTZ button enters the PTZ (Pan/Tilt/Zoom) mode which allows you to control properly configured cameras.
Enter Button
The
(Enter) button selects a highlighted item or completes an entry that you have made during system setup. This
button is also used to enter the Cameo mode in the Live Monitoring mode or Search mode.
Alarm Button
Pressing the
ALARM button resets the DVR’s outputs including the internal buzzer during an alarm.
PTZ Control Button
While in the PTZ mode, the
PRESET buttons are used to save Presets and load a Preset View, the ZOOM buttons are
used to Zoom In and Zoom Out, and the FOCUS buttons are used for Near Focus and Far Focus.
Backup Button
Pressing the
BACK UP button allows you to copy video clips.
Calendar Button
In the search mode, pressing the CALENDAR button displays the Calendar Search screen.
Turning on the Power
Connecting the power cord to the DVR turns on the unit. The unit takes approximately 50 seconds to initialize.
Initial Unit Setup
Before using your DVR for the first time, you will want to establish the initial settings. This includes items such as
time and date, display language, camera, remote control, record mode, network and password. Your DVR can be set
up using various screens and dialog boxes.
Throughout the screens you will see
. Highlighting the and pressing the button gives you the opportunity
to reset that screen to its default settings.
Highlighting This page or All pages and pressing the button resets the current
page or all pages of the screen to its or their default settings.
User’s Manual
12
After you are finished with any setup screen, you can highlight Save and press the
button to save the changes
and exit the screen. If you do not wish to save the changes, highlight Cancel and press the
button to exit the screen.
Press the
MENU button or move the mouse pointer on the right edge of the screen and then select (Login) in the Live
Monitoring menu to enter the setup screens. The Login screen appears.
Select a User and enter the password by pressing the appropriate
combination of Camera number buttons and then the
button.
There is no default password when logging in the admin user for the
first time. If you do not know the password, click the button for
guidance.
Figure 5: Login screen.
NOTE: To assure the secure management of the system, setting up a password is strongly recommended.
If you cannot use the front panel buttons, click the
button using the mouse to enter a password, and
the virtual keyboard displays. See instructions below for using the virtual keyboard.
To log the user out of the system, press the
MENU button or move the mouse pointer on the right edge
of the screen and then select (Logout) in the Live Monitoring menu. The Logout screen displays asking
you to confirm whether or not you want to log out the current user.
Figure 6: Logout screen.
Setup Screen
Figure 7: Setup screen.
System Record Event Camera
Device Network
Notification
Display
Press the
MENU button or move the mouse pointer on the right edge of the screen and then select (Setup) in the Live
Monitoring menu to enter the setup screen.
While setting up the DVR, there will be many opportunities to enter names and titles. When making these entries, a
Virtual Keyboard will appear.
Digital Video Recorder
13
Use the arrow keys to highlight the character you want in the name or title and press
the
button. That character appears in the title bar and the cursor moves to the next
position. Pressing
toggles between the upper and lower case keyboards,
backspaces, and
deletes entered characters. Pressing toggles between different
keyboard layouts. You can use up to 31 characters including spaces in your title.
Special characters can be created using ^ and a capital letter; e.g., ^J for NL (New
Line), ^M for CR (Carriage Return). Special characters are commonly used by text
input devices and will be useful when performing Text-In Searches.
System Setup
General
Figure 8: System – General setup screen.
Highlight the Site box and press the button. A virtual keyboard appears that you can use to enter a Site Name.
Once you have entered your title, highlight OK and press the
button.
Highlight the box beside System ID and press the button. Change the number by highlighting it and using the
Up and Down arrow buttons to increase and decrease the number from 0 to 99.
NOTE: The System ID number is used to identify the unit when it is connected with other DVRs through the RS485
port. You cannot use the same ID number for two or more DVRs that are in the same RS485 network.
It is possible to have multiple DVRs with System ID 0 that are in the same area as long as they are not
part of an RS485 network. If this is the case, all will be controlled at the same time when using the infrared
remote control.
Highlight the box beside Language and press
button. A drop-down menu displays the available languages.
Highlight the desired language and press the
button.
The box beside Version displays the software version of the DVR. To upgrade the software, connect a USB device
containing the upgrade package file to the DVR. Highlight Upgrade… and press the button. The Upgrade
screen appears. The screen displays the upgrade package file names that are available. The “.rui” indicates that the
file is for software upgrades.
User’s Manual
14
Select the desired file and press the
button. Highlighting the Install button and pressing the button will
install the selected software package. Highlighting the Cancel button and pressing the
button will close the
window without upgrading the software. If the upgrade package file is not installed on the DVR properly, you will
get an error message. The system restarts automatically after completing the upgrade.
CAUTION: The USB device must be FAT16 or FAT32 format.
You can import saved DVR settings or export the current DVR settings. To import saved DVR settings, connect the
USB device containing the setup file (.dat) to the DVR. Highlight Setup – Import… and press the
button. Select
the desired setup file and press the Import button to import the selected settings and change the DVR settings accordingly.
Highlight Include Network Setup and press the
button to toggle between On and Off. When set to Off, the
network settings will not be changed.
To export the current DVR settings, connect the USB device to the DVR. Highlight Setup – Export… and press the
button. Highlight the box beside File name and press the button. A virtual keyboard allows you to enter the
file name. Selecting Export will save the current settings in .dat file format on the USB device.
NOTE: Even after changing the DVR settings by importing saved settings, the time-related settings (Date/Time,
Time Zone and Daylight Saving Time) will NOT be changed.
CAUTION: The USB device must be FAT16 or FAT32 format.
Highlight Show System Log… and press the button to display the System Log.
The System Log screen lists system activities (up to 5,000 from the latest) that have occurred along with the time and
date. The icon will be displayed in the last column for system activities of the remote site. You can scroll through
the log pages by using the Up and Down arrows, or you can go directly to a log page by entering the log page number
in the box at the bottom left of the screen. Highlight Close and press the
button to exit the screen.
Digital Video Recorder
15
To export the system log information, connect the USB device to the DVR. Highlight Export… and press the
button.
Highlight the box beside File name and press the
button. A virtual keyboard allows you to enter the file name.
Selecting Export will save the log information in .txt file format on the USB device.
NOTE: When opening the saved .txt file, setting to the proper character encoding and using fixed width fonts
will be required to read the file properly.
The box beside Recorded Data – From / To displays the time information of recorded data.
Highlighting Clear All Data… and pressing the button will clear all video data. You will be asked to verify that
you wish to clear all data before the DVR erases the video data. Clear All Data… will not clear the System Log.
Highlight Wizard and press the button. The Wizard setup screen appears. The Wizard setup guides you through
configuring the system for basic operation.
Select either Quick wizard or Network wizard and select the Next button to start the selected setup wizard.
NOTE: Selecting the Cancel button throughout the screens exits the Quick Setup Wizard without saving your
changes and returns to the main setup screen.
If you selected the Quick wizard, selecting the Next button starts the Quick Setup Wizard.
User’s Manual
16
Date/Time Setup
Date: Set the system date and select the date format.
Time: Set the system time and select the time format.
Time Zone: Select your time zone. The Time Zone can be selected on the map.
Use Daylight Saving Time: Selecting the box sets the system to use daylight saving time.
NOTE: The Date/Time will be set, and the clock will start when you click the Next button.
Record Method Setup
Select the desired recording mode from:
– Motion Event Record (Recommended)
– Continuous & Motion Event Record
– Continuous Record
NOTE: You should understand each recording mode before setting the DVR’s recording method.
Digital Video Recorder
17
Record Video Quality Setup
Select the desired video quality profile from:
– Higher Video Quality Priority Profile
– Standard Recording Profile
– Longer Recording Time Priority Profile
NOTE: The higher quality setting requires more storage space.
The recording resolution will be set to Very High when selecting High Video Quality Priority Profile, High
when selecting Standard Recording Profile, and Standard when selecting Longer Recording Time Priority
Profile.
The recording quality and recording speed of each camera channel will be set as show below according
to the Record Method and Record Video Quality you set.
HVQPP* SRP* LRTPP*
Motion Event Record Very High / 30 ips High / 5 ips Standard / 3 ips
Continuous & Motion
Event Record
Very High / 30 ips (Time)
Very High / 30 ips (Event)
High / 5 ips (Time)
Very High / 30 ips (Event)
Standard / 3 ips (Time)
High / 5 ips (Event)
Continuous Record Very High / 30 ips High / 5 ips Standard / 3 ips
* Record Video Quality: HVQPP (High Video Quality Priority Profile), SRP (Standard Recording Profile), LRTPP (Longer Recording Time
Priority Profile)
Select the Finish button to finish the Quick Setup Wizard and select the Go to Network Setup button to start the Network
Setup.
User’s Manual
18
If you selected the Go to Network Setup, select the Next button to start the Network Setup Wizard.
Internet Connection
Select whether or not your DVR is connected to the Internet.
Digital Video Recorder
19
LAN Setup
Select between Auto Configuration and Manual Configuration for network configuration, and then select the Test
button to test the network configuration you selected.
NOTE: Selecting Auto Configuration allows the DVR to automatically obtain LAN parameters (IP address, Gateway,
Subnet Mask and DNS Server address). Selecting Manual Configuration allows you to set up LAN
parameters manually.
The network configuration you set should be tested by selecting Test, otherwise the Next button will
cannot be selected, and you cannot move to the next step.
Use DSL/PPPoE Setup: Selecting the box allows you to set up the DSL network. Entering the ID and password
for DSL connection is required.
FEN Setup
FEN Name: Enter the DVR name to be registered on the DVRNS (DVR Name Service) server.
NOTE: The FEN Name you entered should be checked by selecting Test, otherwise the FEN changes will not
be saved.
When entering no name or a name already registered on the DVNRS server, an error message displays.
Select the Finish button to finish the Setup Wizard.
Loading...