Enelion Vertica Installation Manual
Enelion
Vertica
22 kW
Installation
manual
for the specialists
ver. 1.6
© Eneli on 05.2017
Enelion VERTICA
General notes
At various points in this manual you will see notes and precautionary warnings
regarding possible hazards. The symbols used have the following meanings:
WARNING!
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION!
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
ATTENTION!
Indicates a situation which, if not avoided could result
in property damage.
ESD
This symbol reminds you of the possible consequences of
touching electrostatically sensitive components.
Notice
Notes on use of equipment and useful practical tips are identied
by “i”. Notices do not contain any information that draws
attention to potentially dangerous or harmful functions.
Additional important information.
Technical Specications
Two charging panels: socket / cable (depends on version),
3x400V AC ~ 50Hz,
22kW (32A) for one charging panel,
3P+N+PE,
Standby power - 4W for one charging panel.
Instal lation manua l ver. 1.6, © Enelio n 05.2017 1
Important information
1 Important information
1.1 Safety instructions
WARNING!
Not observing the safety
instructions can result in risk
of death, injuries and damage
to the device! ENELION LTD assumes no
liability for claims resulting from this!
Electrical hazard!
The installation, commissioning and
maintenance of the charging station may only
be performed by correctly trained, qualied
and authorized electricians who are fully
responsible for the compliance with existing
standards and installation regulations.
Only supply the terminals from 3 phases 400V with
grounded sources!
Before commissioning, check all screw and terminal
connections for rm seating!
The connector panel cover may never be left open
unattended. Mount the connector panel cover if you
leave the charging station.
Do not remove any notices on the device, such as
safety symbols, warning notices, rating plates,
nameplates or cable markings!
Obser ve the instructions given for selecting the
location and the constructional requirements!
If the specications for the location are not
obser ved, this can result in death, serious physical
injury or equipment damage if the corresponding
precautionary measures are not met!
Pull the charging cable only at the plug and not at
the cable out of the connector.
Ensure that the charging cable is not mechanically
damaged (bent, pinched or run over) and the
connection area does not come into contact with
heat sources, dirt or water.
5 safety rules:
- Shut down all poles and all sides!
- Secure against reactivation!
- Check that the equipment is voltage-free!
- Ground and short-circuit!
- Cover adjacent live par ts and restrict
access to hazardous areas!
Use of the charging station with open cable insertion
openings is prohibited.
Do not carry out any unauthorized conversion work
or modications to the charging station!
Repair work to the charging station is not permitted
and may only be performed by the manufacturer
(replacement of the charging station)!
2
Instal lation manua l ver. 1.6, © Enelio n 05.2017
Enelion VERTICA
Important information
ATTENTION!
Risk of damage!
Make sure that the charging station is not damaged
by improper handling (anchoring, housing cover,
socket, inner parts etc.).
Do not open the lid of terminal in the rain!
Risk of damage the aluminium and plexi housing!
- Use only detergents dedicated for anodised
aluminium / plexi,
- Do not tighten the mounting screws with force.
Electrostatically sensitive
components
Information for technicians who are permitted to
open the device:
Risk of damage!
Electronic components can be destroyed if touched!
Before handling components, make sure you
perform an electrical discharge by touching
a metallic, grounded object!
1.2 Intended use
NOTICE
Enelion Vertica is a charging terminal for outdoor
area at which electrically operated vehicles can be
charged.
Two vehicles can be charged at the same time, with 3
phases, 32A and maximum 22kW power.
The charging station is designed for installation on
a pavement mounted column.
The respective national regulations must be
obser ved with regard to the installation and
connection of the charging terminal.
The intended use of the device always includes the
compliance with the environmental conditions for
which this device was developed.
The device was developed, manufactured, inspected
and documented in compliance with the relevant
safety standards. Therefore, the products do not
pose any danger to the health of persons or a risk
of damage to other property or equipment under
normal circumstances, provided that the instructions
and safety precautions relating to the intended use
are properly observed.
The instructions contained in this manual must be
followed precisely in all circumstances.
Failure to do so could result in the creation of
potential sources of danger or the disabling of safety
devices. Apart from the safety instructions given
in this manual, the safety precautions and accident
prevention measures appropriate to the situation in
question must also be observed.
Only electrical vehicles or their chargers may be
connected. A connection of other loads (e.g. electric
tools) is not permitted!
Instal lation manua l ver. 1.6, © Enelio n 05.2017
3
Loading...