Enduro SM1000-2P, SM1000-2PF User Manual
TM
TM
SM1000
Model
SM1000-2P
Voltage:
220
Phase:
1
Cycles:
50/60
Variable Speed
to 3800 RPM
TM
SM1000
Model
SM1000-2PF
Voltage:
220
Phase:
1
Cycles:
50/60
Variable Speed
to 3800 RPM
nduro
E
ELITE
SM1000-2P & SM1000-2PF
SERVO MOTOR WITH POSITIONER USER INSTRUCTIONS & PARTS LISTING
INSTRUCTION ET LISTE DES PIÈCES DE L’UTILISATEUR DU MOTEUR SERVO
DE POSITIONNEUR
SERVO MOTOR WITH POSITIONER USER INSTRUCTIONS & PARTS LISTING
SM1000-2P ENDURO™ ELITE SM1000-2PF ENDURO™ ELITE
INSTRUCTIONS DU FRANCAIS - PAGE 10 >
LISTE DES PIECES DU FRANCAIS - PAGE 17 >
Copyright © 2011 Enduro™ Servo Motor
Tous Droits Réservé © 2011 Moteur Servo Enduro™
Derecho de autor© 2011 Enduro™ Servo Motor
www.endurosaves.com
INSTRUCCIÓN EN ESPAÑOL - PÁGINA 18 >
LISTA DE PARTES EN ESPAÑOL - PÁGINA 25 >
ENGLISH INSTRUCTIONS - PAGE 2 >
ENGLISH PARTS LISTING - PAGE 9 >
2 - ENGLISH
SM1000-2P & SM1000-2PF ENDURO™ ELITE SERVO MOTOR
WITH POSITIONER USER INSTRUCTIONS
Congratulations!
You have purchased the Enduro™ Elite SM1000 motor that pays for itself with 60% to 80% energy
savings compared to clutch motors. With the high and rising cost of electricity, you just can’t afford to
run a clutch motor any longer. The power and dependability of the brushless Enduro
exceptional. This workhorse just won’t quit.
Please read these instructions carefully before installation, operation or maintenance.
General Introduction
The Enduro™ Elite SM1000 Servo Motor is designed to meet almost all basic heavy duty and
continuous use requirements of various industrial sewing machines. It utilizes extremely powerful
rare-earth Neodymium permanent magnets. The motor produces almost no noise, saves energy and
is brushless, speed adjustable and durable. It provides a high starting torque even at low speed or
from a complete stop.
™
Elite SM1000 is
By using a modern technologically advanced microprocessor, Hall sensor and Pulse-Width Modulation
technology, the Enduro™ Elite SM1000 can be set to rotate at different maximum speeds, in either normal
or reverse directions, and can start with different accelerating speeds. It will stop automatically with any
interruption such as in-line voltage, electrical surge, radio frequency interference or overloading. It is
fully protected by the software and will give error messages indicating which problem is encountered. It
even works well in environments with an unstable electrical power supply.
The positioner motor comes with a positioner sensor kit included. With correct installation and settings,
Enduro™ Elite SM1000-2P can provide accurate Needle Positioning of either the UP or DOWN position
every time. In addition to Needle Positioning, Enduro
sends a 24VDC signal for activating a solenoid for lifting the presser foot on the sewing machine.
CAUTION
1. Remove your foot from the pedal when turning the power ON.
2. Turn the power switch OFF before replacing or threading the needle.
3. Turn the power OFF when leaving the machine.
4. When performing maintenance on the sewing machine, turn the motor power switch to
the OFF position. Remove the power cord from the back of the motor to completely
disable all power to the sewing machine.
5. Always ground the grounding wire.
6. Always turn off the power switch before connecting or disconnecting each connector.
7. To avoid an accident, do not alter this motor and control box.
™
Elite SM1000-2PF provides Foot Lift output which
Warranty
This product is covered with a 1 year limited warranty. If the motor fails to perform its designed function
due to manufacturer’s defects, contact the place you purchased it from for repair or replacement.
This warranty does not cover defects due to dropping, power surge, spikes or misuse.
www.endurosaves.com
ENGLISH - 3
Installation
Put the mounting bracket of the motor upwards to the bottom of the tabletop and x the motor to the
tabletop with the bolts provided. Connect the treadle rod with the connecting rod joint. Install the female
plug of the cable from the switch box into the power inlet socket in the back of the motor box.
Wiring
For 220 volt single phase motor follow the diagram below:
Note: When wiring the motor to the power source, connect both the black and white wires to
achieve 220 Volts (green to ground). If you are in an area (China / Europe) that supplies 220 Volts
from a single lead, then connect the power source to the black wire. The white wire will then be the
neutral and the green wire will be the ground.
Error Message and Trouble Shooting
E2: Motor Phase signal error.
E3: Motor protected against over-current.
E4: Circuit board error.
E5: Display module and control module communication error.
E6: Pedal position sensor error.
E8. Can not nd position DOWN.
E9. Can not nd position UP.
Setting Up
Turn on the switch located on the switchbox. The display will
show "POS.d" which means "needle position down", this means
the motor is now in "ready" status, ready to work or be set.
default "ready" status
www.endurosaves.com
Loading...