Endon YG-4002-SS, YG-4003-SS Instruction Manual

The Light pack contains:

The following tools may be required:

YG- 4002-SS / YG- 4003-SS - Outdoor fittings.

Safety Warnings

INSTRUCTION MANUAL

These products are only suitable for connection to a 240V~50Hz supply.
It is recommended that these floor standing lights are installed by a qualified electrician in accordance with
current IEE Wiring Regulations and local Building Regulations and are for the Domestic environment only.
These light fittings should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature
circuit breaker).
These lights have an IP44 (splash proof) rating suitable for use outdoors.
Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm
(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it
must come out of the mounting surface in line with the entry to the fitting and should be at least 250mm in
length.
Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,
a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a
protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable
covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,
conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable
disturbance of the ground.
These product contain breakable parts – be careful during handling and maintenance to avoid breakage.
These fittings use none-replaceable LED`s.
We recommend that you do not stare directly into the light beam (of the LED`s).
If any part of the (LED) housing is broken or cracked then it cannot be replaced and the fittings must not be
used - as the water ingress protection has been compromised.
IMPORTANT: To achieve maximum corrosion resistance the surface of the Stainless Steel must be kept clean.
Surface contamination and the formation of deposits are critical factors which may lead to drastically reduced
life. An example is salt deposits from marine conditions. Careful washing with soap or a mild detergent and
warm water followed by a clean water rinse and finally wiping dry is usually adequate for most S/S items used
in the domestic environment. Care must be taken to turn off the mains supply until the cleaning process has
been completed and the fitting is completely dry.

If any modification is made it will invalidate the warranty and may render the products unsafe.

Before you start

Please read these instructions carefully before fitting your new light and retain for reference.
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker
before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.
Ensure that there are no cables / pipes beneath the surface (other than the supply cable for this fitting).

The mounting surface must be secure and able to accommodate the weight / height of the fitting. If installing on an
existing secure (concrete) base, use the holes in the lamp post base as a template to drill suitable fixing holes and
prepare with suitable ground fixing bolts (not supplied).The supply cable (at least 250mm) must come out of the
mounting surface and directly into the terminal block in the base / post of the fitting.
Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.

DO NOT CONNECT THIS PRODUCT TO A DIMMER SWITCH.

IP44 rated LED Floor standing light.

Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.

2

Assembly / user instructions

N210 109

Diagram A

Diagram B

1. Diagram A. Determine the

Cable clamp

WIRING DETAILS

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.

Endon Lighting
LS9 0SE

20150706

position of your light fitting.
Ensure there is sufficient
power cable to connect to
the fitting – we recommend
at least 250mm. Ensure
that the mounting surface
is solid. If you are using
anchor bolts (not supplied)
prepare the mounting
surface as appropriate (and
ensure that there are no
other cables or pipes
beneath the surface).

2. Place the base over the
cable and use it as a
template to mark the
mounting hole positions.
Drill and plug the holes
ready to mount the fitting
later.

3. Diagram B. Pull the
terminal block assembly
out of the base of the
fitting. Remove the cable
clamp and take the lid off
the terminal block housing
to expose the internal
terminal block.

Connect the house wiring to

4.

the internal terminal block.

NOTE: This is a Class I
fitting and must be
earthed. Connect the

incoming mains as per the

WIRING DETAILS diagram

5. Re-fit the terminal block into

its housing and secure –
ensuring that all seals are
correctly located.

6. Secure the cable clamp
over the incoming cable
and then push the terminal
block assembly as far into
the base / stem as
possible.

7. Secure the post (screws /
bolts etc not supplied) to
the mounting surface
making sure that all
cables are contained
inside the fitting.

8. Turn on the power and

test.