Endon EL-40113 Instruction Manual

The Light pack contains:

PIR Wall light with non-replaceable led`s.

PIR Specifications (all values are approximate).

Working Temperature: -20°C / +50°C.
Voltage: 180VAC – 250VAC 50-60Hz.
Load: Max 60w Incandescent.
Detection distance: 0 – 12m.
Detection angle: 130°.
Time on: 10 seconds.

Lux level: < 30lux / >70lux

The following tools may be required:

Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.

INSTRUCTION MANUAL

This product is only suitable for connection to a 240V~50Hz supply.
It is recommended that this light is installed by a qualified electrician in accordance with current IEE Wiring

Regulations and local Building Regulations.
The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature
circuit breaker).

This light has an IP44 (splash proof) rating suitable for use outdoors.
Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm

2

(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it
must come out of the flat surface of the mounting surface in line with the entry to the fitting.

Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,
a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a
protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable
covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,
conduits and ducts shall be at a suffici ent depth to avoid being damaged by any reasonably foreseeable
disturbance of the ground.

This product contains breakable parts – be careful during handling and maintenanc e to avoid breakage.
This fitting uses none-replaceable LED`s. We recommend that you do not stare directly into the light beam.
The diffuser (cover) can become hot in use. Switch off and allow 10 minutes to cool before cleaning (using a

dry cloth only – do not use liquid or abrasive c leaners).
If the cover is broken or cracked then it cannot be replaced and the fittings must not be used - as the water

ingress protection has been compromised.
Clean using a dry cloth only – do not use liquid or abrasive cleaners.
If any modification is made it will invalidate the warranty and may render the product unsafe.

Before you start

Please read these instructions carefully before fitting your new light and retain for reference.
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker
before commencing installation.
Ensure that no one else has access that would enab le the supply to be inadvertently reconnected.

Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly
Make sure all screws / nuts, including electrical connections etc are fully tightened before use.

EL- 40113 - LED PIR Outdoor wall fitting.

Safety Warnings

Endon Lighting Ltd

Leeds
UK

LS9 0SE

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.

Assembly / user instructions

L240 002

Diagram A

Diagram B

Diagram C

1. Diagram A. Use a thin bladed screw driver to gently

prise off the front cover.

2. Diagram B. Determine the position of your light
fitting taking into account the exit position of the
cable. Ensure that the mounting surface is solid,
preferably a brick or block wall and ensure that there
are no other cables or pipes beneath the surface.
Use the back plate as a template and mark the 2
fixings holes. Ensure there is sufficient cable coming
out of the wall to connect to the terminal block.

3. Remove the terminal block cover plate.

4. Diagram C. Bring the house wiring to the inter n al

terminal block. The cable entry grommet must be
securely in place to ensure that the water ingress
protection is maintained. Use appropriate fixings to
secure the back plate to the wall, making sure the
back plate is correctly aligned and you do not trap or
damage any cables. Fix the back plate to the wall.
Connect the house wiring – see wiring details.
NOTE: This is a Class II fitting and must not be

earthed. If you have any earth cables make sure
that they are connected to each other – to
maintain earth continuity throughout your
property – and wrap the earth terminal an d
connections in 2 layers of good quality insulation
tape and keep them away from the terminal
connections of the fitting.

5. Re-fit the terminal block cover plate.

6. Re-fit the front cover.

7. Turn on the power and test.

Front cover.

Mounting

screw holes

Terminal block
cover plate.

Mains supply
cable