Endon EL-10135, EL-10134 Instruction Manual

1

The Light pack contains:

Light fitting with LED Power Supply and
mounting bracket.

The following tools may be required:

Selection of cross and flat head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.

INSTRUCTION MANUAL

These products are only suitable for connection to a 240V~50Hz supply in accordance with current
IEE wiring Regulations and should be installed in accordance with local Building Regulations and
are for Domestic use only and not suitable for bathroom use.

The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp
miniature circuit breaker).

If in doubt we recommend you contact a qualified electrician. Before installing your light fitting
always:
Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit
breaker before commencing installation.
Ensure that no one else has access that would enable the supply to be inadvertently reconnected.

This product contains delicate parts – be careful during handling and maintenance to avoid
breakage.

The fitting may become hot during use so please switch off and allow 10 minutes to cool before
maintenance or cleaning the fitting.

Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
This is a fixed, not a portable, light fitting and as such it must be secured to the mounting surface

and hard wired.
This fitting uses none-replaceable LED`s. We recommend that you do not stare directly into the light
beam.

Make sure that all exposed cables – mains in and connection cables – are routed such they will not
be damaged and the safety of the product compromised.

All basic insulation must be contained within the connection housing.
If any modification is made it will invalidate the warranty and may render the product unsafe.

Before you start

Please read these instructions carefully before fitting your new light and retain for reference.
Make sure that there are no pipes or cables beneath the mounting surface.

Check the packaging and make sure that you have all the required parts.
Follow each assembly step in order to prevent incorrect assembly.

This is a class II, double insulated light, (denoted by the symbol

) and the fitting does not require an
Earth.
Any earth cables present must be connected together, to ensure earth continuity of the circuit, and isolated
from the Live and Neutral terminal connections, if necessary by wrapping the earth terminal and connections
with 2 layers of good quality insulation tape.

Make sure all screws / nuts, including electrical connections etc are fully tightened before use.
This type of Light Fitting must not be connected to a Dimmer.

EL-10134 and EL-10135 - Fixed LED lights.

Safety Warnings

2

Assembly/ User Instructions

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.

Endon lighting Ltd.

Leeds.
UK
LS9 0SE

P040 101

Diagram A

1. Decide on the position of

your light fittings. Ensure
there is a solid mounting
surface and ensure that
there are no cables or
pipes beneath the
surface. If the surface is
timber frame and
plasterboard then please
use appropriate fixings.
Ensure the fixings used
can support the weight of
the light. Determine the

position of the mains
supply in relation to the
lights and the proposed
cable runs.

2. Diagram A. Secure the
fixing brackets to the
mounting surface as
shown.
Start by drilling a small
pilot hole then screw the
brackets to the surface.

3. Diagram B. Secure the
lights in place.

4. Diagram C. Connect the
light to the LED power
supply and then secure
the LED power supply to
a suitable surface as
shown.

5. Connect the trailing
cable to the house wiring.

NOTE: This is a Class
II, double insulated
fitting and does not
require an earth
connection – see
comments in `Before
You start`. The mains in
Live supply should be
connected to the L
terminal and the mains
in Neutral supply to the
N terminal. – see wiring
details. IMPORTANT:-

All basic insulation
MUST be inside the
connection box housing.

6. Turn on the power and
test.

Diagram B

Diagram C

LED Power

supply