Encore electronic ENUWI-NX2 User Manual

ENUWI-NX2

IEEE 802.11n draft 2.0 Wireless

USB 2.0 Adapter

Users Guide

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.

IMPORTANT NOTE:
Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the
specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance
requirements, please follow operation instruction as documented in this manual.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

SAR compliance has been established in typical laptop computer(s) with Cardbus slot, and product could be used in typical laptop
computer with Cardbus slot. Other application like handheld PC or similar device has not been verified and may not compliance with
related RF exposure rule and such use shall be prohibited.

Europe – EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been
applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

EN 60 950-1: 2001 +A11: 2004

Safety of Information Technology Equipment

EN 50392: (2004-01)

Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human
exposure to electromagnetic fields (0 Hz - 300 GHz)

EN 300 328 V1.7.1: (2006-10)

Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment
operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential
requirements under article 3.2 of the R&TTE Directive

EN 301 489-1 V1.6.1: (2005-09)

i

Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 1: Common technical requirements

EN 301 489-17 V1.2.1 (2002-08)

Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio
equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN
equipment

This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries,
except in France and Italy where restrictive use applies.

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device
for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.

This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10
mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum
authority in France.

0560

[Czech]

[Danish]

[German]

[Estonian]

[Spanish]

[Greek]

[French]

Deutsch

English

Español

Ελληνική

Français

Česky

Dansk

Eesti

Encore Electronics Inc tímto prohlašuje, že tento ENUWI-NX2 je ve shodě se základními požadavky a
dalšími příslušnými ustanoveními směrnice 1999/5/ES.

Undertegnede Encore Electronics Inc erklærer herved, at følgende udstyr ENUWI-NX2 overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Hiermit erklärt [Name des Herstellers], dass sich das Gerät ENUWI-NX2 in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.

Käesolevaga kinnitab Encore Electronics Inc seadme ENUWI-NX2 vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Hereby, Encore Electronics Inc., declares that this ENUWI-NX2 is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.

Por medio de la presente Encore Electronics Inc declara que el ENUWI-NX2 cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Encore Electronics Inc ΔΗΛΩΝΕΙ ΟΤΙ ENUWI-NX2 ΣΥΜΜΟΡΦΩΝΕΤΑΙ
ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

1999/5/ΕΚ.
Par la présente Encore Electronics Inc déclare que l'appareil ENUWI-NX2 est conforme aux exigences

essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

Italiano

[Italian]

Latviski

[Latvian]

Lietuvių

[Lithuanian]

Nederlands

Con la presente Encore Electronics Inc dichiara che questo ENUWI-NX2 è conforme ai requisiti
essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.

Ar šo Encore Electronics Inc deklarē, ka ENUWI-NX2 atbilst Direktīvas 1999/5/EK būtiskajām prasībām
un citiem ar to saistītajiem noteikumiem.

Šiuo Encore Electronics Inc deklaruoja, kad šis ENUWI-NX2 atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.

Hierbij verklaart Encore Electronics Inc dat het toestel ENUWI-NX2 in overeenstemming is met de

ii

[Dutch] essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Malti

[Maltese]

Magyar

[Hungarian]

Polski

[Polish]

Português

[Portuguese]

Slovensko

[Slovenian]

Slovensky

[Slovak]

Suomi

[Finnish]

Svenska

[Swedish]

Česky

[Czech]

Hawnhekk, Encore Electronics Inc, jiddikjara li dan ENUWI-NX2 jikkonforma mal-ħtiġijiet essenzjali u
ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

Alulírott, Encore Electronics Inc nyilatkozom, hogy a ENUWI-NX2 megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Niniejszym Encore Electronics Inc oświadcza, że ENUWI-NX2 jest zgodny z zasadniczymi wymogami
oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Encore Electronics Inc declara que este ENUWI-NX2 está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.

Encore Electronics Inc izjavlja, da je ta ENUWI-NX2 v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.

Encore Electronics Inc týmto vyhlasuje, že ENUWI-NX2 spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.

Encore Electronics Inc vakuuttaa täten että ENUWI-NX2 tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Härmed intygar Encore Electronics Inc att denna ENUWI-NX2 står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

Encore Electronics Inc tímto prohlašuje, že tento ENPWI-NX2 je ve shodě se základními požadavky a
dalšími příslušnými ustanoveními směrnice 1999/5/ES.

[Danish]

Deutsch

[German]

[Estonian]

English

Español

[Spanish]

Ελληνική

[Greek]

Français

[French]

Italiano

[Italian]

Latviski

[Latvian]

Dansk

Eesti

Undertegnede Encore Electronics Inc erklærer herved, at følgende udstyr ENUWI-NX2 overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.

Hiermit erklärt [Name des Herstellers], dass sich das Gerät ENPWI-NX2 in Übereinstimmung mit den
grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG
befindet.

Käesolevaga kinnitab Encore Electronics Inc seadme EPWI-NX2 vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.

Hereby, Encore Electronics Inc., declares that this ENPWI-NX2 is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.

Por medio de la presente Encore Electronics Inc declara que el ENPWI-NX2 cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Encore Electronics Inc ΔΗΛΩΝΕΙ ΟΤΙ ENPWI-NX2 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ
ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ

1999/5/ΕΚ.
Par la présente Encore Electronics Inc déclare que l'appareil ENPWI-NX2 est conforme aux exigences

essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Con la presente Encore Electronics Inc dichiara che questo ENPWI-NX2 è conforme ai requisiti

essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo Encore Electronics Inc deklarē, ka ENPWI-NX2 atbilst Direktīvas 1999/5/EK būtiskajām prasībām

un citiem ar to saistītajiem noteikumiem.

Lietuvių

[Lithuanian]

Nederlands

[Dutch]

Malti

[Maltese]

Šiuo Encore Electronics Inc deklaruoja, kad šis ENPWI-NX2 atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.

Hierbij verklaart Encore Electronics Inc dat het toestel ENPWI-NX2 in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.

Hawnhekk, Encore Electronics Inc, jiddikjara li dan ENPWI-NX2 jikkonforma mal-ħtiġijiet essenzjali u
ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.

iii

Magyar

[Hungarian]

Alulírott, Encore Electronics Inc nyilatkozom, hogy a ENPWI-NX2 megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.

Polski

[Polish]

Português

[Portuguese]

Slovensko

[Slovenian]

Slovensky

[Slovak]

Suomi

[Finnish]

Svenska

[Swedish]

Niniejszym Encore Electronics Inc oświadcza, że ENPWI-NX2 jest zgodny z zasadniczymi wymogami
oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.

Encore Electronics Inc declara que este ENPWI-NX2 está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.

Encore Electronics Inc izjavlja, da je ta ENPWI-NX2 v skladu z bistvenimi zahtevami in ostalimi
relevantnimi določili direktive 1999/5/ES.

Encore Electronics Inc týmto vyhlasuje, že ENPWI-NX2 spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.

Encore Electronics Inc vakuuttaa täten että ENPWI-NX2 tyyppinen laite on direktiivin 1999/5/EY
oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.

Härmed intygar Encore Electronics Inc att denna ENPWI-NX2 står I överensstämmelse med de
väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.

iv

TABLE OF CONTENT

Introduction ................................................................................................ 1

Overview of this User’s Guide ............................................................................... 1

Unpacking and Setup.................................................................................. 2

Unpacking .............................................................................................................. 2

Setup....................................................................................................................... 2

IDentifying external components ............................................................... 3

LED ........................................................................................................................ 3

Check the installation ............................................................................................. 3

Software Installation................................................................................... 4

Windows Based Utility Installation........................................................................ 4

Wireless Utility Setting .............................................................................. 6

Link Information .................................................................................................... 6

Configuration.......................................................................................................... 7

Site Survey ........................................................................................................... 10

Profile ................................................................................................................... 11

WPS...................................................................................................................... 12

About.................................................................................................................... 17

Technical Specifications........................................................................... 18

v

INTRODUCTION

Congratulations on your purchase of ENUWI-NX2 Wireless 802.11n USB Adapter.
This manual contains detailed instructions regarding the operation of this product.

Please keep this manual for future reference.
With the ENUWI-NX2 Wireless 802.11n USB Adapter, a desktop or laptop

computer can communicate with another computer wirelessly. An easy-to-use
utility is bundled with the ENUWI-NX2 Wireless 802.11n USB Adapter for
configuration, monitoring, and diagnostic purposes.

The ENUWI-NX2 Wireless 802.11n USB Adapter can wirelessly transmit and
receive data, at a speed of up to 300 Mbps.

The ENUWI-NX2 Wireless 802.11n USB Adapter provides users with access to
real-time information anywhere in their organization. The mobility of the ENUWI­NX2 Wireless 802.11n USB Adapter provides productivity and service, which are
not available under wired networks. The ENUWI-NX2 Wireless 802.11n USB
Adapter can easily adapt from peer-to-peer networks, suitable for a small number of
users, to full infrastructure networks of thousands of users that allow roaming
around a broad area.

Overview of this User’s Guide

Introduction. Describes the ENUWI-NX2 Wireless 802.11n USB Adapter and its

features.

Unpacking and Setup. Helps you get started with the basic installation of the

ENUWI-NX2 Wireless 802.11n USB Adapter.

Hardware Installation. Describes the LED indicator on the Adapter.
Software Installation. Describes how to setup the driver and the utility setting.
Technical Specifications. Lists the technical (general, physical and environmental)

specifications of the ENUWI-NX2 Wireless 802.11n USB Adapter.

1

UNPACKING AND SETUP

This section provides unpacking and setup information for the ENUWI-NX2
Wireless 802.11n USB Adapter.

Unpacking

The box should contain the following items:

 One ENUWI-NX2 Wireless 802.11n USB Draft 2.0 USB Adapter
 One Driver & Utility CD-ROM

If any item is found missing or damaged, please contact your local reseller or the
store of purchase for replacement.

Setup

Before installation, check the following:

 Make sure your computer is running at least a 300MHz or above processor with

256MB RAM or above

 Make sure the USB port where the ENUWI-NX2 Wireless 802.11n USB

Adapter is to be used is a USB 2.0 port

 The operating system on your computer must be any of the following:

Windows® 2000 (Service Pack 4), XP (Service Pack 2), Windows Vista™

 A draft 802.11n or 802.11b/g access point.
 Make sure the environment has minimal radio signal interference and/or

obstructions.

2

IDENTIFYING EXTERNAL COMPONENTS

LED

When the LED is blinking, the WLAN Adapter is transmitting or receiving data on
the Wireless Ethernet network.

Check the installation

The LED of the ENUWI-NX2 Wireless 802.11n USB Adapter is clearly visible and
the status of the network link can be seen instantly:

1. When connected to the USB port and the driver were installed, the LINK LED

will start blinking, and it means that the device is starting to scan a wireless
device near the ENUWI-NX2 Wireless 802.11n USB Adapter.

2. While the ENUWI-NX2 Wireless 802.11n USB Adapter linked up to the Access

Point or to other Wireless LAN station, the LINK LED will always light up.

3

SOFTWARE INSTALLATION

This section describes how to install the driver and utility for the ENUWI-NX2
Wireless 802.11n.

Windows Based Utility Installation

1) Insert the Utility and Driver CD-ROM into your computer’s CD-ROM Drive and

then click the Setup Wizard.

2) Follow the Install Shield Wizard Instructions

4

3) Click Finish to restart the computer.

4) Plug the ENUWI-NX2 Wireless 802.11n into an available USB slot on your

computer.

5

WIRELESS UTILITY SETTING

The user can configure the wireless settings using the Wireless Adapter
Configuration Utility. Double-click the utility icon that appears in the taskbar.

The Wireless Adapter Configuration Utility is divided into six sections: Link Info,
Configuration, Site Survey, Profile, WPS and About.

Link Information

This is the default screen after launching the Utility program.

Status: Shows the associated BSSID, which can be used to identify the wireless

access point.

SSID: Shows the current SSID, which must be the same on the wireless client and

AP in order for communication to be established.

Frequency: Shows the current frequency used for the wireless network.
Wireless Mode: Shows the current wireless mode used for wireless communication.
Encryption: Shows the current encryption mode used on the wireless network.
TxRate: Shows the current data rate used for transmitting.
Channel: Shows the current channel for communication.

6

Link Quality: Shows the link quality of the ENUWI-NX2 Wireless 802.11n with

the Access Point when operating under Infrastructure mode.

Signal Strength: Shows the wireless signal strength of the connection between the

ENUWI-NX2 Wireless 802.11n with the Access Point.

Data Rate:

number of packets transmitted and received.

Shows the statistics of data transfer, and the calculation is based on the

Configuration

This screen is where you set the basic wireless settings for the ENUWI-NX2
Wireless 802.11n.

Profile Name: Shows the Profile Name.
SSID: Service Set Identifier, which is a unique name shared among all clients in a

wireless network. The SSID must be identical for each client in the wireless
network.

Wireless Mode: There are two modes available for selection

● Infrastructure – to establish wireless communication with the LAN and other

wireless clients through the use of Access Points.

● Ad-Hoc – to establish point-to-point wireless communication directly with

other wireless client devices.

7

Authentication and Security: The following options are available: Open System,
Shared Key, WPA-PSK, WPA2-PSK, WPA EAP-TLS, WPA2 EPA-TLS . Select

Open System, Shared Key for WEP data encryption feature.

Open or Shared Key
Open System and Shared Key require the user to set a WEP key to exchange

data with other wireless clients that have the same WEP key.

z Default Key: select one of the 4 keys to use.
z Network Key: choose the encryption way, either in HEX or ASCII formats,

and enter the password in the blank space.

z Key Length: select 64 or 128 bits as the length of the keys

Key Format: HEX or ASCII

WPA-PSK / WPA2-PSK
If using the WPA-PSK/WPA2-PSK authentication method, please select the

Encryption type for TKIP or AES then enter the Passphrase key. The minimum

length is 8 characters.

8

WPA EAP-TLS
If using the WPA/WPA2 EAP-TLS authentication method, please select the
Encryption type for TKIP or AES then select the WPA/WPA2 Certificate from

drop down list.

9

Site Survey

This screen allows the user to scan for available wireless networks (wireless clients
and Access Points). It also allows the user to establish wireless communications
with an available wireless network.

Available Network – displays the wireless networks (wireless clients and access

points) that are within range.

Select any one of the wireless networks by double-clicking on it or clicking on the
“Connect” button.

Click the “Refresh” button to scan for available networks.

10

Profile

Profile – The user can create and manage the created profiles for home, work or

public areas. By double-clicking on one of the created profile, the setting will adjust
to the specific setting such as SSID, channel, and encryption as saved by that
particular profile.

Add: Adds a profile. The following screen will appear. The user can enter the

necessary information required for accessing Access Points or Wireless Router

Remove: Deletes the selected profile
Edit: Edit an exist profile. The screen will back to profile. Edit the SSID and select

the Wireless Mode, Authentication and Encryption then click Apply to save the

profile. When the Profile name was changed, a new profile will be added in the list.

Connect: Selected a profile from list then click the Connect to connecting to the

wireless network with the profile setting.

11

WPS

WiFi Protected Setup (WPS) is an optional certification program from the Wi-Fi
Alliance that is designed to ease the task of setting up and configuring security on a
wireless network. There are two methods used in the WPS as below instruction.

Push the button on my access point

Using the WPS configuration with the “Push the button on my access point”
method, the configuration steps as below:

1) Selected the “Push the button on my access point”.

2) Push the WPS configuration button on your wireless access point or router.

3) Click

the Next button start the WPS configuration.

12

4) If the WPS configuration was successful, the follow window will show on.

5) If the WPS configuration was failed, the follow window will show on.

13

14

Enter a PIN into my access point

Using the WPS configuration with the “Enter a PIN into my access point” method,
the configuration steps as below:

1) Selected the “Enter a PIN into my access point”, the PIN will be show on the

button of the windows.

2) Enter the PIN code into the WPS “Clint PIN number” of you wireless access

point or router then click the Start PIN button, the wireless access point or

router will start the WPS configuration process.

3) Selected a wireless access point or router which one will be connecting then

click the Next button start the WPS configuration. If the “Automatically select

the network” was checked, the setup step will be skip.

15

4) If the WPS configuration was successful, the follow window will show on.

5) If the WPS configuration was failed, the follow window will show on.

16

About

This screen displays information about the Wireless N USB Adapter, such as the
Driver and Utility version. When a new version of the utility becomes available for
upgrade, users will be able to identify by version numbers.

17

TECHNICAL SPECIFICATIONS

Hardware

Interface
Standards
Antenna
LED Indicator
Supported OS
Dimensions

(LxWxH)
Temperature

Humidity
Certification

Wireless

Module
Technique

Frequency

USB 2.0 Compliant
IEEE 802.11n draft v2..0, IEEE 802.11b and IEEE 802.11g
2X Integrated Printed Antenna
Activity
Windows® 2000, XP, Windows Vista™

86.5 x 30 x 13 mm

Operating: 0° ~ 40° C (32° ~ 104° F)
Storage: -10° ~ 70° C (14° ~ 158° F)

10% ~ 95% max (Non-condensing)
FCC Part 15.247 for US, ETS 300, 328 for Europe

802.11b: CCK (11 and 5.5Mbps), DQPSK (2Mbps), DBPSK
(1Mbps) 802.11g/802.11n: OFDM

2.412 to 2.484 GHz (Industrial Scientific Medical Band)

Media Access
Protocol

Data Rate (auto
fallback)

Output Power

Receiving
Sensitivity

Security

Channels

CSMA/CA with ACK

1, 2, 5.5, 6, 11, 12, 18, 22, 24, 30, 36, 48, 54, 60, 90, 120,
180, 240, 270, 300Mbps (auto sense) for Rx 1, 2, 5.5, 6, 11,
12, 18, 22, 24, 30, 36, 48, 54, 60, 90, 120, 135,150Mbps
(auto sense) for Tx

15dBm (typically) @ 802.11b
14dBm (typically) @ 802.11gB
14dBm (typically) @ 802.11n

135Mbps 10% PER @ -65 dBm (tytpical)
54Mbps 10% PER @ -68 dBm (tytpical)
11Mbps 8%

PER @ -84 dBm (typical)

64/128-bit WEP (Hex/ASCII), WPA/WPA2, WPA-PSK/WPA2­PSK

1~11 Channels (FCC); 1~13 Channels (ETSI)

18